Search Documents

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

By Charles W. Tandy, Wm. I. Weisman

Sodium sulfate is an important industrial chemical, being one of perhaps a dozen or so chemical commodities that are produced and consumed in the United States in quantities exceeding one million short tons per year. In recent years over half of the country's production of sodium sulfate has come from natural sources, whereas 20 years ago only 25% was derived from these sources. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, and the USSR. [Table 1] illustrates the growth in production of natural sodium sulfate in the United States. Mineralogy and Physical Properties Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Many of the saline or alkali lakes throughout the world contain varying amounts of sodium sulfate. In its natural form it is found as the hydrous salt, mirabilite, commonly called Glauber's salt, and as thenardite, the anhydrous variety. The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines, and it is from this source that much is extracted commercially. Sodium sulfate is also found combined with other compounds, such as the mineral glauberite, the double salt of anhydrous sodium and calcium sulfate, and blödite, the double salt of sodium sulfate and magnesium sulfate. While these and other minerals containing sodium sulfate are not economically important, they are of interest because of their frequent occurrence. The reader is referred to other publications (Cole, 1926; Dana, 1932; Grabau, 1920) for descriptions of these minerals. Only the two economically important minerals, mirabilite and thenardite, will be described herein. Mirabilite, Na2SO4 • 10H2O, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On

Jan 1, 1975

By L. Guttman, C. S. Barrett, J. S. Bowles

THE transformation from the face-centered cubic (Al) to the face-centered tetragonal (A6) structure in certain alloys of the indium-thallium system reported in the preceding paper1 exhibits many interesting crystallographic and metallo-graphic features, most of which presumably are similar to those of other cubic to tetragonal transformation such as, for example, the one which occurs in the chromium-manganese system,2 the one which, judging by microstructures and X-ray pat-terns,3 probably occurs in the copper-manganese system, the ones accompanying ordering in FePt,4 Copt,&apos; and AuCu,5 and the transformation near 115°C in barium titanate.6,7,8 If, as mentioned in ref. 1, the transformation is second order, the phases in equilibrium do not differ in composition, and it is both possible and likely that the mechanism is a diffusionless one. The present paper reports the results of a detailed study of the indium-thallium transformation and presents a theory for the atomic movements of the transformation which accounts for the observations. Experimental Crystallography of Transformation Markings The transformation from cubic to tetragonal in the indium-thallium alloys produces microstruc-tures of the type illustrated in fig. 1. These structures are observable either as relief effects produced on a smooth surface by the transformation, or after polishing and etching. These microstruc-tures are markedly similar to those found in copper-manganese alloys: iron-platinum alloys," and barium titanate,7,8 where it has been demonstrated that the lamellae are parallel to the (101) planes of the original cubic crystal. That the observed lamellae in indium-thallium alloys are also parallel to the (101) planes was proved by the following analyses performed on single grains in polycrystal-line samples containing 20.75 atomic pct T1. A study of the microstructures of a number of specimens revealed the fact that in many specimens the transformation markings continued unchanged in direction across the (111) interfaces of annealing twins. This at once demonstrates that the lamellae are parallel to a plane that is common to both parent and twin orientations, i.e., a plane in the zone <112>. This conclusion is compatible with the lamellae being parallel to (101) planes. To make a more complete determination of the habit plane of the lamellae, two grains were selected in which annealing twins ({Ill) twins) had been present in the high-temperature modification (cubic). The traces of the annealing twins, and of the transformation markings in both parent and twin crystals, were plotted together in stereographic projection, and a parent-twin pair of orientations was found that accounted for all lamellae as (101) planes. The projection of one of these twinned grains is reproduced in fig. 2. In view of these results the probability of there being another solution for the habit plane remote from (101) is very small, but to explore the possibility that the habit plane deviates slightly from (101), a more precise analysis was undertaken. In this, the orientation of a grain in the cubic modification was determined from a Laue back-reflection photograph taken with the sample at 90°C. The traces of the lamellae that formed in this grain on cooling were plotted in the stereographic projection

Jan 1, 1951

By Harry E. Cross

Kiln Products commissioned a Waelz kiln 4 metres in diameter by 75 metres long, in South West Africa in March, 1969, to recover nine in a form suitable for the production of electrolytic zinc. The raw material consists of a mixture of zinc silicate concentrates and zinc rich tailings purchased from an adjacent zinc mine - the mixture containing 20% to 25% zinc. The chemical composition of the ore is tabulated and the initial test results are described. Due to the comparatively low temperature at which the ore starts softening the kiln has certain unusual features to enable the temperature to be controlled within the necessary limits. A detailed description of the kiln, the starting-up problems and present operating conditions and results are presented.

Jan 1, 1970

By M. B. Ramachandra Roa

This paper records the results of the earth resistivity surveys made in the Godavari River in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented. Introduction The Government of Madras has under consideration the Ramapadasagar project which is estimated to cost some Rs.660,-000,000 (about two hundred million dollars). The most essential feature of this project is the construction of a high dam across the Godavari near Polavaram for impounding the waters of this great river of South India, whose maximum discharge is 2 million cu secs in flood time. It is estimated that when the proposed reservoir is constructed, about one million tons of rice could be produced annually under irrigation. To those who have had any acquaintance at all with the recent distressing famine conditions which India has passed through and is still undergoing, the Lounteous effects which this project will bring about to the country in the future, are obvious. In the region of the proposed reservoir, the river flows for several miles through a hilly tract, hemmed in between flanks of hard, solid rock; but the river bed is mostly sandy. A few bore holes put down in this sandy bed touched rock at a depth of 180 to 200 ft. The river bed is about jo ft above the mean sea level (m.s.l.) and the bedrock was found at —125 to —160 ft m.s.l. The crest of the dam is proposed at +162 ft m.s.l. The proposed dam mould therefore be about 120 to 130 ft above the river bed, and the foundations would have to reach down nearly zoo ft below the bed at the deepest part. A number of alternative sites were proposed for investigation, and it became necessary to quickly ascertain the bedrock topography at these sites. Dr. M. S. Krishnan,* who was consulted in the matter, furnished a detailed account of the geological features of the region and suggested a geophysical investigation which the writer carried out from February to April 1944, employing solely the electrical resistivity methods. The total length of the survey lines for the electrical measurements amounted to 62,600 ft and the number of resistivity determinations was about 2500. Altogether nine alignments for the dam were inten-

Jan 1, 1949

By C. G. Palagi, S. S. Stillar

The C. E. Weed concentrator treats 51,000 tons per day of 0.5% to 0.7% copper ore received from the Berkeley Pit, the Continental East Pit and the Butte underground mines. Improved operating techniques and conversion from semi-autogenous secondary grinding to ball milling have increased tonnage from an original design of 42,000 tpd. Separate treatment of sands and slimes, with recovery of soluble copper from the slimes, has increased total copper recovery. Concentrator tailings are pumped 600 vertical feet and 20,000 horizontal feet for disposal.

Jan 1, 1976

By A. E. Wheeler, H. Y. Eagle

The copper industry in the Province of Katanga, in the Belgian Congo, which is now controlled and operated by the Union Minére du Haut Katanga, had its inception many years ago in the vision of a Scotsman, Robert Williams, now Sir Robert Williams, Baronet. He it was who personally negotiated the mineral concession with King Leopold of Belgium, sent in the prospecting parties who located most of the present mines of the company, later arranged for the Belgian participation from which the present company was formed, and has been its active mentor ever since. The idea back of his efforts was the establishment of an industry on the Congo-Zambezi divide, of sufficient importance to draw up to it the head of the Cape to Cairo Railroad, the dream of Sir Cecil Rhodes, and the consummation of which he had left as a legacy to Mr. Williams, his successor. The reports of the prospecting expeditions showed that copper in profitable quantity was there, but many difficulties lay in the way of the establishment of the infant industry. The isolated location of the mines, various tribal wars, the Boer War, and many other factors contributed to making progress very slow. However, in spite of these difficulties the railroad was finally built and a blast-furnace plant erected at Lubumbashi, near Elisabethville, the capital of the Province. Operations of this plant were started in 1911, treating high-grade oxidized ores and producing pig copper by a reducing smelting. Production has been continuous since that time and the company has grown so that at present it ranks as the largest individual copper producer in the industry. It is a fitting monument to the foresight, optimism and driving force of its founder, and the progressive policies of his Belgian colleagues. In January, 1914, the Union Miniere du Haut Katanga engaged as its consulting engineer, Archer E. Wheeler, metallurgical engineer, at that time general superintendent of the Great Falls plant of the Anaconda Copper Mining Co. Mr. Wheeler was commissioned by the Board of Directors to proceed into Katanga, and make all necessary investigations to enable him to report on a comprehensive development program, and to recommend a scheme of treatment particularly for their low grade

Jan 1, 1934

By E. J. Rapperport, M. F. Smith

A presentation of the W-Ru constitution diagram is given. Techniques utilized in the determination of phase boundary values include electron micro-probe analysis of two-phased alloys and diffusion couples, as well as normal metallographic and X-ray methods. The primary features of the diagram are: 1) a terminal solid solution of ruthenium in tungsten with a maximum solubility of 23 at. pct Ru at 2300°C; 2) a terminal solid solution of tungsten in ruthenium with a maximum solubility of 48 at. pct W at 2205°C; 3) a o phase of maximum breadth about 6 at. pct based on the composition W3Ru2 which forms peritectically from the melt at 2300°C, and which decomposes eutectoidally at 1667 °C to form a twigs ten and 0 ruthenium; 4) a eutectic at 45 at. pct Ru and 2205°C with the products being o plus ß ruthenium. THE W-Ru diagram has previously been studied only in a cursory fashion. Raub and alter&apos; obtained a 1400°C isotherm in which they observed no intermediate phases, and on which they established the limits of solubility as 36.5 at. pct W in ruthenium and about 1.5 at. pct Ru in tungsten. In addition, Obrowski2 found a o phase forming peritectically from the melt and existing only above 1650°C. Below this temperature the phase was presumed to decompose eutectoidally. The present work finds the diagram as given in Fig. 1. I) EXPERIMENTAL PROCEDURE The materials used for alloy preparation in determining the W-Ru constitution diagram were 99.9 pct pure ruthenium powder supplied by Baker Chemical Co., and 99.9 pct pure tungsten powder from General Electric Co. Typical analyses of these elements are given in Table I. Initial alloys at 10 at. pct intervals were prepared from the metal powders by the following method. Powders sufficient for 25 g of the alloys were weighed out with an accuracy of 0.1 mg and blended mechanically. After blending, the powders were compacted, in a steel die, at approximately 30,000 psi. The compacts were sintered in an electric vacuum furnace in order to remove adsorbed gases and to achieve partial densification prior to arc-melting. Vacua of 10-4 mm Hg or less were maintained in sintering as the furnace temperature was raised to approximately 2000°C. Sintering times ranged from 10 to 20 hr. The sintered compacts were arc-melted under a protective atmosphere of purified helium. Melting was conducted on a water-cooled copper hearth, utilizing a nonconsumable tungsten electrode. In the melting process, each alloy was turned over and re-melted on opposite sides from four to six times to ensure complete melting and to eliminate gross in-homogeneities. The arc-melter used had a vacuum capability of 5 X 10-6 mm Hg, and a leak rate of about 20 -liters per hr. Chemical analysis techniques for refractory metal-platinum group metal combinations are not well-established; therefore, composition control and determination depended principally upon weight-loss observations and calculations. This consisted in weighing each alloy after sintering and after arc-melting, and calculating the maximum and minimum composition values, assuming the total weight losses to be first all tungsten, and then all ruthenium. Since composition uncertainty was directly related to weight loss, care was taken to minimize losses in handling, compacting, and melting. Prior to homogenization and equilibration the as-arc-melted alloys were analyzed in several

Jan 1, 1964

By William E. Ford, Edward Salisbury Dana

This section includes one distinct group, the Stibnite Group, to which orpiment is related; the other species included stand alone. Pyr., etc. - In the closed tube melts and gives a dark red liquid when hot and a red- dish yellow solid when cold; in the open tube (if heated ver slow? ) sulphurous fumes, and a white crystalline sublimate of arsenic trioxide. B.B. on ciarcoaTburm with a blue Hame, emitting arsenical and sulphurous odors. Soluble in caustic alkalies. Artif. - Realgar is frequently noted as a sublimation product from furnaces roasting ores of arsenic. Crystals are produced when arsenic sulphide is heated in a sealed tube with a solution of sodium bicarbonate. Obs. - Realgar occurs usually in veins associated with silver and lead ores. It has been found in volcanic regions as a sublimation~duct. It has also been noted as a deposit from hot spring waters. It is often rtasociate wlth orplment. It occurs at Felsi5bBnya, Kapnik and NagyAg, Hungary; Allchar, Macedonia. Binnental, Switzerland, in dolomite. In the United States, at Mercur, Utah; in the Norris Geyser Basin, Yellowstone Park, as a deposition from the hot waters. Found at the Monte Cristo millin district, Snohomish Co., Washington: the namerealga7 is from the Arabic, Rahj af gh&r,powder of the mine. Use. - Was used in fireworks to give a brilliant white light when mixed with saltpeter and ignited. The artificial material is now used for this purpose.

Jan 1, 1922

By Stuart S. Forbes

Changes and additions made to the Canadian Copper Refiners Ltd. electrolytic refinery between 1949 and 1955 are reviewed. The effect of high current density on current efficiency and section work is discussed. OPERATING and physical changes which have been made to the electrolytic tank house of Canadian Copper Refiners Ltd. suggest a review of present conditions. Previous papers1 a have described the general arrangement. Since then, expansion, closer anode spacing, and higher current densities have increased annual cathode capacity from 112,000 to 182,000 tons. A recent extension to the tank house, begun in the spring of 1954 and completed in August 1955, was undertaken to handle the monthly production of about 3,000 tons of anodes from Gasp6 Copper Mines. The anticipation of these additional receipts and large stocks of unrefined copper caused by the increase in custom smelting at Noranda made it necessary to increase production without immediately available additional cell capacity. Accordingly, from December 1954 through March 1955, the tank house was operated successfully at a current density of 24.0 amp per sq ft. Again, as of September 1955, one of the two tank house circuits is being operated at this high density. Although other refineries may operate at current densities higher than 24 amp per sq ft, none is doing so with anodes which contain silver and gold content as high as those being refined at Canadian Copper Refiners Ltd. General Arrangement The original building consisted of two parallel bays, each 660 ft long and 60 ft wide, with a 24 ft pump bay extending along the west side of the building. A previous expansion, completed in 1939, was to the west of the original building and consisted of two 60 ft parallel bays 240 ft long. The length of these two bays was extended in 1954 to 540 ft, adding one stripper and 12 commercial sections to No. 2 electrical circuit. Space is still available for an additional six commercial sections and one stripper section. Construction on these seven sections started in September 1955, and will be completed early in 1956. The tank house capacity will then be 206,000 tons of cathodes per year. In the two tank houses there is a total of 900 cells distributed as follows—commercial, 468; stripper, 36; total, 504 in the No. 1 tank house (No. 1 circuit): commercial, 360; stripper, 36; total, 396 in the No. 2 tank house (No. 2 circuit). Section arrangement consists of nine cells to a tier and two tiers or 18 cells to a section. Anodes, weighing 620 lb each, are cast with a Baltimore groove and are refined by the multiple system. Solution enters each cell through a bottom inlet at one end and overflows at the top of the opposite end. Rate of solution flow through the cells is controlled by valves at each section to 4.5 gpm. Electrical power to the tank house is now provided by nine 675 kw motor generator sets. Each set consists of a 135-12 v 5000 amp dc generator, driven by a 980 hp 2300 v synchronous motor. When No. 1 circuit is operated at 22,000 amp, five sets, at 4400 amp each, are connected in parallel. As the maximum allowable current on No. 2 electrical circuit has recently been set at 18,000 amp, only four sets are connected in parallel on No. 2 circuit. A tenth set, now being installed, will be reserved as a spare, for use in either circuit as required. Recent Changes In 1949, the annual capacity of the tank house was increased from 112,000 to 132,000 tons by closing the

Jan 1, 1957

By M. J. Humenick, K. Garwacka

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia that may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of injecting high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final cleanup process for ammonia removal from the ground water system. This paper details ammonia removal efficiency as a function of chlorine dose, reactant, and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1985

By John Devine

DURING the past few years the Bureau of Mines has been studying hydrogen-sulfide corrosion in the petroleum and natural-gas industries. Early work was confined to investigating the various practical, or operat-ing, factors that control the corrosion reaction when ordinary mild steel is being attacked. In that work it was shown that, if the optimum operating conditions1 are obtainable, . gas containing hydrogen sulfide can be handled at ordinary temperatures without serious corrosion resulting. However, frequently "sour" gas must be handled under other than optimum operating conditions, and combating corrosion then becomes a problem to be considered more during the construction of a system than during its subsequent operation. That is, where economi-cally practicable in such cases the designer will seek to substitute for mild steel other steels or ferrous metals more resistant to corrosion by hydro-gen sulfide. The comparative resistance of various commercial steels and alloy steels to corrosion by hydrogen sulfide at elevated temperatures has been reported systematically by previous investigators,2 but similar information for corrosion at ordinary temperatures is available only from scattered sources, representing different methods of testing. As the value of comparative corrosion tests depends largely upon the use of a

Jan 1, 1934

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.&apos;-4 Samsonov et al.&apos; reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami&apos;s Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By J. S. Johnson, W. C. McCulloch

All phases of plant operation must be synchronized so that the A number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units, parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shut- down. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow.

Jan 1, 1943

By L. W. Page

PREVIOUS to the introduction of the motor vehicle the broken stone or macadam road met the conditions of rural horse-drawn traffic better than any other type of road, but under fast motor traffic it has been proved to be quite unsatisfactory, and necessitates high maintenance charges. Such a road depends for its success upon the fact that the rock dust fills the voids between the stones and acts as a cement or binder. Under ideal conditions it should be constructed of rock so suited to the volume and character of horse traffic that only enough fine dust is worn from the stones of which the road is composed to take the place of that carried off by wind and rain; and when these conditions are met, the fine dust resulting from the wear. of traffic forms with the stone a smooth, impervious shell, shedding the surface water and protecting the foundation. With increase in the number and speed of motor vehicles, however, it was soon found that the cost of maintenance also increased, until at the present day highway engineers consider the old method of constructing and maintaining broken-stone roads increasingly inadequate, and are introducing every known type of binding material other than rock dust to cement the stone together. Among the most prominent types of products in use are those produced from our various petroleums. That the value of modern methods of road preservation was appre¬ciated in this country much earlier than we have been accustomed to believe is demonstrated by the recent revival of an old patent which was granted to one John Martineau, of Elbridge, N. Y., in 1834. Petroleum had, of course, not been discovered at that time, but he claims as his invention and improvement "The application of tar, turpentine, or any of that class of tenacious, cohesive substances, reduced before use to a fluid state, and that state used as a cement, to apply to, and combine with sand, gravel, pebbles, and pulverized stone, such as is used for a Mc-Adam road, or cobble stone, the interstices of coarser material being in all cases filled, as well as may be, with sand and gravel and cemented with tar or turpentine, to form the wearing face or surface of streets,

Jan 2, 1914

By K. Hanumantha Rao, A. Nayak, . K. S. Narasimhan, S. N. Mahapatra

Selective flocculation studies carried out with iron ore tailings generated at Kudremukh iron ore plant indicate that a concentrate containing 63% iron can be obtained from the tailings containing 34% iron with around 60% recovery. This opens up the possibility of recovering most of the iron lost in the tailings generated at 2 kt/h (2200 stph) while processing 22 Mt (24 million st) ore per year. This would mean that the productivity could increase by around 50%. In these studies, it has been established that caustic degraded tapioca starch is a most effective agent for selective flocculation. While potato starch after caustic degradation can also be used, neither the parent starch nor the amylopectin compound is as effective.

Jan 1, 1986

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form&apos;s (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,&apos; that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold&apos; discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By Richard D. Call

Predicting the performance of a waste embankment requires an estimate of the properties of the waste and foundation materials. The performance characteristics and the associated material properties are: [ ] Methods for obtaining estimates of the material properties include: laboratory and field testing, back analysis, and indirect estimates from other material properties. The most critical technical need is the development of indirect methods for use in feasibility studies and mine planning, prior to production when actual samples of waste material are not available. Material properties are not unique, single values; they are probability distributions. There are two components to these distributions: the uncertainties in testing and the inherent variability of the material. The objectives of a material properties evaluation should be to obtain an unbiased estimate of the property distributions rather than the average or the minimum value. Whether the current trend to a probability design analysis is followed or a simple sensitivity analysis is conducted, the unbiased probability distribution is preferable to single values.

Jan 1, 1985

By George H. Found

During recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" 06 a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating -mecha-nisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experi- mental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,&apos; damping due to localized inelastic stress relaxation at inhomogeneities within the meta1,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.&apos; How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables ham been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About Ioo hr. after straining, a stable value is reached of magnitude proportional to the amount of strain.&apos; In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By R. Wiesenthal

A method is developed for improving the low recovery efficiency which results when viscous oils are flooded by water. Viscous oil has been diluted with a lighter liquid miscible in it in any ratio which produces a mixture possessing a reduced viscosity and which is then displaced by water. Light gasoline was used in these tests to reduce the viscosity of the oil in place. Oils possessing viscosities in the range of 1.28 to 324 cp at the test temperature of 30C were displaced from a cylindrical unconsolidated sand core, with a length of 2 m (6.6 ft) and a diameter of 10 cm (3.9 in.) at a flood of 6.27 cc/sq cm/hr. In two test series up to I PV of light gasoline was injected into the core before water flooding. In the first series the recovery of a low-viscosity oil (1.28 cp) increased as the volume of light gasoline was increased. However, only the oil which could not be recovered by water flooding alone could be replaced by the light gasoline. In the other series, the recovery of a more viscous oil (13.5 cp) was not increased even if large quantities of light gasoline were injected. An oil bank built up ahead of the water front so that the flood water met with equivalent saturation conditions, as would be the case in flooding solely with water. However, the recovery of more viscous oils could be increased substantially when the core was first flooded with water, followed by a slug of light gasoline, and then flooded with water again. Furthermore, an oil bank ,built up ahead of the second water front. The formation of this oil bank is particularly favorable for the displacement process; the greater part of the light gasoline injected was pushed out of the core ahead of the oil and recovered. Using a light oil of low viscosity, it was possible to replace only the residual oil that could not be recovered by water flooding by the light gasoline. As the basic study had shown that highly viscous oils could be recovered by flooding first with water, then with light gasoline, followed by a second injection of water, the study was extended by tests made with reservoir fluids and cores taken from the low-gravity oil reservoir of the Wietze field, Germany. A great increase in recovery over flooding with water alone was obtained in these tests. The results may show a way to recover high-viscosity oils by a comparatively simple flooding procedure. INTRODUCTION In fields where oil recovery has not benefited from natural water drive, increased recovery may be obtained by the injection of water into the reservoir, especially in the case of fields which produce high-gravity, low-viscosity oil. There is a rather close relation between the viscosity of the reservoir fluid and the recovery that can be obtained by water flooding. As the viscosity increases the oil recovery decreases proportionately, so that an oil viscosity about 30 times that of water is generally considered to be the upper limit for an economically successful water flood.&apos; This limitation has been recognized theoretically by Buckley and Leverett,&apos; and has been verified by numerous laboratory flooding tests, such as by Croes and Schwarz,V n the viscosity ratio range of oil to water from 1 to 500. The reason for the inferior recovery of viscous oils by water flooding can best be understood by considering the mechanism of flood tests. In such tests water is introduced into one end of a sand-packed tube which is saturated with oil of the viscosity to be tested, and oil is produced from, the other end. Oil, with a viscosity lower than that of water, is pushed ahead of the advancing water with considerable uniformity, and irregularities in the displacement process tend to be eliminated as the oil saturation decreases and the water saturation increases. However, oil recovery is not complete, for the water forms interfaces with the oil and traps residual oil droplets in certain of the pore spaces. These residual oil droplets are distributed rather uniformly through the sand, and they are not susceptible to recovery regardless of the amount of water passed through the test cylinder. In the case of an oil possessing a viscosity greater than that of water, the injected water tends to move irregularly through the sand in the test cylinder. At the place in the sand where initial water movement takes place, resistance to the movement of water is lowered and the water finger so formed will grow perceptibly; it will extend to the outlet end of the test cylinder so that a breakthrough of water takes place long before much of the oil-saturated volume of the sand has come in contact with water. Once the breakthrough of water takes place, the water-oil ratio is gradually approaching the economic limit, even though much of the oil in the test cylinder remains unaffected by water. Disconnected drops of oil are trapped in the portion of the sand that has been invaded by water, just as when an oil of low viscosity is flooded. The poor recovery of the more viscous oils, therefore, is due to the irregularity of water movement through the test cylinder, and the rate of water movement through restricted sections of the oil-saturated sand increases with the more viscous oils. There are three ways whereby the recovery of viscous oils by water flooding can be improved:&apos; (1) adding materials which will increase the vis-

Jan 1, 1965