Search Documents

By Norman Brown, Victor V. Damiano

ThE present paper proposes a mechanism of dislocation multiplication at internal inclusions or cavities and presents experimental evidence of such sources in zinc. Using an etching technique recently described by Damiano, Tint, and Herman1 to study the three-dimensional aspects of dislocations in bulk zinc crystals, an investigation was made of helically shaped and closed-loop etch patterns found to be associated with inclusions. Crystals containing 0.1 pet Cd and grown from the melt were deformed slightly by bending and then aged at room temperature to precipitate cadmium at the dislocations. The crystals were cleaved along the (0001) plane and then etched with Gilman's2 etch. Crystals were continuously viewed on the (0001) plane while the etching was in progress and numerous helical and closed-loops etch patterns were continuously recorded as shown in the sequences printed directly from the cine film in Fig. l(a) and (6). These etch patterns are not to be confused with the etch patterns previously reported by Damiano and Herman3 which revealed dissolution spirals on the (0001) plane of high-purity zinc crystals. In the present case, precipitates arranged in the form of closed loops or helicies are progressively uncovered by etching after suitable aging of cadmium doped zinc crystals. Viewed with dark-field illumination as shown in Fig. 2, portions of a helical figure and subboundaries were revealed simultaneously. Continuous viewing while the etching was in progress revealed in Fig. 1(b) that the short line segments observed on single photomicrographs were in fact continuous and described a helix which had its terminus at an inclusion. The observations suggested that a dislocation once nucleated at the interface between the inclusion and matrix may act in such a way as to produce ad-

Jan 1, 1964

By Henry Howe

THE data which are collected in Table 1 show that the ferrite of low-carbon steel and of electrolytic iron, like the network of hypo- and hyper-eutectoid carbon steel, inherits, either absolutely or relatively, the, grain size of the mother austenite from which it is born in cooling through the transformation range. This evidence is so abundant and concordant as to cast doubt on Prof. Jeffries' 1 hypothesis of what might be called reversed inheritance, by which he explains Mr. Ruder's observation2 that the grains of a "slug of pressed pure electrolytic iron powder"were coarser, perhaps 12,000,000µ2, after a 3-hr. exposure to 1000° C. than after a 3-hr. exposure to 1250-1300°, when they were about 35,000µs. His explanation implies a natural tendency of coarser austenite grains to yield finer ferrite ones than spring from finer austenite grains, so that the inheritance is reversed. What seems to me a simpler explanation is that the enormous grains which followed the 1000° heating were not inherited from the mother austenite, but were formed by the process of natal coarsening, by means of which Stead and Carpenter developed grains of this same order of magnitude in this same kind of material, on heating to 950° or to 1000°, the temperature used by Mr. Ruder, provided the exposure was not unduly prolonged, and it does not seem to have been in Mr. Ruder's case. That their coarsening was natal and not through inheritance is shown first by the fact that their grain coarseness was out of all proportion to their relatively low temperatures and short periods, and hence was very far in excess of the grain size which the mother austenite must have had, and second and more cogently by the fact that the shape of these coarsened grains was evidently determined by the temperature distribution which existed during and immediately after the Ar3 transformation, that during the passage from the gamma to the non-gamma state.

Jan 9, 1917

By B. F. Fackenthal

At the session of the Bethlehem, Pa., meeting of the Institute, held in the Durham Cave, at Durham Furnace, on the afternoon of May 20, 1886, I exhibited some specimens of a fibrous white efflorescence which had exuded from the pig-iron at that time being made at Durham Furnace. As some of the members expressed an interest in the matter, I promised to have complete analyses made, and to report the result in a paper to the Institute. The presentation of the paper has been long delayed, but there appears to be no other literature on this subject, and it may still be of interest. The efflorescence was found to exude from the pig-iron where the pigs were broken hot from the sow; the entire fracture of both pigs and sow often being entirely coated with this material. Sometimes there was only a white surface, as if the ends had been daubed with white paint; but in most cases the material was found in small globules and in thin sheets. If the iron had been broken a little too hot, arid in consequence had " bled " on separating from the sow, some of the efflorescence would be found deposited 011 the iron-drippings, and on the incrustations of sand in the pig-bed. The globules were irregular in shape, some of them equivalent in mass to spheres three-eighths of an inch in diameter, but most of them much smaller. The thin sheets were also irregular in shape, and, although they were not porous, were often riot thicker than a spider-web. Some of them were produced by the peeling-off' of the thin coating on the pigs above referred to. They were opalescent in appearance, and some of them had an area equivalent to two square inches; but the largest pieces would fall apart in handling. Several ounces of the efflorescence could often be picked up, or scraped off the pigs, after each cast.

Jan 1, 1901

By Walter Henoch

THE subject of my talk is, "What 'the college, student expects when he gets out of college." Since all of us, here tonight are engineers, I think it will be proper to limit the discussion to "What the engineering student expects when he emerges from college." It might be well to con-sider just why we chose engineering rather than some other of the many courses open to us. We certainly did not choose it because it is easy nor because we thought it would be a very pleasurable way to spend four years of our lives. The majority of students who choose this profession have a pretty well-formed idea of what an engineering course requires. They at least know that they must work to re-ceive their credits. The minority, which is no small num-ber, are soon disillusioned and as a result they either quit college entirely or they join the' Commerce School. I asked a number of my fellow students just what it was that induced them to join the engineering profession, but it was hard to obtain a clear cut statement from any of them. Some said it was due to environment; others said, they took it because they liked it, and still others said they took it because their folks wanted them to. These state-ments are rather vague and incomplete, but underlying them all is something that the fellows found hard to ex-press. I think it is this: To the layman there is something of romance and adventure about the engineering profes-sion, and this fact coupled with the reputed high salaries and high commands of certain noted engineers no doubt fired our imaginations and consequently led us to join the ranks of the engineers. No doubt many engineers have gone out into the world and have found little romance or adventure .attached to their work, but nevertheless it is an occupation of a wide diversity of interest, of constant change of scene, and of vivid and human relations.

Jan 5, 1928

By W. J. McConnell

OBSERVATIONS on man exposed to unusual temperatures and humidities, and studies conducted under accurately controlled environmental conditions, have supplied information regarding the physiological responses of the human body which may occur incident to such exposure. These investigations also indicate the relative importance of temperature, humidity and air motion-the three physical air factors that affect human comfort. Many and diverse were the conclusions of early investigators who associated the discomfort observed in crowded and ill-ventilated spaces with changes in the chemical constituents of the air resulting from presumably poisonous exhalations from the body. These are of interest today only because, as a recent editorial in the British Medical Journal1 states, there is still an inclination to believe in the old view that there is some injurious quality of the air in ill-ventilated and crowded rooms, quite apart from dust, microbic infection and heat stagnation. There is a tendency to fly to some mysterious unknown agent such as "deionization," which even certain American engineers are now discussing. This editorial denies the existence of the least proof of any subtle poison being exhaled by human beings or of the ionization of the air having any influence in making open-window ventilation better and more stimulating than mechanical methods which propel heated and conditioned air through ducts. Until proof is forthcoming that certain changes, with which we are not now familiar, occur in the transmission of air from the exterior to the interior of enclosures, the responsible known factors which initiate the physiological responses in human beings are limited to the combined conditions of temperature, humidity and velocity of the air. While some mention was made as far back as 1880 that high temperatures and humidities were undesirable, Hermans,2 of Amsterdam, is credited with suggesting in 1883 that the harmful effects noted in ill-ventilated rooms were due to the fact that the increased temperature and moisture of the air prevented the body from maintaining a proper thermal balance.

Jan 1, 1930

By Herbert Ives

THE incandescent gas mantle is of considerable interest from the standpoint of temperature measurement because it presents a series of apparent contradictions to the established laws of radiation on which are based some of our best methods of temperature determination. One of these contradictions is that the mantle of least brightness (of the commercial thoria-ceria group) is the one having the highest temperature; this, though explicable without any violation of radiation laws, was long a stumbling block to the understanding of the performance of the mantle. Another anomaly is that the energy radiated by the mantle decreases with the rise of temperature, thus apparently invalidating total radiation methods of pyrometry, based on the fourth-power law. The discussion of methods of measuring mantle temperature which follows, is largely taken from an extensive study of the physics of the Welsbach mantle. 1 The incandescent gas mantle consists of a skeleton of refractory oxide of very light weight and open structure, formed by the ignition of a cotton or silk "stocking" previously thoroughly impregnated with salts of certain rare earths. The mantle of commerce is a mixture of approximately 99 parts of thorium oxide with 1 part of cerium oxide. This mixture, discovered largely by accident, gives luminous radiation many times greater than that from either of the constituents taken alone. It is customary to speak of the thoria as the "base" and the ceria as the "colorant," and the commercial mantle represents one of a family in which an oxide of low emissive power is employed as a base, which will assume a high temperature, while a small amount of some other oxide of high visible emissive power is added, which will reduce the temperature of the mantle but little. This is, in general, the most efficient- way, from the standpoint of visible emission, to utilize a substance of high emissive power in the visible spectrum. But it is not necessary. that two substances should be employed to produce a radiator

Jan 9, 1919

By A. B. Kinzel

ALTHOUGH vanadium is an important constituent of almost every brand of high-speed steel manufactured today, little is known as to its role in this series of alloys. The now standard 18 per cent tungsten and 4 per cent chromium constituents were the result of developments and improvements before 1903. In that year, vanadium was added to the steel by Dr. J. A. Mathews. This proved to be an outstanding con-tribution, so that the standard high-speed steel of today is generally referred to as the 18-4-1 type-18 per cent W, 4 per cent Cr and 1 per cent V. Various modifications have been attempted, since then, but with the exception of the introduction of cobalt, no striking improvements have occurred. Vanadium has been increased to 2 per cent in many of the common brands, and at least one brand contains 5 per cent V in addition to the usual tungsten and chromium. The carbon has been gradually increased so that it is not uncommon to find 0.80 per cent in the standard grade, although the carbon in the 5 per cent vanadium steel mentioned above is approximately 1 per cent, and even 1.2 per cent has been made experimentally. The role of vanadium has never been well understood, and although vanadium has been increased to 2.5 and even 5 per cent in certain high speed steels, it has not been generally established that the higher vanadium contents 'result in superior cutting properties. However, in all of the investigations, of which the writers are aware, the interrelation of the vanadium and carbon contents was not considered as a prime factor. The carbon content was held at 1.2 per cent or less-generally at the usual 0.65 to 0.75 per cent.

Jan 1, 1932

These springs arc situated on the south bank of the river about four miles below the City of Great Falls. In addition to the spring on the bank there are several in the bed of the river. Estimates on the flow of all these vary from 350 to 600 cubic feet per second, and as the temperature is practically constant at 53° F. throughout the year, the effect on the river water is to prevent the formation of anchor ice at the Rainbow Fails power development below, trouble of this source being in evidence every winter at the Black Eagle Falls above. Geologists claim that the water of the Giant Springs is derived from seepage through an old pre-glacial channel of the Missouri River now occupied by Sand Coulee, five miles up-stream from Great Falls. The water in this buried channel seeps through the flat-lying sandstone of the region and again unites with the present stream at the site of the springs.

Jan 1, 1913

By K. L. Meissner

It is well known that the so-called pure aluminum contains noticeable amounts of impurities, chiefly iron and silicon, and many investigators have studied the forms in which these impurities exist. Hanson and Archbutt1 state that iron exists in aluminum as FeA13 and silicon as elementary Si. The solubility of FeA13 in solid aluminum is practically zero, or at least so small that the smallest trace of this compound is always visible as a separate constituent. Under the microscope an untrained eye can hardly distinguish, without etching, the two constituents FeA13 and Si, but they can be differentiated by suitable etching reagents. Anderson2 also found the same results. At the same time, Merica, Waltenberg, and Freeman3 found a constituent of unknown composition. They found a small thermal effect, at 610" C., on the cooling curves of aluminum with small amounts of iron and silicon. The intensity of this effect increased with increasing silicon content, until an effect occurred at 576" C. due to the eutectic between aluminum and silicon. The authors ascribed the effect at 610" C. to a compound, which they call "X constituent." It was thought to be a ternary compound containing iron and silicon and could be observed under the microscope as dark particles. Dix4 has published unetched photomicrographs of an aluminum with 0.51 per cent. iron, 0.99 per cent. silicon, and 0.32 per cent. copper that shows three constituents: the dark Si (black in the figure), the lighter FeA13, which appears in half tone and crystallizes in needles, and a constituent of the same color as FeAL3 but of different crystal form, often resembling Chinese script. This last constituent, Dix thought, is a compound of Fe and Si; not the compound FeSi but a compound containing a relatively small amount of silicon. Therefore an alloy of aluminum. iron, and silicon (the copper should not be regarded in the following considerations) must contain the following four constituents: Al, FeA13, Si, and a compound of Fe and Si. This, however, does not agree with the laws of chemical equilibrium.

Jan 1, 1926

By W. Rostoker

A STUDY of the titanium-oxygen system' involved an associated series of measurements of the lattice parameters of the a and TiO phases. The results permit some interesting deductions which are herein reported. A comprehensive survey of the physical PI-operties of the phases in this alloy system has been made by Ehrlich.2 However, only impure titanium was available at that time, so that some revision of his measurements is to be expected. The lattice parameters were calculated from the high angle lines of Debye-Scherrer patterns taken in a 14 cm camera and using filtered CuKa radiation. The specimens were prepared largely by crushing and screening of lump samples which had been quenched from elevated temperatures. Only in the case of low oxygen contents was it necessary to resort to filing and annealing. The results of the lattice parameter studies are graphically presented in Figs. 1 and 2. It will be seen that oxygen produces a pronounced distortion of the c parameter of the a phase (hexagonal close-packed). The trend is in general agreement with Ehrlich's work, although the divergence of actual parameter values strongly suggests that his titanium was very impure. It will be noted that the a phase of titanium can tolerate the unusually high saturation solubility of about 34 atomic pct 0. By virtue of this unique effect, it is possible to make a calculation of the effective atomic diameter of oxygen when dissolved in a lattice with metallic bonding. This has not been possible before. Ehrlich's2 density measurements demonstrated that oxygen occupies interstitial positions in the a lattice and the trend of the lattice parameters would certainly support this. In a hexagonal close-packed unit cell the largest interstitial positions lie at (2/3, 1/3, 1/4) and (2/3, 1/3, 3/4). Accordingly, if both of these positions were occupied, the ratio of titanium to oxygen would be 1:1. The extrapolated c parameter may be taken as between 4.93 and 4.99?. The a parameter appears to reach a constant value of 2.955? at low oxygen contents. The distance of the center of a titanium atom site from the [vc2/16+a2/3-1.448] Then the atomic diameter of the oxygen atom is represented by the function: where the radius of the titanium atom is 1.448A,

Jan 1, 1953

By T. Prof. Egleston

How to interpret the composition of rocks has been a question which has caused a great deal of discussion and investigation among geologists and chemists. It is evident that that analysis will give the clearest results, which will give the relative proportion of the different minerals composing the rock as well as the weight of their different constituents. This, however, is a very difficult matter, and in those rocks which seem to the naked eye entirely compact, like obsidian and other rocks of that class, appears to be impossible. Cordier, in the early part of the century, invented a process which is known as the " mechanical analysis of rocks," which is really a method of mechanical preparation, and consists in crushing the rock to a certain fineness, and then, by virtue of their density, washing out the different minerals, so as to make a mineralogical analysis, separating completely the different constituents of the rocks. In the hands of so skilful a man, this was a comparatively easy matter, and Cordier found no difficulty in ascertaining the mineralogical composition of a rock. The ultimate chemical composition was ascertained from the sum of the elements contained in the different materials. In the light of to-day, it is very easy to see that the complete chemical analysis of the rock does not necessarily lead to the explanation of its character. It has been so difficult, however, to have any other kind of analysis made that most chemical examinations have been made as ultimate, and not as mineralogical analyses. The panning out of the different minerals composing the rock, which are often very nearly of the same specific gravity, is so difficult that a person of ordinary mechanical skill is scarcely able to do it; consequently the mechanical analysis which Cordier proposed, and was able himself so skilfully to effect, has never been practiced to any extent. A school was formed in France consisting of a very small number of Cordier's followers, which, in face of the difficulty of acquiring the method, very soon died out as a school, though some of his most skilful followers are still living. The next important step in ascertaining their composition was to out the rock into transparent sections and examine the minerals with

Jan 1, 1875

By Harvey S. Mudd

AMONG the highly skilled craftsmen of the Renaissance were those who worked with ores and metals. The author of this book, Vannoccio Biringuccio, was a master craftsman in the practices of smelting and of metalworking. Contrary to the customs of a trade, Biringuccio was moved to impart his knowledge to all and thus he has given us the earliest hand- book on metallurgy-in fact, the first printed book dealing with the applied metal arts and the processes of ore reduction. We should remind ourselves that metallurgy is an ancient art and then it fair1y may be said that Biringuccio sought to describe the techniques that had been in course of development since the Bronze Age of western civilization. Whether Biringuccio was a man of learning or a scholar according to the standards of his time we do not know, but today we recognize him as a man of science who gave his wisdom to succeeding generations. It was not until the coming of the Power Age at the end of the eighteenth century that progress was resumed in the science of which he wrote more than two hundred years before. Little is known of Biringuccio's training in his native Siena. It can be surmised that there, as in Florence, where his contemporary Benvenuto Cellini lived, he received his training in the craftsman shops where the industrial arts were taught and flourished alongside the fine arts. Perhaps he and Cellini were acquainted, although there is no mention of Biringuccio in Cellini's autobiography-an omission that Cellini's vast egotism makes understandable. He was the great artist, and Biringuccio was a practical, studious, unromantic figure with no favors to dispense. In the April 1940 issue of Mining and Metallurgy Dr. Smith describes Biringuccio's book under the title of "A Neglected Italian Metallurgical Classic." The article, revised and extended, forms the basis of the introduction to the present volume, and I urge all who take up Pirotechnia to read what Dr. Smith has written in the Introduction. Biringuccio's work is a classic and in its translation Dr. Smith and Dr. Gnudi have brought to bear the high degree of scholarship that it deserves. Dr. Gnudi made the translation at Dr. Smith's request and it was then refined "in the fire" of his scientific knowledge of the subject. The result is a book which the Institute is proud to place before its members and which the Memorial Fund Committee considers it a privilege to publish.

Jan 1, 1942

By M. E. Straumanis, R. P. Shodhan

LATTICE parameters of molybdenum of various purities are summarized in Table I. The latter shows that the parameter fluctuates between 3.1467 and 3.1475A. The room-temperature expansion coefficient a is also not well-known as values from 4.90 to 5.20 x 10-6 can be found in the literature.=-' It, therefore, seemed appropriate to repeat the measurements under exactly controlled conditions, using high-purity Hilger molybdenum powder (containing 0.0015 wt pct of Fe, 0.005 of Si and traces of other elements) and a 99.95 pct pure Sylvania Electric preparation (containing Cr, Fe, Ni, Si, Sn, and C in amounts of 50 ppm of each and in still smaller amounts Cu, Pb, Mg, and Mn). Of course, both samples could have contained at least 0.01 pct of oxygen in form of a surface oxide. However, oxygen, because of its small solubility in molybdenum, does not influence its lattice constant.g The determinations were made in a cylindrical precision X-ray camera, 64 mm in diam, the temperature of which was controlled within *0.05"C, by inserting it into a special thermostat." To exclude the film shrinkage effect (after the development of the film), the asymmetric film placement method was used." Absorption corrections (e.g., by extrapolation)" were unnecessary because of the use of a thin Li-B-glass fiber (about 0.08 mm in diam) which was fastened to the sample holder of the camera and dusted with the fine molybdenum powder. Cum radiation of the wavelength 1.389350 kX was applied because it produced in 30 min the line (420) having a high Bragg angle of about 81.6 deg. The conversion factor of 1.00202 gave the results in angstroms. To obtain the expansion coefficient a, exposures were made at various temperatures t, see Fig. 1, on at least two films at each temperature. The films were measured with a componator and the lattice constants a were calculated. The expansion coefficient was found from: where a2s is the constant at 25°C and A is the change in a and t. The same equation (knowing a) was used to reduce all the constants obtained at various temperatures to that of 25"C, Table 11. The probable error S507p (at a 50 pct confidence limit) was calculated from the reduced constants:

Jan 1, 1969

By C. S. Smith, Chih-Chung Wang

D. Turnbull—In the opinion of the writer the most interesting result described in this paper is that the distribution of tin with respect to solidification temperature has several fairly well-defined maxima. It appears that each peak may be associated with a catalytic impurity of some rather specific composition. Recently we have obtained some additional evidence in favor of this viewpoint in experiments on the supercooling of lead droplets coated with different surface films. The distribution of lead droplets, ostensibly coated with lead sulphate, with respect to solidification temperature exhibited two distinct and reproducible maxima, one at 20" supercooling and the other at 47". On the other hand, when the droplets were ostensibly coated with halide films, no solidification was perceptible until the aggregate was supercooled more than 55". Upon further cooling a single well-defined peak centering at 60" supercooling was observed. Since the particle size distribution was the same in these two sets of experiments it appears that the most reasonable interpretation of the results is that the sulphate surface film or its reaction products with lead are much more effective in catalyzing the nucleation of lead crystals than are lead halide films. C. S. Smith (authors' reply)—Dr. Turnbull's experiments with lead drops coated with various surface films are most interesting. However, before drawing conclusions from the cooling curves described in the paper as to the existence of a few nucleus types effective at a few different temperatures, one must consider the state of subdivision of the liquid metal. In the A1-Sn alloy used, the tin was not in uniform droplets but tended to collect in three distinct shapes—in long interconnecting prisms along grain edges, in somewhat elongated interdendritic branching pools. and in isolated droplets. A single nucleus will solidify only the metal in contact with it, and the heat evolved will be proportional to the connected volume. A uniform distribution of nuclei of random effectiveness in such an alloy will cause peaks on the specific heat curve on cooling, which correspond to the volume distribution of tin and tell nothing about the nucleus type. In any real alloy both effects will be combined, and it seems impossible at present to distinguish between them. M. B. Bever—The thesis of this interesting paper is supported by a combination of positive and negative evidence. The authors have shown that under certain conditions a liquid phase may undercool, if it is dispersed in a thoroughly discontinuous manner throughout a solid matrix. They also found that undercooling

Jan 1, 1951

Planning for a surface coal mine includes selecting the best means and equipment for uncovering the coal, loading it, and transporting it to the preparation plant. The machines and methods that will ensure optimum production will depend upon the location and characteristics of the seam to be mined. Stripping Techniques The choice of stripping units is influenced primarily by the system of mining, such as contour or out-crop mining as contrasted to mining in a region of rolling terrain with relatively flat upland surfaces. Factors such as the life of the mining operations production requirements, types of overburden, local and regional dip of coal, and land reclamation are other important considerations.

Jan 10, 1967

By AIME AIME

THE third award of the W. L. Saunders Gold Medal for "distinguished achievement in mining" has been made to John Hays Hammond. The two previous awards were to David Brunton and Herbert C. Hoover. Since the principal events in Mr. Hammond's interesting life are not only well known to his many friends but were summarized in the April, 1928, issue of MINING AND METALLURGY (p. 186), it seems most appropriate to reproduce here the chronological record of his career that appears on pages 67 to 69 of "A Student Reverie," by his friend and fellow Freiberg student, F. G. Corning. Mr. Hammond, after graduating from Yale in 1876, was a student at Freiberg for the next three years.

Jan 1, 1929

AN UNUSUAL OPPORTUNITY FOR INSTITUTE MEMBERS to increase or complete their sets of the Transactions. In order to encourage the custom of members increasing each year the number of Volumes of the Transactions in their private libraries until the sets are complete, the Board of Directors has authorized the sale of Transactions previous to the year 1913 at the following greatly reduced rates. This offer is made effective for sales made only during the year 1914, and applies only to members in good standing, and to libraries. The reduced price automatically ceases to apply to any volume when the total number of such volume left in stock is reduced to fifty (50).

Jan 12, 1913

Very few data are available about production in this county. The amount mined was used locally, or shipped by river, until 1839 when the canal was completed to Dunnsburg. Only partial records for four years remain of canal shipments. Considerable coal was used locally by the iron works at Farrandsville for some years. Rail shipments started in 1861 and those shown are the estimated shipments of these mines as compared with the mines in other counties served by the Philadelphia and Erie Railroad, the total tonnages being given in the annual reports to the Auditor General. It is not likely that any coal used by the railroad is included in these figures. (Table 40.)

Jan 1, 1942

By C. C. Spencer

A CHARGE of 12,200 lb of scrap was used on all heats. The slag materials that were added to the furnace along with manganese ore were kept constant; that is, 230 lb Coxey sand was put on the banks at the slag line before each heat was charged, 35 lb limestone was added after the carbon boil. manganese ore was the only item varied in the four series described herein. I might add here that it is impractical for us to get the carbon clown in one boil, for the steel would come out through the doors and run over the floor. We take the carbon down in two vigorous boils.

Jan 1, 1947

MINNEAPOLIS-HONEYWELL Regulator Co., and Trans-Weigh Co., have come up with a conveyor belt that thinks. The belt weighs material and then figures out the tons-per-hour that it carries. And you can't fool it by adding or subtracting material along the way. It makes allowances for any additional material as well as for any loss. The belt rides along a set of rollers. The force exerted on the rollers is transferred to a gage. The weight of the belt is subtracted electrically. Final measurements are fed into an electronic recorder which indicates the flow at the moment and the total amount which has been carried by the belt.

Jan 1, 1952