Search Documents

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

By Theron Wasson

Michigan has had another record year. Its production has been maintained by the development of fields discovered in 1938. Two minor fields were listed as discoveries in 1939. These are in the southwestern part of the state, where the greatest drilling activity took place. During the year 1465 tests were completed, of which 828 were oil wells, 56 gas wells and 581 dry holes. The four southwestern counties—Allegan, Ottawa, Kent and Van Buren—had 1077 tests drilled, while nine other southwestern counties had 70 tests, making a total of 1147 for this part of the state, 78 per cent of all drilled during the year. Michigan's production of 23,400,000 bbl. during 1939, equal to an average daily production of 64,110 bbl., exceeded 1938 by 4,655,000 bbl., thus establishing another annual record, which brought the cumulative amount for the state to a little over 125,000,000 barrels. A map showing location of Michigan oil and gas fields was published in the TRansactions in 1939 (Vol. 132, p. 353). Active Oil Fields.—The Walker field, near Grand Rapids, Kent County, had a rapid development during the year. Traverse limestone production was discovered here in September 1938, and development has been rapid during 1939. At the end of the year 5500 acres have been proved by drilling. The Traverse limestone is found in Walker field at a depth of about 1810 ft. The Temple field, Clare County, was the most active in Central Michigan. Its production is from the Monroe dolomite at a depth of 3890 ft. In this field 2500 acres have been proved by 125 producing wells. Michigan's largest producer for 1939 was drilled in the Temple field, with a rated potential of 8760 bbl. per day. The Wise field, Wise township, Isabella County, discovered in 1938, had a steady and orderly development because the operators agreed on a staggered 20-acre spacing program. So far 760 acres have been proved for production from the Dundee limestone, found at 3650 feet. Active Gas Fields.—The most active areas in which drilling was done during the past year for gas were the Freeman and Lincoln fields in Clare County, the Clayton field of Arenac County, and the Home field of

Jan 1, 1940

By Theron Wasson

Michigan has had another record year. Its production has been maintained by the development of fields discovered in 1938. Two minor fields were listed as discoveries in 1939. These are in the southwestern part of the state, where the greatest drilling activity took place. During the year 1465 tests were completed, of which 828 were oil wells, 56 gas wells and 581 dry holes. The four southwestern counties—Allegan, Ottawa, Kent and Van Buren—had 1077 tests drilled, while nine other southwestern counties had 70 tests, making a total of 1147 for this part of the state, 78 per cent of all drilled during the year. Michigan's production of 23,400,000 bbl. during 1939, equal to an average daily production of 64,110 bbl., exceeded 1938 by 4,655,000 bbl., thus establishing another annual record, which brought the cumulative amount for the state to a little over 125,000,000 barrels. A map showing location of Michigan oil and gas fields was published in the TRansactions in 1939 (Vol. 132, p. 353). Active Oil Fields.—The Walker field, near Grand Rapids, Kent County, had a rapid development during the year. Traverse limestone production was discovered here in September 1938, and development has been rapid during 1939. At the end of the year 5500 acres have been proved by drilling. The Traverse limestone is found in Walker field at a depth of about 1810 ft. The Temple field, Clare County, was the most active in Central Michigan. Its production is from the Monroe dolomite at a depth of 3890 ft. In this field 2500 acres have been proved by 125 producing wells. Michigan's largest producer for 1939 was drilled in the Temple field, with a rated potential of 8760 bbl. per day. The Wise field, Wise township, Isabella County, discovered in 1938, had a steady and orderly development because the operators agreed on a staggered 20-acre spacing program. So far 760 acres have been proved for production from the Dundee limestone, found at 3650 feet. Active Gas Fields.—The most active areas in which drilling was done during the past year for gas were the Freeman and Lincoln fields in Clare County, the Clayton field of Arenac County, and the Home field of

Jan 1, 1940

By Frank G. Norris

Slag control is adjustment of the composition of the slag, especially with respect to the FeO content. The theoretical method of slag control would be to charge a mixture of pig iron and scrap of given composition into the furnace, to melt always at the same carbon, and, after a uniform ore addition, to tap with a constant slag composition. Such conditions are not even approximated. Both scrap and pig iron are of variable, and, in many cases, unknown composition. The charge is oxidized to a variable extent during melting. The result is that the FeO content of the slag, and consequently of the metal at tap, varies over a wide range. In order to make a nearly uniform product, this variation must be compensated for in some way. One way is to adapt the ladle deoxidation to the requirements of the metal. The other is to control the slag. In a general sense slag control may be considered as a method of compensating for variations in the composition of the charge and in oxidation during melting. The method of slag control for low-carbon steel was developed by Dr. Herty at our Butler plant3. Use of this method enables the furnace operator to tap heats at a more nearly constant FeO content and, therefore, to use a more nearly uniform deoxidation practice. The desired FeO and the accompanying deoxidation will depend on the application of the product. This statement implies that 0.10 carbon steel finished with a 15 FeO slag may be essentially different from a 0.10 carbon steel finished with a 30 FeO slag. In making low-carbon steel, the desired carbon places a lower limit on the FeO content of the slag, because the slag must be sufficiently oxidizing for proper carbon elimination. With this degree of oxidation, the phosphorus specification is met without difficulty, and there is little danger of phosphorus reversion. Thus a limiting factor in high-carbon heats is of slight importance in low-carbon heats. For heats of 0.05 to 0.07 per cent carbon, the FeO content of the slag may be controlled at

Jan 1, 1935

By Roscoe C. Clark

In October 1945. R. F. Farris. in an AIME paper entitled Method For Drtermining Minimum Waiting OIL Cenzent Time, presented a method for caiculating the minimum WOC* time required in oil well cementing operations. Briefly. this method consisted of shutting in a well. after the cement had been placed and noting the time required fur the wellhead pressure to reach a. maximum. This time was then multiplied by a factor of 1.5 to determine when the cement had reached sufficient strength to support the weight of the casing. As a result of this work, a number of areas have reduced their WOC time ~Wuirements with the subsequent saving of considerable rig time. The tests conducted by Farris were, for the most part, conducted under cementing temperatures in excess of 70°F. This was done because in the overwhelming majority of cases. cementing temperatures are in excess of 70°F (only in tile northern part of the country. primarily in the Rocky Mountain ares. in cementing surface casing are temperatures below 70° F. encountered, and such temperatures occur only during the winter months). The Stano-lind Research Laboratory since that time has performed a number of tests both in the laboratory and in the field to evaluate this WOC factor when cemeriting temperatures are lower than 70°F. The results of these tests indicated the need for greater WOC time in areas affeaed by abnormally low cementing temperatures. These tests indi.cated that a woc factor of 2 (Time from start to mix cement to maximum wellhead pressure x 2 = Time to drill plug) will allow sufficient time for the cement to develop adequate strength. A field test under abnormally low cementing temperatures (surface temyerature 35°F., mud discharge temperature <70°F. and cementing depth 500 ft.) in the Rangely Field, "* using the WOC factor of 2, indicated the time to drill the plug as 45 hours. Well conditions preventing getting back into the well until a 48-hour WOC time had elapsed. At this time, the plug drilled firm to hard indicating that the cement had reached its final set. It is contemplated that during next winter additional field tests will be performed to further check the results of the laboratory and field tests conducted to date,

Jan 1, 1949

By Roscoe C. Clark

In October 1945. R. F. Farris. in an AIME paper entitled Method For Drtermining Minimum Waiting OIL Cenzent Time, presented a method for caiculating the minimum WOC* time required in oil well cementing operations. Briefly. this method consisted of shutting in a well. after the cement had been placed and noting the time required fur the wellhead pressure to reach a. maximum. This time was then multiplied by a factor of 1.5 to determine when the cement had reached sufficient strength to support the weight of the casing. As a result of this work, a number of areas have reduced their WOC time ~Wuirements with the subsequent saving of considerable rig time. The tests conducted by Farris were, for the most part, conducted under cementing temperatures in excess of 70°F. This was done because in the overwhelming majority of cases. cementing temperatures are in excess of 70°F (only in tile northern part of the country. primarily in the Rocky Mountain ares. in cementing surface casing are temperatures below 70° F. encountered, and such temperatures occur only during the winter months). The Stano-lind Research Laboratory since that time has performed a number of tests both in the laboratory and in the field to evaluate this WOC factor when cemeriting temperatures are lower than 70°F. The results of these tests indicated the need for greater WOC time in areas affeaed by abnormally low cementing temperatures. These tests indi.cated that a woc factor of 2 (Time from start to mix cement to maximum wellhead pressure x 2 = Time to drill plug) will allow sufficient time for the cement to develop adequate strength. A field test under abnormally low cementing temperatures (surface temyerature 35°F., mud discharge temperature <70°F. and cementing depth 500 ft.) in the Rangely Field, "* using the WOC factor of 2, indicated the time to drill the plug as 45 hours. Well conditions preventing getting back into the well until a 48-hour WOC time had elapsed. At this time, the plug drilled firm to hard indicating that the cement had reached its final set. It is contemplated that during next winter additional field tests will be performed to further check the results of the laboratory and field tests conducted to date,

Jan 1, 1949

By H. M. Howe, W. E. C. Eustis

THE processes which form the Subject of this paper have been experimented on in the laboratory of W. E. C. Eustis, but have not passed beyond the experimental stage. The first is the invention of Mr. J. L. Thomson, of Capelton, Quebec, Canada, the others have been invented by the writers. THOMSON&apos;S PROCESS FOR THE EXTRACTION OF NICKEL This consists essentially in first rendering the nickel magnetic, and then separating it from the materials. with which it is mechanically

Jan 1, 1882

By Vernon Taylor

CANADA&apos;S oil production is obtained almost entirely from the Turner Valley gas and oil field, in the Province of Alberta. This field, about 30 miles southwest of the city of Calgary and approximately 115 miles north of the United States border, supplied 92 per cent of production in Canada during 1937. In 1938 considerable development took place in this field and total production for the year amounted to 6,688,716 bbl., an increase of 3,922,146 bbl. over the production in 1937, which increased the percentage of production to approximately 97 per cent of Canada&apos;s total. In the British Empire, Canada&apos;s production is thus comparable to that of Bahrein Island and Burma, each of which produced approxi-mately 7,800,000 bbl. in 1937, being second to Trinidad&apos;s production of 15,500,000 bbl. The total production of the British Empire in that year amounted to 2.07 per cent of the world&apos;s total. HISTORY Development of the Turner Valley field commenced in 1913, when a well was started near a gas seepage on the banks of the South Fork of Sheep River in the central part of the Valley. This well found small quantities of a light crude oil in beds of Upper Cretaceous age and pre-cipitated a wild boom in 1913-1914 which ended with the beginning of the Great War in 1914. A small amount of drilling was done in the years from 1914 to 1922 and a few wells found small crude-oil production in the upper sands. In 1922 a few wells were started, including the Royalite Oil Company&apos;s No. 4 well (R, Fig. 1), which became the discovery well of naphtha pro-duction from the Paleozoic limestone. In October 1924, this well was completed at a depth of 3740 ft., being approximately 300 ft, in the lime-stone, with an initial flow of 600 bbl. of 72° A.P.I. gravity naphtha and 20,000 M cu. ft. of gas per day. Intense activity was not started until the latter part of 1928, when the Okalta No. 1 well (Q, Fig. 1) was drilled, with an initial production of 500 bbl. of naphtha per day. This well was only 1 ¼ miles from Royalite No. 4, but it was approximately 1300 ft.

Jan 1, 1939

C. A. Stetefeldt, Oakland, Cal.: It has always been assumed by the writer, and also by others, that the silver volatilized by roasting in a Stetefeldt furnace was a minimum as compared with roasting in other furnaces. Now, Mr. Morse records at

Jan 1, 1896

By R. R. Hart, B. C. Wonsiewicz, G. Y. Chin

In recent years there has been increased miniaturization of electromechanical devices to keep pace with current trends toward smaller electronic components. A major problem facing the designer, however, is the higher stresses encountered by the material as a result of shorter springs. Hence an improvement in the elastic limit, as approximated by the 0.01 pct offset yield strength, would be highly desirable. An increase of 25 pct in the yield strength, for example, will permit a 20 pct reduction in both the length and thickness of a cantilever-type spring while maintaining the same compliance. One technique of improving the yield strength that has received little commercial attention is crystal-lographic texture strengthening.1,2 Texture strengthening is expected to be most beneficial in materials of hcp structure, but considerable gain can also be expected in cubic materials. A wire with a (111) fiber texture, for example, is expected to be 20 pct stronger than randomly oriented material, and 50 pct stronger than wire with a (100) fiber texture.293 For sheet specimens with a {110}(112) texture, characteristic of many heavily rolled fcc alloys, the (111) transverse direction is expected to be the maximum yield strength direction, about 20 pct higher than that in the (112) rolling direction.&apos; In addition, the (111) direction is the direction of maximum modulus of elasticity for most cubic alloys. A large value of the elastic modulus could be desirable in designs where stiffer springs are required. To test the above idea, a 0.090 in. (-2.3 mm) thick commercial grade A (5 pct Sn) phosphor bronze sheet, a widely-used material for relay springs, was rolled from the spring-tempered condition (60.5 pct reduction) to various additional reductions up to a total reduction of 95 pct. Subsequently, additional material was obtained with a total thickness reduction of 97.3 pct Standard tensile specimens were prepared from the sheet material with the tensile axis parallel to and at 90 deg to the rolling direction. Tests were run on an Instron testing machine at a strain rate of about 0.050 min-l. Textures were determined by the use of the reflection pole-figure technique. Data were obtained using nickel-filtered CuKa radiation and with the aid of a Siemens pole figure goniometer. The X-ray pole figure studies show an incrzasing development of the texture toward the {110}(112) ideal

Jan 1, 1970

By C. E. Sims

IN an earlier paper by Sims, Moore, and Williams: data were given to show that hydrogen contents of 0.3 relative volume (0.00033 wt pct), existing at the center of 4-in.-square cast-steel coupons, could be removed by aging at 400°F for 125 hr. At the end of that time, complete restoration of normal ductility for the steel was obtained. Replicate specimens of the same steel were aged at room temperature up to 555 days or .18 1/2 months. At the end of that time, the hydrogen content at the center had fallen to 0.13 relative volume or 0.00015 wt pet, but there was no perceptible change in the ductility. On the basis of experience with accelerated aging of 1-in. and 4-in. coupons and room temperature aging of 1-in. coupons, it was predicted that, some time after two years and when the hydrogen content has been reduced to about 0.10 relative volume, there would be some recovery of ductility. One set of three bars remained, and these were held for 1310 days, or more than three years. Then tensile test bars were cut from the center, and these bars were sampled for hydrogen analysis at the time they were broken. The sample specimens were cylinders % in. in diam x 1 1/4 in. in length. The data showed that in this time the average hydrogen content had fallen to 0.096 relative volume or 0.00011 wt pct, and the ductility had increased sharply. Elongation had risen from 10 to 17.3 pct, while reduction of area increased from about 16 to 27.5 pct. On the basis of these data, fig. 1 was drawn to replace fig. 15 of the earlier paper. Extrapolation of the curves of fig. 1 indicates that it would require a period of about 2200 days or approximately six years at room tem- perature to reduce the hydrogen to the minimum value and to recover full ductility in the center of the coupons. The aging process apparently involves the movement of hydrogen from the interior to the surface of the bar and evaporation at the surface. This flux of gas presumably follows some diffusion mechanism, and an effort was made to use the aging data, obtained at room temperature and at 400°F, to calcu-late coefficients of diffusion, in the hope that they might indicate the nature of the diffusion. The conclusion was reached. however. that the data were inadequate for such a purpose.

Jan 1, 1951

By N. Brown, H. Green

The effect of quenching temperature and of aging temperature and time on compression stress-strain curves of ß brass was investigated. Age softening occurs at a rate which decreases with decrease of quenching temperature below the critical temperature for ordering. The activation energy for softening is 15,400 cal per mol. No matter how rapidly brass is quenched or what the temperature from which it is quenched, practically complete order is obtained at room temperature. It has been demonstrated that with respect to the specific heat,&apos;,&apos; electrical resistivity," X-ray diffraction, and microstructure, the slowly cooled and rapidly quenched specimens are the same and that complete long range order exists in both cases. However, Smith" showed that the hardness of ß brass depended upon the cooling rate and the temperature from which brass is quenched. Smith showed that the hardness was a maximum for specimens quenched from about 445 °C and that the as-quenched structure softened at room temperature at a rate depending upon the temperature prior to quenching. This softening after quenching is in this paper referred to as age softening. The results of this investigation are qualitatively the same as the findings of Smith. However, a more detailed analysis of these phenomena has been possible since the stress-strain curve offers a more sensitive index of the state of the metal than hardness. It is the purpose of this paper to show how the mechanical properties are related to the ordering of ß brass. A 200-lb ingot made from electrolytic copper and electrolytic zinc was extruded to 1/2in. rod. Chemical analyses at frequent intervals along the rod showed that the alloy contained 51.5 pct Cu with the greatest impurity being iron, at 0.01 to 0.001 pct. To obtain a constant test material, the 1/2in. extruded rod was warm-rolled to % in. diameter at 200°C and then recrystallized to a grain size of 2.0 mm. The specimens for the compression test were % in. high and % in. in diameter. The specimen ends were polished on 600 metallographic paper and coated with Molykote for a lubricant. The compression rig consisted of an anvil resting on the machined table of the Baldwin Southwark testing machine and a plunger fixed to the movable cross

Jan 1, 1954

By David R. Poirier

Activity data of carbon as a function of both temperature and composition throughout the stable austenite range is correlated by mearts of an equation derived from a quasi-chemical model. The carbon activity data of austmite for temperatures between 800° and 1200°C are utilized in conjunction with the activity of carbon calculated for the y solidus using the activity of carbon in liquid iron and published austenite-liquid equilibria. The results agree very well with Chip-man&apos;s correlation; however, a small difference in the activity of carbon in the high-temperature range of the austenite field is evident. Excellent agreement is found for the heat of solution of graphite in infinitely dilute austenite; from this study the value is 10,550 cal as compared with Chipman&apos;s value of 10,680 cal. AS part of a program to study microsegregation in dendritic solidification of ternary Fe-C-Cr alloys, it was desirable to be able to describe the equilibria between austenite and liquid iron in Fe-C-Cr alloys. In this regard, it was necessary to correlate existing data on the activity of carbon in Fe-C austenite as a function of both temperature and composition. At that time, Chipman&apos;s analysis1 of the thermodynamics of binary Fe-C austenite was not available. It will be shown that this study and Chipman&apos;s study agree rather well throughout the stable austenite range of temperature and composition; however, some small differences appear at temperatures greater than the eutectic temperature. Benz and Elliott 2 presented isoactivity lines for austenite superimposed on their revised Fe-C phase diagram. Using an expression from Darken and Gury 3 representing Smith&apos;s4 activity data between 800" and 1000°C, they found that the activities extrapolated above 1000°C to the solidus did not agree with the activities determined from the corresponding liquidus compositions. It is the purpose of the following argument to reconcile carbon activity data of austenite with the activity in liquid Fe-C alloys as determined by Rist and Chipman. 5 In addition, a simple analytical expression is sought for computational convenience. ACTIVITY DATA OF CARBON IN ZRON Fig. 1 shows the activity of carbon in Fe-C austenite as determined by Smith, 4 Schenck and Kaiser, 6 Scheil et a1.,7 and Bungardt et al.&apos; The lines are merely drawn to separate the data into the respective isotherms. These data are inadequate to determine the activity of carbon at temperatures greater than 1200°C. The activity coefficient in Fe-C liquid alloys was assumed by Rist and chipmans to obey the following

Jan 1, 1969

By R. M. Asimow

The magnetization curves for specimezs containing superparmagnetic particles are considered. It is shown that the curves may differ from a Langezlin function because of particle anisotropy, particle interactions , and the presence of a size distribution of particles. The various causes of particle anisotropy are considered, and magnetization curves for specimens with cubic and uniaxial anisotropy are presented. The magnetization curves depend on the In the particle-size below 100A it is quite difficult to obtain quantitative size and shape information on precipitate particles. All of the available techniques have their limitations; however, quantitative applications of superparmagnetism have not been developed as fully as possible due to a lack of analysis of the complete magnetization curve. With such an analysis it appears possible to obtain from a single magnetization curve of a specimen containing randomly oriented SPM (superparamagnetic) particles a quantitative volume distribution and a description of the particle shape.* sign of the anisotropy energy and in the case of a negative uniaxial anisotropy (prolate spheroids) the resulting curves may differ very considerbly from a Langevin function. A graphical technique is developed whereby it is possible to separate out the effects of the size distribution, the particle interaction, and the particle anisotropy. Thus it is possible to obtain quantitative values for both the particle shape and the size distribution. Langevin function2 I/Is = ctnh(HVIs/k T)-k T/HVIS [ 1 ] where I, is the saturation magnetization, V the particle volume, H the applied field, T the particle temperature, k the Boltzmann constant, and I the magnetization in the direction of the applied field. Such behavior is rarely if ever observed in actual systems. One explanation for this is that the SPM particles do possess a significant anisotropy and thus the magnetic energy associated with the particle depends on the direction of magnetization in a more complicated way than for the isotropic particle of Eq. [I]. In general the magnetic energy E of an isolated SPM particle embedded in a nonmagnetic matrix can be expressed as a sum of several contributions: E = Eh + Ed+Es+Ec [2] where Eh is the external field energy, Ed the energy resulting from the particle demagnetizing factor, E, the magnetostriction energy, and E, the crystalline anisotropy energy. In each term we consider only the part dependent on the orientation of the magnetization vector and the particle axes as the shape of the magnetization curve will be determined by these contributions. Following the same procedure used in deriving the Langevin function,

Jan 1, 1965

By J. W. Downey, M. V. Nevitt

MUELLER and Knott&apos; have reported that Ti2Cu has the Si2Mo-type (Cllb) structure. The lattice parameters of Ti2Cu and the positions of the titanium and copper atoms are given by them as follows: ao = 2.944A; co = 10.786A 6 atoms per unit cell: 2 Cu (a) 000; 1/2: 1/2, 1/2 4 Ti (e) 002; 1/2, 1/2, 1/2 + z 00 -2 ; 1/2. 1/2. 1/2- z where z = 0.341 We have found eight other binary compounds which appear to be isostructural with Ti2Cu. All of them involve the combination of a titanium group element with a copper group element or a titanium group element with palladium. The compounds and their lattice parameters are given in Table I. The alloy samples were prepared by arc melting metals having a purity of 99.9 pct or better. They were homogenized for 72 hr at 900°C in evacuated capsules and quenched in tap water. Filings were prepared, and these were reannealed for 4 hr at 700°C, also in evacuated tubes. The lattice parameters were determined by a least squares Bnalysis of the back reflection lines of patterns made with cobalt radiation. It was not possible to make a precise determination of the lattice parameters of Zr2Au because the filings underwent rapid oxidation at room temperature. The evidence supporting the large tetragonal cell containing 6 atoms involves the presence of the reflections 002, 101, 004, 112, 114, 202, and other reflections with higher indices for which I = 3n. Three or more reflections corresponding to these indices, which cannot be indexed on the basis of a small body-centered tetragonal cell containing 2 atoms, are observed in the patterns of all of the compounds listed in Table I. They are strongest and most numerous when the components have large differences in their atomic scattering factors, as is the case in Ti2Pd, Zr2Cu, and Hf2Cu. The values of the z parameter should be regarded as approximate They were selected on the basis of the best agreement between the observed intensities of two pairs of closely spaced powder pattern lines (004): (112) and (114): (202) and the corresponding intensities calculated for several values of z. An ordering scheme was assumed in which titanium, zirconium, or hafnium atoms occupy the titanium positions of Ti2Cu, and copper, silver, palladium, or gold atoms occupy the copper positions. Calculated and observed intensities of the aforementioned lines and the other lines of the patterns are in satisfactory agreement, but a refinement of the z parameters and a final confirmation of the ordering arrangement must await a more detailed study. It is interesting to note that in transition metal systems at A2B stoichiometry the Si2Mo-type structure competes for stability with two other fre-

Jan 1, 1962

By R. Maddin, R. Pond

THERE have been many recent studies of nonequi-librium alloy structures using specimens which have been formed by rapid solidification.&apos; The general methods for achieving nonequilibrium structure utilize high velocity impingement of a liquid metallic droplet(s) and one or more substrates of relatively high heat conductivity. Specimens formed by current popular techniques are small and have various forms of irregular geometry which severely limit their use for many measurements of physical or mechanical properties. As a result of geometric limitations most research has been restricted to X-ray diffraction, electron microscopy, and to a small degree, electrical resistivity. Recently several attempts in mechanical property evaluation have been reported.2,3 A technique for casting large quantities of regular, rectilinear, continuous metallic fibers has existed for a number of years.4 We have utilized this technique with some slight modifications to produce nonequi- librium alloy structures. The apparatus is composed of a small open tube furnace, a pneumatic cage which raises and lowers a graphite ejection mold, and a

Jan 1, 1970

By H. I. Aaronson

THE TTT-curve for the beginning of transformation in hypoeutectoid steels containing appreciable amounts of relatively strong carbide-forming alloying elements often exhibits a "bay" at intermediate temperatures. In many of these steels, proeutectoid ferrite is the initial product of the decomposition of austenite not only at temperatures above the bay but also in an appreciable temperature range below the region of the bay. Hultgren has postulated that ferrite formed above the bay, termed "orthoferrite", contains the equilibrium concentration of alloying element at temperatures above the eutectoid range, and the extrapolated metastable equilibrium concentration at lower temperatures. The ferrite formed below the bay, on the other hand, termed "paraferrite", was assumed to inherit completely the bulk alloy content of the austenite without regard for the compositional requirements of equilibrium. As shown schematically in Fig. 1, the two types of ferrite were taken to have different Ae3 temperatures and different C-curves on a TTT-diagram. Their different kinetic behaviors were thus considered responsible for the bay in the TTT-curve for the proeutectoid ferrite reaction in this type of alloy steel.

Jan 1, 1962

By R. M. Scafe

Although hydrogen has been intensively studied in its relation to steel quality, the methods of sampling and determinations are still open to question. It is true that various procedures have been proposed but actually there has not been sufficient agreement to establish a common base from which to work. As a result, it is difficult, to say the least, to correlate the reported results of some of the investigators in this field. The present symposium, premised on methods rather than effects, should prove of considerable value. For the purpose of this discussion two methods of sampling and analysis will be considered. First, sampling of molten steel in the ingot mold by use of an evacuated tube and cylinder using conventional methods of analysis for the gases collected; second, analysis by vacuum extraction involving the use of heating equipment and the determination of the amount of hydrogen evolved from solid steel samples by measurement at reduced pressures. Both methods have been used at Duquesne Steel Works and it is believed that either may be used with considerable benefit if the limitations of each method are recognized. Evacuated Tube and Cylinder Sampling devices for gases in molten steel suggested by various investigators range from very cumbersome and complicated devices to the relatively simple evacuated tube and cylinder used by Soler for deter- mining the CO content of the bath. This latter device was adopted (Fig. I) and modified to meet conditions at Duquesne Works. The principal modifications were in placing the cylinder at the side of the tube and the use of a sleeve on the immersion end of the tube. The first modification was made so that the cylinder could be readily detached and taken to the laboratory; the second, because of the difficulty encountered in obtaining an airtight seal after sampling and because of our practice of re-using the tube. Rigid control of the method of sampling and of the handling of the sample according to plan are of primary importance in hydrogen determinations. This applies to both the sampling of molten steel and the determination of the hydrogen content of cold steel samples. Except for a few preliminary samples taken from spoons, all work on molten steels using the evacuated tube was confined to the sampling and analysis of molten steel during the pour. As mentioned, uniformity of sampling was a basic consideration. As a result, every effort was made to follow definite sampling techniques and procedures. These included control of the depth below the surface from which the sample was taken, the timing between the shutoff and taking of the sample, as well as maintenance and care of the equipment. The distance below the surface at which the sample was taken was readily controlled bv means of a crosspiece and centering device attached to the tube. The steel was poured into the mold to the hot-top junction, the tube was then lowered into the 75

Jan 1, 1945

By J. B. Clark

An exploratory study of the 60 wt pct Mg and 80 wt pct Mg sections of the solid constitution in the magnesium-rich region of the Mg-Al-Ca-Zn system was undertaken. The objective of the investigation was to determine the general configuration of the phase fields with respect to the magnesium solid solution in this complex system. The 335°C (635°F) tetrahedron was selected for study because the solid constitutions of the bounding ternary systems—Mg-Al-Zn,1 Mg-A1-Ca,2 Mg-Ca-zn3—were well known and, at least in these ternary systems, diffusion was rapid enough at 335°C for equilibrium to be reached fairly rapidly. Metallography and powder X-ray diffraction were selected as the best corroboratory methods for determining the solid phase equilibria. A total of forty-six quaternary alloys on the 60 wt Mg and 80 wt Mg sections were prepared, annealed to equilibrium at 335°C, and the phases present identified. Singly sublimed (99.99 pct) magnesium, electrolytic (99.99 pct) zinc, high-purity (99.99 pct) aluminum, and USP calcium were alloyed in graphite crucibles under a chloride flux and chill cast into a split graphite mold. Alloy samples were sealed under argon in Pyrex vials and annealed at 335°C ± 1/2° for a minimum of 500 hr. At the conclusion of the anneal, the alloy samples were quenched rapidly in ice water. Standard metallographic procedures for magnesium alloys were used. Powder X-ray diffraction patterns were taken on a G. E. Camera with a diameter of 14.32 cm using nickel filtered copper radiation. The phase equilibria in the 60 wt pct Mg section of the 335°C (635°F) tetrahedron is shown in Fig. 1. The complex equilibria in the zinc-rich region were not accurately determined and are shown only tentatively with dotted lines. The equilibria of the three bounding ternary 335°C sections from pure magnesium to 60 wt pct Mg are also shown as though folded away from the tetrahedron. The 80 wt pct Mg section has the same configuration of phase fields as that shown in Fig. 1. Thus it is reasonable to conclude that in higher magnesium sections, the same relative configuration of phase fields is maintained though the relative proportions of the individual phase fields may change slightly as the magnesium solid solution is approached. Note that all the ternary phases present in these ternary diagrams enter into the quaternary equilibria with the exception of the phase of the Mg-Al-Zn system which becomes unstable with the addition of as little as 1/2 pct Ca. No quaternary intermetallic phases were found. No liquid phase was detected in any of the quaternary alloys annealed at 335°C suggesting that if a quaternary eu-tectic exists, it must lie between 335°C and 339°C, the temperature of the ternary eutectic in the Mg-Al-Zn system.

Jan 1, 1962

By R. B. Porter, R. P. Porter, R. A. Lothrop

Changes became necessary in dredging methods employed in Idaho through passage of the Dredge Mining Protective Act (1954). Among other provisions, the law requires dredge operators to construct settling ponds of sufficient capacity and character to reasonably clarify the water used in the mining process before such water is discharged into the stream. Porter Bros. Corp., a placer mining company with many years operating experience in Oregon and Montana, became interested in strategic mineral placers in Idaho in 1950 when it was learned that prospectors had discovered a radioactive mineral deposit in Bear Valley Creek, 95 miles northeast of Boise. The company acquired mining leases and proceeded with exploration and development work on the property. After extensive research had resulted in the determination of successful separation processes, contracts were negotiated with the federal government and deliveries of columbium-tantalum and uranium concentrates commenced in 1956. The mining operations are located in a primitive area of Idaho among salmon spawning grounds and crystal-clear mountain trout streams. To avoid involvement in a very controversial issue, it appeared advisable for the company to develop water treatment procedures exceeding those requirements stated in the Idaho Dredge Mining Protective Act. Operation: The company operates one 6 cu ft continuous bucketline dredge and one 4 1/4 cu ft continuous bucketline dredge on the property. The dredges are jig-equipped, with feed being screened to 3 in. by trommels. The screening and gravity concentration methods satisfactorily separate the heavy minerals from companion clays, sand, and gravel. However, this separation of the heavy minerals requires water from the dredge pond with a minimum content of silt and colloids; therefore, water for dilution is added continuously to the dredge pond to suppress solids buildup. Discharge of this highly turbid water to maintain the proper pond level would ultimately result in an excessive silt load in Bear Valley Creek. To prohibit the turbid pond water from flowing directly into Bear Valley Creek, it was necessary to isolate the dredging area. Main by-pass canals were constructed along each side of the dredge pond and numerous secondary canals were dug for diverting seepage and snow runoff. One by-pass canal, extending more than two miles along the west side of the valley, diverts the main stream as well as tributaries entering from the west; a canal east of the dredge area diverts streams entering from that direction. At the beginning of operations in 1956, the dredge pond effluent was filtered through tailings and settled by use of coagulents in a series of lagoons. The filtrate was then discharged directly into the stream. Although this procedure gave satisfactory results in conformance with the state law, ice buildup and lagoon freezing hindered the efficiency of the process during periods of low temperature. For this reason, testing began in 1956 on a water treatment process that would operate efficiently under the extreme weather conditions encountered in Bear Valley. Development of Water Treatment System: Porter Bros. Corp. established the following requirements for effective continuous treatment of dredge pond effluent to the stream which, at low flow conditions, effluent to the stream which, at low flow conditions, would not result in a turbidity exceeding 25 ppm in the stream, 2) produce a sludge sufficiently dense to minimize disposal area requirements, 3) be semi-portable to follow dredge movements, 4) be capable of operating at low temperatures, and 5) be capable of handling a variety of capacities and turbidities.

Jan 1, 1961