Search Documents

By N. S. Kenny, A. A. Burr

THE purpose of this note is to present evidence that vacancies, which have been produced by quenching from a high temperature, alter the rate of strain-hardening of an hep single crystal. The majority of investigations of the effects of quenched-in vacancies on the yield stress of metals have been made using fee samples in the form of thin wires. However, there is an inherent disadvantage in using such wires to study the effects of vacancies on the rate of strain-hardening of metals because fee wires begin stage II slip either immediately upon yielding or very shortly thereafter. When stage II slip occurs, very rapid strain hardening also occurs, masking the effects of vacancies on the rate of hardening. In this investigation single crystals of magnesium hep were studied since magnesium has only one slip plane at low temperatures and has, therefore, an extensive easy glide region. In addition, the effect of both static and dynamic recovery on the rate of hardening were eliminated by testing in liquid nitrogen. Both forms of recovery occur in hep metals by dislocation climb, which is a diffusion controlled mechanism and is negligible at liquid nitrogen temperatures. Finally, the dependence of the strain-hardening rate on the crystal orientation was eliminated by using the equations of Schmid and Boas.' Variations in the strain-hardening rate could, therefore, be attributed to the presence of vacancies. Single crystals in the form of rods approximately 5 mm in diam and 6 cm long were grown by a modified Bridgman technique from commercial high-purity magnesium (99.97 pet) supplied by the Dow Chemical

Jan 1, 1962

By R. J. Robbins, D. L. Anderson

A tunnel boring machine has potential use in al- most any type of mining where the access shaft (or adit) is large enough or can be made large enough for its initial entry and where the orebody is of sufficient size to warrant its use. Some time will inevitably be lost in negotiating curves or making lateral moves and moving from level to level. Nevertheless, if the orebody is sufficiently large, advance scheduling can minimize the lost time encountered in such moves. Ideally, a mine will be planned for the use of these machines, thus eliminating access and transport problems. From the viewpoint of time involved, the rate of advance by boring as compared to conventional means is worthy of review. For instance, the Blanco Tunnel, one section of the Bureau of Reclamation's San Juan-Chama Project in southern Colorado, was bored in competent sedimentary rock with the following performance:

Jan 7, 1967

By Lawrence Adler

A lag apparent in the mining engineering field. While mining will continue as an essential industry, a revitalized profession will be required for national well-being. Specific problems facing the profession include: - a conflict between its design, production and management components, which affect the engineers on a daily basis; - a credibility gap in public matters that is so extreme, government action approaches punitive in degree, and - historical decreases in the number of degree-offering departments in the face of an increasing demand for graduates. A turnaround in these areas could result in attracting into the industry, highly creative, capable, and socially concerned engineers. By improving the quality of undergraduate education, the effectiveness of each entering engineer would be multiplied. This is another way to combat the chronic shortage of trained mining engineers. At the same time, it would set a significant example for other professions in the throes of overspecialization. A revival of the mining profession can be accomplished only during the formative training years of its future practitioners. An educator's role would be pivotal in this effort.

Jan 3, 1975

By Frederick Prime

At the last meeting of the Institute, Mr. A. L. Holley read a paper on "Steel," in which he proposes for it a definition so opposed to the one generally received, as to call for some remarks. Until within the last five or six years there has been no dispute on the subject, and it seems worth while to investigate the matter. For not only does a proper tax on all importations depend on a proper appreciation of the term steel, but it is necessary to know whether steel, or wroughtiron, or homogeneous iron are requisite in all processes of manufacture in which malleable iron is employed, on accouut of cost, strength, etc. Karsten* says: "Iron may be obtained, either as an unforgeable, unweldable metal, which melts at a high heat, termed cast-iron ; or as a ductile, weldable, soft, metal, which can only be melted at the

By August Wendel

weight, and deflection, and recommends that the Pennsylvania Railroad Company denland that rails be made on specifications, based on these six variables, so narrow, that to fill them would cause the constant rejection of enormous quantities of steel, and a consequent enhancement of the price of rails, probably ten or twenty per cent., without any certainty that such rails would be any better than those the steel-mills are now making. I earnestly hope that the investigation which Dr. Dudley has so ably carried on will be continued. I hope the Pennsylvarlia Sailroad Company, or preferably a combination of several railroads, will institute the prolonged investigation which I think will be necessary to solve this deep problem; that they will take a hundred or more rails, watching and noting down carefully every detail of their manufacture as well as their analysis; that they will be carefully weighed before, during, and after service; that their crop-ends will be tested before service, and the rails themselves after removal; that all the sources of error which Dr. Dudley admits in the present investigation may be removed, and that enough facts may be gathered and tabulated so that the conclusions which may be drawn from them may be apparent to every one without labored discussion or heated argument. But I venture to prophesy that after this investigation shall have been completed, and a formula adopted which shall be satiefactory to both manufacturers and consumcrs, that formula will not be the one now under discussion. I hope Dr. Durlley will pardon me if I have been unduly severe in my criticism, and consider that I have written my remarks hastily and at a time which should have been given to needed rest. I differ with him only as regards the conclusions which he has drawn. I appreciate the value of his labors, and only make public my own conclusions in the hope of contributing to the advancement of the science of steelmaking, in which we are ail so deeply interested. Dr. August WENDEL, Troy, K. Y.: Dr. Dudley's last paper gives, certainly, very valuable and interesting information regarding the wear of rails under different conditions. His results concernillg the composition of rails, explotle, rather startlingly, some old theories regarding the wear of rails, and 1 think after his formula is silnplified it will be one good formula to work by. As he now arrives at the same conclusions reached ill his first paper, some of my remarks will apply to both, althougl~ I would

Jan 1, 1881

By Frederick Prime

AT the last meeting of the Institute, Mr. A. L. Holley read a paper on "Steel," in which he proposes for it a definition so opposed to the one generally received, as to call for some remarks. Until within the last five or six years there has been no dispute on the subject, and it seems worth while to investigate the matter. For not only does a proper tax on all importations depend on a proper appreciation of the term steel, but it is necessary to know whether steel, or wrought-iron, or homogeneous iron are requisite in all processes of manufacture in which malleable iron is employed, on account of cost, strength, etc. Karsteu* says : " Iron may be obtained, either as an unforgeable, unweldable metal, which melts at a high heat, termed cast-iron; or as a ductile, weldable, soft metal, which can only be melted at the * Karsten, Handbuch der Eisenhüttenkunde, 3d ed., vol. i, p. 6. Berlin, 1841.

Jan 1, 1876

By W. C. Winegard, C. Elbaum, T. Ojala

NONOCTAHEDRAL slip was observed in poly- crystalline aggregates of aluminum by Boas and Ogilvie.&apos; These authors indicate that the non-octahedral slip takes place on (100) or (110) planes. Ogilvie2 studied the continuity of slip lines across grain boundaries in polycrystalline aluminum. Non-octahedral slip was observed by him, but it was not reported to occur in the continuous slip lines across the grain boundaries, which were identified as octahedral slip in all cases. The present note reports the observation of non-octahedral slip in the grain boundary region of an aluminum bicrystal and tricrystal, both deformed in tension at room temperature. An analysis is made, which leads to a probable identification of the non-octahedral slip planes as (110) and (331). The specimens used were of rectangular cross section, approximately 5x10x200 mm. They were prepared by growth from the melt, using aluminum reported by the manufacturer to be 99.994 pct pure. The grain boundaries were in a plane perpendicular to the wider face and parallel to the long dimension of the specimens. The axis of tension was also parallel to the long dimension of the specimen. The orientations of the specimens studied were determined by the Laue back-reflection method and are given in Fig. 1. The nonoctahedral slip was first observed after about 6 pct extension in the bicrystal, and after about 2 pct extension in the tricrystal. The micrograph, Fig. 2, of the grain boundary region of the bicrystal shows two active slip planes throughout each of the two crystals, with a third plane active at the grain boundary in each crystal. Two major sets of slip traces observed in grain No. 1 are consistent with the operation of the slip systems (ill) [oil] and (111) [011]. The nonoctahedral slip takes place on a plane belonging to a <111> zone, as determined by drawing trace normals. Assuming that slip will take place only in the <110> direction, the planes in the <111> zone, which do not contain that direction, need not be considered. Among the remaining prominent planes of that zone, the (011) plane has a common slip direction—the [011]—with the (111) plane, which acts as one of the octahedral slip planes. In grain No. 2, a similar situation to that in grain No. 1 is observed. As indicated previously, the (oil) plane in the <111> zone, to which the nonoctahedral slip plane belongs, has a common [Oil] slip direction with the acting (ill) slip plane. Also, the orientation of the (oil) plane in grain No. 2 almost coincides with the orientation of the acting (111) slip plane in grain No. 1. Similarly, the orientation of the (oil) plane in grain No. 1 almost coincides with the orientation of the acting (111) slip plane in grain No. 2. It is, therefore, possible that the nonoctahedral slip was induced, in both cases, by octahedral slip in the neighboring grain. It is important

Jan 1, 1957

By J. E. Flinn, E. R. Gilbert

Recently, Green reported some high-temperature, 0.60 to 0.89 T3, creep results on unalloyed tantalum. From his study he determined an activation energy of 114 kcal per mole for steady-state creep using the T, differential-temperature method25 for testing. He accounted for the difference between this value and 110 kcal per mole for self-diffusion by the temperature dependence of the elastic modulus, 4 kcal per mole. This reported activation energy is in apparent disagreement with that which can be determined from Green&apos;s isothermal data, which we have plotted as log creep rate vs 1/T in Fig. 15. From this figure, it appears that there are two activation energies of -185 kcal per mole at the higher temperatures and -75 kcal per mole at the lower temperatures. It is not obvious that the data can be fitted to a straight line corresponding to an activation energy of 114 kcal per mole. One is led to two possible conclusions regarding Green&apos;s study: there are two discrete processes controlling the creep rate from 0.60 to 0.89 Tm or the apparent activation energy is not discrete but continuously increases with increasing temperature. The former speculation would be in closer agreement with the high-temperature creep behavior of tungsten.28 The apparent disagreement between the activation energies determined by the AT and isothermal methods certainly suggests that further study on the high-temperature creep of tantalum is needed.

Jan 1, 1967

By B. H. Bergstrom, Will Mitchell, T. G. Kirkland, C. L. Sollenberger

In a previous article&apos; the authors outlined a study I of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated.

Oct 1, 1955

By W. W. Odell

THE sulfur content of coal is perhaps more important in the manufacture of illuminating gas than in any other coal-using industry. Whether the gas is made by the distillation of coal in retorts or ovens or by steaming incandescent coal or coke in the water-gas process, a portion of the sulfur present in the fuel always passes into the crude gas. Practically all the sulfur that remains in the finished gas is transformed into sulfur dioxide (SO2) when the gas is burned. Sulfur dioxide is a pungent suffocating gas and, if present in the air in any perceptible amount, is deleterious to health and comfort and damaging to house furnishings. So universally is this recognized that laws regulating the amount of sulfur that may be permitted to remain in the gas are very generally in force. The capacity of a plant to purify gas frequently limits the selection of coal for gas making. This condition may arise from different causes. Some plants were originally designed to handle a certain grade of low-sulfur gas coal, and very little leeway was allowed for growth or for the use of inferior coals. Other plants, when built, had ample capacity to purify gas from relatively higher sulfur coals, but their output has grown so rapidly that their purifying capacity is now limited and only- the low-sulfur coals can be handled. There is a great quantity of coal in the United States that would satisfy the requirements of the gas manufacturer, were it not for the high sulfur content. The coals containing less than 1 per cent. sulfur are becoming scarcer year by year and, in time, the gas industry will probably be compelled to use coals that are now considered out of the question.

Jan 9, 1919

By Harry Tufft

FOR many years the treatment of mine timbers with preservatives was confined to a few pioneer plants in the United States, and it is only in the past few years that the practice has grown appreciably. In a field study of the mine timber situation in Illinois, Pennsylvania, and further study of the situation in the country as a whole, I found that most mine operators did not keep records on mine timber that would afford the necessary data for determining the possible savings from preservative treatment. Some primary questions the mining engineer should be able to answer before making his decision on preservative treatment. for a particular mine are: (1) Quantity and cost of timber going into permanent workings annually; (2) quantity and cost of annual replacements due to decay; (3) life of untreated timber in different places; (4) desired life of timber. With the necessary facts in hand, he can then con-fidently select a method of treatment and preservative that is best suited to his needs. In former years when timber was cheap and an abundant supply could be had close at hand, as was the case in the majority of mining regions, the mine op-erator did not concern himself much except to see that enough was supplied to keep the workings safe. The cost figure for timber and labor, distributed to cost per ton of ore, was all the bookkeeping necessary. With present costs of timber, labor, and increasing length of haul to the mine, many operators are paying closer attention to timbering costs and studying them in. more detail. Some of the larger and more progressive opera-tions now keep detailed&apos; figures that give information on all phases of their timber problems. However, at the majority of mines the data available do not permit such analysis. Checks as to where the different con-signments are placed, the date of setting, and the period

Jan 6, 1927

By C. Y. Ang, C. Wert

Quench aging of supersaturated solid solutions of nitrogen in columbium takes place in reasonable times in the temperature range 300&apos; to 500°C. Changes in internal friction, hardness, and electrical resistivity are found to accompany this change. THERE is practically no detailed information in the literature concerning interstitial solid solutions in either columbium or tantalum. The fact that both of these metals are used extensively commercially in both pure and alloyed states makes studies of their properties of value. While the plan is to study both these metals and their alloys extensively, so far only a small number of measurements have been made. This paper presents data obtained in the initial investigations of columbium. The principal interstitial impurities of columbium are likely to be hydrogen, carbon, oxygen, and nitrogen. The first of these, hydrogen, is outside the scope of internal friction measurements at present and nothing quantitative is known about the initial hydrogen content of the specimens. However, it is believed that it is completely absent after the preliminary heat treatments are carried out. The carbon content of the original samples is low and can be reduced still further during sample preparation. Oxygen is normally present to some extent in columbium and can also be added or removed easily. Nitrogen is also normally present in small amounts and can also be controlled within limits. Since it is not possible yet to remove all the nitrogen from columbium and since it is possible to remove essentially all the oxygen and carbon, initial measurements were made on the alloy system nitrogen in columbium. In this sense then, the alloys are true binary alloys. Little is known about the effects of nitrogen on the physical and metallurgical properties of columbium, so it was necessary to perform some rather elementary measurements on the specimens. These measurements are described briefly in the next section and are discussed in detail in later sections. Scope of the Work That internal friction is associated with diffusion of nitrogen in columbium has been known for some time. It is similar in nature to that for carbon and nitrogen in a-iron. In these latter cases, the information obtained from internal friction has been useful metallurgically.&apos; and it is not too much to expect useful information from similar studies on columbium containing nitrogen. The technique of internal friction measurements is adequately described by Ke2 At a frequency of 1 cps the internal friction peak for nitrogen in columbium occurs at 300°C and that for oxygen at 160°C." So that all the measurements will be meaningful metallurgically, the internal friction has been calibrated by making a measurement of the damping at the two peaks and a measurement of oxygen and nitrogen content by chemical analysis. A comparison of the two gives the following calibration factor: To go from damping capacity expressed in terms of 1/Q to weight percent of oxygen and nitrogen in solid solution in columbium, multiply the peak values of internal friction by about 4 and 3 respectively." Data from which these factors were calculated are presented in Table I. The increase of electrical resistance of columbium caused by the addition of oxygen and nitrogen as interstitial impurities has been quantitatively determined. At room temperature the percentage increase is small for small additions of impurities (<0.1 wt pct); as the temperature is lowered it becomes an increasingly larger factor of the total resistance. An empirical relation has been established to express the resistivity at — 195°C in terms of weight percent of oxygen and nitrogen in solid solution. It is easy to make supersaturated solid solutions of nitrogen in columbium and to observe aging phenomena. The optimum aging temperature, as in the case for carbon and nitrogen in a-iron, occurs at the temperature for which the time necessary for a single place-change in diffusion is about 1 to 10 millisec. This means for nitrogen in columbium that significant property changes should take place for this alloy at about 400" to 500°C in reasonable time intervals. Results of such aging experiments are

Jan 1, 1954

Ernest R.. WOAKES, Cana, Colombia: The allusion in this paper, under the heading " Mining on the Isthmus," to the Espiritu Santo mine at Cana is neither according to fact nor worthy of the most interesting and able summary of the mining districts of Colombia contained in the remainder of the paper. The following remark is certainly open to contention: "The most widely-known mine of this department is the Espiritu Santo, at Cana, a quartz-mine opened up in 1680 and abandoned in 1727 on account of the attacks of the Cana Indians. This mine undoubtedly produced great quantities of gold, although many of the accounts given of its ancient richness are probably exaggerated. In 1884 it was rediscovered and reopened by the Darien Gold Mining Company, and under the able management of Mr. Thomas H. Leggett, now prominent in South African mining circles, produced for a time successful results ; but later the veins became pockety and the output unsatisfactory." The mine here referred to, though situated at Cana, was not the Espiritu Santo mine, and was closed down in 1892. Mr. Leggett, however, ran ten stamps on the ore from it for some two or three months in the year 1890, when he left Colombia. The Espiritu Santo mine was not reopened by the Darien Gold Mining Company until the year 1894. For the last three years the ore from the old Spanish workings of this mine has been yielding in the mill 1 ounce to the ton, and has served to keep the mine going whilst extensive development-works have been

Jan 1, 1899

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported&apos; that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200&apos; to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

Discussion of the paper of ALBERT SAUVEUR, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2439 to 2449 G. K. BURGESS, Washington, D. C.-This very instructive contribution by Professor Sauveur to our knowledge of that puzzling substance, Hadfield&apos;s manganese steel, should not only be read in connection with the paper of Messrs. Hopkinson and Hadfield referred to by Professor Sauveur (Bulletin No. 87, pp. 513 to 530, March, 1914); but one should also have in mind, as throwing much additional light upon the questions raised, two papers recently presented before the Iron and Steel Institute, the one by Sir Robert Hadfield (Journal of the Iron and Steel Institute No. II, 1913) on Heating and Cooling Curves of Manganese Steel, the other by Messrs. Hadfield and Hopkinson (ibid., No. I, 1914) treating of the Magnetic and Mechanical Properties of Manganese Steel. We then have brought together for this substance, the thermal, magnetic, and mechanical properties as well as the resulting microstructure, for the definite heat treatments described, and in particular after long annealing between 500° and 700° C. Sir Robert Hadfield and Professor Hopkinson see in the properties found for manganese steel (of C = 1.25 and Mn = 12.5 per cent.) a demonstration of the untenableness of the allotropic theory of iron, whereas Professor Sauveur reaches the contrary conclusion, that some of the facts observed can be explained only in terms of the existence of beta iron in steel of this composition. There is another possible hypothesis: namely, that these several series of experiments shed no light on the subject of the allotropy of iron, or at least as regards the existence of beta iron. However heretical it may sound, I am inclined to this last belief.

Jan 4, 1915

By T. M. Morris

THE following data have been compiled from in- formation submitted by 24 plants in answer to a questionnaire sent to cyclone manufacturers and to companies using cyclones for wet classification, either for closed circuit grinding or for desliming.

Jan 8, 1957

By Carl H. Unruh, D. L. Katz

Experimental data are presented for hydrate formation conditions for gas mixtures of carbon dioxide and methane. Equilibrium constants for carbon dioxide, defined as the mole fraction of carbon dioxide in the gas phase (dry basis) divided by the mole fraction of carhon dioxitle in the hydrate (dry basis)... were calculated usine the equilibrium constants for methane developed in an earlier paper. INTRODUCTION A series of papers have been written on gas hydrates, giving temperatures and pressures at which hydrates would form.2. 3, 4. 5, 6. 9. 12, 13, 15 Vapor-solid equilibrium constants have been developed for methane, ethane, propane and iso-butane&apos; by which it is possible to compute for a specific gas mixture the temperature and pressure at which hydrates will form. Carbon dioxide is present in many natural gases in concentrations usually from 0.1 to 2.0 per cent. It also forms a gas hydrate with water and presumably enters the solid solution when present with a natural gas which is forming a hydrate. The equilibrium constant giving the ratio of the concentration of carbon dioxide in the gas phase to the concentration in the solid phase is required for including the effect of the carbon dioxide when computing the conditions for hydrate formation. Direct determination of the concentration of carbon dioxide in solid hydrate requires a difficult separation to be made. Therefore, this research resorted to the measurement of the temperature and pressure at which specific mixtures of methane and carbon diox- ide would form hydrates. From the equilibrium constants previously mentioned for methane, it is possible to compute the equilibrium constant for carbon dioxide, without measurement of the composition of the solid phase. Fig. 1 shows the conditions at which methane and carbon dioxide form hydrates. The methane curve FG extents to some high pressure while the carbon dioxide curve AB intersects the vapor-liquid water-liquid carbon dioxide

Jan 1, 1949

By Carl H. Unruh, D. L. Katz

Experimental data are presented for hydrate formation conditions for gas mixtures of carbon dioxide and methane. Equilibrium constants for carbon dioxide, defined as the mole fraction of carbon dioxide in the gas phase (dry basis) divided by the mole fraction of carhon dioxitle in the hydrate (dry basis)... were calculated usine the equilibrium constants for methane developed in an earlier paper. INTRODUCTION A series of papers have been written on gas hydrates, giving temperatures and pressures at which hydrates would form.2. 3, 4. 5, 6. 9. 12, 13, 15 Vapor-solid equilibrium constants have been developed for methane, ethane, propane and iso-butane&apos; by which it is possible to compute for a specific gas mixture the temperature and pressure at which hydrates will form. Carbon dioxide is present in many natural gases in concentrations usually from 0.1 to 2.0 per cent. It also forms a gas hydrate with water and presumably enters the solid solution when present with a natural gas which is forming a hydrate. The equilibrium constant giving the ratio of the concentration of carbon dioxide in the gas phase to the concentration in the solid phase is required for including the effect of the carbon dioxide when computing the conditions for hydrate formation. Direct determination of the concentration of carbon dioxide in solid hydrate requires a difficult separation to be made. Therefore, this research resorted to the measurement of the temperature and pressure at which specific mixtures of methane and carbon diox- ide would form hydrates. From the equilibrium constants previously mentioned for methane, it is possible to compute the equilibrium constant for carbon dioxide, without measurement of the composition of the solid phase. Fig. 1 shows the conditions at which methane and carbon dioxide form hydrates. The methane curve FG extents to some high pressure while the carbon dioxide curve AB intersects the vapor-liquid water-liquid carbon dioxide

Jan 1, 1949

By H. M. Chance

The present value of most coal properties resides largely in the cod remaining to be mined, which thus constitutes the most important asset. The object of this paper is to discuss methods commonly used in computing the value of minable coal. To distinguish clearly between such coal values and the values of other property, the several kinds of property values should be divided into classes; so as to avoid the unintentional omission of items of importance. Value op Coal Reserves Judicial decisions prescribe, and appraisers commonly accept, current sales value as the preferred means for determining the value of transferable property. With few exceptions a property is worth the sum that can be realized from its sale by a willing seller to a willing buyer, a sale in which compulsion urges neither party, and between whom there is no community of interest to fix a value; or it is worth at least as much as a responsible buyer will offer for it. Actual sales of like property or bids from responsible buyers for the property, or for substantially like property, are the best established methods for determining values. Only in the absence of such sales or bids can valuations by other methods be entertained, and only for reasons of weight can sales values be set aside. Valuation Based on Royalties Sales of coal in the ground, as customarily carried out through lease under royalty agreements, are therefore the most trustworthy means available for determining the value of coal reserves. The constantly rising value of high-grade coal in the United States can most readily be shown by the increasing royalties per ton that can be obtained for such coals under leasehold. The rising value of land containing such coal can also, of course, be proven by the price at which such properties are actually sold as compared with prices obtainable for lands containing coal of the same grade in the past. It is exceedingly difficult, however, to establish values by the prices paid for coal

Jan 1, 1927

By Alvin Kaufrnan

This chapter will deal with the policy issues relating to mineral land disposal. The first portion of the chapter will discuss in general terms the legal systems utilized in disposing of mineral rights and the major problems encountered; the second section will comprise an analysis of the policy alternatives with emphasis on the pricing aspects. In this section, we are not attempting to provide a legal text, but simply to outline very briefly and sketchily the details of the systems. More detailed information can be obtained by contacting the appropriate governmental agency for specific information. Mining laws throughout the world are based on two major legal groupings: English Common Law and the Civil Law. These basic systems are often modified by Islamic Law and by negotiated -mixtures of these. Under English Common Law, which is embraced by the United States, Canada, and many of the members of the British Commonwealth of Nations, individuals can hold property and can extract minerals from it. The owner can dispose of minerals as he sees fit, either through contract, deed, or whatever other system is appropriate. CIVIL LAW Under Civil Law (also known as Regalian Law), mineral ownership is normally placed in the state, regardless of who owns the surface. This legal system applies in most European countries and their former colonies. It is derived from Roman law. The mineral deposits, thus, are worked under concessions. Most countries use a negotiated concession system and sometimes a combination of negotiation and competitive leasing. The negotiated system has advantages as well as disadvantages for both government and industry. In a system where the government administratively determines who is to get what, the concessions are normally large. Frequently they range up to several millions of acres and involve a considerable investment on the part of the concessionaire. There is no duplication of effort on the part of producers to obtain information, since a single concessionaire controls a given area. Consequently, less money is spent in toto because several prospective operators are not required to seek the same information. The system also has the advantage to the industry of permitting the concessionaire to select and retain the best producting area. Thus, major developmental expenditures are made on the production unit only, with a resulting reduction in the risk factor. The large initial size of the concession also minimizes the possibility of expending a large bonus payment for a barren property. The major governmental advantage of a concession is its flexibility in accomplishing other national objectives. For example, a lease could be negotiated at less than fair market value, but requiring substantial de-

Jan 1, 1976