Search Documents

By K. A. Natarajan, I. Iwasaki

The effect of poisoning on the behavior of platinum electrodes in redox potential measurements in metallurgical systems was studied in the presence of such inorganic surfactants as cyanide and sulfide and such organic surfactants as dodecylammonium acetate, trimethyldodecylammonium chloride, potassium ethyl xanthate, and potassium diethyl dithiophosphate (Aerofloat®). These chemical species represent, more or less, typical constituents encountered in leaching, flotation, and sewage treatment systems. Triangular wave voltammetry was used as the experimental technique to study the nature of poisoned surfaces. Among the species studied hydrogen sulfide and dodecylamine were found to form a resistant surface film affecting charge transfer. Platinum electrodes appeared to have a weaker tendency to adsorb sulfide species in alkaline pH ranges, while cyanide, xanthate, and dithiophosphate affected the normal electrode behavior differently. Possible methods of reactivation of a poisoned electrode by mechanical cleaning are suggested.

Jan 1, 1974

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a previous paper.1 The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques.

Jan 12, 1953

By C. R. Sundeen, C. W. Nicolson, J. D. McAuliffe, C. A. Campbell, P. D. Pearson

SHAFT SINKING SYMPOSIUM is a weighty term that could mean any number of things. However, in, this case it has been possible to utilize the transcription of the Annual Meeting Session of the same title and present it in much the same manner as the experts on the panel presented it to their audience Wednesday afternoon, February 18, 1953, at the Los Angeles Statler Hotel.

Jan 8, 1953

By Om P. Pande, Larry S. Diaz

Modern mineral processing plants could not operate efficiently, or even exist, without instruments which indicate, record, control, and in some cases anticipate the many changes that occur in a process. Even in plants which are operated manually, instruments are used to tell the operator when he should turn a valve or press a handswitch. Accordingly, all mineral processing plant engineering and construction projects must give careful consideration to this area of design activity.

Jan 1, 1978

By McAuliffe, Eugene

THE TERM "engineer" has been defined in many ways by many men broadly speaking the statement that "an engineer is one versed in or practicing any brar1c.h of engineering" is sufficient. A rather close relation exists between the sciences of surgery and engineering. A successful surgeon must have the capacity to perform the most delicate work, under extremely circumscribed conditions. This portion of his education is purely mechanical and although marvellous in itself, it must remain secondary to that greater possession, a thorough knowledge of human anatomy coupled with a comprehensive understanding of human psychology. In sub- stance, the surgeon must not only know how to operate but what is more important, he must be able to decide when, if ever, the operation should be undertaken.

Jan 1, 1932

By H. Merton Ruth

THE northern anthracite fields, although facing the same economic problems as the southern fields, are confronted with the additional problem of fast dwindling reserves of anthracite which can be conventionally and economically won. The mining of coal which remains in thin beds and the recovery of pillars from areas heretofore considered unrecoverable, either by reason of cost or surface restriction, pose problems of increasing importance to the economic life of the northern field operations. Successful approaches have been made to this problem and other work is being performed that holds promise. There exists in the northern anthracite field millions of tons of solid coal, the recovery of which has not been too successful due to the following inherent operating faults: inability to concentrate producing areas, the great quantities of rock to be cut and handled, lack of consideration of proper sequence and speed of second mining, and the continued use of the mine car as the basis of payment. A mining system that has successfully solved these major problems has been in operation in the Scranton area since 1944. Over 1% million tons have been produced from veins varying from 3 to 4% ft thick by this method, which is known as the multiple panel-triangular system-conveyor mining.

Jan 7, 1950

By J. E. Spurr

CONTENTS. [ ] I. INTRODUCTION. The region here discussed is that part of western Nevada in which, during the last few years, discoveries of rich gold- and

Jan 1, 1913

By F. E. Wood

This paper is written primarily as a discussion of Dr. W. P. Hase-man's paper on "A Theory of Well Spacing"' and presents briefly the production records, and intensity and rate of development in a large portion of the two principal producing sands in the Salt Creek field, Wyoming. The study includes 1350 wells, 160,000,000 bbl. production, well spacings varying from two to seven wells per 40 acres and early and late development. The general conclusions to be derived from this study are: 1. It is impossible to formulate a mathematical rule to apply to well spacing in the Salt Creek field. 2. Each tract is a separate problem. 3. Tracts first drilled produce the most oil, with many exceptions. 4. Initial production is not a reliable index to the relationship between past, current, or future production. 5. Wells which have produced the most oil in the past are not necessarily yielding the greatest current production nor will they yield the greatest future production. In fact, wells which have yielded the greatest past production will, in at least one-half the cases, make less oil currently or in the future than wells which have produced a smaller quantity of oil in the past. 6. The following is a safe rule to apply in well spacing in the Salt Creek field: (a) If the drilling of an additional well on a tract results in a sustained increased production, with prospects of making a profit, the tract is not overdeveloped and additional wells might be drilled. (b) If the drilling of an additional well does not effect a sustained increase in the production of a tract, the tract is fully developed. Second Wall Creek Sand The Second Wall Creek sand, covering 20,000 producing acres, is the principal producing horizon in the Salt Creek field; 1610 wells are producing at this time from this sand. This paper deals with hut a portion of the entire field including 10,680 of the more productive acres,

Jan 1, 1930

By William Fink

ALTHOUGH age-hardening in an aluminum-base alloy containing magnesium was observed by Alfred Wilm1 as early as 1911, it was not until 1919 that a theory of the mechanism of age-hardening was proposed. Merica, Waltenberg and Scott,2 studying the age-hardening character-istics of Duralumin at the National Bureau of Standards, came to the conclusion that age-hardening of this alloy is caused by the precipitation of CuAl2, which is less soluble at the aging temperature than at the solu¬tion heat-treating temperature. It was postulated that the initially precipitated particles were of fine colloidal dimensions but that they gradually grew in size. Maximum hardness was assumed to be attained when the particles reached a critical size. This theory was at first received skeptically, since it was a widely accepted view at that time that the solid solution state should represent the hardest state of an alloy. Shortly thereafter, Jeffries and Archer proposed their well-known "slip interference theory."3 They suggested that age-hardening was accomplished by the precipitated particles acting as keys interfering with slip along crystallographic glide planes. They showed that this mechanical theory led directly to the assumption that maximum harden-ing would be produced by particles of a critical size, which they suggested would have a diameter approximately 10 times that of the aluminum atom. This contribution amplified and explained so rationally the age-hardening theory of Merica, Waltenberg and Scott that wide accept-ance resulted.

Jan 1, 1939

By L. C. Uren, J. Domerco

That the diameter of a well through the oil-producing formation has an important influence on its rate of production is a principle accepted by many petroleum technologists. Knowledge of this principle extends back at least to the time when Slichter and King1 confirmed it in a study of the dynamics of flow of water through porous strata into wells. More recently, the senior author2 and his associates3 have produced qualitative experimental data confirming the principle as applied to drainage of expanding oil and gas mixtures, and suggesting that wells of large diameter, or wells having cavities about them within the reservoir rock, enjoy a material advantage in competition with wells of ordinary diameter. Apparently, however, no one has produced experimental data designed to indicate quantitatively the advantages that wells of large diameter possess in comparison with wells of normal diameter producing under comparable conditions. This paper reviews some preliminary experimental results of this kind, together with some conclusions and speculations based thereon, which further emphasize the importance of well diameter as a factor in determining the efficiency of oil recovery. Theoretical Aspects of Radial Flow of Fluids into Wells It is well understood that in a reservoir rock of uniform thickness and permeability oil and gas flow toward the wells along radial lines. The cross-section of the reservoir rock through which the fluids must move becomes ever smaller as the wall of the well is approached. The velocity of flow must therefore correspondingly increase, an effect that is accentuated by the rapid increase in volume of the fluid due to release

Jan 1, 1935

By Oliver Halston

THIS paper reports the results of the use of salt in some research work carried on during the past 3 years at the Salt Lake City Station of the Bureau of Mines, which is quartered in the University of Utah, whose Metallurgical Research Department cooperates with the Bureau. Only the work involving the use of salt is described. The authors wish equal credit given to J. F. Cullen, C. L. Larson, C. Y. Proutz, C. E. Sims, H. C. Neeld, R. W. Johnson, F. G. Moses, N. C. Christensen, and G. H. Wigton, who have all in some way contributed toward the success of this work. Lead Metallturgy Popularly Supposed to be Without Problems In bead metallurgy it is difficult at first to find metallurgical problems, as the prevailing conception has been that bead is so easily concentrated in its various ores and so easily reduced to its metallic form that the only progress possible is that involved in cheapening methods of mining and of reduction. Most of the problems usually considered are of minor nature and do not involve radical metallurgical changes. During the 3 years of work of the Salt Lake Station, the following classification of problems in the metallurgy of bend has been made: Those involving Oxidized Ores. 1. Ores containing only bead. s. Ores containing bead and silver or gold. 3. Ores containing bead and zinc, with or without silver. Sulphide Ores. 1. Ores of pyrite carrying some bead. 2. Ores of complex zinc-bead-iron sulphides. 3. Complex sulphides containing in addition precious metals.

Jan 8, 1917

By Leroy Palmer

ALL the domestic. production of magnesite during 1925 came from two states, California and Washington. Of a total of 120,660 tons of crude ore, 64,600 tons, or 54 per cent., were produced in California.1 Of .this quantity California produced about 99 per cent. of the caustic calcined, but only 10 per cent. of the dead-burned. The largest producer was C. S. Maltby, of San Francisco, who operated the Red Mountain mine, in Santa Clara County, and the Sampson mine, in San Benito County, under lease. These two mines have been studied by the author, and offer interesting comparisons as to mining and treatment methods and final products. GEOLOGY The general geology of the magnesite deposits of California has been described by Hess,2 Bain3 and others,4 and although a detailed discussion is not necessary here, a brief summary will assist in understanding mining conditions. California magnesite, when comparatively pure, is usually a white, fine-grained rock, with a conchoidal fracture, occurring in veins and lense-like masses in serpentine. The veins vary considerably in width, and usually occur in a series of more or less parallel veins intersected by other series or systems of veins, probably following original or secondary fissures in the enclosing serpentine. The most generally accepted theory of origin is that the magnesite was formed by the action of surface waters charged with C02 percolating downward through fissures and changing the magnesium silicates of the serpentine into magnesium carbonate.

Jan 1, 1927

By R. A. Meussner, R. T. DeHoff, F. N. Rhines

ZINC diffuses through copper more rapidly than does tin. Accordingly, when a ternary diffusion couple is made, by bringing an 0 copper-zinc brass into contact with an a copper-tin bronze at fixed high temperature, it is to be expected that zinc will diffuse into the bronze faster than tin diffuses into the brass. Adjacent to the brass side of the couple the total alloy content (zinc plus tin) should diminish, therefore, while next to the bronze side the alloy content should increase. Since the path of compo- sition change must be continuous, in a single-phased alloy, it should follow a curved and, in general, an S-shaped course. The realization of this prediction is demonstrated in Fig. 1, where the composition paths of two ternary diffusion couples are plotted on the appropriate isotherm of the copper-tin-zinc phase diagram. The diffusion couples were both made from a binary copper-tin alloy analyzing 5.0 pct tin placed against binary copper-zinc alloys analyzing 18.9 and 29.3 pct Zn, respectively. These alloys were produced from electrolytic grades of copper and zinc and a pure grade of straits tin, melted under borax in clay-graphite crucibles and cast in a vertical iron mold. Cylindrical pieces 1 in. in diam and 1 % in. long were machined from the casting and were faced by metallographic polishing to good matching end surfaces. Pairs of the cylindrical pieces were held

Jan 1, 1959

By Walter H. Voskuil

Illinois supplies coal to seven states in the Upper Mississippi Valley —Illinois, Missouri, Iowa, Minnesota, Wisconsin, and portions of the Dakotas, Nebraska and Kansas. In this same area are marketed large quantities of coal from West Virginia, Kentucky, Pennsylvania, and elsewhere; fuel oil from the crude petroleum supplies of the Mid-Continent fields, and natural gas from Louisiana, Kansas and the Texas Panhandle. The boundaries of this "Illinois coal-market area" are determined by competition from other coal fields and from other forms of fuel. Within the area so described 90 per cent of Illinois coal is marketed. Thus in the Southwest, an abundance of fuel-oil supplies and natural gas dominates the market almost to the exclusion of coal. The westward movement of Illinois coal in Kansas, Nebraska and the Dakotas is met by an eastward flow of high-grade coals from Colorado, Wyoming and Montana. In the lake-shore counties of Minnesota and Wisconsin, the market is dominated by Appalachian coals, cheaply carried over the Great Lakes and reaching the ports of Lake Michigan and at the head of Lake Superior. Illinois coals find their largest market in the southern and western sections of these two lake states. Only small quantities of Illinois coals are shipped east of the state line. This market area is occupied entirely by the neighboring coal fields of Indiana and the Appalachian coal fields in Ohio, West Virginia, Kentucky and Pennsylvania. Illinois Coal-makket Area , With these factors in mind, the map of the Illinois coal-market area may be drawn. Within this boundary is the area that is logically and economically served by Illinois coal. However, this area is by no means exclusively dependent upon coal from Illinois mines. The preponderance. of Appalachian coal in Wisconsin and Minnesota has been mentioned. Appalachian coal, also, moves in large tonnages into Illinois itself, particularly the Chicago district. The Iowa and Missouri local coals share the market with imported coal from Illinois; throughout the market area, fuel oil and natural gas are important factors in the total energy supply.

Jan 1, 1936

By Walter H. Voskuil

Illinois supplies coal to seven states in the Upper Mississippi Valley —Illinois, Missouri, Iowa, Minnesota, Wisconsin, and portions of the Dakotas, Nebraska and Kansas. In this same area are marketed large quantities of coal from West Virginia, Kentucky, Pennsylvania, and elsewhere; fuel oil from the crude petroleum supplies of the Mid-Continent fields, and natural gas from Louisiana, Kansas and the Texas Panhandle. The boundaries of this "Illinois coal-market area" are determined by competition from other coal fields and from other forms of fuel. Within the area so described 90 per cent of Illinois coal is marketed. Thus in the Southwest, an abundance of fuel-oil supplies and natural gas dominates the market almost to the exclusion of coal. The westward movement of Illinois coal in Kansas, Nebraska and the Dakotas is met by an eastward flow of high-grade coals from Colorado, Wyoming and Montana. In the lake-shore counties of Minnesota and Wisconsin, the market is dominated by Appalachian coals, cheaply carried over the Great Lakes and reaching the ports of Lake Michigan and at the head of Lake Superior. Illinois coals find their largest market in the southern and western sections of these two lake states. Only small quantities of Illinois coals are shipped east of the state line. This market area is occupied entirely by the neighboring coal fields of Indiana and the Appalachian coal fields in Ohio, West Virginia, Kentucky and Pennsylvania. Illinois Coal-makket Area , With these factors in mind, the map of the Illinois coal-market area may be drawn. Within this boundary is the area that is logically and economically served by Illinois coal. However, this area is by no means exclusively dependent upon coal from Illinois mines. The preponderance. of Appalachian coal in Wisconsin and Minnesota has been mentioned. Appalachian coal, also, moves in large tonnages into Illinois itself, particularly the Chicago district. The Iowa and Missouri local coals share the market with imported coal from Illinois; throughout the market area, fuel oil and natural gas are important factors in the total energy supply.

Jan 1, 1936

By Morris Cohen

WITHIN the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;1 and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, he concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot2 formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrence of precipitation. The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. ? The general precipitation occurs at a

Jan 1, 1938

By H. D. Wilde

At the Sugarland and Raccoon Bend fields in the Gulf Coast area, all wells are drilled with rotary tools and the casing is always set in cement that is placed by the circulation method. After the cement is set, the rotary mud that fills the hole is not withdrawn or bailed out; consequently, it is not customary to give the cementing job a direct test either by putting pressure on the hole to see whether the cement will hold or by observing whether an effective water shut-off is secured. About three years ago, this company started the practice of coring the cement left in the bottom of the casing and examining the core thus secured. If the core was hard and strong, the cementing job was judged a success but if the core was incoherent, soft, and crumbly, the job was considered a failure. Of course, there were intermediate types of cores and it was not always a simple matter from this examination to decide whether the job was a success or failure. After about two years, a summary of the core examinations that had been made indicated that of cementing jobs made at depths of 1000 ft. or less, 60 per cent.. were failures; of those between 1000 and 2000 ft., 80 per cent. were failures, and of those between 3000 to 6200 ft., 100 per cent. were failures. This sta,rtling table emphasized the need of the study of the conditions under which the wells were cemented and of adopting means to reduce the percentage of failures. In addition to these core tests, two wells gave direct evidence that the cementing jobs were not always successful. In one, a four-year-old well at Goose Creek, the casing was perforated, and when fluid was circulated some of the old cement wss brought to the surface. Most of it was powdery and the few chunks that were brought up were soft and crumbly. The other was a well at Raccoon Bend which during a blow-out brought a number of chalky, soft and crumbly pieces of cement to the surface. Suggested Explanations of Cementing Failures Efforts were made at once to explain the causes of these cementing failures. As all of the cements used were of a high grade and gave

Jan 1, 1930

By Pope Yeatman

In my experience, perhaps the most interesting problems came up during the testing, prospecting, developing and equipping of the Chuquicamata and Braden Copper Mines in Chile, and it is proposed in this article to give as briefly as possible what some of those problems were, their solutions, and the decisions made as to the different methods to be employed. The romance of mining is still a great lure to the young man who is making a choice of a profession to follow. The thought of travel to strange and out-of-the-way places, the glamor of pioneer life, the excitement of discovery, the constructive work of building something, entirely "from the grass roots up," or of reconstructing a played-out property and making a success of it-all of these phases have a strong appeal and often influence the young man in the choice of mining as a profession. That great engineer, Col. Seeley Wintersmith Mudd, whom we are endeavoring to honor, while having too much common sense to have been materially influenced by the romance of mining, certainly experienced all of the

Jan 1, 1932

By Frank C. Appleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaS042H20) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal con- stituents of evaporite deposits, and when pure, has the following composition: [ ] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product.

Jan 1, 1975

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.' This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943