Search Documents

By John Peperakis, James Quigley

IN 1950 Kaiser Steel Corp. acquired control of the Utah Fuel Co., a pioneer Utah coal concern owning large reserves of high volatile coking coal near Sunnyside, Utah, and large reserves of coal elsewhere in Utah and Colorado. Kaiser Steel later disposed of the noncoking quality reserves included in the property and over the past six years has developed a group of three fully modernized mines and a central preparation plant at Sunnyside. This plant is geared to furnish 1.6 million tons per year of low ash coking coal to the byproduct coke ovens at its steel plant at Fontana, Calif., and to its beehive oven coking plant at Sunnyside. General Problems: Topographic and physical conditions under which Utah coals are found differ from those in most bituminous coal districts of the eastern and central states. Utah coal seams lie under deeper cover, generally at steeper pitches; consider- able distances are burned along the outcrop and back from the surface of the outcrop. Usually the coal seams lie high up on escarpments, accessible only through deep narrow canyons or long rock tunnels and tramways. The topography at Sunnyside is particularly rough, with great changes in cover over the coal in relatively short horizontal distances. This is due to the cliff-making sandstones of the cretaceous Mesa Verde group, the coal-bearing measures being in the Blackhawk formation. The thick massive Castle Gate sandstone of the Prince River formation overlies the coal-bearing rocks and is suspected to be the chief cause of roof control problems.

Jan 10, 1957

By K. Unrug, G. Herget, A. Smith

SUMMARY Statistics on roof falls indicate that the cost of just removing the unwanted waste from roof falls in US coal mines amounts to about $20 M per year. Almost 40 percent of fatal accidents occur under permanently supported roofs, indicating that the assessment of roof stability is still a very difficult task. In an effort to obtain a better understanding of roof fall occurrences, rock strength and ground stresses were determined in the roof of one mine each in Western Kentucky, northern West Virginia, and Eastern Kentucky. Triaxial ground stress determinations clearly show that horizontal stresses were higher than vertical stresses, and that maximum stresses in the horizontal plane were concentrated between the NE-SW to E-W direction, with the exception of the Eastern Kentucky site which was above the drainage. Magnitudes of stress components may vary considerably in one drlll hole. Strength tests of roof strata materials were done on core samples. Mapping of roof falls showed that the geometry of an opening or maximum span were not the overruling factor because in the same general area, a roof fall was observed in a room (entry) which connected two stable four-way intersections. It should be noted that, in very wet areas, the roof can break up to the bed where water is carried, and a very low ratio between extent of roof fall to height of roof, fall is observed. Geometry is, however, a contributing factor because nearly 70 percent of roof falls are intersection falls. The frequency of fractures parallel to bedding in failed roof strata is much higher than that observed in the original strata, indicating a significant amount of working in the roof before failure.

Jan 1, 1984

The first discovery of gold in Montana is credited to François Finlay, a half-breed, from the Red River country, in Canada; he went to California during the early days and learned there how to wash the gold from placer deposits; then, on his return, he crossed Montana and found gold on the western slope of the Rocky Mountains, on Gold creek, a minor tributary of the Hell Gate river, in what is now Deer Lodge county. That was in 1852.* Finlay did not find enough gold to induce him to continue at work, but six years later a group of miners, led by the brothers James Stuart and Granville Stuart prospected on this same creek, obtaining about ten cents to the pan. They, however, were harassed by the Blackfeet Indians, and they were also handicapped by lack of proper tools; so they too desisted from further operations. Two years later, in 1860, Henry Thomas started to work on Gold creek with three sluice-boxes hewn out of green timber that he cut on the spot. With this simple apparatus he won from $1.50 to $2.00 per day. This may be considered the fist instance of systematic mining in Montana. Meanwhile the Stuarts went to Fort Bridger, in southwestern Wyoming, where they remained as traders until 1861, when, again lured by the gleam of gold, they returned to the valley of the Deer Lodge and resumed prospecting, using 10 sluice-boxes that were brought from Walla Walla, in Washington, 425 miles distant. In the summer of 1862 they were joined by many others, chiefly from Colorado, in consequence of an exchange of

Jan 1, 1932

By C. H. Li, R. J. Stokes, T. L. Johnston

A portion of the Ni3Cr-Ni3Al phase dzagram has been investigated, including the precipitation of 1 (Ni3Al) as well as the existence of ordered Y (Ni matrix), Extensive metallographic studies by electron microscopy have been carried out and X-ray diffraction diagrams have been taken at both elevated and ambient temperatures, No long-range ordering of the phase was found above 893°C (1639°F) in the compositional range investigated. The high rate of formation of the ordered ?1 phase upon quenching has been confirmed, a phenomenon which up to the present Lime has retarded the understanding of this phase diagram, Specimens with controlled amounts of ?1 exhibited up to a six-fold improvement in yield and creep strength compared with single-phase Ni-Cv-A1 alloys. MOST of the important high nickel heat-resistant alloys are related to the nickel-chromium-aluminum system. One of the important functions of the aluminum, often accompanied by titanium, is to produce a precipitate of the very fine ?1 phase (Ni3A1, X) where X may be Ti, Cr, or other elements. A number of investigators1-" have demonstrate the presence of y' in these alloys but most of their materials contained large amounts of other elements resulting in appreciable amounts of con- fusing phases such as carbides. Further clouding of the precise role of y' has been the suspected existence of an ordering reaction in the y matrix itself, ro-3,12-17 It appeared from these investigations that aluminum in Ni-Cr alloys would raise the ordering temperature of the matrix from 540°C at NisCr to 1300°C at Ni,Al. In support of this possibility, the matrix phase in the parallel Ni-Fe-A1 system is ordered to very high temperatures.1 OBJECTIVES OF THIS RESEARCH From this survey of the literature it appeared desirable to conduct an investigation of the simple Ni-Cr-A1 system using the alloys of the highest available purity to avoid the complication of foreign phases and thereby isolate the structures in the Ni-Cr-A1 system. Procedures were developed to study ? - ?o and ? - ?1 equilibria. Preliminary mechanical tests at elevated temperatures were also conducted.

Jan 1, 1962

By W. H. Newhouse

DURING the past few years the writer has been impressed by the close relation of many epigenetic orebodies with anticlinal structures. In the literature on ore deposits there is occasional mention that an oreshoot or district is on an anticline, but in most of the descriptions no weight or significance is attached to the relation, and usually the fact is concealed in a mass of structural detail. A few writers have stressed the relationship in a few districts or on a certain type of deposit. Church, Spurr, Butler, Stahl and Schuette have called attention to certain features, but the general extent of such a correlation has not been made known in any publication that the author has seen. A recent article1 on the localization of ore deposits, by well-known geologists, does not consider this common association. The author has seen in the field a number of the structural features described, and in addition has made a fairly complete review of the literature. This paper presents enough of the examples found to show the frequency of the relation to anticlines, and since only a few deposits on synclines are known, all of these of any importance of which the writer knows are mentioned. With certain qualifications which are discussed later, epigenetic ore deposits of replacement or vein type are mostly found where local upwarps of the earth's crust have taken place. Where formations antedating the ore deposits are present in the proper attitude to demonstrate vertical warping (i. e., more or less horizontal beds) the structural feature on which a mineral district, or mineralized area is located is almost always anticlinal, or domelike in nature. Some or even most of the ore deposits in a given district may be on the flanks of the upwarp, but few major districts are located definitely on downwarped areas. Synclinal basins within certain limits of size appear to be unfavorable to the type of fracturing that admits ore-bearing solutions.

Jan 1, 1931

By Bernard York

Mine opening stability was investigated by loading model openings to failure. Eight-inch plaster blocks were cast with small uniform section openings passing through the centers. After curing, the models were jacketed and loaded hydrostatically in a closed vessel. Opening size, shape, and orientation were varied to determine how these factors influence opening stability.

Jan 7, 1953

By T. R. Graham, R. G. Feustel, J. R. Long, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

The comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined. These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their- physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. Composition and Fabrication of Alloys The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys mill be referred to hereafter by their norninal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedurzs calculated to produce sheet $i6 in. thick, cold-reduced by 20, qo, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from 700' to r500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By P. T. Stroup

Jan 1, 1964

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933

By L. F. Wright

Operations of these two mining companies have some superficial similarities-geographical location, production rates, comparatively large ore reserves; but any critical comparison of mining and milling procedures or of economics must take into account the striking differences in geological environment and mineralogy of the respective ore deposits. The properties are only about 20 miles apart on an upland surface of moderate relief (part of the Interior Plateau of central B. C.) which occupies an area east of Thompson River between the towns of Ashcroft and Merritt. Being in the "dry belt" of British Columbia, water conservation is necessary at both operations.

Jan 12, 1963

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

By F. S. McNicholas

In the first big blast at Climax, a "loop back" (three-wire system) was used (Fig, I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1940

By E. H. Sellards

Phosphate rock like other mineral substances is found in nature in varying degrees of purity.

Jan 1, 1915

By F. J. Arriagada

A conventional technique used to process auriferous sulfidic concentrates involves a pre-leach oxidative-roast step. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. Surface analytical techniques such as scanning electron microscopy and BET gas adsorption have been utilized to determine quantitatively the structural morphology of calcined pyrite and arsenopyrite samples in the range of 450 to 750 °C under an oxidizing atmosphere. In the case of. pyrite calcines a highly porous hematite product was found below 500 °C; at higher temperatures, a coarser oxide network , was observed. The surface area of these calcines was found to decrease sharply with increase in temperature. In contrast, the surface area of arsenopyrite calcines was found to follow a bimodal-type behavior with roasting temperature with maxima at 500 and 625 °C. In the case of pyritelarsenopyrite mixtures, the surface area was observed to increase dramatically as the content of pyrite increased. The appearance of pyrrhotite as an intermediate phase in the oxidation reactions is postulated to have important structural implications.

Jan 1, 1984

By M. F. Smith

BELOW the nose of the bainitic C curves in isothermal transformation diagrams, the rate of the austenite-to-bainite transformation usually decreases with decreasing temperature. However, in some steels and iron-carbon alloys, there is a noticeable acceleration in the initial reaction rate at temperatures just above Ms. Such speeding-up of the bainitic transformation would be understandable at temperatures just below Ms because of the catalytic effect of the martensite formed,' but the reversal in isothermal kinetics just above Ms seems quite anomalous. This behavior was observed by Howard and Cohen' in a 1.35 pct C steel and, on the basis of metallo-graphic examination, it was attributed to the formation of a thin plate-like product not belonging in the bainitic sequence. More recently, schaaber2 found two-stage reactions occurring in the vicinity of Ms in a number of steels, and suggested that the first stage might be the isothermal formation of marten-site, preceding the isothermal formation of bainite in the second stage. A decrease in the bainitic incu-

Jan 1, 1960

By P. C. Kapur

A principal first-order and a minor summation term contribute to the solution to the discretized batch-grinding equation when formulated in cumulative retained mode. Depending on the inter relations hips between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The irn-plications and advantages of the reduced grinding equations are briefly discussed. In many instances, the trajectory of the particle-size distribution in a batch mill may be extracted from a set of particle mass balance equations as follows

Jan 1, 1971

By L. M. Cathles, H. R. Spedden, E. E. Malouf

Fluid flow through an igneous rock formation will occur mainly through fractures. A non-diffusing or slowly diffusing tracer (such as .5µ silica spheres identifiable under electron microscope) will arrive at a monitor well when enough fluid has been injected to displace the volume of water in the flow fractures between the injection and monitor wells. A rapidly diffusing tracer (such as NaC1)-will diffuse into the matrix blocks and so a volume of tracer nearly equal to the total fluid volume contained in the rock formation between injection and monitor wells must be injected before significant diffusing tracer arrival will be noted. The flow fracture porosity is typically one hundred times smaller than the total porosity of an igneous formation. The shift between diffusing and non diffusing tracer arrivals, together with the diffusional characteristics of the tracers, can define the diffusional accessibility of the matrix blocks of an igneous formation. A field test of these concepts and the problems encountered will be described.

Jan 1, 1974

By F. J. Williams

BARITE, naturally occurring barium sulphate, is the chief barium mineral that is produced commercially. Barite is also called "barytes," "heavy spar," sometimes "baryta" and, locally in Missouri, "tiff." Pure barite is white, opaque to transparent. It crystallizes in the orthorhombic system, frequently with twinning. Impurities cause a wide variation in color, commonly buff, gray and white with irregular reddish iron stains. Less frequently found are shades of yellow, green, blue, brown, and black. The rock is brittle and breaks with an uneven fracture, although specimens from some of the residual deposits, particularly in Missouri, appear to have a cleavage due to the separation of the different layers of deposition. The hardness varies from 2.5 to 3.5 on Mohs' scale and different localities are said to produce either "hard" or "soft" barite. This generally refers to the ease of grinding of the product. The specific gravity of pure barite is 4.5 and this will vary downward, depending on the impurities present. The mineral has a white streak and a pearly to vitreous or sometimes stony luster. Pure barite contains 65.7 pct BaO and 34.3 pct SO3. Witherite, native barium carbonate, is not mined in the United States at the present time although a number of occurrences have been reported. A small quantity of witherite has been removed from a mine at El Portal, California, but the area high in witherite was small and soon depleted. The bulk of the deposit is predominantly barite. Great Britain is the world source of witherite and small quantities are imported into the United States. DISTRIBUTION OF DEPOSITS Occurrence of barite is widespread; it has been reported on all the continents and in all the major countries of the world. Deposits vary from those containing millions of tons down to scattered rock fragments

Jan 1, 1949

By John Gross

The study of the energy used in crushing operations has advanced from a period of perplexing confusion to one of greater clarity. Only within the last few years has any true conception of the work in crushing been possible, owing to the chaotic state of theoretical knowledge. For some 20 years a controversy existed between those advocating the Rittinger law and those advocating the Kick law. The Kick law now appears to be definitely out of the picture, and crushing efficiency may be based confidently on the Rittinger theory. There also seems to be a generally crystallized conception as to the meaning and nature of sub-sieve material. There is needed a simple, direct method for determining surface on a crushed ore product, and also a simple and accepted method for size determination on minus 400-mesh material. The Crushing Law The Rittinger(l)‡ theory of crushing was advanced in 1867 and the Kick(3) theory in 1885. While the Rittinger theory might have been accepted without much question and actually had been accepted by many investigators, a serious doubt as to its validity was raised by Stadler(10) who upon purely theoretical grounds proclaimed the Kick "law" as the true law of crushing. According to Rittinger the energy required in successive steps in reduction increases geometrically, while according to Kick the energy increases arithmetically. These "laws" therefore are at variance, and the establishment of the true law was recognized as of first importance. Many simple experiments have been made to demonstrate the application of the Rittinger theory to crushing, and it would seem that its simplicity should favor its acceptance. Experimental evidence, however, was not convincing, as no reliable data could be obtained on the finer material from a crushing or grinding operation. Gates,(13) Bell,(19)

Jan 1, 1935