Search Documents

By D. E. Pickett, E. G. Joe

In accordance with good industrial practice, Canadian metallic-ore concentration plants have always recycled a high proportion of process water to save reagents, save power, conserve water resources, and to protect the community water supplies, to give only a few reasons. In the last few years there has been awakened public concern for the environment and, consequently, government regulations have been added as additional reasons. Present recycling practices are summarized as a basis for improved plant design and operating procedures and for further research. In addition, an attempt is made to determine why plants do not recycle water in certain situations. Although not all Canadian mills are covered, the many examples given indicate the problems and the effort being made to solve them. Wherever available, the chemical quality of the water and the process requirements are indicated as well as the other parameters affecting water recycling at each operation.

Jan 1, 1975

By C. C. Clark, J. S. Iwanski

The purpose of this investigation was to study mi-crostructural changes that take place in a commercial nickel-chromium-iron alloy, such as Incoloy "901," over long periods of time at temperatures up to 13 50°F and to correlate such changes with creep-rupture properties. of the alloy. In the course of the investigation, some microstructural changes were observed which correspond to microstructural alterations found in previous studies of Inconel "X." Microstructural phases have been identified in both alloys with the aid of electron and X-ray diffraction and an electron probe microanalyzer. The materials used in this investigation were from commercial heats of the following chemical composition: Pct Cr Pct Ni Pct Mo Pct Fe Pct Cb Incoloy "901" 12.51 43.67 5.72 Bal. -Inconel "X" 14.61 73.44 - 6.61 1.02 Pct A1 Pct Ti Pct Mn Pct Si Pct C Incoloy "901" 0.10 2.46 0.46 0.24 0.05 Inconel "X" 0.70 2.43 0.51 0.36 0.04 Long-term creep-rupture tests were conducted on Incoloy "901" at temperatures of 1000°, 1200°1 and 1350°F. A summary of these results is shown in Table I along with the results of a long-term creep-rupture test conducted on Inconel "X" at 1500°F. The heat treatments given the specimens are also shown in Table I. When the creep-rupture results on Incoloy "901" are compared with shorter-tertn data, there is no evidence of any undue deterioration of the creep-rupture strength with time, nor is the elongation decreased more than would be expected from the influence of time alone. INCOLOY "901" PHASE IDENTIFICATION Microscopic examination of the Incoloy "901" specimens reveals a dark etching grain boundary constituent in the specimen which was under test for about 11,500 hr at 1000°F. This grain boundary constituent was seen to increase in size as the test temperature was increased to 1200" and 1350°F, Figs. 1, 2, and 3. Simultaneously, an acicular structure of definite crystallographic orientation appears within the grains of the 1350°F specimen, Fig. 3. Under examination with the electron microscope, a fine precipitate is observed in the 1200 °F specimen. Fig. 4. It becomes considerably larger in the 2850-hr 1350°F specimen, Fig. 5. In a few areas the precipitated particles have been replaced by, or transformed to, small needles or platelets. After 7380 hr at 1350°F, Figs. 3 and 6, the needles are much larger and have replaced nearly all of the fine precipitate. X-ray diffraction studies detected the presence of hexagonal Laves phase and hexagonal n phase (Ni,Ti) in the 1350°F specimens, Table 11. Only the Laves phase was detected by X-ray diffraction in the 1200°F specimen and none was detected in the 1000°F specimen. In this latter specimen, however, the small quantity of precipitate in the grain boundaries (presumed to be Laves phase) precludes its detection by X-ray diffraction. Composition of the hexagonal Laves phase is not yet known, although its diffraction

Jan 1, 1960

The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and out standing attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated: 1924 What is Steel? By Albert Sauveur.

Jan 1, 1934

By J. Kinkead, R. M. Sherman, E. M. Frizzel

A recent research study performed under US Bureau of Mines Contract No. J0199088 "Modular Irrigation Equipment for Reclaimed Strip Mined Lands" investigated the feasibility of irrigation as a reclamation tool in the arid and semi-arid regions of the Western United States. Review of mined land characteristics, evaluation of irrigation systems, and assistance from the mining industry resulted in the design of two strategies for the implementation of reclamation irrigation using solid set systems. It is not the intent of this paper to suggest the generalizations made on the basis of a six state area can extend to the design of an irrigation system for a specific mine site. The purpose is to present two irrigation strategies that may be implemented with solid set irrigation in this six state area. The reader should note that the following is the result of research and, therefore, original concepts were presented. The ultimate validity of these concepts will be determined by future field tests.

Jan 1, 1983

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern US and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales. This resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 67 Gm3 (423 billion bbl) of oil could be recovered by HYTORT processing of surface minable eastern US shales. Recently, American Syncrude Corp. and Southern Pacific Petroleum NL have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized.

Jan 1, 1986

By Warren K. Kourt

Many important discoveries of mineral deposits have been made as a result of routine exploration for oil and gas. Through the presentation of three hypothetical case histories, including cost data, the author shows how mineral evaluation can be performed during routine petroleum drilling operations and how mining companies and oil companies or oil operators can cooperate in such endeavors.

Jan 1, 1972

By R. E. Zimmerman, Shiou-Chuan Sun

An evaluation of the mechanism surrounding the froth flotation of coarse coal and mineral particles as a result of experiments conducted at The Pennsylvania State College. Maximum size ranges for both bituminous and anthracite coals were established as well as the factors affecting the floating of coarse particles.

Jan 5, 1950

By Harold A. Krueger

FACILITIES and mining operations of the National Lead Co., St. Louis Smelting and Refining Division, near Fredericktown, Mo., are situated in a famous mining area. Copper, lead, nickel, and cobalt have been mined here for more than 100 years, work having been started on a high sulphide copper outcrop in 1847.

Jan 8, 1953

By William Reynolds

THIS paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. FACE PREPARATION When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of complete-ness to which these impurities are removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miner is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation.

Jan 1, 1936

By J. Boldy

Discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage halo as a lithochemical pathfinder to blind ore. Its location, relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy was also a factor. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 110-m (360-ft) level.

Jan 1, 1985

By Ira B. Joralemon

INDIVIDUALS and small companies have discovered and brought into production the mining districts of the United States. Hardly an exception comes to mind, save for the disseminated copper properties and the great iron mines. In spite of this fine record that has made possible the industrial greatness of the country, mining by small companies and by individuals has become a vanishing phenomenon. In Nevada, the lair of rugged individualism, there are fewer operating mines and fewer miners than at any time since the 1860's. The situation in other states is nearly as desperate.

Jan 8, 1950

By J. K. Jeyapalan, A. P. S. Selvadurai

Plate loading tests which use surficial loading of a rock mass are employed quite extensively for the determination of in situ deformability characteristics of rock masses. The cable jacking method is essentially a surficial plate load test in which the test load is provided by reaction against a cable anchored at some depth below the rock surface. The results of the test are usually evaluated within the framework of the classical theory of elasticity to generate estimates for the bulk deformability properties of the rock mass. In the conventional evaluation of this test it is assumed that the test plate is rigid and that the embedded anchor load has no influence on the test plate settlement. The purpose of this paper is to examine the possible influences of the plate flexibility and the anchor load location on the effective settlement of the test plate. The variational estimates presented in the paper are valid for moderately flexible test plates which are characterized by a relative rigidity parameter Numerical results are developed in the form of correction factors that should be applied to the cable jacking results to arrive at the deformability characteristics of the tested rock mass.

Jan 1, 1982

By John A. Church

THE Lake Superior blast-furnaces probably represent the maximum economy of fuel possible in this country. They smelt an ore which is very rich and easily reducible, and as the small amount of gangue present is not all silica, but in part a silicate, the amount of limestone required is a minimum. The average yield of the ore treated at six furnaces was 63 per cent., and the average quantity of limestone 179 pounds per ton of pig. The fuel used is charcoal, so burned as to retain most of the combustible volatile part, which, before the utilization of furnace-gas, was burned away. With these conditions it is not surprising that the Lake Superior charcoal practice is extraordinary in almost every respect. In any scientific discussion of American furnace work, the establishments there will be found at the head of the list, and they work under conditions which are extremely favorable for careful study. The Bay Furnace, near Marquette, has the honor of carrying "the broom" for the largest daily make. With a capacity of 1908 cubic feet it has, for months together, produced 29 tons of pig, graded at

Jan 1, 1876

By Robert Forsyth

In working the Bessemer process, the bottom of the converter has always been a source of trouble and annoyance, and the subject of more experiments, probably, than any other part of the complex mechanism called a Bessemer plant. This will not appear remarkable when the duties this important piece of refractory material has to perform are taken into consideration. In the first place, by means of the tuyeres, it delivers at a high pressure the air necessary for the conversion of the bath of metal, and has then to resist the intense

By Richard P. Rothwell

REVOLING slime-tables with stationary sprays and oscillating brushes have for many years been a favorite apparatus used for working slimes in German dressing-works, often displacing Rittinger tables and the many variations of Cornish buddles. The difficulty of building these tables larger than 5 1/2 meters (17 feet) in diameter, increasing the cost and making them unwieldy, rendered it necessary also to concentrate the slimes in several operations, because the travel over so short a length of hearth would not suffice for close concentration. A preliminary sizing is effected in a system of spitzkasten. Herr C. Linkenbach, general manager of the Ems Lead and Silver Works, Germany, devised a buddle, in 1878, which has since worked well and found much favor in Germany, and has been in one instance copied here, at Colorado Springs, without any credit having been given to the original inventor. Linkenbach's plan has been to reverse the functions of the table and the washing apparatus of the old German revolving table. He makes the tables stationary and rotates the washing apparatus,, thus enabling him to save in power, and, within certain limits, to increase the dimensions of the table, without in any way affecting its durability or materially increasing its cost. In its earlier form, the buddle was single, and that type is still

Jan 1, 1883

By Robert Steinitz

SOFT iron parts for magnetic applications, particularly pole shoes, constitute a major portion of the ferrous products of powder metallurgy. The residual pores in pressed and sintered parts reduce values such as the magnetic permeability but service experience extended over a number [ ] of years has proven beyond doubt that in many instances the lower density of powder parts is not prohibitive to their use m replacement of machined magnetic parts The. magnetic requirements for pole shoes particularly the permeability, vary within wide limits, especially with the relative size of the air gap in the finished assembly. The overall permeability of an assembly, µ, is given by the formula [ ] where µm is the permeability of the core material, l the total length of the magnetic path, and a the length of the air gap. Fig 1 shows the variation of the overall permeability with the permeability of the core material, calculated according to Eq I for an air gap of 1 pct of the total length of the magnetic circuit. It is readily recognized that to use core materials hav-

Jan 1, 1948

By Francis M. Walters, Irwin R. Kramer

The substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient 01 expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and their use up to 400' or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. Experimental Methods Two methods were used in studying the stability of the low-expansion iron -nickel-cobalt alloys. Dilatometer specimens were held at 480°C. for 9 months and the change in expansion characteristics was dctcr- mined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1942

By M. H. De Hora

(Butte Meeting, August, 1913.) IN giving my opinion of the importance of Colombia as a field for investment for those interested in mining for the precious metals, I must begin by quoting Sir Clement Markham, who, in one of his presidential addresses to the Royal Geographical Society of Great Britain, called the attention of its members to the fact that " although Colombia is the least known and least developed of the South American republics, it is far and away the richest mineral country of then all." This to American investors is extremely interesting, as the country is the most accessible of all the South American republics from the United States. Almost all of the gold shipped by the Spaniards from Madre de Dios, now Colon, came from Colombia, and statistics from the Mint at Medellin, the capital of the Department of Antioquia, go to show that the total production of the precious metals of Colombia, dating from the Spanish conquest in 'the fifteenth century to the present time, aggregates the enormous total of $700,000,000. Of this amount, nearly 70 per cent. represents gold obtained from the placers of the Republic, more than one-half of which came from the Department of Antioquia, the balance being divided between the placers of the Choco and the rest of the Republic. The remaining 30 per cent. of the $700,000,000 represents the silver and gold obtained from the quartz mines, the silver greatly predominating.

Jan 7, 1913

By Francis M. Walters, Irwin R. Kramer

The substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient 01 expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and their use up to 400' or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. Experimental Methods Two methods were used in studying the stability of the low-expansion iron -nickel-cobalt alloys. Dilatometer specimens were held at 480°C. for 9 months and the change in expansion characteristics was dctcr- mined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1942

During the year terminating at the date for the third annual meeting of Engineering Foundation, the Board completed, its undertaking to sustain the National Research Council for one year. Assistance given in the organization of the National Research Council has been amply justified by the results. The Council is now well established in a 4¬story building at 1023 16th Street, N. W., Washington, and has recently secured another similar building near by in order to house its increasing force. The breadth, importance and volume of work done have steadily grown. Foreign offices have recently been established in London and Paris, Dr. H. A. Bumstead being in charge of the former and Dr. William F. Durand of the latter. The total expenditure by Engineering Foundation for the National Research Council was $9,036, derived partly from income of the endowment fund and partly from special gifts from Ambrose Swasey and Edward D. Adams. In May, Walter M. Gilbert was appointed Assistant Secretary of Engineering. Foundation, with headquarters in Washington, his services being contributed by the Carnegie Institution. He also became and has remained to date Assistant Secretary of the National Research Council. In September, resolutions were exchanged between the Engineering Foundation Board and the National Research Council, setting forth a policy of continuing reciprocal relationship, and a conference committee, Chairman M. I. Pupin, Dr. Charles Warren Hunt, and Gano Dunn, was appointed to inform the National Research Council of the readiness of Engineering Foundation to work upon definite problems sug-gested by the Council. No problems have yet been suggested.

Jan 5, 1918