Search Documents

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By Alexander Squire

A brief study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,' who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,l is concerned with the heat-treatment of steels formed by the car-burization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decar-burization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,-000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and 16 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to r200°C'. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

By E. H. Griswold

The surveying of oil wells has in recent months become a common practice in the deep fields of the Mid-Continent area. Borehole surveys have been made by mining companies for many years, but the introduction of such methods into the oil fields has been delayed until the past few years, because the value of survey data was not fully appreciated. The acid and gelatin bottle methods of obtaining the angle of deviation and the floating compass method of obtaining the direction of horizontal drift have been in use for more than 20 years. A photographic recording instrument consisting of a plumb bob, magnetic needle and electrically operated camera was devised and used in the Rand mining fields of South Africa prior to 1912.1 Another and improved photographic instrument, depending upon orientation of the drill pipe instead of polar magnetism for direction, has been invented and used. The acid bottle method has also been used in conjunction with oriented drill pipe. The magnetic compass is not reliable for oil-well work because of the unsymmetrical attraction of the needle to the well casing and possible magnetic formations. Many engineers also concur in the opinion that orientation of the drill pipe from instrument to surface will be inaccurate because of the torque exerted between the drill pipe and walls of the hole, causing the lower sections of pipe to twist. When it is considered that 4000 ft. of 6 in. drill pipe has approximately the same slender-ness ratio as 6 ft. of silk thread, such twisting effects can be readily visualized. The gyroscopic compass has been suggested for use in direction finding, but the high cost of such instruments will prohibit their use, except in special cases. Due to the lack of accurate direction-finding instruments, almost all of the survey work in the Mid-Continent fields has been of the acid bottle method alone.

Jan 1, 1929

There are not many data about early coal production in Kentucky, but some legislative reports, early geological studies and occasional newspaper articles have left some figures. The earliest production with any authentic record is that of Lee County, the coal being boated down the Kentucky River to Frankfort. While never a large producer, this county has the longest record in the State. Production is recorded in several of the western coal counties in 1820, and in several others a few years later. The early production in Greenup County was for the iron furnaces operating there. Clay County had a large salt output in the early days and this required a large output, for those days, of coal; the amount of fuel is based on the quantity of salt. It will be noticed that several counties on the Ohio River produced considerable quantities of coal before the Civil War, much of it being consumed by the river steamers. Since the end of the war, these counties have never occupied the relatively important position they had prior to that time. All of the coal produced in the eastern mountain counties moved out of them by water before the war, and during that struggle nearly all mining was stopped. The growth of the railroads after the war greatly reduced the river traffic from these counties, and in some cases it was never renewed. The coal shipped from Lawrence County prior to 1861 all moved by water; after that date there was no production excepting for local use until 1879, and since that time, all shipments have been by rail. Some of the early railroad reports have been helpful in reporting shipments, but for the early years very few of them can be found, and after about 1879 the quantities reported cannot be identified as to origin. Pres. J. B. Hill, Louisville and Nashville Railroad, furnished all of the data available for his line. Sources of data are shown on Table 61; other figures are estimated. A list of early Kentucky mines is given in Table 13.

Jan 1, 1942

By C. S. Barrett

WhEN a collimated beam of protons or other energetic particles is scattered by a single crystal, the emerging particles produce patterns that contain much crystallographic information. Calculations of the trajectories of individual particles can predict with reasonable accuracy the complete pattern (which is related reciprocally to channeling, now studied in detail6) but the task is a lengthy one which has been completed for very few cases. A many-beam dynamic diffraction calculation of the patterns would be even more difficult and in some cases may be invalid. Because of these complexities, simple methods that will predict to a rough approximation the relative intensities of the lines in films of the back-scattering patterns of a given crystal are wanted. I have found a method which, although it is not a valid computation of intensities or of film darkening by either dynamic or kinematic diffraction principles or by trajectory calculations, nevertheless is found to be useful in practice. It has been tested on several crystal types,7 and is here tested on additional ones. The method consists in first calculating the structure factor F(hk1) for the (hkl) plane, of spacing d, by the familiar equation: where the summation extends over the atoms in the unit cell and fj is the atom scattering factor of the jth atom (using tables computed for electron diffraction, preferably those computed without exchange). Then the F values are squared and summed over all the orders, n, for which F2 has an appreciable value, giving a quantity: Finally, I, is expressed as a percentage of Ic for the

Jan 1, 1970

By H. Shaw

IT is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment.

Jan 1, 1928

By Barry K. McMahon

The fundamental problem in rock mechanics is accounting for the discontinuous and anisotropic nature of the jointed rock mass. It is this problem that makes rock mechanics distinct from the mechanics of steel, glass, or concrete. Existing mathematical models explain much of the behavior of rock cores in the laboratory but, in civil engineering at least, the rocks that matter are the ones that are already broken. On the other hand, the basically descriptive methods now used in engineering geology do not lend themselves easily to mathematical analysis. A set of indices of geological properties related to the strength and deformation characteristics of jointed rock is needed. Like the index properties used in soil mechanics these will probably not have precise mathematical meaning, but once correlations are established with large scale tests they can form a basis for the transfer of test results, obtained in one area under one set of conditions, to the prediction of rock behavior in another area under another set of conditions. Indices of rock properties are even more important in rock mechanics than in soil mechanics as the cost of testing is much higher. To be useful, these indices must be easily and quickly measured and give reproducible results when measurements are made by different people. In this paper the word "joint" means all naturally occurring rock fractures with less than 3 in. of clay or other soft coating material. EXISTING INDICES OF ROCK PROPERTIES A comprehensive review of indices of rock properties for intact rock is given by Deere and Miller.' They provide charts ". . . for estimating the strength or modulus properties for intact rock from the numerical indices obtained by either the Schmidt hammer, the Shore Scleroscope,

Jan 1, 1968

JOHN B. HASTINGS, Los Angeles, Cal. (written discussion *).-This, paper is so admirable for its brevity that one hesitates to enter into discussion. The cycle of eruptives makes one wonder, "Where's the basalt?" and the youthfulness of the Idaho flows suggests they may yet come. Veins and Dikes.-Veins and dikes seem to be closely aligned in the minds of some authors, while to me they appear quite distinct, the first representing quiet, long-continued action, typified by metasomatic replacement, far removed from volcanic action; the latter, sudden and cyclonic, emanating from the heart of vulcanism. The rock openings occupied by both types were formed by kindred forces, but in the one they were closed for indefinite periods before invasion by the solfataric solutions, and in the other their formation and occupation were simultaneous. Open Fissures.-I do not believe in the existence of open spaces of discission that may be occupied by veins. Occasionally they occur; I found one with. a machine drill 350 ft. below surface, fortunately in an adit; the water spouted for 12 ft. in a 6-in stream for nearly 24 hr. It was only a flattish fissure, 6 in. wide, crossing the perpendicular vein, and indicating how tabular veins of ore might be formed. The practical absence of open fissures should be a joy to miners. We all know the misgivings with which we feel about for an old winze having only 30 ft. of water in it, in an unsurveyed and inaccessible part of a mine. It is said that veins are sometimes formed in open spaces left by Protuberances of the walls, which meet after having been displaced; but I believe that in such circumstances there would be sufficient attrition and brecciated material to fill the fissure, though perhaps loosely. Parts of veins may possibly have been formed in originally open spaces, but if so, the spaces were made by solution shortly preceding the deposition of the veins. That total solution of rock adjacent to a fissure may occur under favorable conditions is proved by the existence of large bodies of sulphide which contain only a few per cent. of silica; while on the same level, and in other levels above and below, all being within the same ore shoot, assays may show as much as 50 to 60 per cent. of silica, although the gold, silver and copper assays may be almost identical in all the

Jan 1, 1918

By John Dilworth

THIS paper treats primarily of the valuation of developed coal properties by the method of capitalizing their estimated average future earnings. However, in it reference is also made to valuations of undeveloped coal lands and to various methods of appraisal other than by future earnings. FUNDAMENTAL VALUATION PRINCIPLES Before discussing in detail coal property valuations, a few statements bearing on the general subject will be made to present certain of the writer's views on the question as a whole. 1. A certain property at a given time has but, one true value. This is not universally admitted. The appraiser rather frequently finds that a coal owner has in mind three valuations for his holdings; one, the figure at which he feels they should be appraised for taxation purposes; another, the much higher one that should be used if a loan is to he negotiated on the property; and a third, intermediate between the other two, the price for which he would be willing to dispose of his holdings were they for sale. The last is usually nearest to the true value, and because this is so the statement is generally accepted that the fair value of such a property is the price arrived at by negotiation between a willing seller and a willing buyer who are otherwise disinterested. 2. Notwithstanding the foregoing, it is only very generally and approximately true that the proper measure of the value of a given developed1 coal acreage is the unit or per-acre price for which one or more bodies of similar coal in the salve district have been sold recently. To give a few reasons why such a measure of value can not be strictly applied, it may be noted:

Jan 1, 1927

By P. C. Claspy, P. H. Smakula

The electro-optic coefficients of LiNbO, and KTao.,5Nboe3,O3 (KTN) have been experimentally determined at the HeNe laser wavelengths of 0.6328, 1.15, and 3.39 µ. The coefficients were calculated fronz the retardation induced by an applied electric field. The retardations were measured by observing one or move transmission maxima and minima as a function of the applied field, and by measuring the retardation directly with a Babinet-Soleil compensator. The values obtained agree quite well with those previo~lsly reported by others. Extinction ratios as high as 3000:l have been observed. Resistivities and Curie temperatures have also been measured. Light-induced optical inhornogeneities in LiNbO, repovted by others have been observed. CONSIDERABLE interest has recently been shown in the electro-optic properties of LiNb03 (Refs. 1 and 2) and KTN.3, 4 These crystals have a number of advantages over such well-known materials as KDP. These advantages include: 1) the infrared transmission of KTN and LiNb03 extends to 5 p whereas that of KDP cuts off at 1.5 p ; 2) driving voltages required for modulators using these materials are considerably lower than those required for KDP. After first discussing some theoretical considerations of the electro-optic effect, we will report the results of measurements of the dc electro-optic coefficients of these materials at wavelengths of 0.6328, 1.15, and 3.39 p. THEORY The generalized equation for the electro-optic effect can be written: Although lattice polarization is the fundamental variable, rather than the applied electric field, we follow the convention of expressing the linear electro-optic effect in terms of the applied field. For LiNbO the quadratic terms are negligible. Since KTN has a center of symmetry the rijk tensor is 0. After applying the usual symmetry considerations and index contractions,* the rijk and gijkl tensors can be expressed as follows: LiNbOaT If field directions are now chosen, the change in refractive index and the angle between the induced optic axes and the crystallographic axes can be found. The induced rotations of the principal axes of the index ellipsoid for fields in principal crystallographic directions are given in Table I. Since KTN is initially isotropic, the principal axes in the zero-field condition are parallel to the crystallographic axes. The induced retardations are given in Table 11. EXPERIMENTAL We obtained the various electro-optic coefficients by measuring the induced retardation as a function of

Jan 1, 1968

By E. B. Hunt, T. M. Geffen, C. R. Stewart, V. J. Berry

Laboratory data .show that the gas-oil ratio performance of non-uniform porosity limestones produced by solution gas drive is sensitive to producing rate and to fluid properties. Nan-uniform porosity limestones are those for which laboratcry solution and external gas drive tests yield considerably different relative permeability ratio characterislics. The oil recovery performance by solution gas drive depends directly on the number of gas bubbles formed. Laboratory rates of pressure decline, which are 100 to 10,000 times greater than normal field rates. cause the formation of an unusually large number of gas bubbles. This results in abnormally high oil recovery efficiencies. Since it is impractical to reproduce the number of bubbles formed under field conditions, laboratory solution gas drive data on non-uniform porosity limestones are therefore not directly applicable to field operations. However, certain laboratory data can be used to make a conservative estimate of field performance. The concepts presented in this paper indicate the possibility that increased field oil recoveries may he obtained from non-uniform porosity limestones by rap- idly reducing reservoir pressure for a short interval of time. It has yet to be established that significant improvements in oil recovery from such reservoirs can he realized by varying the pressure decline rate within limits possible in the field. However, the possibility that recovery may be increased in this manner warrants further study. INTRODUCTION Limestone reservoir rocks can be divided into two general classes according to the nature of their pore space. One class has a comparatively uniform pore system composed mainly of voids between grains of the rock (intergranular type porosity). The other class, in addition to having intergranular porosity, has a secondary pore system composed of combinations of solution cavities, fractures, etc., and is considered to have non-uniform porosity. It has been shown in a previous publication' that the laboratory measured gas-oil flow behavior of uniform type porosity limestones is essentially the same for a test simulating a field solution gas drive as for one simulating an external gas drive. For non-uniform porosity type limestones a significant difference in gas-oil flow behavior was found. More efficient behavior was

Jan 1, 1955

By William G. Krantz

The increased service demands on some of the products of the National Mallcable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process had already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 Ib. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give US good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 04 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect. In proper operation lies the whole secret of success. That steel has been made electrically means nothing, for when the furnace is operated under oxidizing conditions the quality is no better than that of open-hearth material; but when properly made, electric steel is as good as

Jan 1, 1916

By John P. Hager, Adolfo R. Zambrano

The thermodynamics properties of the liquid Pb-Ag-Au system have been determined from galvanic cell measurments five pseudobinary systems of fixed XAg/XAu ratio. The galvanic cell employed a molten PbO-SiO2 electrolyte and was operated between 775" and 1030°C. The thermodynamics properties of lead were obtained directly from the experimental data, whereas the excess integral molar properties and the activities of silver and gold were obtained by means of the Gibbs-Duhem equation. The calculated proper -ties of the Ag-Au system agree well with the published properties. The liquidus surface of the Pb-Ag-Au system has been determined at 1200°K. In Parts I' and 11' the galvanic cell Mo,Pb(l)|(PbO-SiO2)(l) SiO2(s) |Pb(alloy)(l), Mo [I] was used to determine the thermodynamics properties of the Pb-Ag and Pb-Au systems, respectively. The use of cell I, in which a molten oxide electrolyte is employed rather than the classical fused-salt electrolyte, was shown to result in more accurate ther-modynamic measurements in that the displacement reaction at the alloy-electrolyte interface (l/Zb)B(alloy) + (I/za)A+Za = (1/Za)A(alloy) + (1/Zb)B+zb [1] was minimized. For the Pb-Ag system, where B = Ag(l), the error in the activity of lead (aPd) re-sulting from Reaction [I] was calculated to be less than 1 pct.l For the Pb-Au system the error in aPb was calculated to be less than 0.5 pct.2 Also, electro-transport measurements on the PbO-SiO2 electro-lyte1,2 established that the conduction was entirely ionic and that lead was present only in the divalent state. In the present study the experimental technique is extended to an investigation of the thermodynamic properties of the liquid Pb-Ag-Au system. Five pseudobinary systems of fixed X Ag/XAu ratio were selected. The experimental results were then combined with the previous measurements on the component binary systems Pb-Ag1 and Pb-AU2 to calculate, by means of the Gibbs-Duhem equation, the molar and partial molar mixing properties for the liquid ternary solutions.

Jan 1, 1970

By Benjamin S. Lindsey, James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325 mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent Si02, and 2.85 per cent R203. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder ,was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.' The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O'Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By H. C. van Elst

Ultrahigh-speedphotographic and electronic meth-ods were applied to an investigation of details of brittle-fracture propagation in steel. The brittle fractures studied were obtained in steel plate with the aid of a Robertson apparatus. It was found that a brittle fracture proceeds by discrete steps ranging from 30 mm near the stop temperature to less than 2 mm at lower temperatures. The halting FROM prior metallographic observations of brittle fracture in steel' it could be concluded that the distribution of mechanical twins along a brittle fracture was similar to the distribution of mechanical twins induced by explosive deformation. It was therefore assumed that a running brittle fracture created stress waves, cf. Refs. 2-7. An emission of stress waves by a brittle fracture, however, seems only conceivable if the fracture propagates by discrete steps. For this reason a study of the details of times between successive steps drop in this tem-perature region from 20 usec to about 1 psec. The stepwise propagation mechanism is accompanied by an intermittent emission of stress waves of the order of 100 to 200 kg per sq mm. These stress waves seen1 to play an important role in the mechanism of brittle fracture as will be discussed. brittle-fracture propagation was undertaken to investigate the possible determination of the fracture steps and the emitted stress waves associated with the assumed mechanism. The more practical object of this work is the development of a test method for the determination of the ductile-brittle transition in small specimens. This has special advantages for the study of irradiation damage in steel. In this test method, which will be published in a following paper, the stress waves emitted by an actual brittle fracture are reproduced with explosive or electrical means and are then transmitted through small specimens at various temperatures. In the present paper only the results of the brittle-fracture study will be reported.

Jan 1, 1964

By John Dorn

THE phenomenon of diffusion, according to the most prevalent conceptions at the present time, undoubtedly played an important part in the formation and distribution of metals and minerals in the earth's crust. Apparently there is good evidence that in the geological rate of cooling diffusion caused numerous materials to separate into individual masses or into duplex structures. As is well known, the early steels were made by cementation; that is, by heating wrought ferrous metal in contact with carburizing materials so as to produce a relatively high carbon content on the surface. If the process was continued long enough, the carbon diffused throughout the piece. A more homogeneous product depended upon further heating and forging, so that the carbon diffused to a fairly uniform concentration throughout the metal. In the modern metallurgical industry, diffusion is the basis for many operations; for example, the production of hard surfaces oil steels by carburizing, nitriding, cementing with chromium, silicon, boron and beryllium. Castings or ingots as they solidify do not have homogeneous structures, but these structures are made largely homogeneous by suitable process of heat-treating and the resulting diffusion. It is in modern physical metallurgy, however, that we become greatly concerned about the mechanism of the phenomenon of diffusion. The rates of diffusion, effect of temperature and time on diffusion, and the relation of diffusion to the many properties of the parent metal and the diffusing metal have become important; also, we are concerned with the diffusion of a single metal into a complex alloy. For example, what is the mechanism whereby carbon and nitrogen travel into steel? What is the effect of alloying elements in the ferrous material on the rates of diffu-sions? What is the effect of simultaneous diffusion of carbon and nitro-gen? How does chromium, beryllium, boron, or the like, diffuse into the steel, and what are the effects of alloying elements in the steel previous to the cementation process? These inquiries are by no means limited

Jan 1, 1937

By J. F. Myers, F. M. Lewis

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons."

Jan 11, 1950

By S. R. Krogh, T. O. Olsen

Analytical expressions for the breakage rate as functions of mill charge, mill speed, particle size, ball diameter, and ball load are derived, using idealized models for probability of breakage (Gaudin and Meloy), energy distribution (Mempel), and arithmetic mean of effective ball energy (Langemanns). Computational results using the theoretical equations are compared to experiments. The equations enable simulation of ball mill grinding at different grinding conditions.

Jan 1, 1973

By Stanley L. Arnot

The Mother Lode district in California is probably better known as the land of Bret Harte and Mark Twain than as a gold-producing district, although in this respect it holds an important place. The history of quartz mining on the Mother Lode dates back to the '50s, when, after the first fever of the gold rush, men began to look for something more permanent, if not more lucrative, than the placers. Since that time, the discoveries, shutdowns, and reopenings of the many mines, together with the varying fortunes of their numerous operators, constitute an interesting chapter in California history, but one too long to include in a description of mining methods. The district is well situated, so far as physical conditions are concerned. The Mother Lode extends along the western slope of the Sierra Nevada Mountains, about half way between the crest and the Sacramento and San Joaquin Valleys, the country traversed consisting of low rolling hills—typical foot-hills. The elevation varies from 1000 to 1800 ft. and the climate is most desirable. There is an abundance of water, timber is easily obtained from the higher foot-hills a few miles east, and cheap hydro-electric power is generated practically on the Lode. These natural conditions are conducive to low costs in mining and have been the deciding factor in allowing profitable exploitation of the comparatively low-grade orebodies. Transportation facilities are not bad. Five branch railroads, from the main trunk lines in the valley, tap the district at intervals of from 10 to 30 miles, and the roads connecting these are fairly good for trucking purposes. Labor is made up of several nationalities, the principal ones being American, Spanish, Jugo-Slav, Italian, and Mexican. There were few Mexicans on the Lode prior to 1919, but the shortage of labor, experienced generally by the mining camps of the country in the years following the war, made necessary the hiring of some. The percentage of Mexican labor rapidly increased in 1920 and for a year or so thereafter, but it has now diminished until at most of the mines only a few Mexicans are working. Of the different nationalities, Americans are the most efficient and Mexicans the least.

Jan 1, 1925

By H. W. Imholz

This report covers most of the counties in North Central Texas in which oil is being produced in commercial quantities. The exceptions are McCulloch and Runnels, which were omitted because the production is small and the detailed information necessary for a report is not available to the writer. Complete information was not available regarding the number of wells drilled in this district during the year. The writer wishes to thank Mr. T. F. Petty, of the Humble Oil and Refining Co., Wichita Falls, Texas, for information used in compiling Table 2.

Jan 1, 1937