Search Documents

The Empire IV expansion is on schedule for completion in January 1980; Hibbing Taconite's 2.7 million ltpy* expansion should be finished late in 1979; and Reserve Mining's tailing disposal project is on target for April 1980. Erie Mining Co., the first to bring 170-ton haulage trucks to the Mesabi Range, reports excellent operating results, and Inland Steel expects to produce 80% of its pellets in 1979 using coal rather than oil. One Michigan mine has so many inspectors that it has hired a school bus to transport them around the operation; and a contractor reports that mine construction projects of the future may require the training of 15,000 workers. All of this was covered at the 52nd Annual Minnesota Section AIME Meeting and the 40th University of Minnesota Mining Symposium, a joint event held each January in Duluth.

Jan 3, 1979

By D. G. Hartley, P. C. Hayward, K. R. Weller, U. J. Sterns

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five Primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balk. For five months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm (2 to 1.1 in.). Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balk. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 2%.

Jan 1, 1984

By Charles B. Forgan

THE Stan Trg ore body now being exploited by Trepca Mines, Ltd., originated by the metasomatic replacement of limestone and consists mainly of an intimate mixture of sulfides associated with little admixed gangue. The chief sulfides are galena, marmatite, pyrite, and pyrrhotite. Geological structure, embracing both igneous and sedimentary agencies, exerts important control on ore deposition and presents many features of great interest. Geological Formations and Intrusives Stag Trg Series-The dominant formation is the Stan Trg series, which

Jan 1, 1936

THE ladle is a small hearth made on a cage of iron bars like a bird-cage, and has a handle so that it can easily be taken from the forge and carried wherever desired. It is a common device and is much used among masters for small castings, but with a large weight you would have difficulty in lifting it by hand even though you were aided by levers and winches. If you should indeed do it, it would be just as if you had lifted the aforesaid hearth by force, and this would be unwise if you could do anything less difficult. A forge is likewise made for this, with a good pair of large bellows that are well covered with cloth. When the small hearth has been made with good clay, baked, and well covered with ashes, it is placed in front of the mouth [of the bellows] and a crown of two or three brick ends is built around it on top of the rim so that the charcoal may be held better and in greater quantity. Then, having lit the fire and heated the ladle and the charcoal, the pieces of material that you wish to melt are gradually put on

Jan 1, 1942

By T. Inoue, T. Imaizumi

A simulation model has been developed to find out the possibility of improving the industrial closed-circuit wet grinding operations. The model involves a continuous tumbling mill in combination with a hydrocyclone to recycle the oversize material back to the mill. The mill is described by the breakage, i.e. the selection and the distribution, functions, co-ordinated with the diffusional mixing along the axis. The cyclone classifier is characterized by the partition function with allowance for the non-selective separation of part of the feed material into the underflow. The computer program developed incorporates an interactive capability to modify the operating conditions of the system whenever needed. The results are analysed for the operational conditions characterizing the mill and the classifier. Besides the steady state conditions some observations are also made about the dynamic responses of the closed circuit grinding system.

Jan 1, 1980

By D. W. Fuerstenau

Locked-cycle grinding experiments on mineral mixtures provide a means to study circuit performance in simulated continuous grinding systems. Such experiments with calcite/quartz mixtures revealed that approximately twenty-five 2-minute cycles are required before the composition of the circuit product and the recycle material attain steady state. The circulating load, after steadily increasing during the first 15 cycles, continued to fluctuate over a narrow range. Previous batch ball mill grinding of mineral mixtures has shown that breakage rate functions of minerals are time- independent but composition-dependent. In the closed-circuit grinding of ores with constituents having different grindabilities, the grinding rate parameters for the components also would therefore change during the transient period. With fluctuations in feed composition occurring randomly every half to one hour in processing plants, it is quite likely that the grinding circuit can be in unsteady state perpetually. The significance of these observations is discussed in this paper in the con- text of the models used in control schemes for the grinding circuits

Jan 1, 1984

By Raynor Linzey, Karl M. Busen

The formation of thin films of silicon oxide by anodic oxidation of silicon and the subsequent removal of these films by an etch is a process often used for the evaluation of concentration distributions Profiles) in silicon layers by the differential sheet conductance method. The accuracy of the resulting profile is very strongly influenced by the uniformity of the thickness of the reacted silicon. Normally, it would be expected that for a constant number of coulombs passed the thickness would be the same from oxidation to oxidation. Investigations show that in certain electrolytes, for a given number of coulombs passed through an n-type silicon sample, the thickness of the reacted silicon increased with increasing resistivity. Even for the same resistivity the thickness varied sometimes by a factor of 1.5. When an electrolyte was used which consisted of 10 pct water by volume in ethylene glycol with 4.0 g KNO per 1000 ml of solution, anodiza-tion at 5 ma per sq cm led to satisfying results. Short-time anodizations gave oxide layers of a higher apparent density than those experienced from thermally gown silicon oxides. THE functioning and the electrical characteristics of semiconductor devices are based upon the incorporation of "impurities" into a single-crystalline body of suitable material and on the concentration distribution (profile) of this impurity. The incorporation can be achieved by well-known processes as, for example, by diffusion, epitaxial growth, alloying, or ion implantation. Often the profile resulting from these processes is not known. A powerful tool to learn about a concentration distribution is given by the method of differential sheet conductance which employs successive four-probe measurements on a layer subjected to stepwise removal of thin sublayers. Differential sheet conductance vs position (or penetration depth) of a sublayer is plotted and a smooth curve is drawn through the data. From this curve the profile is then calculated. When the semiconductor material is silicon, the sublayers are removed suitably by anodic oxidation of the silicon and subsequent dissolving of the formed silicon oxide by an etch. The accuracy of the resulting profile is very strongly influenced by the uniformity of the sublayer thickness. Normally, it would be expected that, for a constant number of coulombs passed, the thickness would be constant from oxidation to oxidation. Investigations showed that for sublayers several hundred angstroms thick the reproducibility can be rather poor. Therefore, efforts were made to obtain a reliable technique for uniform removal. The present paper describes such a technique and certain phenomena which were encountered during the investigations. APPARATUS AND TECHNIQUE The first report on the investigation of concentration distributions, where for differential sheet conductance measurements thin silicon sublayers were removed from a diffused layer by anodic oxidation, was given by Tannenbaum. The author reports the removal of sublayers which for the most part were 400 thick. More advanced device designs now require much narrower layers. When it was tried in these laboratories to determine profiles within such layers, difficulties were encountered with respect to sublayers which by necessity had to be thinner than the ones reported by Tannenbaum. The apparatus used for the investigations is sketched in Fig. 1. Two cylindrical containers connected by a wide tube are filled with an electrolyte. The left container receives the cathode whereas the right container is closed at the bottom end by a sample support consisting of a Teflon base and a copper pedestal. The silicon sample (1 by 1 cm) is mounted to the pedestal embedded flush in the Teflon base using silver paint (Degussa) for electrical contact. Pyseal is applied to the edges of the sample to protect the copper pedestal from the electrolyte. The base is mounted to the container using a water-tight silicon rubber gasket. Fig. 2 gives a view of the sample support. The copper pedestal is connected to the positive side of a power supply operating at a constant current output (Kepco Model ABC 425M). The electrolyte which has been reported by Duffek et al. consisted of either 2 or 10 pct water by volume in ethylene glycol and 4.0 g KNO3 in 1000-ml solution. The electrolyte is best prepared

Jan 1, 1967

By A. Eilers

In a former paper on Western Smelting Works, I mentioned the great difficulty of obtaining accurate information in regard to the economy of the processes in practice; and to-day, although nearly two years have elapsed since my former paper was written, I am sorry to say that very little improvement has taken place in the keeping of accounts, and in the direction of a more systematic management in the majority of these works. But I am quite certain that by this time even the most sanguine furnace managers must have become convinced, from the experience of the last year, that somewhere in their processes there are enormous losses. Rates for the purchase of ores in 1873 were not as high as they were in former years in certain parts of the country ; labor was no 'higher than formerly; the demand for unparted lead was good throughout the year, with the only exception of the time of the panic, in the fall of 1873; yet there are, of between 40 and 50 works, not more than two or three in Utah and Nevada to-day, that have paid a reasonable interest on the capital invested.

By A. Filers

IN a former paper on Western Smelting Works, I mentioned the great difficulty of obtaining accurate information in regard to the economy of the processes in practice ; and to-day, although nearly two years have elapsed since my former paper was written, I am sorry to say that very little improvement has taken place in the keeping of accounts, and in the direction of a more systematic management in the majority of these works. But I am quite certain that by this time even the most sanguine furnace managers must have become convinced, from the experience of the last year, that somewhere in their processes there are enormous losses. Rates for the purchase of ores in 1873 were not as high as they were in former years in certain parts of the country ; labor was no higher than formerly ; the demand for unparted lead was good throughout the year, with the only exception of the time of the panic, in the fall of 1873; yet there are, of between 40 and 50 works, not more than two or three in Utah and Nevada to-day, that have paid a reasonable interest on the capital invested.

Jan 1, 1875

By E. R. Atkins, G. H. Smith

Results of laboratory tests are presented to show that lire value of "m", in the Archie expression dernlined by the shapes of the particles in the system. Tile value of m "the shape factor", is constant for a system of particles of a given shape for a range of F - + values. Applying this concept, one can predict F - + relationships for mixtures of particles with different shapes, and these predicted relationships are useful in electric log interpretation. It is suggested that an equation of the form 1/F -10mcan be used to describe the properties of natural formations containing varying amounts of sand and clay. From this work and values of "a" and "m" reported in the literature, it appears that in many cases rocks in the same geological horizon have a common primary porosity but contain varying amounts of a particular clay. It is concluded that the equation can be applied to a rock-water system only when values of "a" and "m" have been established for the particular system. INTRODUCTION The petroleum literature contains many reports of the results obtained by determining formation resistivity factor F and porosity + of rock samples from oil fields all over the world. The usual practice is to use data from a large number of samples from a number of fields to find an average relationship between F and +. Several such average relationships have been advanced. In the absence of data on a particular formation or field, it has been the practice to use the average relationships to give a rough approximation of the F - + relationship. The purpose of this paper is to report on basic relationships that exist between F and + for naturally occurring particles in water solutions. Other workers' have found the same relationships apply to the diffusion of hydrogen through packed beds of dry particles. In the work discussed here, relationships for application to unconsolidated sands or shales containing mix- tures of particle shapes are derived. These relationships, developed for unconsolidated formations, may apply to consolidated formations. EXPERIMENTAL To evaluate F- relationships for unconsolidated rocks, the results of laboratory measurements on simple slurries of clay or sand will be used. Such laboratory studies are concerned with the electrical behavior of water-containing rocks. The wet rock constituents are electrically similar in slurries and in rocks. Archie2 defined formation resistivity factor as All resistance measurements were made using a 1,000-cycle impedance bridge with an oscilloscope as the null detector." The accuracy of this bridge was better than * 0.15 per cent. For the particular apparatus employed, no additional reactance was required to achieve balance for samples with resistances between

By R. W. Smith, R. J. Charles

Fractions of glass particles in the size range 0.5 to 5.0 were prepared by an elutriator that operates in a centrifugal field. Although mean sizes of commercially graded abrasive powders were ten times greater than those of samples prepared by the elutriator, frequency size plots for elutriator samples compared favorably. Efficiency of separation was low and amounts of material recovered by the elutriator were small, but the method should find use in preparation of small amounts of sized materials for laboratory investigations. R. W. SMITH, Junior Member AIME, Research Assistant, Dept. of Metallurgy, Massachusetts Institute of Technology, is presently with Portland Cement Ass'n., Chicago. R. J. CHARLES, Junior Member AIME, formerly Assistant Professor, Dept. of Metallurgy, Massachusetts Institute of Technology, is Research Associate, Ceramic Studies Section, General Electric Co., Schenectady, N. Y. TP 4261B. Manuscript, Jan. 31, 1956. STUDY of light adsorption, reaction rates, electro-phoresis, particle packing, and corrosion is hindered by lack of a suitable method of preparing small amounts of closely sized materials in the micron and submicron range. Most fractionation methods depend on some form of particle movement through a viscous media in which velocity of a par-

Jan 1, 1957

By T. A. Read, M. S. Wechsler, D. S. Lieberman

IN the formation of martensite in steel, it has been observed that the habit plane does not change continuously as the alloy content is varied. Instead, it appears that discrete habits correspond to certain ranges of composition. Greninger and Troiano' found that in low-, medium-, and high-carbon steels, the habits are approximately (1l1), (225), and (259), respectively.* The work of Mehl and Van Winkle2 indicated that the change from the (225) to the (259) habit is fundamentally a consequence of the lower transformation temperature rather than the higher carbon content. Also, Otte and Read3 observed that the habit plane orientation for a chrome-carbon steel scattered within a cone of semivertex angle of 5 deg, which was outside of the experimental error in the determination of the habit plane. These observations suggest the importance of investigating what factors in the crystallography of the formation of martensite account for the several types of habit and the inherent scatter in the precise orientation of the habit plane. A theoretical treatment of the austenite-martensite transformation has been given,4 which considers the total transformation distortion to be composed

Jan 1, 1961

By S. Edward Drummond, Charles D. Haynes, Stephen H. Stow

This paper is a preliminary report on the occurrence and distribution of economically interesting heavy minerals (kyanite, sillimanite, staurolite, zircon, monazite, ilmenite, leucoxene, rutile) in sands from the sea floor surface of the offshore area, Alabama-Mississippi. Weight percent of heavies derived from the +60 portion of 97 samples is contoured in [Fig. 1]. Five hundred grains from 42 of the heavy mineral separates were identified and sized microscopically; the data were converted to weight percent for each mineral species and are summarized in [Table 1]. Heavy Mineral Distribution In the Gulf, there is a general westward decrease [(Fig. 1)] in maximum abundance of heavies from 2.4% north of Sand Island at the mouth of Mobile Bay to slightly over 1.0% south of Petit Bois Island and a corresponding decrease in the Mississippi Sound from 1.4%, north of Dauphin Island to slightly over 0.25% north of Horn Island. Average concentrations of heavies for different areas are found in Table 1. There is westerly longshore transport in this area; the interaction of the longshore current with discharge from Mobile Bay and disruptions of the current by Sand Island, possibly aided by a shoaling effect, appear to be the cause of the preferential deposition and concentration of heavies (2.4%) north of Sand Island in 10 to 14 ft of water.

Jan 1, 1977

By M. J. Marcinkowski, R. M. Fisher

The flow stress-grain size relationship has been determined at room temperature in both a disordered and a fully ordered FeCo for plastic strains up to 30 pct. The results are in agreement with a Hall-Petch relation of the type given by Of =a,+kd-1/2 where of is the flour stress and a, increases mono-tonically with increasing strain to a maximum value which is much higher for the ordered than for the disordered alloy. The slope, k, is found to increase FOLLOWING the original work of Halll and petch relating the effect of grain size to the lower yield stress of iron and steel, it has been generally found that the yield stress oy.s. of polycrystalline metals with strain to a maximum and then decrease for both ordered and disordered alloys. However, k for the ordered alloy is in general higher than that for the disordered alloy and the critical strain for k max somewhat larger. All of these observations can be satisfactorily accounted for quantitatively and in some cases semiquantitatively by using a slip band-grain boundary intersection model, and by taking note of the fact that, in general, moss slip, while quite common in the disordered alloy, is extremely difficult in the ordered alloy. obeys a relation of the form oy.s.=a0+kd-1/2 [1] where a, and k are constants and d is the mean grain diameter. For convenience, and in accord with prevailing custom, Eq. [I] will be referred to simply as the Petch relation. Tjerkstra3 and Armstrong, Codd, Douthwaite, and petch4 showed that the flow stress af of iron or steel measured at strains of up to at least 20 pct also obeyed a relationship of the type given by Eq. (11. The latter investigators have also shown that Eq. [I] applies to fcc and hcp metals and alloys.

Jan 1, 1965

By V. R. Garfias, R. V. Whetsel, J. W. Ristori

Preliminary estimates indicate that world consumption of petroleum and related fuels in 1938 will be close to 1,908,000,000 bbl., or approximately 7,000,000 bbl. less than in 1937. This total does not include military consumption in foreign countries, which for obvious reasons is not made public. Foreign military consumption in any one year, however, is approximately represented by the difference between the total production of petroleum and related fuels and the "partial total" consumption above noted, after adding any decrease, or subtracting any increase in stocks in the United States. Fig. 1 illustrates this "difference" and shows that in 1937 and 1938, owing to the wars in China and Spain and the possibility of armed conflict in Central Europe, foreign military consumption—and possibly additions to foreign stocks—increased nearly 70,000,000 bbl. in 1937 over 1936 and remained at this high rate throughout 1938. No official information on foreign oil stocks is available to the writers. Table 1, recently published, purports to give the oil in storage in some of the European countries, but it is not known whether the figures include oil stocks for military purposes. It should be noted that with the annexation by Germany of Austria and part of Czechoslovakia the consumption of the country has increased to 53,000,000 bbl., which is about 36,000,000 short of the German produc-

Jan 1, 1939

By J. W. Ristori, R. V. Whetsel, V. R. Garfias

Preliminary estimates indicate that world consumption of petroleum and related fuels in 1938 will be close to 1,908,000,000 bbl., or approximately 7,000,000 bbl. less than in 1937. This total does not include military consumption in foreign countries, which for obvious reasons is not made public. Foreign military consumption in any one year, however, is approximately represented by the difference between the total production of petroleum and related fuels and the "partial total" consumption above noted, after adding any decrease, or subtracting any increase in stocks in the United States. Fig. 1 illustrates this "difference" and shows that in 1937 and 1938, owing to the wars in China and Spain and the possibility of armed conflict in Central Europe, foreign military consumption—and possibly additions to foreign stocks—increased nearly 70,000,000 bbl. in 1937 over 1936 and remained at this high rate throughout 1938. No official information on foreign oil stocks is available to the writers. Table 1, recently published, purports to give the oil in storage in some of the European countries, but it is not known whether the figures include oil stocks for military purposes. It should be noted that with the annexation by Germany of Austria and part of Czechoslovakia the consumption of the country has increased to 53,000,000 bbl., which is about 36,000,000 short of the German produc-

Jan 1, 1939

By C. B. Manula, R. Venkataramani, T. V. Falkie

A linear programming model has been developed to solve a production planning problem for a multi-plant stone operation serving several customers. The factors considered are production capacities, inventory restrictions, demand requirements, and available stone reserves. The objective function to be optimized is the total annual net returns from the quarry operations. For the purposes of model testing, annual stone sales from each plant were divided monthwise, productwise, and assigned to a market. The concept of assigning demands to market sectors and not to any particular plant creates the self-correcting interplay between the plants and the markets. Along with the inventory restrictions, and ending inventory requirements, this interaction enables the model to minimize the external diseconomics. The model was tested against an operating prototype and a number of alternative problems were also considered. Finally, the basic linear programming model has been enlarged by the addition of another dimension and the problem has been derived in a decomposition format.

Jan 1, 1972

By R. W. Prouty

THE methods of sampling and ore estimating used at the Copper Queen Branch, Phelps Dodge Corpn., as applied to the Copper Queen mines at Bisbee, Ariz., fall into two divisions because of the difference in occurrence, manner of prospecting, and methods of mining: that for the underground operations and that for the Sacramento Hill steam-shovel operations. The orebodies of the Warren district may be divided into three classes: Replacements of limestone, replace-ments of porphyry, and replacements of contact breccia The first class is more or less intimately related to porphyry intrusions, although in badly fractured country this relationship may not be well shown. These orebodies are mainly oxide and carbonate ore and very irregular, both in size and outline, although usually roughly lenticular and following the bedding of the limestones. There is usually quite a sharp boundary between the ore and waste in the carbonate and oxide orebodies and sampling is not necessary to determine the limits of commercial ore. In the sulfide orebodies it is exceedingly difficult, without sampling, to deter-mine the boundary between commercial ore and the surrounding low-grade or barren pyrite. Calculations made a few years ago showed that these orebodies had an average thickness of 35 ft. As some of the ore-bodies have a thickness of from 100 to 300 ft., it can be seen that the smaller ones form a difficult problem both in prospecting and in estimating.

Jan 11, 1922

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating tables of modern design on unclassified feeds of --1/2 in. particle sizes, including tests on high-sulphur coals.

Jan 9, 1950

By John V. Beall

Runding the bottom corner of the West Africa11 hump, one hovers off the coast of the tiny Republic of Liberia. But not for long-as Portuguese navigators, Blackbirders, and Farrell Line captains have learned. The ponderous swell of the Atlantic is driven by an on-shore wind that never dies. As remorseless as the Atlantic chewing away at the unbroken shoreline, is the country beyond-West Africa, where white meets black, where desert blends to bush to impenetrable jungle, where elephants chomp the foliage of young trees. This is a land from which the tsetse fly has driven the cattle, and the root crops grow big and voluptuous above the ground and are shrunken and barren of nutrient below. This is the environment of Liberia which is elbowing an iron ore market for itself on crowded shelves. Liberia is an anomaly in Africa. It was the first republic on the continent in modern times, having been established in 1848. While most of Africa was benefiting from the investment of foreign capital under colonial regimes, Liberia was going it alone. To be sure, Liberia was aware of foreign activity as hunks of territory were lopped off by neighboring French and English colonies. Today the country is about 43,000 sq miles, the size of Tennessee, which, in the language of exploration men, is a workable size unit.

Jan 12, 1962