Search Documents

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922

By C. D. Keen

IN the latter part of the summer of 1913 the Conservation Commission of the State of Louisiana, under presidency of M. L. Alexander, decided to stop the waste of natural gas going on at the "burning gas-well," located about 3/4 mile southeast of Oil City, La. On several occasions, both in newspapers and in reports, comment had been made on the condition of this well, its harmful effect on the Caddo gas field, and the considerable loss, estimated at several thousand dollars each month, caused by the escape of the valuable fuel. But nothing had been done to bring the well under control and prevent further waste of gas until the State Conservation Commission took the matter in hand. The gas fields of Louisiana are among the greatest in the country. So far most of the gas has been found in the Caddo field proper, although considerable development has been done in and around the city of Shreveport and near the town of Mansfield in DeSoto parish. To extend the life of the gas fields and to prevent the quick exhaustion of the supply of the natural fuel are matters of vital importance for this section of the country. Four gas companies have entered the Caddo field and supply the surrounding towns and cities with gas. The Arkansas Natural Gas Co. has pipe lines to Little Rock, Ark., and supplies gas to the following cities and towns in that State: Texarkana, Hope, Garland, Emmet, Prescott, Boughton, Beirne, Gurdon, Arkadelphia, Gum Springs, Malvern, Donaldson, Gifford, Perla,- Beaton, Beauxite, Mabelvale, Bryant, Sheridan, Pine Bluff, Little Rock, Argenta, Pulaski Heights, and Hot Springs. The Southwestern Gas & Electric Co. transports gas to Mooringsport, Blanchard, Caddo, Rodessa, Oil City, Vivian, Bloomburg, Hosston, Ida, Dixie, Belcher, and Shreveport. The Marshall Gas Co. supplies gas to the town of Marshall, Texas. The Louisiana Co. has a line to Shreveport.

Jan 3, 1914

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922

By J. G. Patchett, R. W. Rausch

Fresh waters and the presence of clay in many Rocky Mountain and West Coast sands require special methods of log analysis. Archie's saturation equation requires addition of a shale correction term, and the SP equation must also be modified to account for clays. Suitable equations were developed several years ago, but have not been widely used due to the algebraic complexity. A computer-oriented method has now been developed to overcome this problem. The basic shaly sand equations are rearranged in four different ways to permit solution for various sets of available input data. Essential to application of the method is the correction of observed SP values to those that would be observed if the resistivity of the formation waters were exactly interchangeable with the activity. A graphic method for doing this is given. Where conditions require consideration of the effect of clay in the sands, the method presented has been found to improve the accuracy of water-saturation determinations. INTRODUCTION Log interpretation in many Rocky Mountain and West Coast basins is complicated by rapid vertical and lateral changes in water resistivity. Calculation of formation water resistivity from the SP curve becomes difficult in zones that contain clay, since changes in SP deflection may be due to changes in either clay content or water salinity. In hydrocarbon-producing reservoirs, the problem is further complicated because hydrocarbon saturation also reduces the SP.1 A log interpretation system using computers has been developed to provide a solution to this problem, based on equations proposed by de Witte.2 Four different simultaneous solutions of de Witte's equations have been made. Each solution method uses a different set of input data as independent variables. Thus, a choice of solution method is possible, depending upon the logs run and the availability of other data. Two of the solutions do not require a knowledge of water resistivity. This system is intended to be used primarily in multiple sandstone-shale sequences of low and moderate resistivities where the principal contaminant in the sandstones is clay. However, where sufficient regional data are available, interpretation in single-zone sandstone reservoirs can also be improved by using the method. THEORY AND HISTORY OF SHALY SAND ANALYSIS The log interpretation formula originally proposed by Archie3 in 1941 is applicable only to rock-fluid systems wherein the rock has negligible electrical conductivity. In 1949, Patnode and Wyllie4 showed that if the rock itself can be considered conductive due to the presence of clay, a different calculation approach is necessary. During the following years, this problem was investigated at great length, as was the related problem of the effect of rock conductivity on the SP.5-11 These investigations established functional relationships between SP, resistivity, water saturation and water resistivity for such a formation. Refs. 2 and 12 provide summaries of these studies. Unfortunately, practical use of these relationships required that water resistivity be known independently from the SP. Although log interpretation methods for rock systems containing clay were proposed at that time,' they were not generally accepted for routine use. There are three principal reasons for this. First, in many field situations involving high-salinity water, rock conductivity may be neglected (even if present) without introducing appreciable error. This may be seen by considering the following expression for waier-saturated rock.' 1/R2=1/R1+1/FRn....(1) where 1/R, is conductivity due to clay. As Rw becomes small, I/FRw becomes much greater than 1/R, which may be neglected. Where 1/R, may be neglected, the sandstone is called clean. If the term may not be neglected, the sandstone is termed dirty or shaly. For resistivity purposes, the classification between clean and shaly sands then depends not only upon the conductivity due to shale in the sand, but also upon the resistivity of the associated water (shale is used here to mean surface condition due to disseminated clay). A sand of given conductivity might safely be treated as clean in association with high-salinity water, but would require shaly sand methods if associated with fresher waters. Shaly sand methods are not required in many areas having saline waters; but in Rocky Mountain and West Coast sands having relatively fresh waters (often more than 0.3 ohm-m resistivity at formation conditions), the shaly sand methods are needed. Errors Rw calculations from the SP due to the presence of shale are likewise related to water salinity. In saline water formations drilled with fresh mud, the ratio of mud filtrate resistivity to water resistivity is high, the SP is large and the presence of shale can introduce large errors in water resistivity calculated by the conventional method. When the resistivity ratio is low, the errors are smaller. At zero SP, no error would result from shale. Thus, from the SP viewpoint, a given rock could be shaly if associated with a saline water, and clean in association with a fresh water, which is the opposite of the resistivity-oriented definition above.

By George Mah, Charles Wert

Internal-friction peaks caused by diffusion of oxygen and nitrogen have been observed in ytterbium. They are thought to be caused by the redistribution, under stress, of strain dipoles around an interstitial oxygen or nitrogen and a neighboring substitutional impurity. With the use of a simple geometrical model, diffusion coefficients for oxygen and nitrogen between special interstitial sites have been calculated. a) APPLICATION OF INTERNAL FRICTION TO MEASUREMENT OF DIFFUSION RATES IN DISSOLVED INTERSTITIAL ATOMS In bcc metals, the interstitial atoms occupy the centers of cube faces (0, 1/2, 1/2), or their equivalents, the center of the cube edges (0, 0, 1/2). An interstitial atom in this position causes an aniso-tropic distortion in the lattice. When stress is applied, mechanical relaxation can take place by the movements of the interstitial atoms. This relaxation has been used to obtain information concerning the movements of the interstitial atoms in the bcc metals. Data for these alloys have been compiled by Stanley and Wert. Other researchers have extended the investigation of interstitial diffusion to the close-packed metals. Gupta and weinig2 found an oxygen peak in a titanium, the height of which is linearly dependent on the oxygen concentration. They assumed, therefore, that they were dealing with movement of atomic ally dispersed oxygen in titanium. KG and wang3 determined that the diffusion coefficients of carbon in fcc steels and in nickel obtained by internal-friction methods were consistent with those obtained by macrodiffusion methods at much higher temperatures. Bisogni found oxygen and nitrogen peaks in hafnium by use of which he deduced the diffusion coefficient of these gases in hafnium. He observed further that the half-widths of these peaks corresponded almost exactly with those of a single-relaxation process; he assumed it to be caused by movement of atomically dispersed oxygen and nitrogen. From these studies, the deduction can be drawn that, in general, diffusion data can also be obtained for the interstitial diffusion in close-packed metals (or more precisely, in slightly impure close-packed metals). One group of such metals for which little data exist for the diffusion of dissolved oxygen and nitrogen is the rare earths. They have great affinity for gases, which enter solution interstitially. In this investigation results were obtained for the Yb-O and Yb-N interstitial solid solutions with traces of substitutional impurities; these solid solutions are of fcc structure. b) MECHANISM OF THE RELAXATION IN FCC CRYSTALS In the fcc structure, an interstitial gas atom is usually situated in the octahedral position (1/2, 1/2,

Jan 1, 1964

By William P. Blake

Eureka has for several years past been known as one of the most important centres of production of argentiferous lead in the country. The average daily yield is now one hundred tons of lead bars, in which the silver and gold of the ore is concentrated. The value of this lead, called " bullion," is about $300 per ton. To produce this quantity of metal, about four times the weight of ore, or say four hundred tons, is required. Most of this ore is supplied by the two leading mines of the district, the " Eureka" and the " Richmond," adjoining claims on Ruby Hill, about two miles from Eureka. There are, however, many other mines from which considerable quan-

Jan 1, 1879

ALTHOUGH the open-hearth charge contributes CO, C02, H2, A and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion; the latter then is regarded simply as the source of the net heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were accomplished by blowing in air or oxygen, as in the bessemer converter, the net heat absorption would be negative; that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000 F (1600 to 1650 C), so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTING In a typical heat, the fuel furnishes about four million British thermal units per ton of steel produced. The heat required, for the metallurgical processes is not easily defined in useful manner but it ranges downward from about one million Btu, depending not only on the charge but on the manner of calculation. In, any event, this requirement appears. small in comparison with the

Jan 1, 1964

By N. J. Feola, E. P. Klier

NOTCH properties of titanium materials have been extensively investigated in the impact test.'-" For the most part the impact strength meas- ured suggests a ductile-brittle transition that lies at relatively high temperatures, thus indicating a possible notch sensitive condition at ambient temperatures. Recently it has been shown' that the impact strength for unalloyed titanium, as for aluminum alloys, may be a nonsensitive index of notch sensitivity as provided by the notch strength as measured in the notch tensile test. The notch strength for unalloyed titanium was found to depend on the nitrogen and carbon contamination levels. In the present work the levels to which oxygen, nitrogen, and carbon contaminants can be tolerated without leading to excessive em-

Jan 1, 1958

By William P. Blake

(Read at the Amenia Meeting, October, 1877.) EUREKA has for several years past been known as one of the most important centres of production of argentiferous lead in the country. The average daily yield is now one hundred tons of lead bars, in which the silver and gold of the ore is concentrated. The value of this lead, called "bullion," is about $300 per ton. To produce this quantity of metal, about four times the weight of ore, or say four hundred tons, is required. Most of this ore is supplied by the two leading mines of the district, the "Eureka" and the "Richmond," adjoining claims on Ruby Hill, about two miles from Eureka. There are, however, many other mines from which considerable quan-

Jan 1, 1878

By Stephen E. Erickson, Donald G. Oss

The need for instrumentation and automatic control of the various parameters in the heavy media process of iron ore beneficiation has been apparent for some time. Continued demands for higher grade, competitive products from the Mesabi Range have made it necessary to increase the efficiency of the process in every possible way. In a typical heavy media flow scheme for iron ore beneficiation (Fig. 1) a sized, prepared feed (generally about minus 1 ¼ in. to plus ¼ in.) is fed to a heavy media separatory vessel, along with a ferrosilicon slurry. A separation of the feed is made on the basis of specific gravity. Low density particles overflow a tailings discharge weir, while high density ore particles sink to the bottom of the high density pool and are moved away to the concentrate discharge chute.

Jan 5, 1962

By J. C. Motz

Introduction The variations in crushing plant design seen during the past 30 years provide a valuable source of information and experience from which one can select the optimum arrangement for a specific requirement. The purpose of this paper is to examine some specific equipment configurations as they relate to operating efficiency, plant availability and final product size in the form of mill feed. Due to the varied ore properties, physical space limitations, size of ore body and financial resources, there is no single crushing or grinding flowsheet that is best. Since energy costs have risen dramatically during the recent past, it became obvious that significant savings are possible by selecting equipment and a circuit which offers low power requirements balanced with low wear metal and installed equipment costs. Relatively clear and measurable are the metal and maintenance costs and the ever increasing cost of energy. Metal costs in the form of crusher liners have not quite doubled in the last 20 years, while power costs have increased by a factor of four or five, depending on the region considered. Estimates made only a few years ago on the increased cost of energy are obsolete in view of the recent unstable conditions. Since power is therefore becoming the largest cost area, it behooves us to investigate potential cost saving methods in the form of lowering the KWH/Ton of crude. Crushing To reduce run-of-mine to mill feed requires reduction in a series of stages. The physical size and power requirements of a crusher capable of reducing hard rock vary depending on the application. Extended experience in most crushing plants show that a minus 19MM (3/4 in.) rod mill feed can be and is being produced in three stages of crushing. In the majority of cases, the last crushing stage is closed circuited using anywhere from 19MM (3/4 in.) to 14MM (9/16 in.) slotted openings on the sizing deck. In some copper concentrators, the mill feed is all passing 13MM (1/2 in.) using three stages of crushing and 14MM (9/16 in.) square openings on the closed circuit screens. It was felt by some that crushing to this fine size is only possible if the ore is friable and is relatively soft in comparison to the harder ores. Our results show that some of the copper ores are as hard as taconite and are crush-

Jan 1, 1982

By Emile Rector Abadie

The picturesque little mining town of Grass Valley, nestled in the foothills of the Sierra Nevada mountains, at an altitude of 2500 feet, has been for 43 years the scene of uninterrupted activity and prosperity, as the center of a mining district which was intimately associated with the pioneer days of California, and the discovery of gold by James W. Marshall, in El Dorado county, in January, 1848. Although placer-mining was inaugurated in Nevada county as early as 1848, the first quartz ledge was not located until the summer of 1850. Discoveries made on Gold Hill and Massachusetts Hill increased the excitement in quartz-mining, and hastened the erection (during the same year) of the first mill operated in the State. At the close of 1864, the district had produced $23,000,000 in gold, and all the well-known properties of to-day had been discovered and worked. The Eureka-Idaho, the North Star, and the Empire mines were in active operation ; and to-day we still find them equipped with large crushing-plants, operating 80 per cent. of all the stamps in the immediate Grass Valley district. Of the mines just named, the North Star possesses the most recently constructed mill, a description of which, the writer believes, may prove of interest to members of the Institute engaged in the milling of goldores. During the year 1386, operations at the North Star mine (the property of the North Star Mining Company) had reached such a stage of development that the necessity of a crushing-plant at the mine became imperative, and early in October the erection of a 30stamp mill was in progress. The building designed to contain 40 stamps was speedily erected ; and within sixty days the large structure was under cover. Plate A represents the appearance of the mill 40 days after work was commenced. Late in February, 1887, the mill was in readiness, and, upon the

Jan 1, 1895

By R. W. Parsons

wben a displacement front encounters an isolated permeability heterogeneity, it will be perturbed. The details of this perturbation will depend on the beterogeneity size and shape, the Permeability contrast, and the mobility ratio. This paper deals with the displacement front behavior for one, simple, mathematically tractable model: a circular permeability discontinuity and unit mobility ratio. The progress of an initially planar front is shown for four permeability contrasts: k2/k1 = 0, 5/2, 2, m. The front distortion is more pronounced than streamline and isopotential distortion and it approaches a constant shape downstream from the discontinuity. INTRODUCTION The impact of reservoir heterogeneities on oil displacing processes depends upon the variation of the heterogeneous property (frequency distribution), its disposition (spatial distribution), and the inherent stability of the displacement mechanism.l The interplay of these factors plus the impracticability, if not impossibility, of describing a natural rock system in any detail makes exact displacement front movements difficult to determine. It is useful, however, to be able to qualitatively visualize what heterogeneities will do to a displacement front. In this respect certain simple models that can be treated analytically are of value. The following analysis will show the displacement front behavior for one such model. MODEL DESCRIPTION The flow field is two-dimensional and infinite in extent. The fluid flow is single phase, steady state and unidirectional at x, y = 2 m, or before insertion of the discontinuity. A circular permea- bility discontinuity is placed at the origin. Porosity and thickness are the same within and exterior to the heterogeneity. This is exactly the same model that was used by Greenkorn et al. to check analytically Streamlines as determined by Heie-Shaw flow models and finite difference computer techniques.2 FRONT POSITION CALCULATIONS The results of displacement front calculations are presented in Figs. 1 through 4 for four different permeability contrasts: k2/kl = O, %, 2, m. The times corresponding to the front locations are the Same for the 0 and cases! and for the 1/2 and 2 cases. The determination of front positions at various times is based on known analytical expressions for velocity potentials ().2 and stream functions ().2 These expressions are in terms of the x and y

Jan 1, 1969

By F. D. Rosi, Walter R. Hibbard, R. I. Herron, H. T. Clark, O&apos

Introduction and Previous Work In the search to find a copper-base alloy with high strength properties, it was considered that the addition of a small amount of an age-hardening element to a binary system with useful strength properties might result in a series of alloys of theeretical and practical importance. The copper-nickel system was selected for its basic properties and chromium was added as the age-hardening element in view of the small percentage involved and its decreasing solubility with decreasing temperature. A study of the Cu-Cr binary alloys was undertaken as a preliminary investigation. However, in view of the response of these alloys to heat treatment, the scope of this phase of the investigation was widened.

Jan 1, 1949

By Ben L. Seegmiller

Localized open pit slope failure was avoided as an apparent result of a practical rock mechanics program conducted at the Twin Buttes copper operation. The key to the program was the application of cable bolting, a technique that artificially supports open pit slopes using properly installed post-tensioned cables. As a result of the research and testing program, extensions of the cable bolting principal became significantly apparent. • The economics of artificial stabilization appear to be overwhelmingly favorable, and • Best practical applications are "final" pit slopes, slopes beneath permanent structures and potentially slope failing areas. Success of this research is manifested by the fact that similar stabilization systems are presently under consideration for Twin Buttes as well as other open pit operations.

Jan 12, 1974

By R. L. Wilcox, M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evaluated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1935

By N. J. Grant, K. M. Zwilsky

A series of copper-alumina dispersion strengthened alloys were prepared using three different copper and two different alumina powder sizes. Improvements in strength of up to ten times that of pure copper were found in room-temperature as well as elevated-temperature stress-rupture tests. Conductivity values remained from 70 to 90 pct that of pure copper. The best alloys were based on the finest metal powder (1 p) and contained from 7.5 to 10-0 vol pet of 0.018 or 0,033 p alumina. DISPERSION strengthening of metals consists of strengthening a metal matrix by the addition of oxides or other refractory constituents, followed by strain hardening, in order to reinforce the base material and extend its temperature range of application. Since the discovery of SAP by lrmannl and Von zeerleder2 in 1949, many investigators have reported data obtained on a variety of metal-inert oxide alloys.3-7 The present work deals with the mechanical mixing of copper and alumina powders. While several techniques of introducing the second phase have been investigated to date, mechanical mixing so far has been recognized as the simplest, least expensive, and most universally applicable technique that can be used to obtain an ultrafine dispersion of inert particles. In the present case, the effects of changing the metal particle size, the oxide particle size and the volume percent of oxide were investigated. This work is an extension of a previous study.6 EXPERIMENTAL PROCEDURE The starting materials were three different grades of copper powder and two different alumina powders. The three metallic powders were -74 µ(- 200 mesh) electrolytic copper powder consisting of irregular equiaxed particles having a normal screen distribution and analyzing 99.5 pct Cu, and two powders having a 5-µ and 1-µ particle size, average, respectively. The latter powders were produced by the hydrogen reduction of purified sulfate solutions at elevated temperature and pressure and were furnished by the Sherritt Gordon Mines, Ltd. The alumina used was obtained from Godfrey L. Cabot Co., under the trade name of Alon C, one batch of powder having a particle size of 0.018 µ, the other a particle size of 0.033 µ. The crystal structure of these alumina powders was found to be cubic gamma. Each batch of powder was mixed in a Waring Blendor for a total of 15 min, followed by a low-temperature reduction in hydrogen and vacuum compacting in cylinders which were hydrostatically pressed at 35,000 psi to give a compact that could be handled conveniently. Six of the compacts were hydrogen sintered at 900°C while the remaining four were sintered at 1000°C. Subsequently, all compacts were hot extruded at 760°C with a reduction of area ratio of approximately 20 to 1. Evaluation of alloys included density and resistivity measurements, room-temperature tensile tests, stress-rupture tests at 450°C plus one other temperature per alloy, hardness tests, microstruc-tural examination, X-ray analysis of the dispersed phase after dissolving the metal phase, and oxidation studies on two of the alloys. A vacuum-melted, wrought copper rod was tested together with these alloys for comparison purposes. RESULTS Table I is a summary of the compositions, sintering temperatures, densities and conductivity values of the ten alloys prepared. All alumina additions are given in volume percent, and will be referred to as

Jan 1, 1962

By B. H. G. Brady, C. M. St. John

Computational schemes for analysis of rock mass response to excavation, loading and other imposed changes, are employed pervasively in rock mechanics practice. Applications range in complexity from determination of stress and displacement distributions around openings, to prediction of the thermo-hydromechanical behaviour of a saturated fissured mass. While this may be taken as apparent sophistication in rock mechanics design activity, the indiscriminate use of computer methods may sometimes conceal inferior and inadequate engineering procedures. These inadequacies may not always be recognized, due to the general uncertainties which are inherent in rock mechanics investigations. This paper seeks to identify some common deficiencies in rock mechanics applications of computational schemes, and to propose ways of eliminating them. It also indicates some specific developments and applications of computational procedures, which are required to address persistent design problems in geomechanics practice.

Jan 1, 1982

By Roland D. Parks

CORUNDUM, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to our allies. Optical elements of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mohs' scale index of o, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent of this paper to deal only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. ORE PRODUCTION AND CONSUMPTION For the past two decades, South Africa has been the world's sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world's principal consumer of corundum ore; imports for the period 1934 through 1940 averaging 3000 short tons per year. The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the United States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918. Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912,

Jan 1, 1945