Search Documents

By David Kramer, Cecil G. Rhodes

Critical transport currents were measured as a function of perpendicular external magnetic field in Ti-22 at. pct Nb wire samples. These samples were heat-treated to yield w Phase precipitates at denslties ranging from 10 to 10 17cm-3. The Precipitates are ellipsoids of revolution with major axes of 50 to 1300A. Flux-Pinning by w precipitates is responsible for the high critical transport currents that were ob- ThE ability of a type II superconductor to sustain a zero-resistance transport current (Jc) in an external magnetic field (H) is due to the presence of micro-structural features which can impede the motion of magnetic flux penetrating the superconductor under the influence of a Lorentz force. Such features are referred to as pinning sites. The pinning strength is tained. A sample cooled from 800°C and annealed 1 hr at 450°C carried a critical tramport current of 10 amp per sq cm at 30 kG. Variations in the current-carrying ability of this alloy are due to changes in its pinning strength which is a function of precipitate density and composition and of the composition of the matrix. the reaction of the bulk superconductor to the Lorentz force and depends on the efficiency of the individual pinning sites and on their volume density. The super -current density increases with pinning strength, other things being equal. The above concepts are discussed in detail in a comprehensive review by Livingston and Schadler.' In Ti-Nb alloys, as in other binary titanium alloys, the metastable hexagonal w phase usually forms below the p/a + p phase boundary near the titanium side of the phase diagram. Stiegler et a1.' have summarized much of what is known about w phase in titanium and zirconium binary alloys. The present work deals with

Jan 1, 1968

By W. T. Lankford, Edward Saibel

During the course of an investigation of the plastic flow of aluminum aircraft sheet under combined loads, several problems arose in which analyses of the conditions leading to unstable plastic flow were needed. In order to provide these analyses, and in the hope of attaining a better understanding of the general problem of unstable plastic flow, the present study was undertaken. It is well known that unstable plastic flow is associated with a form of mechanical instabi!ity frequently observed during the plastic deformation of ductile metals. This instability is characterized by the fact that, at its onset, plastic straining mill proceed at a constant magnitude of the externally applied forces. It is further typical that the resulting unstable flow is generally accompanied by the formation of a neck, a local bulging, or some other form of heterogcneous deformation. Perhaps the most familiar example of unstable plastic flow to the metallurgist is the formation of the neck in the ordinary tension test. It is well known that in this test most metals exhibit a maximum in the externally applied load, followed by the process commonly referred to as "necking down." Instability in the simple tension test has been frequently discussed and numerous investigators1'2'3'12 have derived the criterion for instability in terms of a critical rate of strain hardening. It is the purpose of the present study to extend the criterion for unstable flow to the more general case where the body undergoing flow is subjected to combined loads. It is hoped that the problems considered will provide a more consistent picture of the general features of this important form of mechanical instability. The most practical implications of instability in plastic flow arise in connection with sheet metal forming operations. In the formation of a great many sheet metal parts, the deformations are produced primarily by stretching. If the conditions which lead to unstable flow are fulfilled in such a formation, and if the resultant instability leads to a pronounced localization of flow, then the useful limit of ductility of the material will have been reached. It i; also essential that the effects of instability be taken into consideration in any study of the plastic flow and rupture of metals under combined stresses. In general, when unstable plastic flow is initiated, straining becomes localized, the geometry of the test splecimen changes, and the state of stress in that portion of the specimen undergoing plastic flow is no longer under external control. In many past studies of the effects of combinetl Metals On flow and rupture) account has not been taken of the fact that, although a given test may be started under constant

Jan 1, 1947

By Edward Saibel, W. T. Lankford

During the course of an investigation of the plastic flow of aluminum aircraft sheet under combined loads, several problems arose in which analyses of the conditions leading to unstable plastic flow were needed. In order to provide these analyses, and in the hope of attaining a better understanding of the general problem of unstable plastic flow, the present study was undertaken. It is well known that unstable plastic flow is associated with a form of mechanical instabi!ity frequently observed during the plastic deformation of ductile metals. This instability is characterized by the fact that, at its onset, plastic straining mill proceed at a constant magnitude of the externally applied forces. It is further typical that the resulting unstable flow is generally accompanied by the formation of a neck, a local bulging, or some other form of heterogcneous deformation. Perhaps the most familiar example of unstable plastic flow to the metallurgist is the formation of the neck in the ordinary tension test. It is well known that in this test most metals exhibit a maximum in the externally applied load, followed by the process commonly referred to as "necking down." Instability in the simple tension test has been frequently discussed and numerous investigators1'2'3'12 have derived the criterion for instability in terms of a critical rate of strain hardening. It is the purpose of the present study to extend the criterion for unstable flow to the more general case where the body undergoing flow is subjected to combined loads. It is hoped that the problems considered will provide a more consistent picture of the general features of this important form of mechanical instability. The most practical implications of instability in plastic flow arise in connection with sheet metal forming operations. In the formation of a great many sheet metal parts, the deformations are produced primarily by stretching. If the conditions which lead to unstable flow are fulfilled in such a formation, and if the resultant instability leads to a pronounced localization of flow, then the useful limit of ductility of the material will have been reached. It i; also essential that the effects of instability be taken into consideration in any study of the plastic flow and rupture of metals under combined stresses. In general, when unstable plastic flow is initiated, straining becomes localized, the geometry of the test splecimen changes, and the state of stress in that portion of the specimen undergoing plastic flow is no longer under external control. In many past studies of the effects of combinetl Metals On flow and rupture) account has not been taken of the fact that, although a given test may be started under constant

Jan 1, 1947

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep uppermost the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance : 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1964

By R. A. Walker, R. G. Bradburn, B. C. Flintoff

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit testwork combined with an analysis of operating data showed that (1) metallurgical personnel at times could increase production rates by as much as 10% over that achieved by grinding operators; (2) the chosen data base required an increase of 2% or more to be statistically significant; and (3) for a 2% increase there would be a significant rate of return of investment in computer installation. Consequently one grinding circuit was fully instrumented, and a rented computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long-term objectives. The short-term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been successfully met as described in this paper. Statistically significant increases in excess of 2% have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long-term objectives are (1) off-line analysis of the circuit using mathematical models of process units; (2) on-line experiments to study alternative control tactics; and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1978

By J. M. Glass, C. D. Sholtess

We at Hughes Tool Co. are extremely proud of the quality of the hardware and techniques introduced through our efforts in tunnel-machine development and of the ready acceptance of them by manufacturers and contractors throughout the world. All of us who attended the conference and who are represented in the book, we believe, anticipate an increasing need for improved methods of underground excavation. The development of such methods will permit the further exploitation of our underground resources plus providing underground space for transportation and habitation at a rate compatible with demand. We hope that our comments, derived from the application of Hughes Tool Co.'s rotary boring experience, may provide a better understanding of the boring method as a possible avenue through which the desired improvement in underground excavation may be attained. We hope you may also become aware of some of the problems Hughes, as a pioneer developer of raise, shaft, and tunnel-boring equipment, must face prior to further major undertakings in this very interesting field. Our task is to acquaint you with the present status of the Hughes Tool Co. development program as it relates specifically to tunnel-boring machines. We feel this task can best be accomplished by a brief review of the general sequence of events leading to and constituting an equipment development program and more specifically the manner in which these events have occurred to either influence or further our boring-machine development program. The development of a machine to accomplish a certain function or series of functions is usually a very long and tedious process to which any number of individuals must contribute, perhaps over a period of centuries. Of particular irony is the fact that often those who contribute most generously do not necessarily reap the greatest immediate benefit. A marketable ma- chine will, however, result from a sequence of events such as these: 1) A problem or need is defined. 2) An idea is born to eliminate the problem.

Jan 1, 1970

By Charles Russell

PRESSURES developed by the coal during the coking process have been responsible for serious trouble to many companies that operate or build by-product coke ovens. The insidious nature of this trouble is indicated by the fact that oven operators, unless they have ascertained the charac-teristics of the coals they use, cannot determine the existence of dangerous pressures until after the damage has been done. A rather popular mis-conception is that ease of pushing of the charge at the completion of the coking period indicates that no dangerous pressure has been developed, but this is far from the truth; pressures developed during the coking period are often completely dissipated by the shrinkage of the charge in the completion of coking, and so any criterion based on the ease of pushing is futile. However, methods of testing coals are available that will definitely distinguish the dangerous coals from those that are safe, and such methods have been brought to a high degree of certainty. The operator should take no risk that involves either a lack of knowl-edge of the behavior of coals during coking or the failure to believe that certain of the coals or coal mixtures can cause damage to the oven struc-ture. This merely tends to minimize the problem and leads to claims that coking coals of all kinds may be carbonized with no danger of damage to the oven structure provided some particular kind of by-product oven is used. This lack of appreciation of the true situation is in itself one of the main factors leading to damage of coke-oven structures. Coals that develop more than a certain safe pressure cannot be used in by-product coke ovens without causing damage to the side flue walls. The following paper presents a highly certain method for the measure-ment of the pressures developed during the carbonization of coal-a method that is the culmination of many years of work on the problem in which a number of methods for the purpose were investigated and used. While actual pressures found may appear to be small when expressed in pounds per square inch, the number of square inches in each oven wall is so large that the total pressure on the oven wall becomes an enormous load.

Jan 1, 1939

By R. G. Ward, P. L. Sachdev

Using an improved maximum bubble pressure technique, the densities of iron silicates at 1400°C have been measured under nitrogen. At the wiistite composition the density has been measured by bubble-blowing experments with both argon and nitrogen and calculated from the measured volume of a known mass of melt under nitrogen. The densities under nitrogen are significantly different from those measured under argon for melts containing less than 28 wt pct SiO2. THE constitution of liquid slags is not well understood, largely because no single property or parameter can be measured which gives conclusive evi- dence of the types and packing of the ions present. Of the many property measurements which can provide information leading to a picture of the constitution of slags, density gives the most direct evidence and has been studied extensively. The work reported here is part of a program of study of densities in multicomponent melts in which the iron oxide-silica system is the solvent. These melts are important as they are fundamental to basic steelmaking, and they allow the study of basic silicate compositions which have hitherto been largely neglected. As considerable disparity exists

Jan 1, 1965

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1941 are available at Institute headquarters, unless otherwise noted They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS TECHNICAL PUBLICATIONS in Classes A-Metal Mining, 13-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysics, are issued as separate pamphlets An Institute member is entitled to one copy of any printed TECHNICAL PUBLICATION or CONTRIBUTION Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute according to their registration by classes CONTRIBUTIONS and other TECHNICAL PUBLICATIONS will be sent upon request A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page, minimum charge, 25¢ Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1 25 domestic, $1 35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2 50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7 80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers) MINING TECHNOLOGY, $6 per annum domestic, $6 60 foreign (metal mining, milling and concentration, Industrial Minerals Division, and mining geology papers) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6 60 foreign Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY Is mailed each month A member is entitled to one volume a year on his membership and he may purchase for $2 50 one copy of a volume not already received, additional copies of the same volume, $5 Nonmembers in the United States may purchase the volumes listed at $5 each, outside of the United States and its possessions, $5 6o Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 500 each to members, to nonmembers 50¢ current issue and $1 each, back issues Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4 00 foreign.

Jan 1, 1941

By William Lodding

Muscovite was the crystalline material used in the experiments discussed in this paper. It was both wet and dry ground for various periods of time. The effects (physical and chemical changes) produced in grinding are analyzed by use of thermal analysis. That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Mackenziel and Bartha2 reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding and, on the other hand, existing strain may be released by the same process, as shown by Holt, et a1.3 All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze, by the use of thermal analysis, some effects produced in grinding. In differential thermal analysis (DTA) one measures the sum of all thermal changes occurring in a substance during heating or cooling; e.g., chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and thermal conductivity, strain release, etc. By thermogravimetric analysis (TGA), on the other hand, only chemical changes involving weight loss or gain are recorded. Similarly, gas evolution analysis (GEA) will register only reactions involving gas evolution. By performing two or all three of these methods of thermal analysis simultaneously and on the same specimen, one can separate the different effects registered and, by difference, evaluate their magnitude. The results of TGA are usually plotted as percent weight against furnace temp. When one differentiates weight against furnace temp, a rate of weight-change curve is obtained, and the resulting differential thermogravimetric (DTG) plots are similar in appearance to DTA thermograms for the same reaction. While the integrated area under a DTA peak represents enthalpy and can be expressed in calories per gram the area under the corresponding DTG peak represents the weight change which took place during a reaction. The similarity of DTA and DTG thermograms obtained from one material can be seen in Figs. 1 and 2. EXPERIMENTAL A Fisher mortar grinder and a porcelain mill with burundum balls were used for both dry and wet grinding. Muscovite was first carefully hand-filed and screened on 20 and 100 mesh. The middle fraction was considered essentially unaltered muscovite.

Jan 1, 1968

By H. E. Nold

THE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained.1 For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. PERIODIC KILNS Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues through-out the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1933

By J. Donald Graham, John G. Kuhn

The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an ore body, no more and no less. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. The method for controlling development drilling programs to be described was developed during the latter part of a major development drilling project at the Christmas mine of Inspiration Consolidated Copper Co. in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous ore bodies of the porphyry-copper type would be the most likely candidates for application of the technique. Discontinuous ore bodies would not be amenable. The method is based on the measurement of the linear correlation between the spatial distribution of two sets

Jan 1, 1973

By H. D. Hodges, J. K. Godbey

In order to better understand the fracturing process, bottom-hole pressures were measured during a number of typical fracturing operations. A recently developed system was used that allows simultaneous surface recording of both the bottom-hole and wellhead pressures on the same chart. The results from six fracruring treatments are summarized on the basis of the pressure data obtained. Al-though no complete analysis is attempted, the value of accurate pressure measurements is emphasized. Important characteristics of the bottom-hole pressure record do not appear at the wellhead because of the damping effect of the fluid-filled column. In four of the six treatments described, the formations apparently fractured during the initial surge of pressure with only crude oil in the well. The properties of the fluids used during the treatments are given and the fluid friction losses are obtained directly from the pressure records. This technique is also shown to be adequate for determining when various fluids, used during the process, enter the formation. INTRODUCTION Hydraulic fracturing for the purpose of increasing well productivity is now accepted in many areas as a regular completion and workover practice. Numerous articles have appeared in the literature discussing the various techniques and theories of hydraulic fracturing'. In general, three basic types of formation fractures are recognized today. These are the horizontal fracture, the vertical fracture, and fractures along natural planes of weakness in the formation'. Any one or all three of these fracture types may be present in a fracturing operation. However, with only the wellhead pressure record as a guide, it is difficult at best to determine if the formation actually fractured, and is almost impossible to determine the type of fracture induced. These difficulties arise in part because the wellhead pressure record, especially when fracturing through tubing, does not accurately reflect the pressure variations occurring at the formation. Several factors contribute to this effect and preclude the possibility of using the wellhead pressure as a basis for accurately calculating the bottom-hole pressure. These factors are: 1. The compressibilities of the fluids which damp the pressure variations. 2. The changes in the densities of the fluids or apparent densities of the sand-laden fluids. 3. The flowing friction of the various fluids and mixtures, which is dependent on the flow rates and the condition of the tubing, casing, or wellbore. 4. The non-Newtonian characteristics of a sand-oil mixture and its dependence upon the fluid properties, the concentration of sand, and the mesh size used. 5. The unknown and variable temperatures throughout the fluid column. Because of these reasons it was determined that in order to obtain a more accurate knowledge of the nature of fracturing, the bottom-hole pressure must be measured along with the pressure at the surface during a fracturing treatment. Even with accurate pressure data, a reliable estimate of the nature of fracturing is still dependent upon knowledge of the tectonic conditions. However, the hydraulic pressure on the formation is basic to any approach to a complete analysis. In order to accomplish this objective a system was developed to record the wellhead and bottom-hole pressures simultaneously at the surface. By recording both pressures on a dual pen strip-chart recorder, it was possible to greatly expand the time scale so that rapid pressure variations would be faithfully recorded. By such simultaneous recording, time discrepancies inherent in separate records are eliminated, thus overcoming one of the most difficult problems associated with bottom-hole recording systems. This paper illustrates the results obtained by using this system during six typical fracturing operations. All of these tests were taken in wells that were treated through tubing. By a direct comparison of the wellhead and bottom-hole pressures, the importance of obtaining complete pressure information during a fracturing treatment is emphasized. THE INSTRUMENTATION AND PROCEDURES The bottom-hole pressure measuring instrument consisted of a pressure-sensing element, a telemetering section, and a lead-filled weight or sinker bar. The pressure-sensing element used was an isoelastic Amerada pressure-gauge element. By using an isoelastic element, no temperature compensation was necessary in the tests described, since the temperature was believed to be well below the maximum temperature limit of 270°F. The rotary output shaft of this helical Bourdon tube element was coupled to a precision miniature potentiometer. The rotation of the pressure-gauge shaft thus changed the resistance presented by the potentiometer

By W. B. Tijmann

Maintaining safe, yet economical, slope geometries in a mining operation is paramount. When design analysis and engineering judgement have dictated conservative and usually more expensive problem solutions, monitoring has often proven to be a valuable method in dealing with potential slope instability. A well planned and executed monitoring program can allow operation at a lower theoretical margin of safety. Monitoring provides a valuable check on design parameters and can measure effects of remedial improvements. Warning of impending failure can often be established well in advance. The monitoring problem situations in civil engineering works and open pit mining are much alike. Instruments used for monitoring in both industries are often the same. In this paper, geotechnical instruments for measuring deformation and groundwater pressure in rock and overburden are discussed with a broad-brush approach. Results obtained over extended time periods are presented in a graphical presentation for a case history. Descriptions of various types of instruments, mostly used to monitor stability of rock slopes, are discussed, and data analysis and approximate costs are presented.

Jan 1, 1983

By Walter Barnum

AS a member of the Institute and as the president of the National Coal Association, I come before you today in a dual role. As an Institute mem-ber I welcome the opportunity to make complimentary reference to the growing support which bituminous coal operators are giving to programs looking to the advancement of the engineering profession, and to suggest plans whereby these programs may be enlarged to mutual advantage. As a representative of the bitu-minous industry, it gives me special pleasure to express the appreciation of the industry for the services ren-dered to it by members of your profession. Needless to say, there is a close relationship between the engineer and the coal operator. With increasing frequency and in the interests of the industry, the engineer is becoming more of a factor in the business of producing coal. I need look no further for an out-standing example of this encouraging trend than to Samuel A. Taylor, who not only is a bituminous coal producer but also has risen to such eminence in the engineering profession as to have been chosen the head of this great body of technical men, the American Institute of Mining and Metallurgical Engineers. There are many coal operators whom I might mention as having achieved distinction in the engineering world, such as Howard. N. Eavenson, chairman of the .Coal and Coke Committee. And I would be guilty of a serious .oversight if I failed to make reference to Eckley B. Coxe, one of the founders of the Institute in 1871, a prominent anthracite operator and credited with several important inventions. While it is true that a. considerable number of execu-tives of coal-producing companies in this country came up through the engineering ranks. the proportion of mine executives in England, France, and Germany who are graduate engineers is much larger than it is in the United States. In France all members of the staff are engineers and such is the case in Germany up to the owner of the mine. In Germany the owner is not so frequently an engineer as is the rule in France.

Jan 3, 1927

By J. L. Huiatt, G. M. Potter, R. B. Tippin

The US Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. have developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 6% K2O. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgS0, 2.7Hp0) and schoenite KeS0,MgS04.6H,0), were conditioned in a saturated brine solution., thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular-weight fatty acid. Continuous small-scale pilot-plant testing indicated that 80% of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 13% K2O.

Jan 1, 1976

By D. L. McCain

Slurry transportation of coarse coal from the mining face to the preparation plant has proved successful in a West Virginia underground mine. Coal has been pumped from the mining section for several months. The system is currently being provided with the flexible link to the face to allow for continuous transportation. Some future plans for coal mines and projections for broader applications of the transportation method are given.

Jan 1, 1976

By F. E. Pawlek, J. K. Gerlach

The chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. In the first part of the investigations the reaction rate of the chlorides of sodium or calcium with gas mixtures of SO,-0, or SO ,-O2 ,-SO , was measured. The rate for reactions with gas mixtures SO2-O2 is ThE chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. At present the process is mainly applied to produce nonferrous metals which occur in pyrite cinders in small concentrations. Thereby the nonferrous metals are converted into water-soluble, acid-soluble, or volatile compounds whereas all the iron remains as insoluble oxide. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. The reactions occurring during the roasting process can be divided into two groups: solid-solid reaction and gas-solid reaction. The reactions between solids proceed by means of solid-state diffusion and are therefore of low velocity. The heterogeneous reactions between solids and gases of the roasting atmosphere5 are high-velocity processes and determine the velocity of the chloridizing roasting. These gas-solid reactions shall be the subject of the paper presented. In order to investigate the still little-known processes which occur during the chloridizing roasting 6-' the complex reaction is split into several partial steps. First the reactions of NaCl and CaCl, with gas mixtures of SO2 and 0, have been investigated at temperatures between 500" and 600°C by measuring the weight increase of the samples. The gas mixtures used in this series of experiments had first variable compositions, then the amount of SO 2 had been increased. Furthermore the influence of Fe 2 O3 admixtures upon these reactions, the behavior of pure Fe 2 O3 with the gaseous reactants, and the chlorination of the sulfides of lead, copper, nickel, and zinc have been investigated. FORMATION OF GASEOUS CHLORINE Pyrite cinders are never completely roasted and therefore contain still a small amount of sulfide sulfur. When heated again in air, this sulfur is converted into SO,. Accordingly the formation of chlorine can first be described by the reactions: dependent on the composition of the gas phase. If more than 1 pct SO 3 is added to the roasting gas, the reaction rate is determined only by the concentrations of the SO,. In the second part the reactions between chlorine and metal sulfides are discussed. The rate of formation of gaseous chlorine is higher by me order of magnitude than is the reaction rate between ZnS and chlorine. The reaction rate of NiS and PbS lies considerably below that of ZnS. The conversion rate of both pure Fe 2 O 3 and Fe 2 O 3 containing NaCl or CaCl2 when reacting with SO2-O2, mixtures with and without SO3 portions was measured at temperatures of 500", 550°, and 600°C. The weight increase of pressings was determined by means of a spiral balanceg and the reaction rate calculated therefrom according to Eqs. [ll to [31 and [5] to [7]. The prepared samples were suspended on a platinum filament in a vertically mounted tube of mullite (ID 4 cm, length 110 cm) which could be heated by a resistance tube furnace. The platinum filament was tied to the lower end of the spiral balance. A supremax glass tube (length 70 cm) was mounted gas-tight on top of the reaction tube. The unit was sealed up at its top by a ground-in stopper which was holding the spiral balance with the sample. The spiral balance therefore hung outside the high-temperature region of the furnace. Fig. 2 shows the experimental arrangement schematically. While lowering the sample into the reaction tube pure nitrogen was flowing through the reaction zone providing a protective atmosphere. After the sample had reached the reaction temperature within approximately 1 min, the protective gas was replaced by the sulfur dioxide-oxygen reaction mixture. It took about 30 sec until the mixture filled the tube homogeneously. A Ni/NiCr thermocouple placed in the center of the furnace where the sample hung during the measure-

Jan 1, 1968

By David B. Burrows, Rlkl Kobayashi, Norman L. Carr

The viscosity of hydrocarbon mixtures, whether in the gas or liquid phase, is a function of pressure, temperature, and phase composition. This paper presents methods for the prediction of the viscosity of the gas or less dense fluid phase over the practical range of pressure, temperature, and phase compositions encountered in surface and subsurface petroleum production operations. The correlation necessary to predict the effect of pressure on viscosities is presented in Part I. Serious discrepancies in high pressure gas viscosity data in the literature are discussed. The application of the correlation to predict absolute viscosities is discussed in Part 11. Auxiliary correlations are presented to enable calculations of viscosities from a knowledge of the pressure, temperature, and gravity of the gas phase. INTRODUCTION A knowledge of the viscosity of hydrocarbon fluids is needed to study the dynamical or flow behavior of these mixtures through pipes, porous media, or more generally wherever transport of momentum occurs in fluid motion. Since flow is predominantly in the laminar region in petroleum reservoirs, the influence of fluid viscosity on this flow is especially important. As early as 1894, Onnes1 and Onnes and de Haas' noted that the viscosities of homologs under corresponding states could be correlated. The theorem of corresponding states has been further developed and applied to the viscosity of pure, nonpolar gases under pressure by Comings, Mayland, and Egly.3 It was demonstrated that the viscosity ratio could be expressed rather closely as a function of reduced pressures and temperatures, 1.e.: µ/µ1 = f( TR2 PR) ........(1) temperature, absolute units where: TR =------------------------------ ------ critical temperature. absolute units _pressure, absolute units critical pressure, absolute units µ = viscosity of gas at reduced temperature TR and reduced pressure PR µ1 =. viscosity of gas at atmospheric pressure and at temperature TR Serious discrepancies in the viscosity of pure hydrocarbon gases at high pressures have been called to Our attention by Comings, and and Egly. They made a careful analysis of the following methods commonly used to measure gas viscosities: 1. Oscillating disc viscometer4,5 2. Rolling ball viscometer6,7 3. Capillary tube viscometer12 On the basis of their analysis of the problem and their experimental data on the viscosities of methane, ethylene, carbon dioxide, and propane, they preferentially selected data obtained by the capillary tube viscometer to develop their viscosity correlation. Since then a need has existed to verify the experimental technique of Comings, Mayland, and Egly for the determination of viscosities at high pressure; to extend the data to mixtures of hydrocarbons; and to extend the range of their correlation to include higher pressures. Using the correlation procedure of Comings, May-land, and Egly, the prediction of gas viscosities is resolved into the correlation of the effect of pressure, temperature, and composition on the viscosity of hydrocarbons and their mixtures and the prediction of viscosities of mixtures of hydrocarbons and other natural gas components at one atmosphere pressure.

Jan 1, 1955

By S. Mukai, Y. Shah, T. Zshikawa, T. Wakamtsu

In order to recover coal concentrate of low ash and low iron content, the electrostatic separation of coal was studied. It is more successful in the corona discharge field to recover the coal concentrate of low ash and low iron content than in the field without corona discharge. The effect of humidity on the electrostatic separation of coal was then studied. From the experimental results, it was clear that the electrostatic separation was excellent in about 60% relative humidity of atmosphere. Thus, the separation of vitrite from coal is practicable by electrostatic separation. In recent years the demand for high quality coal containing low ash, low iron, and low sulfur has increased. To fulfill this requirement, a higher grade coal concentrate must be produced. Study on the electrostatic separation of coal has been performed for several years in the author's laboratory. From the results of this research, it was considered that the behavior of coal particles in the electrostatic field relates closely to the ash and iron content in coal. In the present paper, the electrostatic separation of coal in corona discharge field was studied in order to recover the high quality coal concentrate and then the effect of humidity on the electrostatic separation was investigated. PREPARATION OF COAL SAMPLES The coals from the Akabira mine, the Kushiro mine, the Miike mine, and the Oshima mine which are famous coal mines in Japan were used in this study. The ash contents of these coals are shown in Table I. From the results of the analysis of the coal samples by the Norelco X-ray diffractometer, it is recognized that the Miike coal includes mainly pyrite, quartz, kaoline, calcite, and epidote; the Kushiro coal: kaoline, quartz, and montmorillonite, and the Oshima coal: siderite, dolomite, and other substances. For the preparation of samples, the coarse pieces of coal were crushed to about 2 mm in diam and then ground in an agator mortar. The ground products were sieved and fractions of 10 — 14 mesh, 14 — 20 mesh, 20-28 mesh, and 28-35 mesh were prepared, respectively. APPARATUS OF ELECTROSTATIC SEPARATION The principal part of the apparatus of the electrostatic separation used in the experiments is shown in Fig. 1. In order to generate the corona discharge field, a needle-shaped electrode combined with a pole electrode is installed as the high tension electrode. In the case of investigating the effects of the humidity on the electrostatic separation of coal, the needle-shaped electrode was combined with a plate electrode instead of the pole electrode as shown in Fig. 2. The pole or the plate electrode was installed to promote the repelling of the charged particles by producing the electrostatic field between this electrode and the grounded roller. It seems to be very useful on the coal separation to install these combined high tension electrodes. SEPARATION OF COAL PARTICLES IN CORONA DISCHARGE FIELD The separation testings on the coal samples in the corona discharge field were performed by the apparatus as shown in Fig. 1. These experiments were carried out under the following conditions: feed size 20 — 28 mesh, room temperature, normal humidity and applied voltage 15-20 KV, and the combined electrodes including the needle-shaped electrode were negatively charged. The results of these testings are

Jan 1, 1968