Search Documents

By D. T. Farnham

The shale used at the Renton plant of the Denny-Renton Clay and Coal Co. for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated.

Jan 1, 1915

By J. R. Eckel

It has long been known that mud properties affect drilling rate and that drilling with water is as much as six to .seven times faster than with mud. However, it is not known why drilling rates with mud are lower. Recent studies show what fluid properties govern microbit drilling rate and also provide a quantitative correlation of these fluid properties and hydraulics with microbit drilling rate. All the microbit tests reported in this paper were made with a low permeability (about 10 md) limestone. They were conducted at constant bit weight and rotary speed with varying fluid properties, flow rate Q and nozzle dinnteter d. The tests showed that (1) drilling rate in a given system with constant circulating rate and nozzle velocity is a function of the kinematic viscosity [viscosity /density, (cp)/ p (density)] of the drilling fluid measured at near bit nozzle shear rates; (2) the combined effect of fluid properties and hydraulics on microbit drilling rate is defined by a Reynolds number function (kQp/dp); (3) for the same kinematic viscosity, drilling rate is independent of solids content; and (4) for the same kinematic viscosity, drilling rate is independent of fluid loss. INTRODUCTION The fact that mudding up reduces rate of penetration is well known, but the reduction varies from well to well. The rate with mud may be 80 percent of the water rate or it may be as low as 15 percent. Since this reduction of up to seven-fold takes place under conditions of constant bit weight, rotary speed and mud circulating rate in a uniform formation, it can only be a result of the change in fluid properties. Previous work1-" both in field tests and in laboratory microbit tests) showed that drilling rate with mud is lower than with water (Figs. 1 and 2). Microbit tests also confirm, at least qualitatively, the field observation that drilling rate slows with increased pressure differential from borehole to formation (Fig. 3). The qualitative effect of drilling rate of bit weight, rotary speed and rate of mud circulation are also the same for the field and microbit rig. For these reasons, the industry generally accepts microbit results as being qualitatively meaningful in terms of field application.

By Frank Van Horn

IT is customary to ascribe two general modes of occurrence to natural gas, namely shale. gas which, as the name indicates, is found in' shale, and reservoir gas, which occurs ill sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts.

Jan 1, 1917

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to be- gin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTLIRES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, de- pending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1964

By Robert W. Metcalf

THE name "tripoli" is used to designate a number of more or less similar types of silica of sedimentary origin. Usually they are spoken of as "soft" silicas, and are light, very fine grained, porous, and friable. Structure is microcrystalline or cryptocrystalline. The deposits are the residual product of weathering and occur in massive form, either blocky or in friable masses. Tripoli is the end product of the weathering of siliceous Limestones, cherty limestones, or cherts. Weathering removes the calcium carbon- ate, leaving a finely divided siliceous residue to which the name "tripoli" has been applied. Authorities differ as to whether the chert accumulates first and is converted into tripoli or the tripoli is derived by direct decay from various forms of silica during initial weathering of the Limestone. It has also been asserted that tripolis were formed in situ in essentially their present condition as a flocculent, colloidal silica, but it is now believed by most geologists that varying degrees of pressure, combined with one or more methods of origin, have influenced the characteristics of the deposits. Considerable confusion has existed as to what constitutes tripoli. Owing to the similarity of names, tripolite, a type of diatomaceous earth found originally in Tripoli in northern Africa, has been erroneously called tripoli. Tripoli, however, contains no diatoms, the distinguishing characteristic of diatomaceous earth. The material mined in the Missouri-Oklahoma area has been considered by the trade to be the type material, and many feel that the term "tripoli" should more properly be restricted to the product of this region. Although also designated as soft silica, it would be less misleading, perhaps, if the siliceous material mined in southern Illinois were called amorphous silica. Both the Missouri-Oklahoma and Illinois materials are very high in silica. Different in composition, as it is very much lower in silica content than tripoli or amorphous silica, yet included under the classification of tripoli in Bureau of Mines statistical data, is the small but important output of rottenstone in Lycoming County, Pennsylvania. The principal justification for grouping these three types of silica is similarity of use.

Jan 1, 1949

By G. G. Waddell, T. J. Crocker, S. S. M. Chan

A successful engineering structural design often depends upon a thorough understanding of the material properties of the structure. It is no exception when designing a supporting system for stable underground openings. For this reason, studies were made in the deep mines of the Coeur d'Alene mining district to obtain engineering properties of rocks and rock masses immediately surrounding underground openings. In this paper, data concerning laboratory tested physical properties of rocks and in-situ deformation behavior of rock masses from the Galena, Lucky Friday, and Silver Summit mines of the district are presented. Interpretations of the data so obtained and suggestions for the use of the results of the investigations as design criteria are also outlined.

Jan 1, 1973

By Robert E. Cuthbertson

IT is the purpose of this paper to describe in detail the laboratory development and mill application of an unusual combination of flotation reagents employed in the concentrator of the Climax Molybdenum Co., on the Continental Divide, near Leadville, Lake County, Colorado. This development originated in an ore-dressing research laboratory maintained by Climax at the experimental plant of the Colorado School of Mines, which is staffed by men directly employed by the Climax Molybdenum Co. Mill-scale testing of laboratory developments was supervised by a representative from the testing laboratory, working in close cooperation with the operating staff at the mill. General milling practice at Climax is ably described in a paper by E. J. Duggan,1 mill superintendent. Other aspects of the Climax project have been described in papers by W. J. Coulter,2 by Butler, Vanderwilt and Henderson3 by Allen Kissock,4 and by Leo H. Glanville.5 Consequently, this paper will be confined to the metallurgical aspects of recent reagent developments, avoiding, as much as possible, repetition of material covered in these earlier publications. BRIEF HISTORY OF REAGENT PRACTICE AT CLIMAX Prior to the year 1937, the only reagents employed at Climax for froth production and collecting action in the flotation of molybdenite were steam-distilled or destructively distilled pine oils. The only exceptions to this practice were brief periods of mill testing, when reagents of various types were tried on an experimental basis. None of these experimental runs was sufficiently encouraging to justify its continuation as regular practice. Sodium, cyanide has been employed since the very early days of milling at Climax as an inhibiting agent for control of pyrite and chalcopyrite. Alkaline reagents such as lime or soda ash have been used in recent years to minimize the detrimental effect of iron salts on flotation of molybdenite. The presence of these harmful salts is attributed to the decomposition of fine metallics abraded from liners and balls in the first stage of regrinding rougher concentrate. Flint pebbles are used in subsequent regrinding, since alkaline reagents are not entirely adequate to offset the inhibiting effect of iron salts as the grind becomes progressively finer and the grade of concentrate progressively higher. Climax metallurgists were familiar at an early date with the use of petroleum products such as kerosene and gas oil as promoters of flotation of molybdenite. Charles C. Oliver6 discussed the use of pine oil and kerosene as early as 1920, in connection with the milling practice at Dominion Molybdenite Co., Quebec. Never theless, the early attempts to apply this knowledge in the Climax concentrator were complete failures. In the light of recent experience, it may seem strange that the early mill tests with petroleum

Jan 1, 1944

By Frank Peterson

THE manufacture of gasoline by extraction or precipitation from the natural gases in which it is found, the present status of. the industry, its past development and future extensions; offer a subject which is so broad that to handle it in its entirety would require a voluminous paper. The writer will, therefore, attempt to concentrate the essential matter of the subject for a general presentation, giving some of the most interesting details of the factors that are important to the industry. This industry has drawn liberally on the principles of physics and chemistry, and, to a large extent, has had to adapt such information as is most useful-not from data recorded with reference to petroleum, but from data recorded with reference to general treatment of other materials. Because of the complex character of the petroleum series of hydro-carbons and the fact that data, such as solubilities, vapor pressures, etc., of the different petroleum compounds have not been determined, we are still working by rule of thumb in. some essential phases of the industry. Furthermore, the difficulties of determining such data are almost insurmountable. We have not one,, but two butanes to deal with-not one, but several, pentanes, hexanes, heptanes, and, as we ascend in the series the complexity and multiplication of isomers increases at such a rate as to make the task of isolating and studying their physical characteristics almost beyond the hope of possible attainment. The industry is the connecting link knitting the interests of oil producers and refiners into a much closer relationship than ever existed .prior to its inception and development. The relation between the producer and the refiner of petroleum prior to 1910 was. a rather antagonistic one in a commercial sense. It was to the interest of the producer of crude petroleum to sell it for a maximum consideration; the refiner's interest was to obtain the same product for a minimum consideration; therefore, each side of the business transaction retained within his own hands as far as possible the trade secrets of his business. Each side maintained an attitude of cold-blooded business sympathy only for the other. Cas-

Jan 12, 1917

By James B. Vance, Parviz Mottahed

An extensive research program has been carried out at PCS Mining for some time into the use of high frequency microseismic emissions in the range of 30-200 kHz for roof fall warning in the mines. A laboratory investigation on loaded samples of potash has established a close correlation between acoustic emissions and the applied load. The tests also indicated the occurrence of the Kaiser effect. The positive and encouraging response from underground testing and controlled laboratory testing has lead to the extension of the investigation into correlation of the high frequency microseismic emissions and the change in stress distribution due to mining. Hydraulic borehole pressure cells were installed at different depths ahead of the advancing boring machine. The output due to the stress change and the microseismic event count was monitored by a continuous chart recorder. This paper discusses the results of this instrumentation. The results confirm the strong correlation between the two measured parameters and outlines future areas of research for the use of the high frequency microseismic emission techniques in quantifying the changes in stress distribution.

Jan 1, 1984

By J. Halpern, D. R. McKay

SOME of the most important hydrometallurgical developments in recent years relate to processes involving the oxidation of sulfide minerals in aque- ous suspension at elevated temperatures by air or oxygen under pressure. Among these is the acid pressure-leach process which has been developed, particularly for the treatment of pyritic uranium ores.1-5 In this process, an aqueous suspension of the ore is digested in an autoclave, in which an overpressure of air or oxygen is maintained, at temperatures above 100°C. Oxidation of the pyrite (FeS,)

Jan 1, 1959

HAVING produced one ton of concentrate that contains the copper that can profitably be saved or recovered from anywhere between 3 and 60 tons of mine ore, the ore-dressing engineer passes the result of his handiwork over to the metallurgist for smelting. Essentially, the concentrate is a damp mass of finely ground material consisting of copper sulphide minerals; pyrite, the sulphide of iron; and gangue, usually silica and silicates of aluminum. The purpose of smelting is to produce metallic copper and a slag containing the iron and siliceous constituents by pyrometallurgy-the kind of metallurgy that employs fire and heat to produce the chemical reactions through which it attains its object. Though blast furnaces have been used to smelt Porphyry-mine concentrates, notably at Braden, more than 90 per cent of [ ]

Jan 1, 1933

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system.

Jan 1, 1941

By J. Szekely, Robert G. Lee

Calculations are presented for the prediction of the combined radiative-convective heat loss from molten steel held in a ladle, covered by initially molten slag. A mathematical formulation is given and numerical solutions are presented of the resultant partial differential equation. It is shown that a slag layer of about 2 to 3 in. thick would prevent any significant heat loss from the top metal surface for Periods of up to 1 hr. For thinner slag layers (or in the absence of the protective slag) appreciable heat losses would occur; plots given in the paper allow the quantitative evaluation of the fall in the metal temperature due to this heat loss. The ironmaking-steel processing operation involves several intermediate steps where the molten metal is held or transfered in ladles. The quantitative assessment of the heat losses occurring under these conditions is of considerable importance in process design considerations since the temperature of the metal may have to meet rigid specifications in any given part of the processing sequence. While the metal is held in a ladle, heat is lost by two mechanisms: i) by conduction into the ladle walls; ii) by radiation and convection from the top surface. Calculations relating to the conductive heat loss, are readily made and information may be found in the literature both on data pertaining to metallurgical situations and on the techniques that are available for performing additional computations.'-3 The evaluation of the combined convective-radiative heat loss is less straightforward, especially when there exists a protective slag layer covering the metal. In this latter case, as the top slag surface loses heat partial solidification may occur and the latent heat thus given up by the slag may represent an effective barrier to the heat loss from the metal. A semiquantitative assessment of the role played by the slag in preventing heat loss from the metal has been made in a previous paper,4 where it was shown that a slag layer 6 in. thick would act as a near-perfect insulator for periods of up to 2 hr. However, this first paper reported on an essentially preliminary investigation that considered only one slag layer thickness; furthermore, the boundary conditions used for the calculations were somewhat restrictive since no allowance was made for changes in the metal temperature. The purpose of this second paper is to extend the scope of the preliminary investigation previously reported by: i) considering several slag layer thicknesses; ii) allowing for variations in the metal temperature; and finally iii) by performing calculations on the net loss from the metal rather than from the slag surface. FORMULATION Consider a slag phase extending from y = 0 to y = L1, covering a metal phase that occupies the region extending from y = Ll to y = L, as illustrated in Fig. 1. Denote the slag and metal temperatures by TS and Tm and assume that initially both slag and metal are molten, having a uniform temperature Ti. At time = zero the surface represented by the y = 0 plane (top slag surface) is brought into contact with cold air, the temperature of which is given as T Thus for time > zero, heat will be transfered from the slag to the air by natural convection and thermal radiation; as a result of this heat loss the slag temperature will fall and after some time a solid phase is formed and a solidification boundary (more realistically described as a zone) will move progressively from y = 0 toward y = L1. Once the region of temperature gradients, moving ahead of the solidification zone, reach the slag-metal interface (y = L1) there will be a net transfer of heat from the metal through the slag to the cold air, across the y = 0 plane. In the formulation of moving boundary problems, involving phase changes that require computer solution, it is convenient to represent both phases by a single equation, making allowance for the latent heat of solidification by assigning an appropriate temperature dependence to the specific heat content. Thus the energy equation for the whole of the slag may be written as follows:

Jan 1, 1969

By E. H. Jr. Dix

OF all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations had been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 5.25° C. to about 1 per cent. at 300° C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540° C., and that this amount decreases to about 3 per cent. at 20° C.

Jan 2, 1926

By William A. Kennedy, Jonathan R. Stahl

This paper deals with the phenomenon of water held in a leach dump due to capillarity. Water is shown to be retained in the fine pores of the ore as well as in the interstices between the rock and soil particles. Upon drainage, Chino leach dump material shows two distinct capillary systems and a double capillary curve is often obtained. Both the igneous and the sedimentary rocks composing the leach material are shown to have appreciable porosity but little permeability. Fluid flow is, therefore, restricted to the interstices between the rock and soil particles. The irreducible water saturation for the aggregate is found to be 884 for the -48 mesh material and 235 for the448 mesh to one inch material. The composite sample of minus one inch dump material had an irreducible water saturation of 52 percent. The irreducible water saturation in the fine pores of the ore was found to be between 73 and 76 percent. Very coarse pores or channels between large rocks exhibit essentially zero capillary retained water. The presence of fine material in a dump can cause high water saturations to be retained and these saturations may be mistaken for perched water tables. Perched water tables can be drained but capillary water will be retained. Capillary pressure data can aid in distinguishing between perched water tables and capillary retained water.

Jan 1, 1974

By F. O. Blackwell

It is roughly estimated that some three hundred companies in the United States engaged in mining and the kindred arts now employ electricity in their operations. As all these plants have been installed within the last few years, it is evident that mining engineers have been quick to appreciate the great advantages of the use of electricity and adopt it for their many requirements. In

Jan 1, 1894

By J. W. Craig, H. L. Walker

Industry has for many years recognized the dependence of certain mechanical and physical properties. as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. Literature A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing. The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbsl has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered. Townsend and Greena112 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1949

By L. J. M. Smits

A theoretical equation is developed describing membrane potentials of shaly sands as a function of the cation-exchange capacity per unit pore volume of the rock and saturating water salinity. This equation is based on the same simple physical model as that employed earlier7 describing the electrical conductivity of shaly sands. Experiments conducted with NaCl solutions showed that the equation is obeyed, except in the case of saturated salt solutions where minor deviations were observed. A possible explanation is given for this discrepancy. As the clay content and the porosity of shales may vary appreciably, shale membrane potentials also vary. It was found that membrane potentials of shales can be calculated accurately with the aid of the same theory. Consequently, changes in membrane potentials can be accounted for by simple measurement of cation-exchange capacities per unit pore volume of both shales and shaly sands. Charts are given to facilitate interpretation of the electrochemical part of the SP in terms of cation-exchange capacities and the salinities of mud filtrate and formation water. INTRODUCTION A spontaneous potential (SP) log is a record of the way in which the electrical potential of a sonde varies as it passes down a borehole. Such variations frequently reflect rock texture, e.g., permeable beds intercalated in an impermeable series often are indicated by a sharp change in potential. Nowadays it is recognized that SP logs may be interpreted in terms of formation-water salinity and formation shaliness. The four sources of the SP are illustrated in Fig. 1. El and E4 represent streaming potentials generated by the flow of mud filtrate through mud cake opposite permeable formations and through shale, respectively. An extensive review of the literature on the evaluation of these streaming potentials is given by Lynchl and will not be discussed here. The remaining part of the SP generally is called the electrochemical potential, which is divided into two parts: a membrane potential across the shale (E3, Fig. 1) and a membrane potential in the permeable sand at the diffusion boundary between formation water and mud filtrate (E2, Fig. 1). It was found by wyllie2 that the membrane potential across the shale, E3, is the most important contribution to the electrochemical potential, the shale acting as a semi permeable membrane. When the sand is clean it does not influence the diffusion process, so E2 equals the value of the so-called liquid-liquid junction potential observed when the two solutions diffuse freely into each other. When the sand contains clay, however, this interferes with the diffusion process and affects the diffusion potential generated. The greater the proportion of clay, the stronger this effect will be. Wyllie,3 Doll4 and Poupon et al.5 took this effect into account theoretically, starting from a physical

Jan 1, 1969

By Eugene A. Stephenson

Critical analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,' Pierce and LewisI2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by Mc Williams.4 Much of the dissatisfaction with proration in certain fields arises because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the " potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If no difficulties ever developed in drilling, shutting off water, or in well completion, it might

Jan 1, 1931

By D. B. Dowling

(San Francisco Meeting, September, 1915) THE interest which has been aroused in prospecting for oil in the foot hills of southern Alberta, and in the oil possibilities of the known gas fields situated in the less-disturbed areas, called for a much closer examination of the structure, thickness, and composition of the underlying rocks of the region than had -hitherto been made. The areal geology of the larger part of the great plains was outlined by Dawson, McConnell, and Tyrrell, between 1881 and 1885. The foothill area was not critically examined at that time, owing to the time which would have been required for its proper study and the difficulty that was found in recognizing in the foothills the divisions which had been adopted in the mapping of the formations of the plains. This was clue in great measure to the paucity of exposures in continuous sections of the lower divisions of the Upper Cretaceous. Since the pioneer work on the plains was published, the beds which form continuations south into Montana have been critically examined. The Canadian beds arch over the end of a flat anticline which rises to the south; and two sections in Montana, one on each side of the anticline, help to explain some of the difficulties previously encountered in the mapping of the measures found in the foothills. The index map, Fig. 1, shows the area studied, and its relation to southeastern Alberta, and to Montana.

Jan 6, 1915