Search Documents

By Cyril Stanley Smith, W. Earl Lindlief

A study of the mechanical properties of the alloys of copper and silver led to the discovery that the solubility of silver in copper was greatly different from that generally supposed, therefore some work was done to determine the solubility with greater accuracy than had previously been achieved. After the work had been completed, two papers were published' giving solubility figures which agreed closely with one another and with the work described herein. A detailed comparison of that work with the present will be given later. Preparation of Allots The copper used in making the alloys was electrolytic ingot of high purity. The silver was prepared by precipitation as chloride from nitric acid solution, followed by fusion of the washed precipitate with sodium carbonate and potassium nitrate. This method gives metal containing at least 99.99 per cent silver. The copper was first melted under charcoal in a small electric resistance furnace and the silver added as pure silver, it being unnecessary to make any intermediate alloys. After thorough stirring the metal was poured into a mold of suitable form. The alloys contained between 0.008 and 0.015 per cent of oxygen. Small amounts of oxide were visible under the microscope, but it is not believed this would have much effect on the results. Copper-silver alloys are notorious for segregation, consequently a few experiments were carried out to find a form of casting with as little segregation as possible. A mold 6 in. long and 1/2-in. dia. was first used, and an alloy nominally containing 5 per cent silver was cast in it, while some of the same alloy was poured directly into water to obtain the maximum rate of cooling possible. Analyses were made both on this sample and on turnings from the top and bottom of the 1/2 in. dia. cast-ing, the turnings being separated into three parts according to the position

Jan 1, 1932

By J. E. Burke, C. S. Barrett

THE fine lines shown in Fig 1 are typical of markings that may be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied to them, such as deformation lines or strain markings, indicate this uncertainty. In this paper which reports the results of a further investigation of their nature, they will be called strain markings. INTRODUCTION Matthewson and Phillips1 in 1916 concluded that strain markings appeared only after deformations that exceeded 20 pct. They objected to the markings being called slip lines believing this term should be reserved for surface markings produced by plastic deformation. In 1921, Vogel2 described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallographic in nature, and since they resemble Neumann bands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matthewson3 reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as evidence that the markings coalesce into annealing twins, and hence that they themselves are mechanical twins. Many attempts have been made to [ ] demonstrate directly that the markings are mechanical twins. In 1934, Samans4 described the results of X ray studies of two deformed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings are mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5,6,7 although in no case was the original method of Samans employed. An

Jan 1, 1948

By R. S. Dean. J. R. Long T. R. Graham, Roberson A. H., Armantrout C. E.

The general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing ro to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heuslerl recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and 10 per cent A1 but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 has drawn a hypothetical boundary for the alpha field with few, data to support such construction. The binary systems involved have rcceived considerable attention by numerous investigators, and their general features are well established. The copper-ahminum system (Fig. I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smith6 established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig' ') has been recently reviewed by Dean and CO-WorkersS.7 Using high-purity alloys,

Jan 1, 1947

By Armantrout C. E., R. S. Dean. J. R. Long T. R. Graham, Roberson A. H.

The general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing ro to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heuslerl recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and 10 per cent A1 but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 has drawn a hypothetical boundary for the alpha field with few, data to support such construction. The binary systems involved have rcceived considerable attention by numerous investigators, and their general features are well established. The copper-ahminum system (Fig. I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smith6 established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig' ') has been recently reviewed by Dean and CO-WorkersS.7 Using high-purity alloys,

Jan 1, 1947

By H. G. Kok

The continuous increase in energy costs has made it necessary to consider a broader use of belt conveyors for the transportation of material from the mine pit to the processing plant. Hard rock has to be crushed before it can be moved by belt conveyors. Systems are in the planning stage for mining hard rock, such as copper and iron ore, by using high-capacity, mobile, or semi-portable crushers. The mobile crusher is located in the pit, and the crushed material is transported by energy-efficient, shiftable belt conveyors out of the pit.

Jan 1, 1983

INTRODUCTION TO SAMPLING THEORY Before specifically discussing mineral sampling and sampling procedures, let us briefly consider broader and more universal concepts of modem sampling theory. A sample is de- fined as a representative part or a single item from a larger whole, being drawn for purpose of inspection or shown as evidence of quality. In modem theory the sample is a part of a statistical population whose properties are studied to gain information about the whole. The theory of sampling is built around the concept that if enough representative units of a larger overall population are selected without bias, the average value of the units will approximate that of the total population. Modem theory attempts to answer the question of how many samples are enough, given certain limits and constraints, and seeks to apply methods of sample selection and of estimation that provide, at the lowest possible cost, estimates that are precise enough for the purposes at issue. In order to meet these objectives the designer of a sample survey must rely heavily upon statistical theory. Statistics has been defined as the collection, presentation, analysis, and interpretation of numerical data. Statistical methods are primarily concerned with making valid inferences about a population based upon samples taken from the population. For most statistical applications, the total sample is in terms of number of items, attributes, or things; whereas mineral samples are usually in terms of weight or volume of mineral particles. Certain steps are involved in a well designed sample survey without regard to the particular field of application. Because the desired characteristics of an unmined mineral deposit can- not be known other than by sampling, we will consider these principle steps in terms of a mineral sample survey: 1) Clear definition of the objectives of the survey. In the case of mineral sampling this step is so apparent as to be almost ridiculous. However, it is surprising how often the overall objective of a sampling program is overlooked when decisions are made on a day-today basis. 2) Definition of the population to be sampled. The word population is used to designate the aggregate from which the sample is chosen. A sampling program may be designed to determine the grade of a single stope within a mine, the grade of a particular zone within a complex ore body, or the total value and extent of a mineral deposit. Since mineral sampling is usually done in phases, it is well to

Jan 1, 1980

By A. C. Fieldner

ASH in coal has always been regarded as an undesirable substance, as the heat content of a coal decreases in direct proportion to its ash content. It represents so much inert material that has to be transported, handled when the coal is burned, and finally disposed of. W. R. Roberts, in an address before the Engineers' Society of Western Pennsylvania, Pittsburgh, on Sept. 29, 1925, said that on an annual output of five hundred million tons of coal, a reduction of 3 per cent. of ash means fifteen million tons of refuse and a decrease of $30,000,000 in freight charges. Ash also often prevents efficient utilization of the coal through the formation of clinker caused by the melting of the ash constituents when subjected to heat. The mineral constituents of coal may be of such nature as to make the coal unsuited for specific uses, as for instance, high-sulfur coal for making metallurgical coke. While the usual proximate analysis of coal gives the amount of ash, it gives no information as to the nature and composition of the ash nor of the mineral constituents from which the ash is produced. For the efficient washing of coal to remove ash-forming constituents it is desirable to know the composition and distribution of the ash-forming constituents. Obviously such information is also desirable for the most efficient utilization of coal.

Jan 1, 1926

By B. Paul, C. C. Fu

Experiments indicate that the fatigue limit of various drill steels becomes vanishingly small in the presence of water and other corrosive liquids. Therefore one must generally expect fatigue failures of drill steels in a great many field operations. However, it is theoretically possible to so choose the hammer impact speed of a percussion drill in order to maximize the total length of hole drilled before failure occurs. In this paper the existence of an optimum speed is demonstrated and it is shown to be comparable to presently used piston speeds. The influence on drilling speed and hole length of a number of other pertinent design features, such as bit geometry, hammer geometry and steel properties is also established. Although machinery should be designed to obtain optimum performance, it is not always clear just what performance characteristic is to be optimized. For example in a rock drill it would be desirable to optimize all of the following characteristics: drilling speed, bit life, steel life, total length of hole drilled before failure, and efficiency of energy conversion. The word failure could signify excessive bit wear, bit fracture, steel fracture, or some other type of component failure. It is not possible in general to optimize all performance criteria simultaneously. For example, one could achieve fantastically large drilling rates at the expense of bit or steel life, energy requirements and physical size of system. It therefore becomes necessary to compromise requirements in order to achieve a well-balanced albeit non-optimum design. It is, however, extremely useful to explore the interrelationships between the different performance characteristics. Such a procedure would help to establish theoretical limits of performance within the framework of existing knowledge and also serve as a practical design procedure for special applications where a particular performance characteristic is of greatest concern to the user (e.g., steel breakage might be especially undesirable in certain locations). It is the purpose of this paper to examine the problem of how one may drill the deepest possible hole before breakage of the drill steel occurs. Of course the problem is almost trivial if a well defined fatigue limit (endurance limit) exists for the drill steel. In such cases one merely keeps the piston impact speed sufficiently low to insure that the stresses in the steel never exceed the fatigue limit, thereby achieving an infinite life. If, however, no definite fatigue limit exists, as seems to be the case in the presence of even mildly corrosive agents such as water (see later discussion), then a finite life is inescapable and one can at best hope to maximize the useful life of the system. Indeed it will be shown that the system life is related to drilling speed in the manner shown schematically in Fig. 1-a. Even if a definite fatigue

Jan 1, 1965

By Frederik P. Agterberg

This paper deals with frequency distributions in the field of mineral resource evaluation when a grid is superimposed on the study area and metallogenetically significant attributes are coded with respect to the cells of the grid. It is shown that the parameters of a negative binomial distribution for frequency of mineral deposits per cell can be derived from the parameters of a gamma distribution for the coded attributes. It is also shown that an exponential model for spatial correlation of cell values and Matheron's discrete Gaussian model for indirect transfer functions may provide a suitable methodology for relating cell value distribution to cell size.

Jan 1, 1977

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By A. P. Herring, M. Hoover, D. W. Fuerstenau

The dissolution of nickel, copper, and cobalt from five different samples of well-characterized deep sea manganese nodules was measured as a function of temperature, pH, leaching time, and particle size. Nickel, copper, and cobalt extraction each respond to these variables in a different manner. The results of this investigation indicate that copper and nickel can be selectively dissolved from iron and manganese at moderately low pH, provided the reaction is given sufficient time. A high dissolution of cobalt with dilute sulfuric acid can only be achieved from nodules that have a low iron content (<5%). The most probable rate-controlling step for copper and cobalt dissolution is diffusion through the pores of the nodules, and for nickel dissolution chemical reaction appears to be rate-controlling.

Jan 1, 1974

By Henry P. Ehrlinger, James C. Bradbury

Tripoli is a naturally occurring, very finely divided form of silica found chiefly in some midwestern and southeastern states and used commercially as fillers and abrasives. Definitions Tripoli is a microcrystalline, finely particulate, more or less friable form of silica that appears to be the product of leaching of siliceous limestone or calcareous chert. The term was originally applied to a deposit near Seneca, Mo., that resembled material of that name found near Tripoli in North Africa (Hovey, 1894). The two deposits were subsequently found to have different physical characteristics -the North African tripoli, now called tripolite, is a diatomite, composed of the siliceous skeletons of microscopic marine plants called diatoms, and the Missouri tripoli contains no diatom remains; the term tripoli, however, continued to be used for the Missouri material and is now applied in a general way to most silica deposits similar to it in characteristics and geologic origin. In commercial trade tripoli is commonly understood to designate material from the Missouri-Oklahoma field; silica from southern Illinois, the other major producing area, is referred to commercially as amorphous silica. Each term, however, may be used commercially for material, regardless of place of origin, that has the characteristics or uses commonly ascribed to the material from one or the other major producing area. For example, in the commodity price listings, Engineering and Mining Journal routinely lists under Tripoli, prices "f.0.b. Elco, III." and "f.0.b. Seneca, Mo., and Rogers, Ark.," and under Silica, amorphous, prices "f .o.b. Ill.," and "f .o.b. Dierks, Ark." Amorphous silica, the commercial designation given to southern Illinois tripoli, is, like the term tripoli, a misnomer. Mineralogically, the southern Illinois deposits are composed of microcrystalline quartz, and no amorphous material has been detected during X-ray and scanning electron microscope investigations (Leamnson, Thomas, and Ehrlinger, 1969; Thomas et al., 1970). Soft silica is another term that has been applied to Illinois and Tennessee tripoli, presumably to distinguish it from the more compact Missouri material. It has also been used in the ceramic trade to distinguish tripoli from "hard" silica, or silica flour, produced by pulverizing silica sand (Heinz, 1937). Rottenstone, produced commercially in Pennsylvania, is similar to tripoli in that a major constituent is finely particulate silica, and its uses are much the same as those of tripoli- as abrasives and fillers. The origin of rottenstone also is similar to that of tripoli-decomposition of a siliceous sedimentary rock. The parent rock is defined as a siliceous limestone (Gary, McAfee, and Wolf, 1972; Thrush, 1968) or as shale (personal communication). Heinz (1937) quotes a brief statement describ-

Jan 1, 1975

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying tip pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By Lloyd R. Jackson

In the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: 1. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalized strains in determining the effect of plastic flow on the work-hardening of metals. FundamentalS Involved in Plastic Flow In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Nevertheless, as will be shown, metals are close enough &apos;0 being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables—six being stress variables, and six being strain variables. From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses and one for strains) that have received most attention are the following: q2 = ½[(Txx= - Tyy)2 + (Tyy - Tzz)2 + (Tzz - Txx)2 + 3(Txy2 + Tyz2 + 7xx2) [1]

Jan 1, 1947

By Thomas Fraser, H. F. Yancey

PRIOR to the war just ended, Germany was the greatest coal producer in continental Europe. In 1943 the production of coal, bituminous and higher in rank, together with brown coal calculated to the equivalent amount of bituminous coal, is estimated to have been about 240 million metric tons, according to the War Department. Before the war production in Germany exceeded consumption. No other country in continental Europe except Poland had a large surplus. However, England&apos;s surplus was the largest in Europe as a whole. Before World War II the Ruhr Basin normally supplied about 70 pct of the total production of high-rank coal, the Saar and Aachen about 6 pct each, Upper Silesia about 14 pct, and Silesia and Saxony the remainder. Nearly one third of the brown coal was produced in the Rhineland, a little less than one half in central Germany west of the Elbe River, and about one fourth east of the Elbe. Bituminous coal and brown coal together constituted by far the most important energy resources of the old German Reich. Bituminous coal furnished nearly 70 pct of the total energy requirement, brown coal supplied about 25 pct, and water power, wood, petroleum and alcohol together aggregated only 7 pct. Because it was the most important single mineral resource of Germany, an excess of coal enabled the Reich to import nearly all the other mineral products that she lacked, such as iron ore from Lorraine. The area adjacent to the coal fields was supplied with gas from an interconnected grid. Similar electric grids are based on brown coal with the power stations at the mines. Coal tar provided the foundation for the development of the extensive German chemical industries as exemplified by the I. G. Farbenindustrie. For almost a century, German scientists have been adequately supported both by the State and by industry in studying improved methods of utilizing coal. In Germany the mineral rights were reserved by the State and ordered extraction of coal was enforced. Each lease comprised a relatively extensive area, which accounts for the generally large size of the mines and mining companies. In 1938 there were 160 mines in the Ruhr, with a total output of 125 million tons but go pct of the production was controlled by 20 companies. By far the largest single coal-mining company in Germany was the Gelsenkirchener Bergwerke A. G., which produced nearly 27 million tons in the Ruhr in 1937. Second was Saargruben A. G., a State-owned company operating in the Saar, which produced more than 13 million tons. Third was Bergwerksgesellschaft Hibernia A. G., with 10 million tons, also in the Ruhr. Briquettes are made from both bituminous coal and brown coal, but in 1938

Jan 1, 1946

By Lloyd R. Jackson

In the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: 1. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalized strains in determining the effect of plastic flow on the work-hardening of metals. FundamentalS Involved in Plastic Flow In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Nevertheless, as will be shown, metals are close enough &apos;0 being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables—six being stress variables, and six being strain variables. From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses and one for strains) that have received most attention are the following: q2 = ½[(Txx= - Tyy)2 + (Tyy - Tzz)2 + (Tzz - Txx)2 + 3(Txy2 + Tyz2 + 7xx2) [1]

Jan 1, 1947

By L. K. Oliver, Marshall

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By Marshall, L. K. Oliver

The use of model studies for the development of invasion patterns for cycling is .illustrated by model studies obtained with a recently developed apparatus in the solution of actual cycling problems. Introduction Depletion of a gas reservoir by cycling under pressure maintenance may be divided into three general phases. In the first phase, injection of dry gas is used to move all possible wet gas to producing wells prior to breakthrough of appreciable quantities of dry gas into producing wells. In the second phase, injection moves additional wet gas to producing wells while moderate quantities of dry gas are being produced. The third phase consists of production without injection to deplete the commercial gas reserve which remains after the cycling operation. Thus, in the first phase, a portion of the reservoir is invaded by dry gas, and the dry gas usually displaces something less than 100 pct of the wet gas from the invaded portions of the reservoir. The second phase enlarges the invaded portion of the reservoir and, at the same time, increases recovery from that zone invaded by dry gas in the first phase of the cycling operation. The result is an early yield of a substantial quantity of the liquefiable hydrocarbons in the reservoir with a minimum of the retrograde losses which occur in some reservoirs. The overall recovery from such an operation is usually high. The summation of the paths taken by dry gas in a cycling operation can be termed an invasion pattern. The use of electrical models to predict invasion patterns has been the subject of several contributions to the literature.1-3 The results of such model studies as applied to actual cases has been discussed by Kelton4 and Miller and Lents.= Recently, an improved apparatus for conducting potentiometric model studies has been developed, as described by Lee.V he purpose of this paper is to present model studies or invasion patterns obtained with this instrument in the solution of actual cycling problems. The percentage of displacement of wet gas within the invaded portion of the reservoir in cycling, increase in recoveries of wet gas by continuing cycling after dry gas breakthrough, recoveries of wet and dry gas by production after cycling, or economic factors in cycling are beyond the scope of this paper. Discussions which follow will be limited entirely to the development of suitable invasion patterns for cycling under pressure maintenance and the use of model studies therein. Discussion OF Results In using model studies to predict invasion patterns in cycling, some factors which influence the results are the following:

Jan 1, 1948

By John W. Brauns, David H. Orr

9.1-1. Description and Basic Function. A conventional railroad haulage system for a surface mine performs the function of transporting the ore and/or waste out of the pit to a crushing plant or dump. Trains consisting of a locomotive and gondola or side-dump care suitable for loading by power shovels are used. Gondola cars are restricted to hauling ore as a rotary dumper is required to unload them. Side-dump cars are more versa- tile, being satisfactory for carrying both ore and waste; but because of their additional dumping mechanism they are likely to be more expensive to maintain (12). Also they weigh up to two times as much as a flat-bottom car of the same capacity, and, therefore, fewer cars can be hauled per train. Standard-gauge track is most commonly used. Track systems incorporate temporary track of low quality in areas where moves are frequent and permanent track of high quality on main lines. Rail haulage enabled open pit mining to establish its reputation, for efficiency. Prior to World War II it was the principal type of transportation used in large pits. Other successful surface mine haulage methods have been developed since that time. These have served to supplement railroad transportation, permitting selection of a method that is best adapted to the peculiar requirements of each mining project. 9.1-2. General Applicability and Controlling Physical Conditions. For handling rough rock, the shovel-train system is unexcelled (6). The ideal application is in a physically large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transported than will any other haulage method. Relatively gentle

Jan 1, 1968