Search Documents

Since its organization, in July, 1917, the War Minerals Committee of the Institute, of which William Y. Westervelt is chairman, has been studying important phases of the mineral industry and its relation to winning the war. From this has come a realization of the imperative need for more definite coordination than is possible without direction by some governmental agency. No privately controlled industry can have the detailed knowledge of war needs or the control of all its supplies and markets necessary to effect the adjustment of its activities for war purposes. Inevitable shortages of certain essential minerals confront us unless immediate steps are taken to stimulate and develop. the mining

Jan 2, 1918

By A. C. Losekamp, J. B. Conway

Thermal-expansion data for, tungsten, rhenium, tantalum, .molybdenum, niobium, W-25 pct Re, Ta-10 pct W, ant1 Mo-50 pct Re are presented covering the range from room tempature to 2500°C. In these measureMents, made in a resistively heated tungsten tube furnace operating in a helium atmosphere, data for rod and sheet specimens were found to be identical; in addition, arc-cast and sintered tungsten were found to yield essentially identical results. Optical rneasurenlents of thermal expansion .made in any atmosphere other- than vacuum are subject to a refraction error which can be quite substantial. Specimens tested in helium appear shorter than when tested in racuum and hence a special correction factor must be applied to the helium data in order to obtain accurate results. WHILE it is true that linear thermal-expansion data for many of the refractory metals have been measured to very high temperatures, it is also true that except in a few instances the data from various investigators are not in good agreement. This is particularly evident in the case of tantalum and niobium although some tungsten data have been reported which differ by as much as 40 pct from the data of other investigators. Due to the sensitivity of both tantalum and niobium with respect to impurity absorption during exposure to high temperatures, it is probable that this single factor accounts for the majority of the discrepancies in the thermal-expansion data for these metals. However, this same factor can probably not be employed to explain the existing differences in the tungsten data. In all probability, these are due to errors in the measurement technique, to material composition variations, or to changes which take place in the material during the heating process (e.g., additional densifica-tion resulting from heating a sintered specimen above the original sintering temperature). In view of the discrepancies which exist in the linear expansion data reported for many of the refractory metals, the current study was initiated in an attempt to resolve such differences. Also, no high-temperature linear thermal-expansion data were found to be available for several refractory metals. Providing such data was another objective of the current investigation. MATERIALS In this study test specimens were employed in either rod or sheet form and in several instances both arc-cast and sintered material were employed. Material compositions are presented in Table I. Helium gas was fed to the furnace at a rate of about 0.5 SCFH and no special purification procedures were employed. However, the helium contained less than 50

Jan 1, 1967

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

By J. L. Craig, C. L. Edwards, M. D. Harper, J. M. Ray

The Los Alamos National Laboratory executed 19 intermediate scale cratering experiments in oil shale at the Colony Mine in Garfield County, Colorado. These experiments have led to a better under- standing of fracture characteristics and fragmentation of & - oil shale by use of a conventional high explosive. Geologic site characterization included detailed mapping, coring, and sample analyses. Site-specific geology was observed to be a major influence on the resulting crater geometry. The joint patterns at the experimental site frequently defined the final crater symmetry. Secondary influences included vugs, lithology changes, and grade fluctuations in the local stratigraphy. Most experiments, in both the rib and floor, were conducted to obtain data to investigate the fragmentation results within the craters. The rubble was screened for fragment- size distributions. Geologic features in proximity to the explosive charge had minimal effect on the rubble due to the overpowering effect of the detonation. However, these same features became more influential on the fracture and rubble characteristics with greater distances from the shothole. Postshot cores revealed a direct relationship between the grade of the oil shale and its susceptibility to fracturing. The Colony Mine experiments have demonstrated the significant role of geology in high explosive/oil shale interaction. It is probable that this role will have to be considered for larger applications to blast patterns and potential problems in retort stability in the future of oil shale development.

Jan 1, 1983

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941

By J. H. Moran, E. E. Finklea

The pressure build-up technique is a recognized method of determining permeability from conventional drillstem tests. In this paper an effort is made to extend such techniques to the interpretation of data obtained from the wireline formation tester. Such a study is necessary because of the differences, for this case, in the magnitude of the flow parameters (rate of flow, amount of recovered fluids) and in the flow geometry (flow through a perforation vs flow across the face of the wellbore, etc.) involved in the solution of the equations of flow for compressible fluids. The perforation is replaced by a spherical hole, and the effect of the borehole is neglected, so that the flow can be considered to be radial in a spherical co-ordinate system. Arguments are presented to justify this idealization. Assuming single-phase flow, general relations between pressure and flow rate are developed for a homogeneous medium. The study is then extended to permeable beds of finite thickness. It is shown that the early stages of pressure build-up tend towards spherical flow, while the later stages tend towards cylindrical flow. The thinner the bed, the more quickly flow approaches the cylindrical model. The prevalence of thin beds in practical work makes this analysis quite important. Cases involving permeability anisotropy are treated. INTRODUCTION From wireline formation tester operation, two types of data are obtained: (1) the nature and amount of recovered fluids, and (2) the pressure history recorded during the test. A number of papers have been written dealing with the interpretation of formation production on the basis of the recovered fluids.'.' In general, the methods described have been quite accurate for both high- and low-permeability formations. The present paper will deal with an analysis of the pressures observed. An analysis of the pressure build-up curves obtained in hard-rock country has already been attempted on the basis of the formula proposed by Hor-ner. Although this approach has met with success in many instances, some questions have been raised as to its validity. It is the aim of the present study to place the analysis of pressure build-up in the formation tester on a firmer basis, from which more detailed methods of interpretation can evolve. Because of the great differences between the operation of the wireline formation tester and the conventional drillstem test, modifications are necessary in the interpretation. The major difference relates to the flow geometry. Once the flow geometry has been established other features such as multiphase flow, skin effect, afterflow, etc., well described in the literature, can be introduced. It will be assumed that the mechanical operation of the formation tester is already known to the reader.6 t will suffice here merely to state that the tester provides the means for taking a relatively small sample of the fluid immediately adjacent to the borehole, and for recording the subsequent pressure response. In comparison with conventional drillstem tests, the time required for a satisfactory pressure build-up response is much shorter, because of the relatively small quantity of fluid withdrawn by the wireline tester. This feature is highly desirable in the case of low-permeability formations. For an analysis of the pressure response within the formation, three simple flow geometries are considered— linear, cylindrical and spherical. The spherical and cylindrical flow geometries are most pertinent to the formation tester; therefore, they will receive the major emphasis. Since the configuration of the borehole and the perforation made by the tester complicate the flow geometry, it is necessary to allow for them in the drawdown response. However, because of the volume of formations contributing to the pressure-response, the details of the perforation shape are unimportant in the build-up period. Since relatively small amounts of fluid are withdrawn from the formation, in contrast to a conventional drill-stem test, a study of the "depth of investigation" and the significance of drawdown as well as build-up data will be included. Because the "depth of investigation" will be shown to be rather large, the effect on the build-up curves of the finite thickness of the permeable bed is considered. It is this consideration that leads to the importance of cylindrical flow geometry. Also included is a discussion of permeability anisotropy and its effect on the interpretation of the tester results. The pressure curves recorded by the formation tester will follow two general patterns, depending upon whether the formation is of high or low permeability. Fig. I (a and b) schematically illustrates these two responses. In Fig. 1(a), the high pressure recorded during fill-up of the tool is essentially the pressure differential across the choke in the system. In Fig. l(b), the flow rate is

By J. E. JR. Johnson

AT the Cleveland meeting of the Institute in October, 1912, I had the honor to present a paper outlining the conditions surrounding the charcoal iron industry, and giving some of the results of an investigation started about three years ago for the purpose of determining the reason for the poor reputation of the Lake Superior charcoal irons as compared with the Southern and Eastern irons. In that paper I explained the effect of high carbon on quality, and tried to make clear that that paper was a preliminary one, as we felt convinced that we should eventually discover other factors affecting quality. The progress of the investigation has brought out facts that seem to us of the utmost importance practically and theoretically, and the purpose of the present paper is to present these facts with the proofs which seem to us to establish them. The closing year of the nineteenth century saw the publication of the first definite and connected statement of the relationship between the cast irons and the steels.' The metallurgical world was ready to accept the fundamental unity of these two series, acceptance being greatly hastened by Professor Howe's classic paper, The Constitution of Cast Iron, presented at the Richmond meeting of the Institute, February, 1901.

Jan 1, 1914

By H. J. Struth

A glance into the immediate future of the refining industry, and a retrospective view of 1929, cannot fail to emphasize the need for effective measures of control of refinery still runs. With oil producers alert to the need for control of the crude supply, it has become more than ever necessary for refiners to complete the movement toward stabilization by concerted determination to maintain still run schedules within the limitations prescribed by the demand for gasoline. The outlook for continued growth in the demand for gasoline appears to be well sustained by a preliminary survey of requirements for 1930. In fact, it is apparent that the industry will be assured of a market for gasoline that will aggregate in volume at least 472,000,000 bbl. this year. This indicates a gain in total demand over 1929 of about 9 per cent. or about 4.6 per cent, less than the gain recorded during 1929 over 1928, which amounted to 13.6 per cent. Despite the indicated increase in gasoline demand this year, it is apparent that little, if any, more crude will be required than last year. This is shown in Table 1, presenting estimates of gasoline demand and probable crude requirements for 1930. Table 1.—Preliminary Survey of 1930 Gasoline and Crude Run Requirements Millions of Barrels Doniestic gasoline demand................................... 397 Foreign gasoline demand..................................... 75 Total indicated demand...................................... 472 Natural gasoline content..................................... 53 Net gasoline from crude...................................... 419 Imported gasoline........................................... 13 Net gasoline required from refineries.......................... 406 Indicated excess stock Dec. 31, 1929........................... 10 Maximum protluction required................................ 396" At 40 per cent. gasolitlc recovery, this represents a maximum crude converson of 990,000,000 bbl., or a daily average for the ycar 2,712,000 barrels. Year after year, the refining branch of the petroleum industry has been found guilty of running crude to stills greatly in excess of normal requirements, causing frequent periods of market depression. A review

Jan 1, 1930

By O. H. Eschholz

The electrostatic process of fume precipitation is an excellent example of the successful application of scientific knowledge to an industrial operation. Originally proposed for the precipitation of sulfuric acid mists, it has been extended until at present there is practically no fume-carrying gas to which the method cannot be applied. Among the more common applications are: the recovery of non-ferrous smelter flue-dust, iron blast-furnace dust, cement dust, and potash fume. It should be borne in mind that the process is restricted to the precipitation of suspended particles, either liquid or solid, and does not separate gaseous constituents. However, by proper temperature control, mixtures of vapors having different temperatures of condensation to either solids or liquids may be selectively precipitated. The process consists essentially of subjecting suspended particles, including those too minute to be effectively acted upon by centrifugal or gravitational forces, to such an electrical force that they are driven from the gas stream, acting as a conveyer, and deposited upon a suitable receiving surface. This directional impulse is obtained from the interaction of charged particles and an electrostatic field of definite intensity gradient existing between two dissimilar electrodes, known as discharge and receiving electrodes. In principle, the equipment is equally simple. As shown diagrammatically in Fig. 1, it consists of: (1) A source of high-potential direct, current,, requiring: (a) Source of alternating-current energy. (b) Means of transforming from low voltage to high voltage. (c) Means of converting alternating to direct current. (2) Precipitation chamber having: (a) Transmission tubes for fume-laden gases. (b) Suitably designed and disposed electrodes. (c) Means for affecting removal of deposited solids. Although Hohlfeld demonstrated, in 1824, that a smoke-laden atmosphere could be cleared by applying an electrostatic field, and while Sir

Jan 1, 1919

By L. E. Tanner

A study was made of the transformation kinetics of the commercial titanium-base alloys, Ti-2.5Al-16V and Ti-4A1-3Mo-1V, using two different heat treatment cycles: 1) step-quenching to aging temperatures from a ß solution anneal and 2) water-quenching from an a+ß solution anneal followed by reheating to aging temperatures. Metallographic examination and hardness testing provided the major portion of the data, while electrical resistivity, dynamic elastic modulus, and X-ray diffraction techniques were also used to obtain critical or confirnzatory data. TTT diagrams were constructed from these results. The sheet alloys, Ti-2.5Al-16V and Ti-4Al-3Mo-lV, are of current interest to the Department of Defense. As an aid to the planning of their respective heat treatments, a program was carried out to determine the transformation kinetics of these alloys using ß and a + ß reference states. This paper presents the TTT diagrams constructed from data obtained by metallographic examination and hardness testing, as well as by X-ray diffraction, electrical resistivity, and dynamic elastic modulus determinations. EXPERIMENTAL PROCEDURE Materials—Sheets of the alloys were obtained from the producers in the "mill anneal'' condition and were tested prior to shipment to assure their meeting mill specifications. Chemical analyses were also supplied and are presented in Table I. Heat Treatment—The majority of the data presented in this study were obtained from hardness testing and metallographic examination. Sample coupons were cut from the alloy sheets and heat treated on a mass scale. The annealing cycles were operated in the following manner: 1) The ß solution anneals were carried out in a horizontal tube furnace with the bare samples protected by a dynamic helium atmosphere. Following this treatment, the samples were quickly transferred to lead, solder, or oil-bath furnaces for aging. After prescribed times at the various reaction temperatures they were water-quenched. 2) The second cycle simulated commercial practice, which requires the alloys be quenched to room temperature following the a + ß sotution anneal. This anneal was carried out in a muffle furnace with a dynamic helium atmosphere. The specimens were then reheated from room temperature to the reaction temperatures in lead, solder, or oil-bath furnaces, followed by water-quenching after prescribed times at these temperatures. Information concerning the critical temperatures of the alloys was obtained from the literature and solution treatments were based on these values. A summary of the solution annealing treatments is found in Tables II and 111. The aging temperatures for the (a - ß alloys ranged in 50°C intervals from 200°C (392oF) to approximately 50°C below the ß/a + ß transus in the first cycle and approximately 50°C below the a + ß solution temperature in the second. The transformations in these alloys were known to be rather rapid, and thus aging times started at 0.5 min and went to a maximum of 7000 min. Hardness Testing and Metallographic Preparation— Heat-treated samples were sheared and mounted in Bakelite with their cut edges exposed. After a flat surface was ground, the hardness was determined in Vpn on an Armstrong-Vickers machine utilizing a 20-kg load. Three to four impressions were made on each specimen. After this procedure, the hardness impressions were removed and the edge surfaces of the specimens were prepared for metallographic examination in the usual manner. The etchant was 20 pct HF and 20 pct HNO3 in glycerine. Electrical Resistivity—It has been shown that the isothermal reactions in titanium-base alloys can be followed by measuring the changes in e1etrical resistivity attending these transformations. As mentioned earlier, the reaction kinetics of a-ß alloys are rather rapid; thus, it would be expected that resistivity data obtained from these alloys would be more significant if measurements were made continuously at the respective aging temperatures. To accomplish this end a special apparatus, based on the current-potential principle, was assembled. Its design was derived from earlier devices constructed by Colner and zmeska1 4 and Levinson.5 The set-up provided for the heat treatment zof machined specimens (approximately 2 x l0-4in. in cross section by 3 in. in length) and the determination of their relative

Jan 1, 1962

By A. T. Shurick

THE present economic crisis in bituminous coal is substantially the most insidious, and critical, in the modern history of the industry. The large consumption deficit that has gradually developed (almost unawares), has culminated in a situation that has forced home the urgent necessity for prompt and radical remedial measures, such as the various mergers now in course of negotiation. Conditions today are sufficiently comparable with those in the iron and steel industry, preceding the formation of the United States Steel Corpn., to suggest the possibility of a sweeping super-consolidation, that all but staggers the imagination. The important function of the banker in this, and lesser projects, is too well known to require comment, and it is important that we understand clearly just what these functions are. Certain features in banking practice came up for consideration in connection with a rather exhaustive economic study into the prospective future of the coal industry, upon which I was recently engaged for an Eastern bituminous interest. This survey was made for the purpose of effecting a decision on certain pressing questions of policy, involving considerable capital expenditures, that would be compatible with the flattening out in the curve of production in recent years. An examination of the TRANSACTIONS, and the coal literature generally, failed to disclose any pertinent, and authoritative data, on this subject. This was more or less characteristic of the whole survey, which had involved a large amount of original research, and measures were taken to procure the required information. The following notes have been compiled largely from the data thus collected, supplemented with material, suggestions and criticisms, by several of the larger banking houses active in coal, together with personal memoranda of my own.

Jan 1, 1928

By C. Zener, J. H. Hollomon

IT Is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect o rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. EARLIER INVESTIGATIONS A clear analysis of the conditions necessary for plastic flow and for fracture was first given by Ludwik,1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis, both a flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracture is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence or now stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The. curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated' by the authors. According to this principle of equivalence, strain rate E and temperature T affect the flow stress only through a single parameter p of the form: p = EeQ/RT [I] In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. Combinations of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By R. H. Oliver

The purposes, types, preparation, and testing of flocculants are discussed. A flocculation compendium is included, indicating choice of flocculant for a given set of conditions. An economic evaluation of the process is presented. Solid-liquid separation is a major expense in most mineral processing flowsheets today. Proper use of flocculation can often lower the overall cost of a solid-liquid separation by reducing the size of sedimentation or filtration equipment. PURPOSE OF FLOCCULATION When is use of a flocculant justified in terms of overall process economy? 1) when it results in process improvement, such as producing a clear liquor for electrolysis, precipitation, ion exchange, or solvent extraction; 2) when it results in satisfying requirements of pollution abatement ordinances; 3) when it results in increased recovery of values that would otherwise be lost; or 4) when it results in considerable savings in capital expenditure due to use of smaller equipment. When can the use of a flocculant adversely effect overall process economy? 1) when it results in increased filter cake moisture, 2) when it results in decreased filtration rates, 3) when it results in considerable bulking of sedimentation underflow, 4) when it contaminates either the supernatant or sludge, or 5) when the cost of using the flocculant is greater than the savings due to its use. First step in consideration of flocculants for a given application is establishment of desired goals in terms of increased clarity of effluent, increased recovery of solids, or decreased size of equipment. The most economical solution to a solid-liquid separation problem is that combination of equipment and flocculant costs which meets the established goals at the lowest total annual expenditure. This economic decision can be made only after technical data has been obtained as outlined in next four sections. TYPES OF FLOCCULATION Flocculation is a process wherein individual particles are united into more or less tightly bound agglomerates or flocs, thereby increasing effective particle size of solids suspended in a liquid. Degree of flocculation of a suspension of finely divided solids in a liquid is controlled by a combination of probability of collision between particles and probability of adhesion after the collision has occurred.' Probability of collision can be increased commercially through use of a paddle-type flocculator, combination flocculator, and clarifier or flocculating-type feedwell. Probability of adhesion usually can be increased by addition of a reagent known as a flocculant. Reagents act as flocculants through one or a combination of three possible mechanisms. The first is electrolytic neutralization of inter molecular repulsive force due to Zeta potential. This neutralization enables Van der Waal's cohesive force to hold the particles together after they collide.' The second is the precipitation, within a definite pH range, of voluminous metallic hydroxide flocs which entrap fine particles. This process is known as coagulation.14 Third is the bridging of two or more particles by either natural or synthetic long-chain, high-molecular-weight organic polymers. This bridging is accomplished by adsorption of two particles at different sites on the same molecule or by bonding of two molecules, each adsorbed to a different particle. Considerable effort has been expended in explaining the action of these polyelec-trolytes and detailed accounts are available in the literature. CHOICE OF FLOCCULANTS It is impossible, at the present time, to specify the optimum type or amount of flocculant for a given application from a knowledge of the material to be treated. The standard procedure is to choose reagents or combination of reagents most likely to be effective on the slurry; then test them.' The accompanying Flocculation Compendium (Table I) contains details of all currently available reagents sold as flocculants and it should be used when selecting the group of reagents for tests. This selection can be based on information listed in columns 4 and 5. Column 4 presents industries in which each floc-

Jan 1, 1961

By Robert J. Hite, Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table 1), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term potash originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first US patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 27.5 Mt K20 produced in the world in 1980 (Searls, 1981) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K20, a unit of measure which is neither a natural nor synthetic compound of potassium (1.0% K is equivalent to 1.2046% K2O). Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and metamorphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such deposits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of seawater or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in Table 1. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971). The structural basins within which marine evaporites occur are of two main types: (a) cratonic basins formed by broad epirogenic movements (for example, the Michigan Basin of the midwestern United States and the Permian Zechstein Basin of eastern Europe), and (b) grabens, commonly related to continental

Jan 1, 1983

By Arthur Winslow

Introductory.—The following paper is based upon a report on the lead- and zinc- deposits of Missouri, prepared for the State Geological Survey, which is now being printed. This report is the outcome of work prosecuted by the writer, assisted by Mr. J. D. Robertson, during the past five years. The studies in the State were supplemented by examinations of the similar ore deposits in Wisconsin and Arkan- sas. The report will contain in all about 800 pages, and the aim has been to make it complete and exhaustive, especially in descriptive matter. Naturally, only a brief outline can be presented here, and the reader is referred to the report itself for further details. Contents. I.—History and Statistics, . . 636 II.—Topography of the Region, . 639 III.—General Geology, . . .639 The Archean, . . .639 The Algonkian, . . 640 The Silurian, . . .640 The Devonian, . . 640 The Lower Carboniferous, 641 Tie Coal Measures, . 641 The Tertiary, . . .641 Structural Geology,. . 642 IV.—The Ore-Deposits, . . .643 Geologic Distribution, . 643 The Forms of the Ore-Bodies, . . .641 The Composition if the Ore-Bodies, . . .645 Gangues, . . . 645 Minerals, . . .618 Paragenesis of Minerals, . . . 651 The Structure of the Ore-Bodies, .... 651 V.—Descriptions of Types, . . 652 The Eagle Mines, . . 652 Shaft No. 23, . . 652 The Western Zinc Company or Oswego Lands, 651 The Gobar and Tomlinson Shaft, . 655 The Alba Company's Mine, 656 The Victor Mine, . . 658 The Bonne Terre Mines, . 660 General Geology, . 660 The Ore-Bodies, . 661 The Vallé Mines, . . 664 The Garatee Mines, . 664 The Corn-Stalk Diggings, . . .665 The Virginia Mine, . 666 The Conlogue Mine, . 667 VI.—The Mode of Formation of the Ore-Bodies, . . 670 The Formation of the Cavities. . . . 670 The Filling of the Cavities, . . . .675 The Formation of the Breccia Deposits, . . 673 The Formation of Circle Deposits, . . .674 The Impregnated Deposits of the Southeast, . 676 VII.—The Origin of the Metalliferous and Other Minerals, 676 1. Originally Deposited in Concentrated Condition, 676 2. Derived from Great Depths, . . .677 3. Original Diffusion, Supplemented by Lateral Secretion, . . . 678 4. Concentrated Through Surface Decomposition, 681

Jan 1, 1895

By H. H. Keller, E. J. Couch

Damage to production wells subjected to the high temperatures associated with in-situ combustion projects has been a problem since the advent of this thermal recovery technique. Injection of water down the annulus of hot wells has been successfully utilized for cooling and prolonging the life of such wells. A mathematical model that is suitable for predicting the effectiveness of cooling water in a particular application is developed. Typical results for practical ranges of the various parameters involved are presented. INTRODUCTION In the normal course of in-situ combustion operations, highly damaging conditions develop in the production wells as the combustion zone approaches, and these wells are subjected to high temperatures (up to 1500F). The resulting well damage is recognized as one of the more serious operating problems unique to the in-situ combustion process. Even in operations where well completions have been specifically designed to cope with this problem, the question arises as to how this destructively high temperature can be kept within tolerable limits. A simple and economical approach to this problem is to circulate cooling water down-hole. This method has been used with some success in shallow reservoirs. At greater depths, however, the heat exchange with the overburden surrounding the well and between the fluids in the tubing and the annulus tends to equalize the temperatures of the two fluid streams so that the cooling capacity delivered to the bottom of the hole decreases with well depth. This method would provide no appreciable control over the bottom-hole temperature at great depths. In order to delimit the condition under which cooling by water circulation is effective, the wellbore temperature must be related to the water inlet rate and temperature; to the reservoir depth, production rate, and initial temperature; and to the combustion at at bot tom-hole depth. A model that meets these requirements and that will offer an approach for developing engineering solutions to practical design and operating problems is described in this paper. MATHEMATICAL MODEL Previous studies of temperature distributions include those for flowing wells1p2 and those for hot fluid injection. Adams and Haddenhorst 6 presented solutions for the down-hole circulation of hot oil in the treatment of paraffin-deposition problems. In this paper the thermal model presented by Ramey 4 is adapted to the flow system shown schematically in Fig. 1. Water at temperature Ti is injected at a rate wi and flows down the annulus outside the tubing. It mixes at bottom-hole depth D with the fluids produced at race w from the hot reservoir at temperature T. This mlxtureJ. of injected water and reservoir fluids flows up the tubing and is produced at the surface at TI,. In order to describe the temperature response in this system, we make use of the usual conservation of

Jan 1, 1969

By R. M. Brick, Arthur Phillips

The normal method of preparing metallic alloys for commercial use involves the preparation of a melt containing the given components in the chosen proportions and allowing the homogeneous liquid mass to solidify in a mold of the desired form. The solidification is frequently accompanied by a segregation of the alloying elements in different parts of the casting. When the segregation is occasioned primarily by marked differences in density of the solid and liquid phases, it is termed "gravity" segregation. When the segregation conforms to a selective freezing in harmony with the teachings of the equilibrium diagram of the alloy system—i.e., the lower melting phases are concentrated in the regions of the casting last to freeze—it is often referred to as "normal" segregation. However, in many cases the lower-melting part of the system is concentrated in the parts of the casting first to freeze and the result in this case is termed "inverse" segregation. To complete the terminology of the subject, normal segregation in a single phase is usually called "coring" and the word will be used in that sense in this paper. Inverse segregation, particularly when the liquid phase is exuded or sweated out on the surface of the casting, is sometimes called "liquation." Unfortunately, some ambiguity has arisen from the use of this term and it is perhaps advisable to confine its use to the dictionary definition; namely, "The separation of two phases by heat sufficient to melt one but not the other." The gravity and normal types of segregation are both well understood and to some extent, are controllable by taking advantage of the most favorable cooling rate for a given casting condition. Inverse segregation has received considerable attention from several investigators but none of the theories offered seem to account in a convincing way for the many examples of this type. The observations made in the present work on segregation in single crystals, and in some other castings, tend to support one theory of the mechanism of inverse segregation and definitely to

Jan 1, 1937

By H. G. Doll

The S.P. log is shown to be a measurement of the potential drop along the drill hole, caused by ohmic effect in the mud. The notion of static S.P. is brought forward, and its relation to the S.P. log is discussed. Other factors influencing the shape and amplitude of the log are considered; attention is given to conditions encountered in practice. Numerous figures are given illustrating graphically the results; these figures are of particular interest for comparison with field examples. The S.P. log, although indicating permeability, is not an absolute measurement of permeability, nor of porosity, of the formations traversed by a drill hole. It is affected by several parameters, such as resistivity of formations and mud, thickness of formations, and others, which should be appraised carefully. Simple rules have been established for a better distinction of the boundaries of permeabl: sections, particularly in difficult cases, such as those encountered in highly resistive formations. A systematic application of the established principles will assist in obtaining more information from the S.P. log than was possible thus far; for instance, under favorable conditions, presence of oil may be detected, or amount of shale in sands may be estimated. Introduction The S.P. log, or spontaneous potential log, has been known and widely used during the last 15 years for the location of permeable beds traversed by drill holes.1,2 In electrical logging practice, the S.P. log is shown on the left hand side track of the record (as may be seen in later examples) where it can be easily correlated and interpreted with the resistivity curves located to the right. Usually, the S.P. log consists of a base line, more or less straight, having excursions or "peaks" to the left. The base line frequently has been found to correspond to impervious beds, while the peaks are usually found opposite permeable strata. Measurements which will indicate positively the presence of permeability in the formations, and which will give accurately the boundaries of the permeable zones, are of great importance in oil-field practice. Thus far, the S.P. log is the best approach to such determinations; unfortunately, its interpretation is not always evident. With respect to the base line of the S.P. log, it may be noticed that this line is not always at a definite location on the chart. Sometimes it may shift abruptly, while other times a gradual drift is apparent. As far as the peaks are concerned, their shape is not uniform; some are rounded while others are sharp. Also, from other data, it may be found that occasionally the peaks extend appreciably beyond the boundaries of permeable zones into zones which are not everywhere permeable. A comparison with permeability measurements made on cores has often confirmed that there was no definite correspondence between the magnitudes of the peaks and the permeability values. In the same geological horizon, it generally will be found that most of the thick and permeable for-

Jan 1, 1949