Search Documents

By V.K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By V. K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By K. C. Hong, R. B. Jensen

The problem of determining the optimum set of steam volumes and cycle lengths for a single well undergoing multicycle steam stimulation in order to maximize the cumulative discounted net income has been formulated mathematically and programmed for a digital computer. The mathematical fonnulation of the problem and the method for its solution are discussed in this paper. The oil production performance during each stimulation cycle was simulated by either a constant percentage or a harmonic decline. Using simple analytical expressions for production performance, the cumulative discounted net income and cumulative time of operation were related to the pertinent process and cost parameters and two principal process control variables (cycle length and steam injection volume). The discrete maximum principles was used to transform the equations for cumulative time of operation and cumulative discounted net income into a set of simultaneous equations. The simultaneous equations then were solved by trial and error on a digital computer to determine the set of cycle lengths and stem injection volumes that gives maximum cumulative discounted net income over the project life. INTRODUCTION Steam stimulation is a process for improving the oil recovery rate from wells producing high-viscosity crudes. The process is applied on an individual well basis and is executed in a series of cycles, each consisting of three phases: steam injection, soaking (steam condensation), and production. Significant increases in production rate following the stimulation operation result from heating the reservoir around the wellbore. As heat is removed with produced fluids and dissipated into nonproductive formations, the production rate declines, usually to near the prestimulation value. Typical production responses are given in case histories reported by Owens and Suter,l and are depicted in Fig. 1. Duration of the production phase is equal to the time for the oil production rate to decline to some specified value and is called the cycle length. (Cycle length is defined as the producing portion of the cycle and does not include the downtime required for steam injection and soaking operations.) Termination of the production phase coincides with the start of steaming for the next cycle. The process is continued, cycle by cycle, until it becomes unprofitable. Models 2-4 have been developed to simulate behavior of a single well during one cycle of steam stimulation and have been used to investigate the effects of system and operating conditions on the production responses. However, these investigations have not shown how the models can be used to determine a most profitable set of operating conditions for a multicycle stimulation project. Perhaps these models are too complicated mathematically to be adapted readily to an optimization study. This paper presents a method for optimizing a multicycle steam stimulation project based on simple production performance models. First, the performance of a steam-stimulated well during each cycle was simulated by either a constant percentage or a harmonic decline model. Using these simple analytical expressions for production performance, the cumulative discounted net income (before tax) and cumulative time of operation for each cycle were related to the pertinent process and cost parameters and two process control variables—the cycle length and the steam injection volume. Finally, the profit function to be maximized was formed. The analogy between the above problem and problems of optimizing multistage decision processes that have been reported extensively in the chemical engineering literatures5-10 in recent years has led this investigation to the use of the discrete maximum principle.5-7 This principle was used to transform the equations for cumulative discounted net income and cumulative time of operation into a set of simultaneous equations characterizing the optimum operating conditions in terms of the two control variables. These equations

Jan 1, 1970

By Michael Tenenbaum

THE importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1947

By Clarence G. Merritt

Stainless iron, as mild stainless steel is usually called, an alloy ranging from 11.50 to 15.00 per cent chromium with carbon under 0.12 per cent, has been considered to be not appreciably affected in respect to corrosion resistance by heat treatment. This metal, while one of the most widely used of the "straight" chromium stainless alloys, has failed in many applications because of insufficient information regarding heat treatment. These failures have been attributed to many possible causes from an inherent lack of resistance to corrosion and misapplication to mlysterious electrolytic effects or comparatively minute non metallic inclusions. Many uses for a steel with such excellent physical properties as are latent in this alloy have been lost on account of corrosion failures which could have been avoided by applying proper heat treatment. The alloy has not received the recognition or attention it should because of the fact that the details of its metallurgical behavior were not thoroughly understood. Response to heat treatment of the steel is well known as regards tensile properties,1-2 but its application has been for improvement in tensile characteristics or on account of machining considerations rather than for corrosion prevention. The potential user of this steel has not been clearly advised in papers, either technical or commercial, that have been written about it in the last 10 years or more, of particular features that are of prime importance in developing the excellent properties of this metal. The data to be presented in this paper are concerned mainly with the effect of heat treatment on the corrosion resistance, but a study has also been made of the concurrent microstructural changes and an explanation developed for the phenomena revealed, as well as a correlation to the other physical properties—hardness, tensile characteristics and impact strength. Stainless steel, largely used for cutlery purposes, an alloy of approximately 13.00 per cent Cr with 0.30 per cent C;, must be hardened and the surface prepared by polishing or pickling for best resistance to staining and corrosion. Monypenny reports that a loss of hardness is

Jan 1, 1932

By John Drew Ridge

For the early conservationists before the first decade of the twentieth century, conservation meant largely the planned preservation of water, forest, soil, and wildlife resources-renewable natural resources-through efficient use. Water was primarily thought of as a resource that must be kept available for humans to enjoy in a recreational sense and as a habitat for wild animals, birds, and fish. Little thought was given to conserving water for actual human or industrial needs. If industry entered the picture it was as an actual or potential polluter of water, which was the basic necessity for drinking and bathing and for outdoor recreation. Even the forests were only held worthy of conservation largely because they were areas in which wildlife could, or should, abound and in which human beings might find relief from the cares and problems of everyday life. Finally, the soil was to be preserved in its natural fertility through proper fertilization, cultivation, and crop rotation; in this the conservation program did enter the realm of the practical. For through soil conservation, the world was to be able to raise increasingly large crops of constantly improved organic foods which the steadily growing population of the earth was to need to survive and improve. Relatively little time, however, was spent on considering what profit the farmers of the world were to make from the scientific farming on which they were to embark. In short, the appeal of the early conservationist program was much the same as that of the entire era of Theodore Roosevelt of which it was a part; it was to the heart rather than to the mind; it was to emotion rather than to reason. Because of the way in which the problem was approached, conservation took on the character of a crusade rather than that of a practical plan for the betterment of man through economically sound methods of improving his environment and the uses he makes of it. Conservation had, then, all the advantages of a stirring appeal to the emotions, but it did not have the lasting results that would have been achieved by a program with a sound economic basis.

Jan 1, 1959

By Raymond B. Ladoo

ABRASIVES include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical action polishes and cleaners may also contain solid abrasives; for example, many metal polishes. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains

Jan 1, 1949

By Frederic L. Kadey

Diatomite is a siliceous, sedimentary rock consisting principally of the fossilized skeletal remains of the diatom, a unicellular aquatic plant related to the algae. Thus, it has-been formed by the induration of diatomaceous ooze, and consists mainly of diatomaceous silica, a form or variety of opal which is first formed in the cell walls of the living diatom. Diatomaceous silica is not generally regarded as a synonym or the equivalent for diatomite, although it has been so used at various times. Accurately, diatomaceous silica is the preferred name for the principal mineral component of which the rock, diatomite, is composed. The terms diatomaceous earth and kieselguhr are used as synonymous with diatomite. The designations tripoli, tripolite, infusorial earth, etc., were used at one time but are now obsolete. With the changing nomenclature, these terms that were at one time correct when proposed and used for generations would be considered incorrect if used today in the light of current knowledge. The designation diatomite is reserved for those accumulations of diatomaceous silica that are of sufficient quality, size, and minability to be considered of potential commercial value. Processed diatomite possesses an unusual particulate structure and chemical stability that lends itself to applications not filled by any other form of silica. Foremost among these applications is its use as a filter aid, which accounts for over half of its current consumption. Its unique diatom structure, low bulk density, high absorptive capacity, high surface area, and relatively low abrasion are attributes responsible for its utility as a functional filler and as an extender in paint, paper, rubber, and in plastics; and as an anti-caking agent; thermal insulating material; catalyst carrier; and chromatographic support; polish, abrasive, and pesticide extender to name a few representative applications. The United States is the principal producing country, although diatomite is found in numerous other locations.

Jan 1, 1975

By Charles R. Wraith

The property of the Roan Antelope Copper Mines, Ltd., is situated at Luanshya, north central part of Northern Rhodesia, and is connected with the main line of the Rhodesia Railways, Ltd., by a 24-mile branch line from N'dola. Most of the material and supplies that are not available in Africa are shipped into the country via Beira, on the East Coast of Africa, a distance of 1473 miles from Luanshya and the nearest ocean port. The output of copper is shipped by rail to Beira and thence by boat to the market. Passenger travel is mostly via Cape Town, a distance of 2162 miles from Luanshya. Excellent passenger trains operate on regular schedules between Cape Town and Northern Rhodesia. Luanshya is 13" south of the equator at an elevation of 4000 ft. above sea level, and has a mild healthful climate. During the rainy season, from October to March, the rainfall averages 53 in. The area is profusely covered with vegetation. An ample supply of water for industrial and domestic purposes is available throughout the year. The more important supplies for smelting purposcs, such as wood, coal, limestone, silica, quartzite, and clay for "dolly" mud, are conveniently available. Excellent grades of coal, coke and firebrick are obtained from the Wankie Colliery Co., Ltd., Southern Rhodesia. The Wankie colliery has just completed the erection of equipment for the manufacture of silica brick. An ample supply of quartzite of good grade is available for this purpose. Silica brick is also obtained from the Belgian Congo and from India. Limestone is quarried from a large deposit a few miles from Bwana Mkubwa, which is 30 miles by rail from the smelter. An abundant supply of clay for " dolly " mud and for lining launders is available within a short distance of the smelter. Metallurgy Copper is contained in the ore as chalcocite, chalcopyrite and bornite. Chalcocite predominates in the eastern end of the orebody almost to the exclusion of other copper minerals. The amount of chalcocite decreases with a corresponding increase of chalcopyrite and bornite toward the western extension, where the latter predominate.

Jan 1, 1934

By J. T. Eash, E. M. Wise

In a previous communication1 the improvement in slrength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are presented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for determining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum. 4. The variation in the solubility of this platinum-content phase in the alpha solid solution with the temperature has been determined. This

Jan 1, 1933

By John Alden

A CONSIDERABLE PROPORTION of the tonnage of aluminum used today has at some stage during its manufacture, been rolled. I. For one, therefore, was particularly pleased to hear that this Society was to hold a symposium on rolling of nonferrous metals. Metallurgists can well afford to direct their close attention to the metallurgy involved in this important operation. To one who has seen today's high production rolling mills for aluminum it is difficult to realize that the first aluminum rolling mill For sheet was installed a scant 55 yr ago, in 1892. This mill was a three-stand train of 2-high mills, driven by a steam engine and was operated for many years successfully rolling aluminum sheet. Mills for the rolling of aluminum rod were installed in 1899 to meet the demand For manufacture of electrical conductor wires and cables. Bars and rods in straight lengths were also made. While these mills were the first built for rolling aluminum products of these types some rod had previously been rolled on brass and copper mills. Not until many years later, in 1929, however, Were facilities provided for the rolling of structural shapes, such as I-beams and channels. Growth of the aluminum sheet business and the necessity for economical manufacture soon brought the realization of the economies resulting From-the rolling of sheet in long lengths and coiling it. A five-stand continuous mill driven by a steam engine, was in operation late in 1907. This took aluminum slabs coating from

Jan 1, 1948

Gentlemen of the American Institute of Mining Engineers.—As you well know an application is about to be made to Congress, by the American Society of Civil Engineers, for the appointment of a cornmission composed of persons skilled in the production and use of iron, steel, and other structural materials, whose duty it shall be to test the strength, elasticity, and other quatities of such materials ; not simply the substances used as such, but the members of large structures composed of such materials, of the forms and sizes in which they are actually used. As I understand, the papers that will be read here to-night will have for their object to show the necessity for such tests, and therefore the necessity for the commission asked for. As the representative of the Society of Civil Engineers, I have to thank you, gentlemen of the Mining Engineers, for the great zeal with which yon have taken up this subject, and seconded the efforts of the Civil Engineers; or, perhaps I ought rather to say, initiated the efforts to get a suitable commission appointed to obtain most vitally important information which it is admitted on all hands we do not now possess. In drawing up the memorial to Congress, in connection with some of the ablest and best informed of our Society, and in all the discossions on the subject, I have been struck with the emphasis with which the confession is made, that so little is known of the strength of the larger-sized members constantly used in building structures of the magnitude which the present requirements of the country now demand. I presume the remarks made to-night will bring this out very prominently. This is no disgrace, for with the means here-

Jan 1, 1882

By Richard H. Jahns

Terminology and Basic Specifications Minerals and closely allied natural substances that are used for personal adornment, as raw stock for the fashioning of ornamental objects, or for other decorative purposes can be referred to collectively as gem materials. Industrial gem materials are those employed directly in various areas of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconstant, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Although many building and monumental stones are undeniably ornamental in their uses, treatment of such material is beyond the scope of this chapter. Substances that lose their identity in use are excluded from the gem category. Thus a transparent crystal of beryl would not be classed as a gem stone if it were treated as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means of distinguishing different gem materials on the basis of their recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquois, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of intrinsic properties, and at the present time all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance desirable characteristics that are present initially. The worth of most synthetic gem stones is founded upon the identity between their major properties and the natural characteristics of the corresponding minerals, just as the pleasing qualities of imitation stones depend upon how well certain of their properties simulate those of more valuable substances. The most important specifications of gem materials represent four basic factors: beauty, durability, rarity, and portability. Beauty, whether expressed as splendor, "purity," attractiveness, or in some other way, is mainly a function of personal response to optical properties such as color, transparency, indices of refraction, and dispersion. Freedom from visible imperfections is important for transparent stones. For some substances beauty depends also upon asterism, opalescence, textural and

Jan 1, 1960

By Alden Greninger

THAT metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc alloys.1 In all three of these alloy systems the martensite structures result from transformation of the metastable ß phase when the speed of cooling from the ß range is sufficiently high to suppress decomposition into equilibrium phases. ? In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require readjustments of concentration. For example, the marten-site transformation in 60:40 (ß) copper-zinc does not begin until the temperature has dropped to about minus 30° C., and then continues down to minus 130° C. and probably even at lower temperatures.1 Further-more, martensite processes apparently proceed only while the tempera-ture is falling, within the proper range, and cease completely while the temperature is held constant; ? and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of martensite processes by postulating that the mechanism " . . . consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Hewitt Wilson

IN 1903, T. M. and E. H. Alvord, of Marblemount, Wash., built a soapstone-grinding mill in the Skagit River Valley and are reported to have produced "ground talc" during 1904 and 1905, shipping to the paper mills in Wisconsin. Between 1916 and 1920, the Western Talc Co. built and operated a talc-grinding mill north of Mondovi, on the banks of the Spokane River, in eastern Washington, and sold powdered talc to the Inland Empire Paper Co. of Spokane. ? The most active develop-ment in recent years has been by two companies in the Skagit Valley-the Skagit Talc Company, Inc., which has been sawing soapstone block for the soda-recovery furnaces of the pulp and paper companies, and the Asbestos-Talc Products of Washington, Inc., at Burlington, which has been mining and dry-grinding a soft serpentine for the structural filler and insulation trade. Many prospects have been opened in the northern part of the state on both sides of the Cascade Mountains, and these activities undoubtedly are the forerunner of an industry that promises to attain considerable magnitude in the North Pacific States. At the present time, talc is imported from California for use as paper filler, and soapstone block from Virginia for use in the soda-recovery furnaces. A small market has been created locally for tailor and foundry:, pencils, stove grills, and block soapstone for art objects. The results of the present study, as yet incomplete, indicate that the use as a refractory and as a ceramic filler and flux can be expanded.

Jan 1, 1936

By Carlo Massa

THE Societá Auonima di Miniere e di Alti Fourni, familiarly known as the " Elba Company," works the rich ore-deposits of the Island of Elba under a long-term contract with the Italian Government. The ore-deposits are scattered over the eastern and southeastern coast; but as those parts of the island are not well provided with ports, the blast-furnaces were built at Portoferraio, the principal town of the island, situated on the northern shore, and possessing a magnificent natural harbor where even vessels as large as the battleships of the Italian navy can comfortably anchor. In the selection of Portoferraio. the cost of transporting the iron-ore from the different mines to the blast-furnaces has been reduced to a minimum, and shelter has been provided for the Company's flotilla of tugs and barges, as well as for the steamers carrying coal and pig-iron. The whole plant, of which a general view is given in Fig. 1, comprises 1. A discharging-pier with unloading-cranes. The ore and coal are transported from this pier by means of an aerial cable-rail¬way to the coal- and ore-storage yards. This cable-railway is supported by an iron bridge extending from the pier to the shore and by a wooden trestle extending from the shore to the yards. , 2. Blast furnaces, two in number, with all the accessory appa¬ratus, such as blowing-engines, dry purifiers, Cowper hot-blast stoves, hoists, etc. 3. Coke-ovens, two batteries, with coal-bin, crushers and boilers. 4. Engine-house containing the blast-engines and the electric generating-station. 5. Pumping-plant. 6. Narrow-gauge railways.

Mar 1, 1905

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

THE production of titanium in 15-1b. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,1 has provided adequate material for a study of the : physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the properties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. [ ] CONSOLIDATION OF THE POWDER The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at so tons per

Jan 1, 1946

By M. G. Corson

Until recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast stlate, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes —cakes, bars, ingots and billets—for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This Icd to four investigations: by E. Seidl and E. Schieboldll by P. Siebe12 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a wide zone of columnar crystals between t'he thin layer of fine crystal5 near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the castling machine. More recently, cast shapes of copper were investigated by X. 1'. Allenh and by C. Blazey. Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast Wirebars used. As far as the present writer can tell, no investigation mas under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, or otherwise.

Jan 1, 1938

By M. G. Corson

Until recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast stlate, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes —cakes, bars, ingots and billets—for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This Icd to four investigations: by E. Seidl and E. Schieboldll by P. Siebe12 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a wide zone of columnar crystals between t'he thin layer of fine crystal5 near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the castling machine. More recently, cast shapes of copper were investigated by X. 1'. Allenh and by C. Blazey. Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast Wirebars used. As far as the present writer can tell, no investigation mas under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, or otherwise.

Jan 1, 1938