Search Documents

Jan 1, 1918

Lucien Eaton, Ishpeming, Mich. (communication to the Secretary *):—I began to use water Leyner drills at the Cliffs Shaft mine at Ishpeming, Mich., over four years ago, and now have over 20 in use. The ore in this mine is hard specular hematite, and is mined by the room-and-pillar system, the rooms being driven as breast stopes. For many years only 3 1/4-in. piston drills were used in the mine, each machine ordinarily being able to drill from 15 to 25 ft. of holes in a shift. In the hardest ground, however, it was often, impossible to drill more than 2 or 3 ft. in a shift. When water Leyner drills were used the footage drilled was materially increased, especially in the hardest ground, but it was found that in very hard ground the breakage of machine parts, and especially of drill steel, was very high. At this time round steel with lugs forged on the shanks was used, and most of the breakage occurred at or near the lugs. Many experiments were made in an endeavor to overcome this breakage, and it was finally decided to do away with the lugs altogether, and use hexagonal steel. Accordingly I designed a chuck to use hexagonal steel without luge, a tappet being interposed between the hammer and the shank of the' drill steel. The design of this chuck of the proper size for the No. 18 Ingersoll-Leyner drill is shown in Fig. I. The different parts are also shown photographed in Fig. 2. A is the barrel of the chuck, which revolves inside the front head. It is made of machinery steel. B is the bushing which screws into the front end of the barrel A, and in which the drill steel fits loosely. This is turned down from a steel casting, the hexagonal hole being cast and then broached out to the proper size. It is case hardened inside. C is the tappet, which fits smoothly inside A just behind the bushing B. It is made of " N " temper Crescent tool steel and is carefully tempered. D is the tappet ring, which prevents the tappet from being pushed back too far by the

Jan 1, 1914

[ ]

Jan 1, 1938

By W. P. Blake

Among the many interesting objects to be seen at the Vienna Exhibition last summer, the model of the system of underground transportation by a continually moving chain, adopted at the Hasard collieries, at Micheroux, near Liége, Belgium, was one of the most attractive, and full of valuable suggestion to mining engineers. These collieries are under the superintendence of the celebrated

By H. T. Clark

Within the last twenty years at least three sets of lattice constants for the room temperature (alpha, hexagonal close packed) phase of titanium have been reported in the literature. These values, summarized in Table 1, differ one from another by amounts far greater than can be explained on the basis of inaccuracies in parameter measurements. This paper presents new values determined for high purity titanium. It also details the effect of two elements, oxygen and nitrogen, on these parameters and shows that two of the previously reported values are probably in error because of the presence of one or both of these elements in the material used for examination. Preparation of Samples The titanium+ used for this study was prepared by the thermal decomposition of titanium tetraiodide7 on a hot titanium filament. This titanium rod was prepared for X ray examination by melting about 10 g in purified argon in an electric arc furnace on a cold hearth. This cast button was cold rolled to 0.040 in. thick sheet, cleaned, annealed in vacuum at 1000°C and cold rolled to 0.020 in. thickness. About 0.003 in. of surface material was then removed by hand grinding on papers to remove any contamination caused by the rolls and the sample was bent to the radius of the focusing camera. The sample was then vacuum annealed at 600°C, a temperature just high enough to cause recrystallization, producing a fine grained structure. Such a structure is essential in sheet specimens prepared for focusing cameras in order to have a sufficient quantity of grains to develop continuous diffraction lines. The use of sheet specimens rather than powder samples appears to be essential for the X ray examination of titanium. This is because of titanium's exceptionally high gettering power and its rapid absorption of adsorbed gases, water -vapor, and the like at annealing temperatures. While the effect of this contamination may be neglected for sheet specimens, its effect on 200-300 mesh powder is appreciable. Titanium alloys of oxygen and nitrogen were prepared by a technique simi- lar to that described above except that the required amount of the highest purity titanium oxide or nitride available was added prior to melting in the arc furnace. These materials were added by placing them in holes drilled in the titanium. A small weight loss invariably occurs during the melting of these oxygen and nitrogen alloys. This is believed to be due entirely to the loss of some of the powdered compound in the blast of the electric arc, an assumption which is justified on the basis that there is no weight loss during the melting of titanium metal and that wet analyses for nitrogen on representative samples have checked with the calculated analyses when it was assumed that the entire loss during melting was due to the loss of titanium nitride powder. These alloy buttons were reduced to sheet in the same manner as used for the unalloyed titanium. Experimental Procedure A North American Phillips 12 cm diam symmetrical precision focusing vacuum camera and copper radiation

Jan 1, 1950

By William Lodding

In leaching ores at atmospheric pressure it is often desirable to apply high reagent concentration, long exposure time, and elevated temperature. All of these conditions tend to increase the treatment cost. In conventional leaching, direct or countercurrent, the leaching fluid is needed to transport the solids through the process. This requires relatively large volumes of fluid and limits the reagent concentration economically feasible. The relatively high dilution also increases fuel cost if leaching is to be done above ambient temperature. Heating of water is expensive.

Jan 3, 1967

By William B. Plank

AN outstanding development in the field of education for the mineral industries during the past year has been an unprecedented eagerness by young men for college training in this field. The enrollment of students in the 53 mineral technology schools in the United States in 1936-'37 reached the all- time high of 7190. This represented an increase of 43 per cent in two years and was about ten per cent of all engineering students. Of these 7190 students only 980 graduated and were available - for positions in the industry. That the supply of graduates did not equal the demand can be substantiated by every school dean and by the personnel agents of many mining, metallurgical, and petroleum companies. Some of these companies last summer inaugurated the plan of employing, for the

Jan 1, 1938

By W. C. Ellis

IN an ingot of germanium solidified progressively from the bottom by a method' devised by J. H. Scaff and H. C. Theuerer, examination discloses ex- IH. C. Torrey and C. A. Whitmer, Crystal Rectifiers. p. 364. 1948. New York. McGraw-Hill Pub. Co. tensive twin relationships. A slice taken about midway in a cylindrical ingot approximately 3/4 in. in diameter and 1 1/2 in. in length, after etching and polishing to delineate different orientations, is shown in fig. la. The orientations of the regions designated with letters were determined by Laue X-ray back-reflection methods and plotted on stereograms. The orientation relationships of the designated components were determined by comparing the values for the nine angles between the three respective cube poles of each orientation with the values calculated in a formal treatment of octahedral multiple twinning in cubic crystals. Germanium, diamond cubic in structure, has the octahedral twinning habit. I am indebted to K. H. Storks for the calculation of the angular relationships of cube poles in octahedral twinning to four orders. The set of values for the nine angles is distinctive of the order of twinning. Confirmation for a multiple twin relationship is obtained from the determined indices of the mirror planes. These exist for all orders of twinning through the third and for some of the fourth." If the orientations are not those for twinning, then the nine angles for the cube poles do not correspond in value and distribution to those formally calculated. Since all nine angles must correspond in values and distribution of values to the calculated ones, the Laue method with a precision of one or two degrees is adequate to establish or deny with confidence the existence of multiple twins. Regions of the same orientation can also frequently be identified by the optical reflections. For example, the narrow twin bands in A at 2: 00 o'clock have orientation B1. The interesting twin relationships shown schematically in fig. lb were found for the section in fig. la. Most of this slice was made up of orientation, A, appearing in widely separated regions. Of the four possible first order twins of A, three were present in this slice and are designated by B with subscripts. Four second order twins of A are designated by C with subscripts. It is worth emphasizing that two of these, C, and C,, are second orders of A through the first order missing in this section. Two regions, designated by D with subscripts are third order twins of A. D2 is a sixth order twin of D,. All orientations found were ascribable to multiple twinning, as if the orientations in this section originated earlier in solidification from a single nucleus. The presence of extensive multiple twinning to- gether with the absence of other orientations appears to be a characteristic result in many instances of solidification of germanium. Fertile conditions for twinning probably exist in the array of atoms in the diamond cubic structure. The high order twins in the section shown, it is reasonable to presume, are the result of progressive octahedral twinning through several generations in the material freezing earlier. Some of these generations do not appear in this section, it is suggested, because their orientations with respect to the growth direction were unfavorable for survival. The extensive twinning is probably promoted during solidification by constraint imposed by volume increase, and to an irregular growth front. Twinning may also be due, in part, to the attempt of the solidifying region to attain the orientation most favorable to the growth direction (maximum thermal gradient). The nucleus for a twinned orientation could have its origin in a "stacking fault" on the close-packed octahedral plane. Further work is being done in which the course of twinning throughout an ingot is being studied. The results appear to be important in the general theory of solidification.

Jan 1, 1951

By Larry Kaufman, Martin Schatz

The effect of pressure on the extension of the ? loop in the FeSi system has been determined by means of metallogvaphic studies and hardness measurements performed on a series of high-purity Fe-Si alloys containing 7.5, 11.0, and 13.9 at. pct Si, respectively. These mensurements, performed at 42 kbar and temperatures up to 1200oC, indicate that the ? loop is expanded to about 10 at. pct Si at 42 kbar as opposed to a maximum extension of 4 at. pct Si at 1 atm. Comparison of the experimental results with thermodynamic predictions of the pressure shifts yields satisfnctory results. DURING the past few years, several studies have been performed in our laboratory1-' in order to determine the effect of high pressure on phase equilibrium in pure iron and iron-base alloys. The purpose of these studies has been to elucidate the effects of high pressure experimentally and to compare the observed results with predicted pressure effects derived on the basis of known thermody-namic and volumetric data at 1 atm. These studies have included work on pure iron2,5,7 as well as Fe-Ni,1,5 Fe-cr,l,5 and Fe-c4-6 alloys. In addition, Tanner and Kulin3 have reported results of pressure studies on two Fe-Si alloys containing 2.0 and 6.25 at. pct Si. At the time of this latter study, no detailed information was available concerning the difference in volume between the a (bcc) and ? (fcc) phases in the Fe-Si system as a function of silicon content. In order to compare their observations with calculated pressure shifts, Tanner and Kulin were forced to assume that silicon had no effect on the difference in volume between a and ? iron. The resulting discrepancy between their calculation of the a/? phase boundary at 42 kbar and the observed results led them to the conclusion that silicon additions probably decrease the difference in volume between a and ? iron. Recently: Cockett and Davis8,9 have reported de- tailed studies of the lattice parameters of a series of Fe-Si alloys at temperatures ranging from 20" to 1150°C. These measurements, performed on alloys in the bcc and fcc range, show that silicon does indeed decrease the difference in volume between a and ? iron. By correcting the calculations of Tanner and Kulin in line with the observed effect of silicon they were able to show improved agreement between computed and observed pressure shifts.' The present measurements were undertaken to provide additional corroboration of this effect, by extending the range of composition, in addition to exploring a situation where large extensions of a ? loop could result in impingement of the ? field with an ordered bcc phase (based on Feo.75Sio.25). I) EXPERIMENTAL PROCEDURES AND RESULTS The alloys investigated were obtained from Dr. F. Kayser of M.I.T. They were prepared at the Ford Scientific Laboratory by vacuum melting electrolytic iron and high-purity silicon. The melts were poured under an argon atmosphere into hot-topped steel molds. Subsequently the ingots were hot-worked down to 1/2-in.-diam rods. Three alloys containing 7.5, 11.0, and 13.9 pct Si were studied. Carbon, regarded as the principal impurity, analyzed at, or below, 0.001 wt pct for all of the alloys. Prior to pressure-temperature treatment, the rod was annealed for 24 hr in vacuum at 1000°C, water-quenched, and subsequently machined into 0.100-in.-diam by 0.100-in.-long specimens. Subsequent to machining, the specimens were again annealed and then examined metallographically. They were found to exhibit a clear coarse-grained ferrite similar to Figs. 10 and 110 of Ref. 1 and Fig. 2 of Ref. 3. Subsequently, specimens of each alloy were equilibrated at 42 kbar at various temperatures in supported piston apparatus.1,3,4,6 Three specimens, one of each alloy, were wrapped in platinum and exposed simultaneously. The pressure-temperature cycle consisted of increasing the pressure from ambient to 42 kbar at 25oC, heating rapidly to the desired temperature, holding for 15 min, and quenching to 100°C, followed by slower cooling to 25°C and pressure release. The temperature was measured with a Pt/Pt-13 pct Rh thermocouple which was not corrected for pressure effects. Subsequently, specimens were examined metallographically and by

Jan 1, 1964

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke's Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty's work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke's Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By W. C. Hagel, H. J. Beattie

Seven austenitic alloys of varions base compositions and minor-alloy additions were solution-treated, aged systematically between 1200oand 1800oF, and examined by X-ray and electron metallography. Intragranular preczpitations of µ, Laves, s, ?', Ni3Ti, and x phases were observed as a function of composition and aging time and temperatwre. Phase solubility limits were detevtnitzed within 100Fo intervals. These inter metallic compounds fall into two distinct general classes, and whichever class predomznates depends on base composition. It has become increasingly evident that multicom-ponent austenitic alloys are well characterized by their precipitation processes. Since certain groups of elements act as one, the relationships among these processes are reasonably simple; complete identification of such processes is usually attainable by a systematic aging study with a combination of techniques centered on microscopy and diffraction. Several nickel- and cobalt-base alloys illustrating cellular precipitation and its interaction with general precipitation were reported previously.1 The group of alloys covered in the present paper demonstrates precipitation-hardening reactions involving two distinct classes of intermetallic compounds where the predominating class appears to depend on base composition. This dependency ties in with a crystal-chemistry regularity first observed some twenty years ago by Laves and Wallbaum but never amplified to our knowledge. Results of electron-microscope and X-ray diffraction studies on systematically aged hot-rolled alloys known commercially as S-816, S-590, Rene-41, Incoloy-901, M-308, and M-647 are reported here. Some of these alloys have previously undergone minor-phase analyses by other investiators. Alloy S-816 was investigated by Rosenbaum, Lane and Grant,3 and Weeton and Signorelli.4 Rosenbaum found only CbC in hot-rolled bars. Lane and Grant found CbC and a small amount of M6C in the cast structure and stated that both carbides form during aging, most of the precipitation being CbC. Weeton and Signorelli found CbC, M23C6 and a weak indication of a phase after a slow step-down cooling cycle from 2250°F. Rosenbaum also investigated hot-rolled samples of S-590 and identified CbC and M6C. Preliminary information on Rene-41, gained partly from the present work, was reported by Morris.5 Long-time precipitation phenomena in Incoloy-901 at 1350°Fwere investigated by Clark and Iwanski.B heir raw data re- semble those of our present heat with 0.1 pct B, while their interpretation of these data resembles our interpretation of data from another heat with only 0.001 pct B; they made no statement as to boron content. No previous minor-phase studies of alloys M-308 or M-647 have been reported. EXPERIMENTAL METHODS Table I gives alloy compositions in both weight and atomic percent. Specimens were solution-treated from 1700º to 2200ºF, aged at logarithmic-time intervals up to 1000 hours between 1200 and 1800 F, and examined in accordance with procedures previously described in detail. ' ' Phase extractions were carried out in electrolytic cells containing 800 ml of either 7 pct HC1 in denatured ethanol or 20 pct H3PO4 in water. After electrolysis for 48 hr at 0.1 to 0.2 amp per sq inch, residues were separated by filtration or centrifuging. X-ray powder patterns of residues were recorded on a diffractometer for accuracy and on film for sensitivity. Lattice parameters were calculated by least-squares analyses of indexed sin 8 values, and relative abundances were estimated from intensities of strongest lines of each phase. These phase abundances denote relative amounts with respect to each other rather than to the alloy. Mechanically polished specimens were etched in a freshly mixed solution of 92 pct HC1, 5 pct H2SO4, and 3 pct HNO3. Parlodion replicas for the electron microscope were chromium-shadowed in high vacuum at a glancing angle of 20deg. All electron micrographs are reproduced here with the shadowing source above. The correspondence betweenelectronmicrostructures and phases identified by X-rays was established by a high redundancy of correlation between relative amounts at different stages of aging and examination above and below critical transformation or solubility temperatures. EXPERIMENTAL RESULTS S-816 and S-590—The phases found in S-816 and S-590 after various aging and solutioning treatments are listed in Table 11. These data and the observed

Jan 1, 1962

By J. Wayne Erickson

Hundreds of millions of dollars have been spent to discover or purchase uranium resources that cannot, or should not, be mined with conventional methods if human, natural and financial resources are to be conserved. Three years ago, an industry-supported research stud was initiated to determine whether a safer and more efficient (in terms of cost and environment) uranium mining method could be designed to replace existing techniques. As a result of this study, the "underground in situ" method was conceived and developed to the stage where it is now feasible. This approach involves: (1) sinking a shaft; (2) driving a drift on the ore horizon the length of the ore body; (3) drilling almost-horizontal long holes the width of the ore body; and (4) oxidizing and leaching the uranium drawn from these holes. The method is unique in that the uranium is removed with a minimum of disturbance to the natural hydrology of host or surrounding sands.

Jan 11, 1978

By Vittal S. Bhandary, B. D. Cullity

Swaged iron wire has a cylindrical {001} <110> texture. The texture is also cylindrical after re-crystallization in the absence of a magnetic field, but <111> and <112> components are added to this texture when recrystallization occurs in a field. The mecizanical properties in tension and in torsion are not greatly altered by these changes in texture. AS shown in a previous paper,1 cold-worked wires of the two fcc metals copper and aluminum can be made relatively strong in torsion and weak in tension, or vice versa, by proper control of preferred orientation (texture). The deformation texture can be controlled by selection of the starting texture (texture before deformation), because certain initial orientations are stable during deformation. The present paper reports on similar work performed on bcc iron. In this case it was clear at the outset that there was no hope of controlling the deformation texture, which is one in which <110> directions are aligned parallel to the wire axis. (1t has usually been regarded as a fiber texture, but Leber2 has recently shown that it is a cylindrical texture of the type {001} <110>. In either case, <110> directions are parallel to the wire axis.) There is general agreement on this texture among a large number of investigators, which in itself suggests that the starting texture has no influence on the deformation texture. More direct evidence was produced by Barrett and Levenson,3 who reported that iron single crystals of widely varying initial orientations all had a single <110> texture when cold-worked into wire. Thus <110> is a truly stable end orientation for iron and probably for other bcc metals as well. Under these circumstances attention was directed to the possibility of controlling the recrystallization texture. This texture is normally <110> in iron,4 just like the deformation texture. However, it is conceivable that this texture could be modified by a proper choice of the time, the temperature, and what might loosely be called the "environment" of the recrystallization heat treatment. In the present work the environmental factor studied was a magnetic field. The effect of heating in a magnetic field ("magnetic annealing") on recrystallization texture has been investigated by Smoluchowski and Turner.5 They found that a magnetic field produced certain changes in the recrystallization texture of a cold-rolled Fe-Co alloy. The texture of this material is normally a mixture of three components, and the effect of the field was to increase the amount of one component at the expense of the other two. Smoluchowski and Turner concluded that the effect was due to magnetostriction. With the applied field parallel to the rolling direction, the observed effect was an increase in the amount of the texture component which had <110> parallel to the rolling direction. In the Fe-Co alloy they studied, the magnetostriction is low in the <110> direction and high in the <100> direction. Thus nuclei oriented with <110> parallel to the rolling direction will have less strain energy than those with <100> orientations and will therefore be more likely to grow. In a later paper on the same subject, Sawyer and Smoluchowski6 ascribed the effect to magneto-crystalline anisotropy and made no mention of magnetostriction. In the papers of Smoluchowski et al. the intensity of the magnetic field was not reported but it was presumably large, inasmuch as it was produced by an electromagnet. In the second paper6 it is specifically mentioned that the specimens were magnetically saturated. But if magnetostriction has a selective action on the genesis of stable nuclei during recrystallization, that selectivity must depend only on differences in magneto-strictive strains between different crystal orientations and not on the absolute values of those strains. Thus the saturated state does not necessarily produce the greatest selectivity, because the relative difference in magnetostrictive strains between different crystal directions may be larger for partially magnetized crystals than for fully saturated ones.7 In the present work the specimens were subjected to relatively weak fields (0 to 100 oe) produced by solenoids. MATERIALS AND METHODS Armco ingot iron rod (containing 0.02 pct C and 0.19 pct other impurities) was swaged from 0.25 in. in diam. to 0.05 in., a reduction in area of 96 pct. The mechanical properties in tension and torsion were measured as described previously.&apos; Textures were measured quantitatively with chromium or iron radiation and an X-ray diffractometer,8,1 and

Jan 1, 1962

By C. E. Richards, C. N. Reid

The influence of preferred orientation on the incidence of defbrtnation tuinning has been studied. High-purity iron with almost vandonz grain orientation was cotnpared uitll iron of the sa)ne grain size and composilion lza,ing a strong (110) fiber texture. As expected from published work on single crgslfls, /he ))lean stress for the onset of luitzning-, and the l,olu)nt. fraclion of twinned nzaterial obserlled in lension differed fron the 1-a1ue.s it2 co?nPression for tnolerial with a slrong texlure. The llinning stress of "rctndorrl " )zalerial did not 17ary with the sense of the aPPlied unin.via1 stress, but sirprisinglg the incidence of 1c)i)zning- was about three 1i))zes greater ill conzp?&apos;ession Illon in lension. These results (Ire attributed entirely to ovienbation and may be nderslood in ler?ns of the shear slresses acting on the allowed twinning syster)is. J. HE twins most commonly formed in bcc metals may be described as regions of the crystal in which a particular set of (112) planes is homogeneously sheared by 0.707 in the appropriate ( 111) direction. A similar twin-related crystal could be produced by a shear of 1.414 in the reverse (111) direction but twinning by this large displacement has never been reported. Thus, twinning is unidirectional and a shear stress which produces twinning does not do so when its sense is reversed. The sense of a shear Stress is reversed when the loading is changed from tension to compression, or vice versa. Consequently, for a given orientation of a crystal relative to a uniaxial stress, only a fraction of the twelve (112) twinning systems are geometrically capable of operating in tension, and the remaining systems may operate only in compression. Therefore, when twinning is involved, there are expected to be differences in behavior between crystals tested in uniaxial tension and those tested in compression. This has been verified experimentally by Reid et 01.&apos; and Sherwood el al.,&apos; although a critical stress criterion was not encountered. Furthermore, twinning stresses in colmbium," tungten, tantalum,&apos; irn,&apos; i-Fe,\ nd molybdenum7 single crystals have been shown to depend critically on orientation, although again twinning did not occur at a critical value of the macroscopic shear stress. However, when twinning occurs, it generally does so on the most highly stressed systems, 1--4&apos;6&apos;8&apos;9 implying that the stress level does have some relevance to twin formation. In view of the large orientation dependence of twinning in bee single crystals, it might be expected that such an effect would be present in poly crystalline material which possesses a recrystallisation texture. Indeed, riestner" showed that the twinning stress in tension is very orientation-sensitive it1 <&apos;grain-oriented, silicon-iron;" this material possessed a very strong t c m^ii a nnr x_____k . i-_ii__ ri_______j. _x r»i_._:__i preferred orientation obtained by secondary recrystallisation. Reid et a/.&apos; observed a marked difference in the tensile and compressive yield stresses of polycrys-talline columbium which was rationalised in terms of the effect of a preferred orientation on twinning. No other such illformation is known to the authors. Several investigations of twinning in polycrystalline bcc metals have been reported in which the possible existence of a preferred orientation was not even mentioned. It is the purpose of this paper to show that there is a strong effect of texture on twinning in polycrystalline iron, and to poilt out the difficulty in eliminating preferred orientation in recrystallised metals. 1. EXPERIMENTAL METHOD Material and Specimen Preparation. Low-carbon, high-purity iron was obtained from the National Physical Laboratory in the form of $-in. diam rod which had been cold-swaged from a diam of 1 in. The composition of the material is given in Table I. The as-received bar was cold-swaged directly to 0.185 in. diam from which cylindrical tensile and compression specimens were machined. Specimen geometry is illustrated in Fig. 1. The gage length was 0.30 in. long and 0.10 in. diam; it should be noted that, apart from the extra heads which are necessary for tensile loading, the geometry and dimensions of the two types of specimen are identical. The specimens were heat treated either by sequence A or B outlined in Table 11. The essential difference between these two treatments is that in one case the material was repeatedly cycled through the y- to a-phase change in order to produce grains of almost random orientation ("random" iron)

Jan 1, 1969

By John B. Hastings

Ten miles from Hartsel, near Antelope springs, in Park county, Colorado, there is a large area of unconsolidated lake-beds, which are interesting because at least a part of the lacustrine sands contains in the aggregate an immense amount of gold. During 1906, one of the arms of this dessicated lake was fairly well prospected with shafts and cuts by an Eastern company to test its value, as favorable amounts of gold had in some instances been found upon it. The claims of the company contain about 5,000 acres of the beds; bat this is only a small portion of them, a south branch from a main body, which is at least 7 miles in diameter, with other and very wide lateral gulches, paralleling the one herein described on the east and west. A certain amount of digging and sampling was done in the outside areas; but the result was evidently unsatisfactory, since the work was discontinued. This section of Colorado has not been studied geologically, and the age of the ancient lake is unknown. It is probably Quaternary. I spent two weeks on the ground, in September

Jan 1, 1909

By W. A. Turcotte, A. D. Paananen

Introduction The large reserve of fine grained oxidized iron-formation at the Tilden mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Due to the nonmagnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden, ore body have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of desliming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions. Development of selective flocculation-desliming was a key to commercialization of the process. Operations started in late 1974 with Algoma Steel Corp. Ltd., J & L Steel Corp., The Steel Company of Canada Ltd., Wheeling-Pittsburgh Steel Corp., Sharon Steel Corp., and The Cleveland-Cliffs Iron Co. as participants. Cleveland-Cliffs operates and manages the operation. Development of the Tilden Flowsheet The geology and ore reserves of the Tilden mine have been detailed in a paper by Villar and Dawe (1975). A joint program was undertaken in 1961 with the US Bureau of Mines in Minneapolis using the flowsheet developed by the Bureau employing the selective flocculation-desliming and calcium activated anionic silica flotation method (Frommer, et al, 1966; Frommer, 1964; Frommer, Wasson, and Veith, 1973). During this time, parallel testing at Cleveland-Cliffs Research Laboratory and Pilot Plant centered on the same type of desliming but was followed by the cationic flotation of silica with amine collectors (Columbo and Jacobs. 1976). The cationic silica flotation system was eventually chosen for its overall efficiency and simplicity. Regardless of the flotation method chosen, the technique of selective flocculation-desliming prior to flotation is the key to the success of the process. The flowsheet is described in detail by Villar and Dawe (1975). [Figure 1] shows a simplified one-line flowsheet of the Tilden concentrator. A total tailings thickener has been added to the original flowsheet and was placed in operation in 1978. The total-tailings thickener overflow reports to the reuse water pond and the underflow is pumped approximately 8 km (5 miles) to a storage basin. A flowsheet of the reuse water system is shown in [Fig. 2]. Selective Flocculation-Desliming Data have been published on the mechanisms and factors affecting selective flocculation in iron oxide-silica systems. The intent of this paper is not to discuss the theoretical aspects of selective flocculation, but rather to present experience gained from the commercial Tilden operation and from bench and pilot plant testing of fine-grained oxidized iron ores. From the bench and pilot plant testing prior to plant startup, certain reagent combinations and rates for the commercial Tilden plant were established. In the experience gained from three years of plant operation at Tilden, some of these reagent dosage rates have required significant adjustments due to changes in reuse water quality and to meet the requirements of varying ore types. Reuse Water The process water quality is a major concern at the Tilden mine and is constantly being monitored for selected chemical and physical characteristics. This monitoring has continued on a regular basis in order to gain a more thorough understanding of the interactions taking place in a dynamic water system and particularly as water quality is influenced by seasonal variations. Control of the reuse water chemistry is essential to the Tilden process both in the selective flocculation-desliming and flotation stages of concentration. With roughly 75% of the reuse water used in grinding-desliming operations, it is readily apparent that the biggest "reagent" in the selective flocculation-desliming process is water. Not enough can be said about the close control that must be exercised on the overall reuse water system. Control of the chemical treatment of the feed to the total tailings thickener is of utmost importance in order to produce a reuse water for the concentrator that is compatible with all stages of the concentrating process. There are many analyses made which aid in judging the quality of the water. Some of these are shown in [Table 1]. Five are particularly important and are monitored daily so that reagent adjustments can be made as required: suspended solids, calcium hardness, pH, dissolved silica concentration and temperature.

Jan 1, 1981

By AIME AIME

WHEN Vice-chairman Calvert Townley calls the next meeting of the Executive Board of the American Engineering Council of the Federated American Engineering Societies to order in Washington on Sept. 30, it will be the first meeting in that city for almost a year. It is probable that the Board will decide at this meeting whether future board meetings will be held regularly at the headquarters in Washington or whether the plan of meeting at various engineering centers throughout the country, as has been done during the past year, will be followed. The most important business coming before this .meeting will be the election of a president to succeed Herbert Hoover, who resigned after he became Secre¬tary of Commerce. Nominations to fill this vacancy were ordered &apos;at the last meeting of the Executive Board, to be reported at the September meeting. Special attention will be given the plans for the engineering assembly, extension of employment service, question of licensing and registration of engineers. The engineering assembly, committee has been appointed, with A. P. Davis as chairman, the other members being Philip N. Moore, L. P. Alford, John C. Hoyt and F. A. Vaughn. This committee will work out detailed plans for an assembly to be held in con¬junction with the annual meeting of the American Engineering Council in, January. Tentative plans provide for a three-day session; one day to be given to special meetings of the executive boards of member organizations and committees of the American Engineering Council; one day to the sessions of the American Engineering Council; and at least one day to discussion of some, special topic.

Jan 1, 1921

By H. P. Leighly, F. C. Perkins

THERE have been several statements in the literature about the difficulty of producing single crystals of high-purity (99.99pct) by the strain-anneal method. Consequently, investigators tend to employ low-purity aluminum for their single-crystal experiments, or else resort to the Bridgman or other techniques which depend on solidification for the production of single crystals. The following paragraphs describe a solid-state method for the manufacture of single crystals of high-purity aluminum which should provide crystals with greater perfection than those formed by solidification. The starting material for this method of producing single crystals was secured from the Aluminum Corp. of America and has a purity of 99.99 pct, the balance being trace amounts of impurities. Specimens approximately 1 by 4 in. are sheared from sheet having a nominal 0.050 in. thickness. The specimens are given a preliminary anneal at 640°C for approximately 3 hr in order to remove fabrication strains and to produce an average grain size of about 1/4-in. diam. The specimens are then etched in Tucker&apos;s etchant (45 pct HC1, 15 pct HNO3, 15 pct HF and 25 pct H2O) to remove the oxide film. Critical strain is applied by wrapping each specimen about a 1 3/4 in. round and subsequently straightening it against a flat surface. The high-purity aluminum sheet is sufficiently soft that this operation can be accomplished by ordinary finger pressure. The specimens are immediately annealed again at 640°C for 3 hr and reetched for examination. Ordinarily, considerable growth of certain of the grains will have occurred, and occasionally a single crystal will be produced on the first attempt. The procedure of alternately straining, annealing and etching is repeated until the majority of a batch of specimens contains usable crystal sizes. Typical examples are illustrated in Fig. 1. The greatest changes in crystal sizes are produced in the initial treatments. As the average crystal sizes get coarser in the later treatments, the sever- ity of the strain must be increased in order to produce grain boundary- migration. This increase in severity is effected by decreasing the diameter of the round used for straining (to 1 1/2 in., for example) and/or wrapping the specimens about the round twice, with opposite faces in contact with the round, before flattening. Usually the strain treatments described are not severe enough to produce nucleation in coarse grain high-purity aluminum. The growth of grains occurs by strain-induced grain-boundary migration. It has been observed that the grain boundaries move most readily during the first hour or so of each annealing treatment and that the rate of movement decreases with extended holding times at temperature. Prolonged annealing treatments are therefore not usually beneficial. Similarly, the rate of growth of each crystal appears to depend upon the orientation of the crystal with relation to those of its neighbors. Frequently island grains are formed after the initial heat treatment as the result of slow grain-boundary migration. These sometime become stationary during later heat treatments. Twin orientation interfaces are frequently developed during annealing. These imperfections can usually be removed by increasing the severity of strain to produce actual nucleation of new grains of more favorable orientation at the imperfection interfaces. The largest single crystals produced in our laboratory by the above method measured 4 by 1 by 0.050 in. Examination of Laue back-reflection patterns from a limited area of the specimens, gave no evidence of polygonization. Probably there is some indication of polygonization in the original grain area provided a more sensitive technique is used for detection. Experiments to produce wider specimens were less successful, possibly because wider sheets increase the complexity of the strains induced by deformation and promote widespread nucleation. Grain boundary migration occurs preferentially in a direction parallel to the longitudinal axis of the specimen. The choice of specimen geometry with respect to the rolling direction of the sheet appears to be immaterial in regard to the production of single crystals.

Jan 1, 1961

By C. E. Barnett, G. R. Durland

LUMINESCENT materials have been used in an increasing variety of ways in recent years. Such uses range from the screens on which the picture or image is presented in television and other cathode ray tubes to fluorescent lamps, fluorescent effects in decorative, theatrical, and display lighting, and the many applications of phosphorescence in paints, textiles, paper, and plastics. During the war the screens for a radar set or the "night-seeing" devices were not fundamentally different from those in other cathode ray tubes, but nevertheless they presented special problems for the phosphor manufacturer. It was essential that the "pips" on a radar screen continue to glow after the exciting beam had swept on, but this afterglow would be ruinous to a television screen. In the image tube used for seeing at night with infrared instead of visible light, electrons emitted by an infrared-sensitive receiving surface were amplified and converted to visible light after striking a fluorescent screen. The small size of the screen caused special problems in reducing the grain size of the phosphor to obtain adequate resolution. Other devices used phosphor surfaces which could be stimulated directly by infrared radiation to emit visible light. Energy was stored in the phosphors by prior excitation with short-wave-length radiation, and the stored energy released on subsequent exposure to infrared radiation. Maps, navigational charts, bombing manuals, and computers of various sorts were printed on fluorescent paper or lettered with fluorescent inks. Fluorescent markings excited by small ultraviolet lamps were used on airplane instrument dials. A large amount of research was done to determine the best color for the emitted light and other properties for the fluorescent materials, and on the best methods for their fabrication into the items listed above. Phosphorescent materials found wide use during blackout restrictions to mark safe passageways, to delineate traffic hazards, to identify packages, and to mark tools and other items of equipment.

Jan 1, 1948

By Alan Morris

THE investigation of the hot-working properties of metals and alloys furnishes a problem which has been attacked in many ways. Tensile, impact and hardness tests on heated specimens have furnished interesting data, but in most cases either the tests are difficult to make or the results hard to translate into terms of practical value. Some investigators have used the drop hammer to advantage. It furnishes a rapid and simple method of comparing the plasticity of metals at elevated temperatures. The indications obtained by its use are of value only in so far as their significance is understood and they can be intelligently used to predict the behavior of a given metal under given hot-working conditions. The work reported here was undertaken not only to add-something to the existing volume of such data but also to contribute to our understanding of the results. Doerinckel and Trockels1 used cylindrical specimens and determined the work required to reduce the specimen to one-half the original height. Ellis2 studied the effect of constitution on the malleability of steel at high temperature. His method and that of Kent3 were similar to the one used in the present work. The tests described by Kent were made on samples of tin, zinc, aluminum, copper, lead, 70:30 and 60:40 brasses, with and without a small quantity of lead. He concluded that the test would "indicate whether a material can be forged at a given temperature without cracking." This interpretation must be used with caution. While it is probably true within limits, one must consider the severity of the forging operation. Again, it will not apply strictly to forms of hot working other than forging. For instance, an alloy running 61.0 per cent. copper, 3.25 per cent. lead, remainder zinc, will crack badly in the test, yet it is extruded commercially. When the possibility of hot-working a new alloy is being considered a study of its drop-hammer test should help

Jan 1, 1931