Search Documents

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at subcritical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.1 Westgren, Phragmén and Negresco2 identified the following carbides in chromium steels: [Cementite Fe3C (containing up to about 15 per cent Cr) Trigonal carbide Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide Cr4C (or Cr23C3) (containing up to about 25 per cent Fe) Orthorhombic carbide . Cr3C2 (containing only a few per cent Fe)] The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus.4 By means of dilatometric and microscopic studies, sections of the diagram were established. This diagram showed the presence of the special carbide Cr7Ca in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in r per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7Ca occurs in chromium steels containing more than about 1 per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. EXPERIMENTAL PROCEDURE The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into 1-in. round bars, and all heat-treatments were conducted on specimens of this section .size. Sections of the bar stock 8 in. long were hardened in air, oil or water depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after auenchine. The quenched bars were cut into

Jan 1, 1942

By Thomas G. Murdock

EthIopia, the first country to be liberated from Axis domination, has recovered remarkably from the ravages of occupation and war. Mineral production has contributed significantly towards this recovery, as it has provided a means of obtaining foreign exchange and has given employment to hundreds of workmen whose maintenance otherwise would have presented a problem. Although primarily an agricultural country, never with a large mineral production, Ethiopia has within its borders a variety of minerals, both precious metals and nonmetallics. Some of these are important to the country as a national asset and others contribute greatly to local economy and can be expected to do so even to a greater extent in the future1 (Fig I). Physiography and Geology The Empire of Ethiopia is essentially a mountainous and volcanic country, in northeast Africa, situated principally between latitude 4° and 15°N and longitude 34° and 44°E. It is bounded on the north by Eritrea, on the northeast by French Somaliland, on the southeast by Italian Somaliland, on the south by Kenya Colony, and on the west by Anglo-Egyptian Sudan. These European possessions thus completely surround the country. Its access to the Red Sea is through Eritrea; to the Gulf of Aden, through French or British Somali- land ; and, to the Indian Ocean, via Italian Somaliland. These routes range in length from 40 to 250 miles. Ethiopia has an area of approximately 350,000 square miles, with a width from north to south of 625 miles, and a maximum length from east to west, along latitude 8°N, of about 875 miles. Physiographically the country is characterized by two very extensive sub-tabular plateaus: the Ethiopian Plateau to the northwest and the Somaliland Plateau to the southeast, separated by a long tectonic graben—the Rift Valley of the Galla Lakes and Danakil. The Ethiopian Plateau, deeply cut and notched by the drainage, slopes in a general northwest direction toward the Sudanese Plains and the valley of the Nile; the Somaliland Plateau slopes to the southeast, toward the Indian Ocean. The valley of the Galla Lakes and its extension to the northeast—the Awash River Valley, separates the plateaus, from Lake Rudolph to Danakil. This depression which constitutes a continuation or ramification of the Great Rift Valley of Central Africa joins in turn the trough of the Gulf of Aden and the Danakil-Eritrean Rift, continuations of the Red Sea and the Jordan Valley. The general basement of Ethiopia is made up of very old rocks, usually considered as Archaen.2 These rocks are represented by the metamorphic crystallines, such as gneisses, different kinds of schists, included lenses of crystalline limestone, and massive intrusives such as granites, diorites, and syenites, all cut by

Jan 1, 1949

CONTENTS PAGE UREN, LESTER C.-Increasing Production of Petroleum by Increasing Diameter of Wells. Discussed by A. Beeby Thompson 1 LAHEE, FREDERIC H.-Comparative Study of Well Logs on the Mexia Type of Structure. Discussed by W. A. I. M. van Waterschoot van -der Gracht.... 4 Increasing Production of Petroleum by Increasing Diameter of Wells Discussion of the paper of LESTER C. UREN, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1364-G, with MINING AND METAL-LURGY, October, 1924. A. BEEBY THOMPSON, London, Eng. (written discussion).-The subject discussed in this paper has long been debated by operators in European fields, where very strong views are held regarding the advisability of controlling gas pressures by shutting in wells. While unwilling to theorize on the subject of restricted flow, the writer has always been disposed to associate himself with those who hesitate to impose any obstruction to a natural transitory state that breaks up the oil-containing strata and establishes a feeder system which no subsequent events, natural or artificial, can approach in intensity. In both Russia and Roumania, where the oil is concentrated in discontinuous, disturbed, and irregular lenticles of sand varying, within short distances, in coarseness of grain, extent of impregnation and degree of cementation, it has been the practice to let the wells run wild in order to provoke disruption of strata. By encouraging violent eruptions, an extended feeder system is created and the ejection of enormous quantities of sand, rock, and clay creates a sump and seepage area that it would be difficult to imitate by any artificial means, not excluding actual mining. Before discussing the somewhat novel method suggested for enlarging the infiltration area, the writer would like to confirm the fact that many valuable data applicable to oil are forthcoming from a study of water phenomena. Long association with water-supply problems in many parts of the world has shown how closely the phenomena of underground movements of water and oil are related, so that it is pleasing to note the author's use of water formulas. But there is one great distinction;

Jan 7, 1925

By John A. M. E. Church

AT the last meeting of the Institute, a discussion arose upon the question, " Is them pressure in coke ovens ?" and many of the members seemed to think that the superiority of the Belgian furnace might be due to the fact that it is a completely closed chamber, in which the gases given off by the coal are, or may be, at more than the atmospheric pressure. It seems to me that this position is untenable, and that an examination of one of these ovens in operation will show, not only that there is no excess of pressure in the coke chamber, but that the contrary is true, and a partial vacuum exists. The Belgian or François oven consists of a rectangular chamber closed at the ends by sliding doors, and furnished with flues in the side walls and floor. The new charge is introduced at a time when the furnace is so hot as to cause immediate and copious discharge of the volatile constituents of the coal. The gases pass downwards through the side flues giving out their heat to the walls and thus to the coal. Underneath the floor air is introduced and the gases burn, producing intense heat. Heat is also reflected from the arched roof upon the coal which is therefore heated from all sides. The especial advantage which this construction was designed to secure is that no air is admitted to the coke-chamber. All the heat is produced by the combustion of the uncokeable gases, and the yield ought to be a maximum. It is so in fact, allowing for the imperfections inseparable from furnace construction and management. Sometimes the yield is in excess of the percentage indicated by assay, showing that

Jan 1, 1873

Discussion of the paper of N. V. Hansell, presented at the Cleveland Meeting, October, 1912, and published in Bulletin No. 72, December, 1912, pp. 1497 to 1,517. C. Q. PAYNE, New York (communication to the Secretary*) :-Mr. Hansell has presented in his paper a very interesting and valuable summary of the various methods of enriching iron-ores which have been developed during recent years. Particularly striking in this connection is the high degree of enrichment of the concentrates from magnetic iron-ores which is now commercially feasible. Magnetic concentrates containing from 6 7 to 139 per cent. of metallic iron, showing an efficiency of 90 and even 95 per cent. in. their separation, are not now uncommon. Such results exceed those obtained by gravity methods of treatment of all copper-, lead-, and zinc-ores, and are only equaled in the cyaniding of gold-ores and in the flotation treatment of certain copper-ores. It is of interest to note that the-type of magnetic field which is employed in securing these results, in the Gröndal (wet) and the Ball & Norton (dry) systems of treatment is the same in each case : viz., a field of alternating north and south poles. The credit for developing this simple and useful field, which has found so wide an application both in this country and abroad, is due to two American inventors and engineers, Clinton M. Ball and Sheldon Norton. At the same time, it should be noted that part of the improvement in the grade of the magnetic concentrates, especially in the case of the wet treatment of finely mineralized ores, is due to a well-devised scheme of mill-treatment, whereby a rough concentrate is usually obtained as an intermediate product, which is then recrushed and reseparated in obtaining final clean products.

Jan 3, 1913

Discussion -of the paper of I. N. KNAPP, presented at the New York meeting, February, 1915, and printed in Bulletin No. 96, December, 1914, pp. 2783 to 2793. A. C. LANE, Tufts College, Mass.-Is there any noticeable effect in drilling against salt water? Mr. Knapp says that the mud settles very quickly when brine is added-. What is the effect when you strike a strong salt water ill boring? I. N. KNAPP.-You are supposed to have enough mud pressure in your well to keep the saltwater out. I have drilled against what I knew to be 80 ft. head of water, and hot water too at 99.5°; this water did not show until the well was bailed and the mud pressure reduced. HENRY Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).-Mr. Knapp may be interested to learn that the use of mud in drilling through porous strata is much older than lie appears to be aware of. It has been used notably by Honigmann for boring shafts in Holland and in some of the adjoining portions of Germany. At the Oranien Nassau colliery, shafts about 12 ft. in diameter and 425 ft. deep were sunk in. this way-namely, by boring with a rotary borer, a thick mud puddle being pumped into the shaft, so as to maintain a pressure in the shaft greater than the hydrostatic pressure in the surrounding loose sands and thus keeping the sides of the shaft from collapsing. He will find references to this method in Das Abbohren von Schächten; Handbuch der Ingenieurwissenshaften, p. 134, also in the Transactions of the Institution of Mining Engineers, vol. xiii (1896-97), p. 155. The process appears to have been employed even before 1895, though I cannot give the exact date when it was first used.

Jan 5, 1915

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951

By B. F. Decker, J. H. Keeler, W. R. Hibbard

Textures of hot-rolled, of cold-rolled, and of cold-rolled and annealed zirconium sheets were determined by use of an X-ray spectrogoniometer. All textures showed a tilt of the basal planes 240" from the rolling plane about the rolling direction. Deformation textures showed the [1010] direction to be approximately in the rolling direction. After recrystalliza-tion, the 111201 direction was approximately in the rolling direction. This texture was sharpened by annealing above the allotropic transformation. Textures of sheet produced by alternately cold rolling and then annealing were less strongly oriented than sheets that underwent severe deformation without intermediate anneals. THIS study of the deformation and annealing textures of high purity zirconium was carried out to supplement an investigation of zirconium and zirconium-base alloys. The spectrogoniometer method of pole figure determination was used and yielded more detailed and precise information than the photographic techniques used by previous investigators. Earlier investigations of the rolling textures of hexagonal metals titanium,1,2 beryllium," and zirconiumL having a c/a ratio slightly less than 1.6 disclosed a rotation of the basal planes from the rolling plane about the rolling direction so that the basal poles were inclined toward the transverse direction, and with one exception,& the [1010] direction was found parallel to the rolling direction. Similarly, hot rolling produced a spread of the basal poles in the transverse direction,2,3,5 With the [1010] direction parallel to the rolling direction. The textures of these metals after recrystallization differ somewhat from each other although still exhibiting the transverse rotation of the basal poles about the rolling direction. Zirconium" was found to have the [1120] direction in the rolling direction, beryllium" continued to have the [1010] direction in the rolling direction, and titanium' was shown to have the [1010] direction in the rolling direction (the cold-rolling texture) when annealed at 1000°F, changing to the [1120] direction in the rolling direction when annealed at 1500°F. It was suggested2 that the titanium retains the deformation texture after re-crystallization, and preferred grain growth at higher temperatures produces the second texture. Annealing above the allotropic transformation temperature did not appreciably change the high temperature recrystallization texture for titanium.' Coarsegrained zirconium showed more spread" in the transformation texture than in the recrystallization texture. The material used in this investigation was crystal-bar zirconium prepared by the iodide process. The major impurity was hafnium which was less than 0.3 pct. The composition obtained by spectro-graphic analysis is given in Table I. The hot-rolled specimen was prepared from a 50-g button of zirconium arc-melted in a water-cooled crucible under an argon atmosphere. This button was enclosed in a welded sheath of soft iron and the ensemble was rolled at 825°C. After each pass the sheath was put back into the furnace to allow it to return to the desired temperature. The zirconium ingot was reduced in this manner to a thickness of about 0.035 in., a reduction of approximately 90 pct. The sheet after removal from the sheath was alternately polished and etched to a thickness of 0.001 in. Cold-rolled specimens were prepared from crystal bar by a series of reductions of approximately 0.010 in. until the sheet reached a thickness of 0.010 in. after which it was cold-rolled to 0.001 in. thickness between sheets of alloy steel. The total cold reduction amounted to about 99.8 pct. Specimens were annealed in an evacuated Vycor or quartz tube. The transmission pole figures were obtained by the quantitative method of Decker, Asp, and Harker6 modified by Geisler7 using an X-ray spectrogoniometer with Cu Ka radiation. Unless otherwise specified all four quadrants were examined with 5" increments along the radius of the pole figure. Absorption corrections were made for changes in length of the X-ray path through the sample as inclination of the

Jan 1, 1954

By Peter M. Fozzard

The San Bartolomt silver deposit was discovered by a United Nations team of geologists working with a counter- part team of staff of the Ecuadorian Government's General Directorate of Geology and Mines (DGGM). The Phase I project over five areas of operation during which this discovery was made was financed through a United Nations Development Program contribution of $860,000 and an Ecuadorian Government participation of about $680,000 equivalent. Existence of mineralization at San Bartolomé was first recognized in 1966 when a reconnaissance geochemical stream-sediment program was carried out over a 10 500 km2 (4,054 sq mile) area centered around the city of Cuenca in southern Ecuador. Over the course of this project more than 10,000 samples of stream-sediment, soil, and rock materials were collected. Average costs per sample were $10.00, as follows: collection, $5; sample preparation, $1.60; assay work, $3.40. Initially in the program (1965-1966) sediments were collected along all motorable roads and tracks. Routine analyses, originally by colorimetry and later by AAS, were for Cu, Pb, Zn and occasionally As, Ni, and Co. Discovery geochemical samples from the San Bartolomé drainage area were among the first to be taken in 1965. As luck would have it, the road along which this traverse was taken passes only some 100 m (328 ft) downstream from the mineralized suboutcrop. The relevant two streams sampled are of inconsequential size, some 1 m (3.3 ft) in width, with a limited flow volume throughout the year. Original anomalies were recognized through cold-extractable Cu/Zn analyses. The pH of all river waters was also recorded at sample sites. Resampling the discovery sediments when AAS became available showed total extractable values of between 150 ppm-300 ppm Zn, 550 ppm Pb, and 10 ppm Ag. In 1967 the first followup was by rough-and-ready means. Dithizone field-kits (THM) were used to rapidly test soils from the surrounding area. The area has no outcrop. This work allowed the definition of an area of interest of some 2 km (1.2 miles) x 500 m (1640 ft). Six approximately 1 km (0.6 mile) to 1.5 km (0.9 miles) lines spaced at approximate 250 m (820 ft) intervals were established and used for IP surveys and soil sampling at 50 m (164 ft) intervals. Where one of the lines crossed the westernmost geochemical discovery creek a first-priority geophysical anomaly coincided with a major Zn/Pb (and later Ag) soil anomaly. A pit was sunk and encountered mineralized vein material at a depth of 1.5 m (5 ft). This lucky glory hole confirmed the geochemical discovery and prompted systematic followup. Immediately, costeaning of the west bank of the discovery creek, the Quebrada Ocashuaico, was carried out and exposed weathered and leached mineralization. Nearly 100 mineralized veinlets ranging in thickness from 0.5 cm (0.2 in.) to 8 cm (3 in.) were exposed across the 180 m (59 1 ft) costean. Sixty mineralized veinlets were determined over a 90 m (295 ft) wide zone. Sampling delineated minable widths averaging between 0.16 and 0.31 kg/t (5 and 10 oz per st) Ag with associated copper (very sporadic) lead and zinc. Over the period 1968- 1972 a considerable amount of detailed work was completed: detailed IP, EM Turam, magnetic and mise-a-la-masse geophysics, very detailed soil- sampling, trenching, drilling and glory-hole drifting, and cross-cutting. Numerous problems were encountered: the area was found to be a most difficult geoelectrical target; zero outcrop; pyrite (nonargentiferous zones) associated with faulting; mineralized groundwater; extensive clay development; loss of diamond drill-core, and no two-dimensional surface information. As the program developed the complexity of the structure was slowly unravelled, using a degree of good guesswork. Apart from photogeological and ground geological mapping at various scales, the following

Jan 1, 1985

By Elton A. Youngberg

J. H. HEARDING, Jr.*—Extremely hard ferruginous chert (taconite) was encountered in driving a drift at the Fraser underground mine near Chisholm, Minn., on the Mesabi Iron Range. In order to get better results in drilling in this ground, it was decided to try tungsten carbide bits. In the beginning, 1½ in. tungsten carbide bits and 1 1/8 in. round-lugged alloy steel drill rods with "jack-stud" inserts were used. Considerable difficulty was encountered because the jack-stud became loose in the drill rods. Because there was not enough alloy steel drill rod on hand, we began to insert jack-studs in the ordinary high carbon drill rods and found, to our surprise, that there was less trouble with jack-studs working loose in these rods than there had been with the alloy steel rods. As a result, use of the alloy steel rods has been discontinued entirely. Under the heading "Drilling Procedures" the statement is made that all holes are started with detachable bits or conventional steel to prevent undue strain on the tungsten carbide bit inserts when collaring a hole on uneven ground. This practice was followed in our work originally for the same reason. It was soon found, however, that the holes could be started with the tungsten carbide without injuring the inserts if the drill operator was careful and did not give the drill too much air until the bit had a chance to seat itself in the rock. J. C. FRANZ*—In a discussion of other technical papers with reference to percussion drills and the use of carbide tungsten bits, it was my impression that the authors reported one of the first difficulties experienced with the use of standard, conventional percussion drills, was insert bit failures due to crushing of the bit inserts when the bits became dull. During the past few years, some of the rock drill manufacturers, I am told, have adopted an air drill for use with the carbide bits that have a lighter blow and faster rotation than the regular machine. This machine has been tested and the carbide bit failures have been considerably reduced. L. W. DUPUY†—The difficulties Mr. Youngberg mentions that were had with rod and coupling breakage call to mind similar troubles experienced at the Picacho mine in California near Yuma.6 The commercial couplings then available were found to be tempered almost to brittleness. Rod breakage was usually in the threads near the end of the rod. The highly-tempered couplings would break as soon as the rod broke. The solution was to thoroughly anneal the couplings and to put in only a very mild temper. Subsequently the alloy used in making the couplings was changed from the original by the manufacturer, but still only a very mild temper was used. The result was that the softer coupling would give but would not snap and release its hold on the broken rod thread. Fishing jobs were reduced to the few where the rods broke at the rod end of the thread. Thread breakage on the rods was further reduced by thorough annealing prior to tempering. The data Mr. Youngberg presents regarding the use of carbide inserts on long blasthole drilling is most interesting and it would appear that the use in this manner of percussion drills and carbide bits will have many applications. W. M. WOODWARD*—How many feet of hole, on the average, do you get from a tungsten carbide bit, and is there much variation from this average? E. A. YOUNGBERG (author's reply) —In recent months the 2 in. tungsten carbide bit footages in long hole drilling hake varied from 115 .to 140 ft monthly. The footages obtained from individual bits vary from several feet to over 300 ft, however the life of a majority of the bits will be within 25 ft of the average.

Jan 1, 1950

By H. H. Kaveler, W. R. Evans, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By W. R. Evans, H. H. Kaveler, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By M. L. Hammond, G. M. Bowers

Silicon dioxide films have been prepared on silicon wafers by the oxidation of SiH, near 400°C. Results previously reported by Goldsmith and Kern7 have been qualitatively corrobovated using a system of different geometry, and significantly greater deposition rates have been achieved. The deposition rate is independent of thickness and nearly independent of the O2/SiH, ratio over a wide range; however, the rate is strongly temperature-dependent. The structure of the deposit depends upon the cleanliness of the substrate, and the electrical field strength of the deposited oxide depends upon the nature of the electrodes. MULTILEVEL interconnects in integrated circuits using aluminum metallization require an insulator that can be deposited at low temperature. Because the A1-Si eutectic is only 577°C, the maximum deposition temperature must be below about 500°C to prevent reaction of the aluminum with the silicon and with other materials in the integrated circuit. Many methods of depositing insulating films of SiO, and other dielectrics have been reported'-6 but the technique described by Goldsmith and Kern7 offers the simplest method of preparing SiO, films. The technique involves the reaction of SiH, and 0, to form SiO, films in the 300" to 500°C temperature range. Previous work using this gas system has been reported8 and the initial development work at Philco Microelectronics was done at the East Coast R&D Laboratories. 9 This paper corroborates some of the results of Goldsmith and Kern,7 shows that much higher deposition rates can be obtained than previously reported, and presents some observations on the structure of deposited SiO, films. EXPERIMENTAL CONDITIONS Fig. 1 is a schematic drawing of the apparatus used in this study. It differs from that of Goldsmith and Kern in that 1) the gases are mixed before they enter the reaction chamber, 2) there is no fritted glass diffuser, and 3) the wafers are stationary during deposition. The control thermocouple was in a well located 0.06-in. from the substrate, and three gas supplies were used: 1 pct SiH4 in N 2, O 2, and N 2. Water vapor must be excluded from the plumbing to prevent the formation of colloidal SiO, and the SiH4 must be diluted with an inert gas because SiH4-0, mixtures are extremely flammable above about 4 pct SiH The wafer temperature was determined by attaching a thermocouple to a test wafer and the temperature was maintained to +5 C. The conditions used in this investigation are listed in Table I. The temperature range was chosen for compatibility with the A1-Si system. The volume ratio of 0, to SiH4 is the actual volume of 0, delivered to that of SiH4, taking into account the initial dilution of the SiH4. This ratio, which was used by Goldsmith and Kern,7 is a useful indicator of the experimental conditions. The active/inactive ratio is the ratio of the volume of active gases, SiH4 and O2, delivered to the volume of dilution gas. The active/inactive ratio is an important parameter to specify for deposition rate determinations since it determines the amounts of reactants that arrive at the sample per unit time. Fairly high dilution ratios were necessary to achieve uniform deposits of SiO,. Most of the process characterizations were performed on the polished (111) face of 3 to 5 ohm-cm, n-type silicon wafers which were 0.009 in. thick; but the data approximately apply to deposition of SiO, on thin films of aluminum. It is difficult to obtain accurate deposition rate data over aluminum films because of coarsening the aluminum surface during exposure to 300" to 400°C. The deposited SiO, film fol-

Jan 1, 1969

By George H. Cook

At first sight this subject seems to belong to pure theoretical geology, but examination will soon show that it has important practical and economic interest to the mining engineer. The conclusion that all the northern portions of our country, as well as of the eastern continent, have, in the later periods of geological history, been covered with a thick bed of ice, is now accepted by geologists. This bed of ice, except in its greater magnitude, was like the modern glaciers of the Alps, and other mountains which extend above the line of perpetual snow. The marks it has left upon the surface show that it was comparatively thin on its southern edge, but that its thickness was much greater a little further north, and that it was several thousand feet thick at its kenviest parts. This variation of its surface would give it a descending slope towards the south, and cause the mass of ice, like a semifluid substance, to move in that direction,

Jan 1, 1879

Hermann A. Keller was born in Philadelphia, Pa., Mar. 23; 1860. He received a preliminary education at the gymnasium of Darmstadt, in Germany, and subsequently entered the University of Pennsylvania, graduating in 1881. After serving for a few months as an assistant instructor in mining and metallurgy at the University, he went to Leadville, Colo., where he became, at first, assayer and chemist, and in due time (1886) superintendent of the Arkansas Valley smelting works. In 1888, he was appointed metallurgist of the Globe works at Denver; in 1889, superintendent of the Philadelphia works at Pueblo; and in 1891, superintendent of the Parrot works at Butte, Mont., where he remained until 1896, in which year he was employed to reconstruct the smelting plant of the Mountain mines at Keswick, Cal. In 1897, he opened an office as consulting engineer in San Francisco; and from this time on enjoyed a wide practice both as metallurgical and as mining engineer. In the former capacity, Mr. Keller had already distinguished himself by the invention of the Keller mechanical roasting furnace employed at the Parrot works in Butte and the Germania works near Salt Lake. He was a frequent contributor to the technical journals, and he collaborated in the preparation of the chapter oil "Bessemerizing" in Dr. Peters's work, "Modern American Copper-Smelting." It is a curious coincidence that these two friends and collaborators died at almost the same time, Keller in Arizona and Peters in Massachusetts on the 16th and 17th of February respectively. The latter years of Mr. Keller's life were largely given to the examination and development of mines in all parts of the world-Alaska, Chile, Germany, etc. He finally established his professional headquarters in New York City. His death was caused by an underground locomotive accident at Clifton, Arizona, on Feb. 16, 1917.

Jan 5, 1917

By P. S. Kotval

THE nominal composition of "hconel" alloy 718 is 53 pct Ni-19 pct Cr-19 pct Fe-3 pct Mo-5 pct Cb-0.8 pct Ti-0.6 pct A1-0.05 pct C. The nature of the fine strengthening phase in this alloy has been open to debate. iseelstein' has identified the strengthening phase in the matrix of "Inconel" alloy 718 as a colum-bium-rich fcc y' precipitate. Wagner and Hall2 have noted that the metastable y' precipitate overages to an orthorhombic Ni3Cb precipitate which manifests itself as an acicular phase. These authors thus clarify Kaufman and Palty's earlier suggestion3 that the strengthening phase is orthorhombic NisCb. Wagner and Hall's review also reports work by cometto4 which suggests that the fine strengthening phase is not fcc / but bct with a Ni3V type structure and based on the Ni3Cb composition. Kir man and warringtons have shown by analysis of electron diffraction patterns that the metastable strengthening phase in a 55 pct Ni-15 pct 0-25 pct Fe-5 pct Cb alloy is bct and based on the Ni3Cb composition. Raymond~ has provided electron diffraction evidence which indicates that "y'" in "Inconel" alloy 718 is bct in structure. This note presents unambiguous data on the structure of the strengthening phase in "Inconel" alloy 718* ihe samples of this alloy were provided by courtesy of the ASTM task group on phase identification in 'superalloys. after prolonged aging. The electron diffraction patterns presented show that strengthening phase is not y' but bct as was proposed by cometto,' supported by Raymond,~ and identified by Kirman and warringtons in a similar system. Fig. 1 shows a selected-area diffraction pattern taken from a thin foil of "Inconel" alloy 718. The sample had received a final aging treatment of 1118 hr at 1200°F to precipitate the strengthening phase in the matrix. Fig. 2 is a schematic representation of the features in the diffraction pattern. The matrix orientation is (0i2)~,, as is shown by the indexed zone in Fig. 3. Figs. 4, 5, and 6 illustrate that the pattern, Fig. 1, is composed of three bct zones, viz., (0i4), (2i0), and (i01), respectively. These three zones correspond, respectively, to the alignment of the c axis of the bct unit cell with the [001], [loo], and [OlO] directions of the fcc matrix and serve to illustrate the fully coherent relationship of the precipitate structure with the matrix. The streaking of certain reflections is also consistent with the above orientation relationship. The interpretation of the diffraction effects presented here shows the metastable strengthening precipitate in "Inconel" 718 alloy to be bct in structure and demonstrates that it is not an ordered fcc y' phase.

Jan 1, 1969

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968

By W. E. Bergman, P. G. Carpenter, H. B. Fisher

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication', a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949

By P. G. Carpenter, H. B. Fisher, W. E. Bergman

The conditions under which barium carbonate can be used to remove sulfates from drilling muds are limited The amount of sulfate remaining in solution in the system after treatment with barium carbonate is shown to be a function of the concentration of the carbonate and barium ions and the concentration of other electrolytes. Barium hydroxide may advantageously replace barium carbonate when the contamination is not entirely due to anhydrite (calcium in the system is then stoichiometrically less than sulfate) or when the carbonate concentration is high. The effect of substances such as quebracho, phosphates, and chromates, which form complexes or precipitates with barium, is discussed. INTRODUCTION As the complexity of the operations in drilling for oil has increased, more attention has of necessity been directed to the problems pertaining to the maintenance of good drilling mud properties. As a result, chemical treatment of muds has become an important factor in recent years. Some of these treatments have been designed to eliminate the deleterious effects of contaminants in aqueous mud systems by precipitation or other means. The most common of substances encountered during drilling include sodium chloride, cement, and calcium sulfate while various other contaminants: usually in small amounts, may be introduced from the water, clays, and other materials used in preparation of the mud. In certain cases, for example where continued salt-water flow is encountered or massive anhydrite is drilled, special muds may be used so that the physical properties of the mud will remain satisfactory for drilling. In other cases, it is desirable to remove the contaminants so that soluble electrolytes in the system are maintained at low values. For sulfate contamination, the conlmon practice in the field is to add barium carbonate to precipitate the sulfate as barium sulfate Ordinarily such a procedure gives satisfactory results. There have been important instances, however, where addition of barium carbonate was not effective in removal of soluble sulfates from drilling muds. and it is to these cases that the present paper is directed. While it is generally known that barium carbonate is not always effective in removing soluble sulfates from drilling muds, certain inconsistencies appear in the literature as to the limitations of its use, and little explanation for the limitations are given. Varnell and Kimbrel state that "the treatment (with barium carbonate for removal of sulfate) is simple and consists in maintaining a pH of 9 with caustic soda and quebracho." They caution that concentrations of quebracho greater than 1 lb./bbl. may inhibit the reaction. In another publication', a pH of 10.5 is considered "the maximum desirable," and the indication is that as much as 2.5 lb. quebracho per barrel may be present in the particular mud under discussion. Lancaster and Mitchell5 state that appreciable amounts of phosphates in the mud will inhibit the reaction with barium carbonate and that the phosphate treatment should be discontinued at least 24 hours before addition of the carbonate. Experimental work was initiated to ascertain the factors involved in using barium carbonate for the removal of sulfate contamination in drilling muds. While the experimental data herein reported are limited, they focus attention on the pertinent factors which must be considered for successful treatment. These factors are discussed from a practical and a theoretical view, the latter being supported by equilibrium data found in the literature. Further, it will be appreciated that the factors involved in this specific study will be closely analogous to those in certain of the other chemical treatments which involve a precipitation of the soluble contaminant. A thorough comprehension of these factors should result in a more fruitful application of this type of chemical reaction to the treatment of drilling muds. EXPERIMENTAL A. Reagents Two muds were used during this investigation. For one series of tests, bentonite suspensions were prepared by dilution of a stock suspension containing 8 per cent by weight of bentonite (Aquagel). For another series, a 6.4 per cent ben-tonitic mud weighted to 9.7 lb./gal. with barium sulfate (Mag-cobar) was used. Distilled water was used in all preparations. The quebracho (72% tannin extract) was obtained from the Thompson-Hayward Co. of Tulsa and contained 11.4 per cent moisture (105 C.). All other materials were reagent grade, and concentrations were corrected for water of crystallization, if any. All concentrations are expressed in pounds per barrel (42 gallons). B. Technique The systems — either mud or water — were contaminated with either sodium or calcium sulfate after treatment with the desired amounts of sodium hydroxide and quebracbo. For treatments with barium carbonate an approximately 3-fold excess (5 lb./bbl.) was used over that computed to be required to precipitate all the sulfate as barium sulfate. Barium hydroxide was used in concentrations of 2 lb./bbl. — about

Jan 1, 1949