Search Documents

By A. J. Miller, G. R. Brophy

The Grossmann principle1 for the calculation of hardenability of steel from composition is attractive because of its simplicity. It postulates that the hardenability of a steel for any particular grain size may be expressed in terms of an ideal critical diameter, which is the product of an ideal critical diameter for a "pure" iron-carbon base multiplied by a succession of factors for each element of composition contained, including the incidentals. It infers that the multiplying factor for a given quantity of an element is constant for all combinations of composition. Gross-mann has stated that in the great majority of cases the experimental values of hardenability are found to be well within 10 per cent of the calculated values. The validity of the scheme has been confirmed in principle by Crafts and Lamont2,3 and by Kramer et al.4 Their results differ from the original in the magnitude of the effect of some elements but, since they accepted the product concept and followed its direction, it is to be ex~ected that similar results would be obtained. Crafts and Lamont, in their second Paper, recognized that the factor relations for manganese and nickel were not continuously linear, but beyond certain critical amounts increase sharply. Austin, Van Note and Prater6 demonstrated nonlinear relations between hardenability and alloy contents. Their curves for chromium, silicon, manganese and nickel were all convex upward to show decreasing incremental effects. They concluded that Grossmann's factors under-evaluate the hardening effect of low percentage additions of these elements, and overevaluate the larger additions. More recently W. Stevens has found that the factor method fails when applied to complex steels containing two or three principal alloying elements other than carbon. Multiplying factors derived from his results bear a complex relation to composition and are not constant for a given amount of an element as the base composition varies. C. A. Liedholm7 found that, using either the Grossmann or the Crafts-Lamont multiplying factor values, not only were the relative hardenabilities of two heats of S.A.E. 6130 chromium-vanadium steel

Jan 1, 1947

R. M. Raymond, New York, N. Y.—The filling and drawing down of the overhead material was done at considerable depth, which is not the usual method in which it starts at the surface.. R. J. Mechin.— It is a little more than 1000 ft. at El Bordo. The vein above had been caved practically to the surface and some of the ore had been excavated, using underhand and overhand square-set methods. This was far enough away from the shaft to prevent any bad effects. When the sill floor was taken out, to insure the old cave material following down well, we put chutes in the square sets for several weeks until we were sure that the material from above was moving down; on each level above, several crosscuts were driven into the old fill by which we could see the material coming down and thus be sure it was following the first. We had to dynamite it very little because it was dry and dusty. The only trouble was that timber starting from the old square sets would get across the chute and hang up. R.. M. Raymond.—HOW many floors did you operate at once? R.. J. Mechin.—We would operate one floor through the whole length and prepare for the second. F. W. SperR, Houghton, Mich.—Could you have worked it in steps? R.. J. Mechin.—Yes; but working it all on one floor was much better for ventilation. The passage between steps would tend to become heavy and blocked and, as the passages from the mining floor down are usually filled with ore, there would be no way for the air to pass up. By means of doors and fans, air was driven to the extreme end of the orebody through the stope and up the other end; but it could have been worked in steps. F. W. SpeRR.—D the following-up material ever become so heavy that you could see weight on the caps before you had to take out the posts?

Jan 1, 1927

By Tibor Stefansky, John E. Dorn

MOTT and Nabarro1-5 were first to illustrate the importance of the flexibility of dislocations in accounting for the strengthening that metals undergo due to the presence of internal-strain centers. Such strain-centers might arise from a number of causes such as radiation damage, the presence of semicoherent and coherent precipitates and clusters, as well as individually dispersed interstitial and misfit substitutional solute atoms. Each strain-center induces positive and negative shear stress fields on the slip planes of the surrounding alloy matrix. In order to effect plastic deformation, therefore, the alloy must be subjected to sufficiently high applied shear stresses to push dislocations past all such internal stress fields. If dislocations were inflexible and moved as rigid lines, they would be equally pushed and pulled by internal stress fields. At this extreme the strengthening would be vanishingly small. Dislocations, however, are not rigid; they are flexible and extensible. They wiggle between positive and negative strain-centers, thus increasing their line energy at the expense of their interaction energy with strain-centers. cottrel16 and Friedel7,8 have independently presented lucid reviews of the significance of the Mott-Nabarro dislocation-flexibility concept to the strain-center strengthening of alloys. Their analyses however were only semi-quantitative. There is evidence in the recent literature of renewed interest in a more rigorous analysis of flexibility. Thus, Gleiter9 and Gerald" have shown that the calculated strain-energy interaction between a dislocation and the stress fields of coherent precipitates can be seriously in error if the flexibility of the dislocation is not taken into account. This report will be concerned with a more detailed analysis of the problem based on the following approximations: 1) Although many types of strain-centers exist, the following analysis will be limited to the case of solute-atom strain-centers in fcc substitutional alloys. 2) To facilitate the analysis by avoiding statistical considerations, the strain-Centers are assumed to be in regular arrays on the slip plane. Although the quantitative results are somewhat dependent on the type of array that is assumed, the qualitative trends are similar for various arrays that were studied. 3) An adjustment of the results from those for square arrays to those for the more realistic case of a random distribution of strain-centers is accomplished by adopting the interesting statistical theory first introduced by Kochs,11,12 elaborated on by Dorn, Guyot, and stefansky,13 and analyzed by Foreman and Makin14 in their computerized experiments. 4) For simplicity the dislocation lines are taken to wiggle about their edge orientation and no correction is applied to their line energy for deviations from edge configurations or for the elastic interaction between segments of the now curved dislocation. It will be shown that for extremely low concentrations of atomic strain-centers the strengthening increases with the square root of their concentration. For slightly higher concentrations the strengthening rate becomes less rapid. At a critical concentration a maximum strength is obtained and a decrease in the strengthening takes place as the concentration of solute atoms is further increased. These trends are a direct consequence of dislocation flexibility. They arise from changes in the amplitude of the waviness of the dislocation line at the yield stress with solute atom concentration. Despite the simplifying assumptions that were made, the results agree qualitatively with appropriate experimental data. I) STRESS FIELDS ON SLIP PLANES Internal stresses are introduced in a lattice whenever a host atom of radius ro is replaced by another that has a different atomic radius. According to the classical theory of linear elasticity,15 the stress field about a solute atom at the origin of a spherical coordinate system is given by arr=-4G€(?_0)3 ffflfl ="W =2G€{t) f°rr^ro(l+e) UJ where G is the shear modulus of elasticity and Y, = ro(l + E) is the radius in situ, of the substituted atom. As shown by ~shelb~,'~ this approximation assumes that the bulk modulus of elasticity of the substituted atom is identical with that of the host species. ~abarro'~ suggested that the strain E can be deduced

Jan 1, 1970

By Miroslaw Hajdasinski

Estimation of the economic effectiveness of industrial development projects including mining ones is generally made on the basis of the discrete model of the value changes in time, although the character of these changes is similar to the continuous model. In this paper an attempt has been undertaken to investigate the problem of the value equivalence of both models exemplified by a construction of an underground coal mine. An effort has been made to determine the errors which for different estimation criteria appear in result of the application of the discrete model. Theoretical considerations have been supplemented with practical conclusions.

Jan 1, 1977

By James Douglas

Once—and fortunately only once—before this occasion, was it my sad duty to express the loss we had sustained in the death of an eminent member. Dr. T. Sterry Hunt* was a student of chemistry who, by his investigations into the properties of the elementary bodies, had assisted emineiltly in the progress of the technical arts, and, more than any American of his generation, had helped to lay the foundations of chemical geology. William Earl Dodge, whose death we deplore to-day, occupied a rank not les~ importaiit in the army of industrial workers

Jan 1, 1904

By M. Albertson

At Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 m.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 m.), the width at the lower lobe was about 1000 ft., and the width at the narrows probably 400 to 500 ft. The original depth of water varied from 20 to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the lake. About 1,500,000 tons of mill tailings, composed of sands and slimes, were discharged into the lake's waters previous to 1915. Most of this material

Jan 1, 1921

By Robert E. Green, P. W. Kingman

Application of a constant geometry compression test to single crystals of aluminum of selected diameters from 1/4 to 1/64 in. showed the presence of a diameter-dependmt size effect. The most pronounced effects were found in those crystals oriented for single slip, while for specimens possessing orientations in the comers of the standard stereographic triangle virtually no size effect was exhibited. The yield stress of the crystals oriented for single slip was found to increase with decrease in specimen diameter, while the strain-hardening rate was found to be lower for the smaller specimens. The experimental results are in general agreement with those of other investigators obtained from lensile tests on copper and aluminum crystals. THE earliest systematic investigation of a possible size effect on the plasticity of metals was that of no,' who in 1926 performed tensile tests on cylindrical aluminum single crystals with diameters of 3 to 8 mm. Ono concluded that the gross stress-strain curve did not show a diameter dependence, but that the resistance to slip for strains of 0.1 pet and less appeared higher for 3-mm-diam crystals than for larger sizes. Later studies of aluminum by Maddin et al2 tentatively concluded that a size effect exists, but the conclusions were again open to question because of inconsistencies in the experimental data. Wu and Smoluchowski3 had previously shown that the slip system activated in a single-crystal sheet specimen of aluminum is a function of the specimen cross section in the slip direction, but no stress-strain data were obtained. Subsequently Fleischer and Chalmers4 studied the effect of the length of the slip direction of the primary-slip system on the stress-strain curve by testing aluminum crystals with geometrically dissimilar cross sections. In the course of this investigation a size effect was indicated in rather large crystals; however, the number of these tests was small. Other investigators have indicated that a size effect in aluminum is appreciable only for diameters of 0.5 mm or less.5, 6 Size-effect studies have also been carried out on copper crystals, the most detailed being that of Suzuki et a1.7 who performed tensile tests on specimens of many diameters ranging from 2 to 0.12 mm. Suzuki found a strong size dependence in the easy-glide region, both the extent of the easy glide and the hardening rate in easy glide were size-dependent, and the size effect was found to be orientation-dependent. Suzuki's results are in agreement with the less extensive observations of Pater-sonB and those of Garstone et al.9 A size effect was found by Rebstock using tubular copper crystals.'0 Size effects have also been noted in a brass,6, 11 in cadmium,12'19 and in hexagonal crystals.14 All the previously cited works have been entirely concerned with the variation of specimen cross section. The effects of specimen length and the change of specimen geometry which results from using progressively thinner specimens while maintaining the same specimen length have been largely ignored. A theoretical discussion of the effects of specimen length and geometry has been given by Hauser and Jackson,15 who predict a grip effect on easy glide as a function of specimen geometry provided that the specimen dimensions are large compared with the spacing between the slip bands, and by Fleischer and Chalmers,18 whose analysis of grip effects resulting from lattice rotation predicts an increase in easy glide with an increase in specimen length. A study of size and geometry effects in aluminum crystals by Kitajima and shimba17 indicated increasing amounts of easy glide in specimens of increasing length and identical cross section, and nearly identical stress-strain curves for specimens of different sizes having constant length-to-diameter ratios. Since the present study is primarily concerned with diameter dependence, the following factors were taken into account: specimen material, specimen geometry, testing method, range of sizes to be tested, and possible influence of surface and volume effects. Aluminum was chosen because of the present lack of conclusive results and the seeming possibility of size effects at relatively large diameters, the

Jan 1, 1964

By N. M. Levine

WHETHER the United States and its allies can W meet the challenge of a war brought by the Communists will depend largely on who wins the battle of steel production. At the present stage of the world situation, the United States and the other members of the Western family of nations have the lead on iron curtain countries. But we have no sure way of knowing what is happening at Magnetogorsk and other Russian iron and steel producing centers. We must also face the possibility that we may have to meet the challenge alone. The fortunes of war and world politics can strip us of friends and co-fighters quickly. The destruction of Hiroshima and Nagasaki are indicative of what the world can expect if war-madness ever grasps the earth again. Our domestic supply of high grade open-pit and underground iron ore is dwindling because of the drain of three wars and higher than ever civilian consumption. The production of iron ore and its eventual use in blast furnaces are the critical problems of an armed democracy today. The world crisis has led to efforts towards beneficiation for increasing ore supplies. The huge reserves represented by the magnetic taconites at the eastern end of the Mesabi, once in production, should provide us with a substantial portion of our native ore for many years. The estimated 10 to 20 million tons of concentrates annually can be increased in an emergency. If we had a certainty of peace for the next 50 to 100 years, the situation would be a stable, hopeful one, aided by importations of high grade ore from sources such as Canada and Venezuela. The hard truth is that we have little surety of peace tomorrow morning. Let us assume 'the U. S. could build sufficient processing plants for increasing production of magnetic taconites under the pressure of national emergency. We must also recognize the power of atomic warfare to contaminate an area as large as the Eastern Mesabi. Thus, it becomes imperative to seek some means of protecting our ability to produce the steel we may one day need to survive. The nonmagnetic taconites, completely dwarfing the magnetic taconites areawise as well as tonnage-wise, might provide us with this insurance. Present indications are that they will be considerably more expensive to treat, but in a desperate situation we might be very grateful for ores yielding 40 to 50 pct Fe recoveries at grades of 53 to 58 pct Fe carrying low phosphorus. The University of Wisconsin, because of the difficult iron ore situation in the state, has been working on the nonmagnetic taconite problem for the past three years in the hope of making a contribution toward its eventual solution. In Wisconsin, the Western Gogebic Range has been the state's most effective iron producing area. Today however, only two mines are in operation, both underground and approaching depths of more than 3000 ft. The range, however, does have a large supply of nonmagnetic taconites and presents a promising field for study. While the Gogebic offers one large source of nonmagnetic taconites, Michigan and Minnesota have even greater supplies of such material. Alabama, the northeastern states and the West all have low grade iron ore sources which might be utilized under extreme conditions. The Gogebic Range located in northeastern Wisconsin and northwestern Michigan has a total length of about 70 miles, about 45 of which are in Wisconsin. The iron formation averages 500 to 600 ft in width, dips 70' to the north and strikes at approximately N 63° E. The formation is sedimentary and consists of six distinct members characterized by alternating divisions of ferruginous chert and ferruginous slate. The footwall is generally quartzitic and the hanging wall of a sideritic slatey character. The iron minerals are mainly hematites with some magnetites, goethites, limonites and small amounts of siderite. In the area studied, very small amounts of iron silicates were observed. The magnetites occurred mostly in the Anvil-Pabst and Pence members, mixed with hematites and representing roughly about 10 to 20 pct of the total iron in the formation, thereby characterizing it as nonmagnetic. The gangue is of various forms of silica such as chert, opal and flint. Complete liberation of iron and gangue minerals is rare. There is always some iron present in the chert ranging from jasper-like solutions to fairly coarse iron oxide specks. Likewise, one always finds finely dispersed silica within the iron minerals. In late 1943 the Bureau of Mines carried out a trenching and sampling program in the two mile stretch between Iron Belt and Pence in Iron County, Wis. Preliminary work was based on samples from one of the four trenches cut by the Bureau of Mines. More detailed work following the preliminary analysis was then undertaken on samples composited from all the trenches, thereby giving a wider and more representative coverage of the area. A study of the

Jan 1, 1952

By Willard S. Morse

The ores of the district are treated at this mill by the lixiviation process, consisting of drying, crushing, chloridizing-roasting and lixiviation by hyposulphite and Russell solutions. Gas is used as fuel for both drying and roasting, The gas-plant consists of two- Taylor revolving-bottom gas-producers, one 6 feet in diameter for the ore-dryers, the other 7 feet in diameter for the Stetefeldt furnace. The producers were made by Messrs. R. D. Wood & Co., Philadelphia, who also furnished the

Jan 1, 1893

By W. McA. Johnson

The work of J. E. Johnson, Jr., on the effect of small amounts of oxygen in cast iron in increasing its strength and resistance to shock, is of interest from the technical and scientific standpoints. The following exposition of the theory carries Mr. Johnson's explanation further and, in my opinion, will disclose certain related phenomena and perhaps shed further light on the subject. Some facts, so novel in character as to excite incredulity, have been accepted finally by many metallurgical authorities. One of these is that oxygen to the amount of 0.060 per cent. in cast iron gives it a breaking strength of 3,500 Ib. per square inch, compared with a breaking strength of 2,500 lb. per square inch in cast iron of the same composition with respect to elements other than oxygen, but having only 0.010 per cent, oxygen. The "oxygenated" cast iron, even if made in a coke furnace, has properties equivalent to the best charcoal pig iron. Mr. Johnson has also established the fact that the variations in combined carbon cannot account for the results. By microphotographic evidence he has shown that in oxygenated cast iron the graphite particles are dense and spherical, while in well-deoxidized cast iron the graphite particles are flaky and leaf-like. It is just a matter of common sense that iron of the latter structure is much weaker than the former. The analytical and microscopical work has been done with care and there is no doubt in my mind about the accuracy of the experimental results. In this paper then, we shall consider it as accepted that small amounts (0.060 per cent.) of oxygen increase the strength of cast iron by producing a structure in which the round and solid particles of graphite are surrounded firmly by a principal matrix of ferrite. The purpose of this paper is to show that the reason why the graphite particles are round is founded on the fact that the particles of any precipitate are made denser and harder by the presence of a reagent having a solvent action on the precipitate. This can be stated as a law, although I have never seen it so given in any textbook. Let us then, for purposes of illustration, give a concrete example and develop the theory of such mechanical and chemical actions as occur: It is well known that, by a soluble sulphate, a barium salt in solution is precipitated in a dense and easily filtered body when the solution is

Jan 1, 1916

By George C. Stone

The stack gases from regenerative furnaces lare very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300" C. (572" F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450". The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 1, 1914

By R. V. Wheeler, F. V. Tideswell

Coal being essentially a complex conglomerate of plant remains that have undergone decay and interaction in varying degree, it is understandable that attack on the problem of its chemical constitution by normal chemical methods should have been attended by but slight success. The obvious method of fractionation by means of selective solvents has yielded a few results of some value. Thus it is known that from many, if not all, bituminous coals organic solvents extract small percentages of oxygenated compounds, which are generally assumed to have been derived from the original plant resins, though a more probable source would appear to be the glycerides and waxes of the plants. Organic solvents also extract small proportions of hydrocarbons, the origin of which is doubtfill. Of more importance is the action of such pseudo solvents as pyridine, which, in addition to their specific solvent action, have the power of resolving and simplifying a portion of the coal substance in a manner analogous to that by which water can disperse a hydrogel. Early work with pyridine indicated that coals are composed of two main classes of compounds: the one soluble in organic solvents, the other capable of being partly dispersed in pyridine. Recent work has shown that the dispersion is colloidal in character and that it may be accomplished by the use of solvents less active than pyridine, such as benzene or chloroform, provided that the temperature of extraction is raised or the coal has been suitably preheated. The action of reagents on coal has proved of little value in the past, but some insight into the constitution of coal has been given by regulated destructive distillation. Thus, it has been shown that coals behave on distillation as though composed of two main classes of compounds: the one readily decomposable at moderate temperatures (yielding mainly the paraffins), the other undergoing a preliminary early decomposition (with evolution of oxides of carbon and water) and yielding a residue that at higher temperatures breaks down, yielding much hydrogen.

Jan 1, 1925

By H. M. Howe, E. C. Groesbeck

That the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First, each particle of any composite liquid, whether it be an aqueous solution or a molten metal, in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the existing temperature, and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already solidified; A, Fig. 1. The other part is fusible at the existing temperature and hence remains molten. In the case of carbon steel, the part of each drop which actually solidifies is poorer in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying half-drop enriches the other half-drop in carbon, and thus makes it unfreezable at the existing tern- By this mechanism there arises during solidification a "littoral" or shore layer of liquid B, Fig. 1, bathing the already solidified walls, and more fusible than either those walls or the great remaining central mass of liquid or " deep sea " C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal could get past this littoral layer and come into contact with the solid walls, it would in turn solidify, and like its predecessors would split up in solidifying into a less fusible half-drop which would attach itself to those . walls and a more fusible one which would remain molten. Thus we see

Jan 1, 1920

By R. Costantini

A. Brebner (Chairman, Dept. of Civil Engineering, Queen's University, Kingston, Ont., Canada) — Under the heading of friction losses, the author, in Eq. 10, gives the relationship

Jan 1, 1962

By R. G. Davies, R. H. Richman

Several techniques, X-ray diffraction, transmission electron microscopy, conventional, metallography, and mechanical property measurements are combined to investigate decomposition in the suPersaturated solid solution Fe-27 at. pct Be. The following sequence of structures for aging temperatures below 400°C is established: massive short-range order, pseudo-FeBe (L2o) order, Fe3Be (DU3) order, sinusoidal modulation of composition, general or continuous precipitation, and discontinuous or cellular precipitation. In addition to this sequence itself, several features of the individual stages are noteworthy; for example, when coherent modulations occur, their development is parallel to (100) everywhere in the specimen apparently without incubation, and both the wavelength and the composition amplitude of the modulations increase with aging time. Two types of discontinuous reaction are observed, depending upon the aging temperature. At low temperatures (<550°C) the boundary-nucleated variety of discontinuous precipitate predominates; but at higher temperatures (>600°C) the crystallographic variety occurs instead. Hardness and flow-stress measurements clearly reflect the quoted structure sequence. Some qualitative aspects of the structure changes and of the relationship between mechanical properties and structure are discussed. BERYLLIUM in solid solution markedly strengthens iron.&apos;" A recent study demonstrated that not only were supersaturated single crystals of Fe-27 at. pct Be very strong, but they deformed primarily by mechanical twinning.3 Such behavior, coupled with the decrease in solid solubility of beryllium in a Fe from about 33 at. pct at 1165°C to about 10 at. pct at 500°C4 as shown in Fig. 1, leads naturally to questions about property changes with aging in this system. In 1929 roll,1 and later Seljesater and Rogers,5 reported that useful increases in strength could be obtained by aging quenched Fe-Be alloys, but it was not until quite recently that any of the details of precipitation in these alloys were studied. Richman6 observed that both an Fe3Be superlattice (with a DO3 crystal structure the same as Fe3A1, illustrated in Fig. 2) and a modulated structure preceded the appearance of a discrete second phase in the 20 at. pct Be composition. Here, a modulated structure refers to a periodic composition fluctuation within one crystal, while its lattice remains coherent. Subsequent work on a Fe-Be alloys by Heubner7 and von Heimendahl and Heubner8 confirmed the existence of the modulated structure, although only an FeBe (L20) ordered structure was detected (also shown in Fig. 2). Both Rich-man and Heubner corroborated the large increases in hardness during aging reported earlier, but other mechanical properties were not examined. Since modulated systems are encountered relatively infrequently, the influence of coherent modulation upon mechanical properties is not well-known. With the accumulation of information about age-hardening systems, it has become clear that many precipitation reactions cannot always be described by the concept of heterogeneous nucleation at some lattice discontinuity followed by diffusional growth. Rather, complex sequences involving prior "preparation" of the matrix are quite common; that is, a transition structure occurs in the parent phase, instead of in some "nucleus" form. Delineation of such subtle sequences appears to be a worthwhile step toward the understanding of solid-state precipitation. Since not many structural progressions of comparable nature have been reported, the objectives of the present survey are to identify and elucidate the various

Jan 1, 1967

By Robert E. Ogilvie, Zvonimir Ban

Oxidation experiments were conducted above 600°C to investigate the oxidation products formed on the surface of MoSi2. Results are presented which indicate that minor iron impurities play a key role in the oxidation behavior of MoSi2 above 600 °C. Based on considerations of the crystal chemistry of the oxidation products, MoSi2 with rhenium and iron additions was found to be resistant to oxidation in the pesting temperature range. AS early as 1914, Honigschmidtl observed that some silicides of molybdenum exhibited high resistance to oxidation at elevated temperatures. This fact did not arouse much interest until 1950, when Kieffer and cerwenka2 examined this property in more detail. They found that Mo-Si alloys with approximately 70 pct Mo (by weight) could be heated to 1600°C in an oxidizing atmosphere without any significant damage. The surface was found to be protected by the formation of an extremely thin silica glass layer which had no tendency to spa11 during subsequent thermal cycling. In 1955, Fitzer3 discovered that even solid bodies made of MoSi2 completely oxidized within a relatively short time when exposed to the air in the temperature range from 300° to 600°C. To describe this phenomenon he proposed the name "molybdenum disilicide &apos;pest&apos; ", clearly analogous to the previously observed "tin plague" ("tin pest") which, however, arises as the result of a phase transformation. Studies performed by Fitzer and, in particular, one published recently by Berkowitz, Blackburn, and Fel-ten,&apos; comprise the most extensive research to date on the pest phenomenon in MoSi2, as far as the fundamen- tal mechanism of the process is concerned. The first of these studies revealed the existence of a crystalline phase which appeared at the surface at 750°C and dissolved in the glassy silica layer at 1150°C. The logical assumption was that this phase was some reaction product of MOO3 and SiO2. The formation of a reaction product of this type seemed probable since it had been mentioned by Glemser and Lutz6 in a paper describing their studies of molybdenum oxides; however, this assumption was later disproved.8 It is our belief that information concerning the exact nature of this crystalline phase may be important for a better understanding of both pesting and the protection mechanism. Therefore, since the only available general description of the pest phenomenon was that of Fitzer, it was decided to reproduce his experiments. These experiments established that, in addition to the "pest" and "nonpest" temperature range, an intermediate region exists between 600" and approximately 650°C. This region is characterized by the appearance of a variable amount of yellow to orange colored crystals. The electron-beam microanalyzer was used to qualitatively determine their composition. Iron and molybdenum were found to be major constituents. This result can be explained based on the following facts: 1) iron, according to literature data,* is the most common impurity in molybdenum powder, and its content can be as high as 0.25 pct; 2) technical silicon powder usually contains iron; 3) steel ball mills are often used for the crushing and grinding of MoSi2. In order to clarify the exact role of iron, it was deliberately added to a stoichiometric mixture of molybdenum and silicon. The observed results corroborated the previous experiment, proving that iron (probably as some silicide phase) concentrates along the grain boundaries. I) EXPERIMENTAL PROCEDURE A) Oxidation of MoSi2 with Iron Additions. 1) Specimen Preparation. Specimens were prepared by both

Jan 1, 1967

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.&apos;s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.&apos;s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By George Stone

THE stack gases from regenerative furnaces are very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300° C. (572° F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450°. The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the .boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 10, 1913

By R. M. Jorda

The mechanism of parafin deposition and prevention has been studied in the laboratory using an apparatus which provides a quantitative means of studying parafin deposition on metal and plastic surfaces. The amount, hardness, adhesion, per cent wax and mean molecular weight of parafin deposits appear to be governed by surface roughness alone, all other conditions being constant. Tests of various plastic coatings indicate that most smooth, nonparafinic plastics are capable of reducing parafin deposits in oil wells, but flexible, highly polar, nonparafinic plastics are more suitable for providing long term resistance to parafin deposition in oil wells if the flow stream contains abrasive materials. INTRODUCTION The problem of paraffin deposition is one of long standing in the oil industry.&apos; Crude oils often contain paraffins which precipitate and adhere to the liner, tubing, sucker rods and surface equipment as the temperature of the producing stream decreases in the normal course of flowing, gas lifting or pumping. Heavy paraffin deposits are undesirable because they reduce the effective size of the flow conduits and restrict the production rate from the well. Where severe paraffin deposition occurs, removal of the deposits by mechanical, thermal or other means is required, resulting in costly down time and increased operating costs. The troublesome paraffins are normal hydrocarbons ranging from approximately C15H38 to C38H78 mixed with small amounts of branched paraffins, monocyclic paraffins, polycyclic paraffins and aromatics.&apos; The amount of paraffins found in crude oils varies from less than 1 to more than 30 per cent. Many publications are available which deal with this problem, and perhaps the most significant findings in recent literature are contained in a publication by Hunt3 ho developed the "cold spot tester", a really useful means of investigating paraffin deposition. Hunt&apos;s observations led to many generalized conclusions concerning the effect of surface roughness on paraffin deposits. He ascertained that there was an observable qualitative correlation between the severity of paraffin deposition and the roughness of the surfaces which he tested (cold rolled steel, stainless steel and several plastics). Because of the number of meaningful observations made by Hunt, his cold spot tester was modified somewhat and extensive tests were per- formed to study the quantitative relationship between surface roughness and the physical and chemical nature of paraffin deposits. LABORATORY TEST PROCEDURES The cold spot test apparatus consists of a flat circular plate mounted on a curved tube and positioned in a vessel containing a wax-oil solution (Fig. 1). The apparatus is arranged so that the temperature of the central portion of the circular plate can be varied by means of a circulating liquid stream; the test equipment includes provisions for maintaining a constant wax-oil solution temperature and stirring speed. In the paraffin deposition studies, the modified cold spot tester was used as follows. The cold spot probe consisted of a flat circular plat 2 in. in diameter and 1/8-in. thick positioned in the wax-oil solution kept at constant temperature. As in Hunt&apos;s earlier experiments," a cold liquid was circulated through a tube connected to the circular plate so that the liquid impinged on one side of the plate cooling the plate from the center outward, causing paraffin to deposit on the side of the plate exposed to the wax-oil solution.

Jan 1, 1967