Search Documents

[ ]

Jan 1, 1938

By Peter K. Strangway

During 1973, a 20,000 net ton (18 100 metric ton) formcoke test was carried out at Inland's 26.5-foot (8.08-meter) hearth diameter on NO. 5 Blast Furnace. The formcoke briquettes were produced from Elko1 coal by FMC at their pilot plant in Kemmerer, Wyoming. The briquettes were shipped to Inland in open railroad cars and most of them were placed in an outside storage field until a sufficient amount was available for the actual blast furnace test. The test consisted of three phases: an initial four-week base period; the actual 33-day formcoke test period; and a final three-week post-test base period. During the formcoke test period, the regular coke skip loads were gradually replaced with skips of formcoke until, after a three-week period, the replacement ratio reached 80%. The furnace operated smoothly and quality hot metal was produced. The burden remained permeable and it was possible to maintain wind rates 9 of over 100,000 scfm (47 Nm3/s) without significant blast pressure increases. Dusting from the formcoke was not a problem either in the stockhouse or in the top gas. The formcoke briquettes maintained their original shape and density as they descended through the furnace. When the 80 percent replacement level had been reached, the inwall temperatures became higher than normal (about 2000 ºF (1090 ºC)) and followed an unusual steady pattern. In addition, the top gas temperature became higher than normal, and the hot metal analyses and temperatures began to fluctuate unacceptably. In general, it is felt that the high inwall temperatures were a result of channeling of the hot furnace gases along the stack walls. This channeling appears to have been promoted by a change in distribution of the burden in the top of the furnace which, undoubtedly, was caused by the increased increments of formcoke. Since it was felt to be unsafe to operate the furnace for an extended period of time with the inwall temperatures at the high level, a decision was made to remove the formcoke from the furnace. When this was done, the inwall temperatures returned to normal. Once the inwall temperatures had returned to normal, the remaining 3,800 net tons (3450 metric tons) of formcoke were used in the furnace at a nominal 40% replacement level for five continuous days. The furnace operated smoothly during this period, and the results were representative of satisfactory furnace operation with partial replacement of regular coke with formcoke. The test was successful in proving that formcoke can replace up to about 50% of the regular coke in a large furnace operating at high wind rates. However, additional work will be required to develop acceptable charging practices for using higher levels of formcoke replacement.

Jan 1, 1977

Secretary's Note.—M. Beutter's introductory remarks, being simply a resume of Prof. Hone's paper, with a disclaimer of the intention to criticise it, have been omitted, and the remainder of this contribution lias been somewhat condensed, without omitting any essential statements. M. Beutter, St. Etienne, France* (communication to the Secretary†):—Professor Home observes in $ 47 of his paper that the fluid-compression of steel diminishes piping by forcing the liquid and viscous metal, while the pipe is forming, or after it has formed, into the space so produced, and proceeds to study the different systems of compression, alluding to the four principal ones: Whitworth, Illingmorth, Williams, and Harmet. Having now for many years had in use the last-named process, that of M. Henri Harmet, I shall attempt to explain the difference between it and the three other processes named. The Harmet process does not diminish or close the pipe after it has formed, but prevents it from forming; and I may add that it is the only one of the four which produces this result. It is true that the Whitworth process diminishes the interior hollow by localizing it around the central axis of the ingot, which is afterwards removed by trepanning the hollow forg-ings for which this process has been, I believe, always exclusively used. The Illingworth and Williams processes, which, in my opinion, are applicable only to small ingots, of necessity allow the pipe to form, or (to use the expression of Professor Howe) they allow the surface of the lake of liquid steel to sink into the interior of the ingot, since they involve waiting a certain time before compression, so that (in the case of the Williams process) the ingot-mold can be opened without danger, or (in the case of the Illingworth process) so as to avoid the risk that the steel may enter the grooves produced by the removal of the distance-bars. During the time required for

Jan 1, 1908

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By F. H. Buttner, E. R. Funk, H. Udin

A. P. Greenough (University College, swansea, Great Britain)—I have recently made some experiments on the deformation of silver wire at high temperature in an atmosphere of oxygen-free nitrogen. The observa-tions which 1 made confirm the main conclusion of this paper, that the most satisfactory mechanism so far suggested to explain the deformation which takes place

Jan 1, 1953

By S. Frederick Ravitz

JUDGING from the inquiries that are constantly being received by the Utah Engineering Experiment Station as to the "Why," so to speak, of the flotation process of concentrating minerals, it occurred to me that perhaps a brief statement of the more important theories might interest those who have not followed the technical literature. Like many other industrial processes, flotation has hitherto been developed on an almost purely empirical basis, with relatively little practical contribution from the fundamental chemistry and physics on which the phenomena are based. In fact, its development by the trial - and - error method has been perfected to such a high state that it is becoming generally thought that further important advances can be brought about only by a thorough understanding of the actual mechanism of the process. Natur¬ally, such a complicated process has brought forth numerous theories, most of which have failed to withstand the test of time. It is significant that no theory has yet been advanced which is universally accepted.

Jan 1, 1933

By Keith Sutherland

AEROFLOAT 25 is a complex mixture of free cresylic acid with aryl substituted dithiophosphoric acids, sulphides, disulphides, etc. Its complete composition has not been published by the makers or patentees. It is prepared1 by the reaction between phosphorus pentasulphide and carefully selected cresylic acid. We have been informed that this acid contains no phenol and very little cresol, and that it is rich in the higher alkyl phenols, particularly the xylenols. The reaction between a phenol ROH and phosphorus pentasulphide may produce compounds of the following type:2 (i) RO S P Diaryldithiophosphoric acids RO SH (ii) R-SH Thiophenolic compounds (iii) R-S-R Diaryl sulphides (iv) R-S-S-R Diaryl disulphides (v) Substituted thianthren compounds Except for the simplest type, the thiophenols (ii), the boiling points of these compounds lie above 300° C. The amounts of the thianthren compounds formed from the five xylenols (if all these are present) will vary according to the position of the substituents. In an attempt to ascertain something of the nature of the reagent, fractional distillation under atmospheric pressure was undertaken. At the outset, hydrogen sulphide was freely evolved, and-particularly below 200° C.-the fractions had the strong odor characteristic of the

Jan 1, 1939

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

[ ]

Jan 1, 1946

By Chester A. Fulton

SUPPLYING as it does a necessity for healthy animal and vegetable phosphate production is a most important industry. We human beings also are animal as this war so surely proves. Unlike many other elements no substitnite is available for phosphorus or its compounds. Marvelous as are modern plastics none can lake the place of phosphorus in making hone structures. As meassured in these times the phosphate industry is not a large industry. Output of phosphate rock, the original source of our agricultural and ,chemical phophates amounts to only some twelve million long tons per annum in the entire world. Phosphates are compounds of phosphorus, which is always found in nature combined with other elements. It never occurs in nature as such. The first choice of the element phosphorus is tie itself strongly to oxygen and then to water moisture - thus becomeing phosphlic acid. This phosphoric acid in turn hunts around for a base such as lime for instance and together they make phosphate of lime.

Jan 1, 1944

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has averaged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by persons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore transportation, persons falling, explosives, and asphyxiation. Accident Prevention The improvement of the safety record was obtained by a combination of many factors. In surveying the results at Andes for the past twelve years, it is possible to select some features of the present operation which have contributed to the accident record. The most important of these are: (1) good staff planning, (2) good equipment, (3) an alert safety organization, and (4) education and selection of the workmen. GOOD STAFF PLANNING As a result of good staff planning, the mine has good working conditions, namely, good ventilation, moderate temperatures and humidity, and good lighting. These factors not only reduce accidents but also improve efficiency. In haulage work, accidents have been reduced by having traffic move in a forward direction only. The latter makes possible a one-man train crew. Trains are centrally dispatched from loading drifts which are interconnected by signal lights, so that when a train in a lateral drift is given permission to move into a main line drift, a red light signals in all other lateral drifts in that area. Good track is maintained, and safety niches are required at all switch throws. Since safety niches were provided there have been no fatal or serious accidents at such points. All main line haulage drifts are illuminated by electric lights. Haulage drifts are kept clean. Adequate clearance has been provided between cars and between cars and the sides of the haulage drifts. The 4 1/2 ton Cranby type cars are equipped with roller bearings, and the 10 ton loconlotives with trolley shoes instead of wheels. These two features are responsible for improved ore haulage conditions and contribute to greater efficiency and safety.

Jan 1, 1950

By A. Perry Thompson

I. GENERAL DISTRIBUTIONS APPEARANCE, AND RELATIONS MINING in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,1 it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 4, 1915

By Thomas T. Read

Jan 1, 1913

By Raymond E. Birch, Oscar M. Wicken

THE mineral magnesite, formerly the source of nearly all magnesia, now shares this role with brucite, dolomite, and the world's natural and artificial brines. The mineral magnesite is the normal carbonate of magnesium, MgCO3, composed when pure of 47.6 pct MgO and 52.4 pct CO2. It is one of the calcite (CaCO3) group of rhombohedra1 car- bonates, which also includes dolomite, CaCO3.MgCO3, and siderite, FeCO3. Magnesite does not form an isomorphous series with calcite or dolomite; consequently, these lime-bearing carbonates commonly present in magnesite deposits are there only as mechanical mixtures. Magnesite and iron carbonates form a continuous isomorphous series and therefore are inseparable mechanically. The variety of magnesite known as breunnerite is an isomorphous mixture of iron and magnesium carbonates. Magnesite may be either crystalline or amorphous (cryptocrystalline). The former, which includes breunnerite, is often termed spathic magnesite. Crystalline magnesite varies from finely to coarsely crystal- line in texture and has a hardness of 3.5 to 4. The color is white, yellowish, blue-gray to drab, red, pink, black, or mottled. It is seldom found pure but usually contains variable amounts of iron, lime, silica, and sometimes manganese. The color cannot be used as an index of purity. The cryptocrystalline variety is perhaps the more common type but the crystalline variety usually occurs in larger deposits. The amorphous type is fine grained and compact, showing no cleavage. It is usually snow white but sometimes is light to pale orange yellow or buff, owing to impurities. The fracture is conchoidal to uneven and the hardness 3.5 to 5. Silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. The lime and iron contents are usually low. In general, amorphous magnesite is somewhat purer than the crystalline variety. The specific gravity of cryptocrystalline magnesite is 2.90 to 3.00. Pure crystalline magnesite has shown a specific gravity of 3.02 but iron

Jan 1, 1949

By Wayne Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions, Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illus-trate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938

By J. J. Friel, E. S. Erickson

Dolomite-fluxed pellets of various compositions were made from magnetite concentrate, hematite concentrate and a concentrate containing a natural mixture of both. Physical properties and reduction test results were used to ascertain proper compositions and firing temperatures. These pellets were subjected to physical tests and to reduction tests. Petrographic and electron microprobe examinations were made to evaluate the effect of composition and fining on the phase assemblage. We interpreted our test results in terms of chemistry and microstructure and related these to properties. This approach enabled w to determine the composition best suited to each of the three concentrates. Compared with acid pellets, dolomite- fluxed pellets of the optimum compositions had similar physical properties but swelled less, softened at a higher temperature, and reduced faster and more completely.

Jan 1, 1983

By Ottey M. Bishop, William G. Peryam, Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rocksurfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to [P]8.oo per ton, and from the property to San Fernando the rate is [P]16.00 per ton. The company pays the road toll, [P] 1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

William Kent, New York, N. Y.:—The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is an admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly gives the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer—Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, Sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer—Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric transmission, electric smelting. Work of the Chemist and Metallurgist—Explosives, chlorina-tion, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist—Economic geology. Work of the Mining Engineer—Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing those things he was trained to do as a specialist, but in making use of the knowledge of geologists, chemists, and electrical and

Jan 1, 1910

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944