Search Documents

By L. J. Ebert, G. Sachs, W. F. Brown

Isothermal transformation, or "aus-tempering," of a carbon-containing aus-tenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.' Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4,5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.637 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels,8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140) The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. .Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1949

By G. Sachs, L. J. Ebert, W. F. Brown

Isothermal transformation, or "aus-tempering," of a carbon-containing aus-tenite at elevated temperatures yields so-called "intermediate products." Their structure and properties are, for a given hardness, rather different from those of "tempered martensite" obtained on conventional quenching and tempering.' Several investigators2,3 have found that for high carbon and slightly alloyed steels the intermediate products formed at temperatures close to that of the martensite reaction possess strength properties superior to those of tempered martensite. The structure of these low temperature, intermediate products is generally acicular (bainite) but clearly different from that of martensite. However, at higher austempering temperatures, between 1000 and 1300°F (540 and 700°C) carbon steels were found to exhibit a rather low ductility.4,5 Thus notch bar tensile tests showed the ratio between notch strength and regular tensile strength to decrease with increasing austempering temperature. For ductilities below a few percent this notch strength ratio is a measure of ductility, according to investigations on low alloy steels.637 Furthermore the presence of intermediate products formed unintentionally on quenching was considered as responsible for the low ductility and impact energy of some heat treated steels,8 These intermediate products could result from partial transformation at the so-called "nose-temperature" where the rate of the transformation is a maximum. Tempering improved such mixtures of martensite and intermediate products, their properties approaching those of tempered martensite of equal hardness. The following investigation constitutes an attempt to determine certain strength properties of a partially austempered and subsequently quenched low alloy steel, namely, a chromium steel (SAE 5140) The structures formed by such a treatment should consist of a mixture of intermediate products formed on austempering and a martensite formed on oil quenching from the austempering temperature. It was intended, by varying the austempering time, to vary the quantity of the intermediate products between zero and 100 pct. The austempering temperature of 860°F was selected after extensive preliminary tests close to the nose-temperature. Austempering at this temperature yielded an acicular intermediate product. .Additional tests under less exacting conditions were made for an austempering temperature of 950°F where the intermediate product appeared to be very fine pearlite. To determine the effects of tempering on structures containing various amounts of

Jan 1, 1949

By Chas. A. Dobbel

The Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. Pmine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the Gear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was used to drive prospect holes with jointed steel. Just what equipment to develop for this work with the hammer drill involved much experimenting, as nothing was found in the literature

Jan 1, 1925

By Anthony Anable

HOOVER DAM, rapidly nearing completion in the Black Canyon of the Colorado River at Boulder City, Nev., taxes the superlatives of the vocabulary to describe. For by all odds, it is the largest construction project of its type ever essayed by man and the plants providing the essential materials of construction are also in a class by themselves not only in size but in advanced design, mechanization, and accurate control. Picture, if you will, the great aggregate plant, as it is called, situated about 4 mi. upstream from the site of

Jan 1, 1934

By W. A. Cole, E. L. Derby, J. F. Wolff

Exploration of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. The churn drill used is the Mesabi type and its operation should be described as "water jetting." The drill rods are washed down by the combination action of the water jetting from the bit at the lower end of the rods and the churning motion given the line of rods. The water, which is forced down through the rods, comes up between the wash rods and the casing, bringing the choppings to the surface. It is caught in three or more barrels, each of which has a stoppered hole 8-10 in. from the bottom. These barrels are successively filled, allowed to settle, and drained to the hole, until the desired depth is drilled. The sediment from each barrel is transferred to a settling tub in which it is allowed to settle; the water is then drawn off and the wet sample is collected and dried. The number of barrels used depends on the character of the ore. For example, when drilling sandy ores, all the wash water is caught and settled for the proper length of time without refilling any of the barrels. Thus, the sediment held below the stoppered hole in any one barrel is not disturbed. The casing is kept as near the bottom of the hole as practicable to prevent the caving of the hole from jeopardizing the sample. While the casing is being driven down and the hole is being washed clean after casing, the return water is not run into the sample barrels. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the importance that may be attached to certain characteristic strata in different formations. The following instructions for the care of core samples are issued by the Ogle-bay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan:

Jan 1, 1925

By George Stone

THE method of making oxide of zinc direct from the ore was invented and developed at the works of The New Jersey Zinc Co. at Newark in the middle of the last century. The process was invented by Burrows, who had not the ability, financial or technical, to work out the details necessary to make it of commercial value. This was done by Col. Wetherill, whose name is commonly attached to this process. The, grate bars used are also frequently called Wetherill grates, which is a misnomer because they were in common use for boiler firing at the time and he never claimed their invention. The invention of the process was due to the efforts of The New Jersey Zinc Co. to find a profitable means of working the ores from Franklin and Sterling Hill, N. J. These are a mixture of franklinite, willemite and zincite, containing about 20 per cent. of zinc. The first attempts were to make spelter, which were not successful, owing to the low grade of the ore and the fusibility of the residue. Failing in this, the next attempt was to make oxide in large muffles and reverberatory furnaces. This succeeded, although the cost of operation was high, the recovery low, and the quality of the product uncertain. In 1855, the new process was patented and has been in successful operation ever since. Essentially, the process is to spread a mixture of coal and ore on a body of burning coal on a perforated grate and blow an excess of air through the grate. The zinc is reduced in contact with the coal, volatilizes and burned by the excess of air in the upper part off the furnace and in the flues. It is then carried to the hag rooms by the excess air and products of combustion which are forced through the flues by fans. In its main features, the process is the same today as at the time of its invention, but the details have been so modified that it would hardly be recognized by its originators.

Jan 9, 1917

All the TECHNICAL PUBLICATIONS and PREPRINTS published in 1932 are available at Institute headquarters. They are also on file in public,, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division;. G-Petroleum .Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of PREPRINTS may also be obtained from the Secretary's office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. METAL MINING TECH- NICAL PUBLI- - TITLE AUTHOR MEETING TRANS. CATION VOLUME No. AND PAGE* 484-A.45 Propeller Type Mine Fan at Moose A. S. Richardson New York 102, 86, 93 F.52 Shaft, Butte, Montana (13) Feb., 1932 487-A.46 Progress in the Improvement of Max H. Barber New York, Methods and Equipment at Feb., 1932 Open-pit Iron Mines on the Lake Superior Iron Ranges (9) Pre. Sand Filling through Pipes and Lucien Eaton New York, 102, 33, 41 Boreholes (9) Feb., 1932

Jan 1, 1932

By D. J. Salley, M. Burke, G. L. Simard

A PREVIOUS paper1 described experiments on the interaction of dithiophosphate with galena and suggested that the process had characteristics of both chemisorption and surface chemical reaction. In order to add to this knowledge, a study has been made of the competition of a second ion with the dithiophosphate for a galena surface. Use again was made of radiotracer methods. Since radiophosphate was readily available, it was chosen as the competing ion. It is a feature of the tracer method that, in spite of similarity in the chemical behavior of the ions, the measurement of one ion in the presence of another can be made as simply as if only one ion species were present. In order to study the competition effectively, it naturally was necessary to examine the interaction of phosphate with galena alone as well as in the presence of dithiophosphate; consequently, this report consists of two parts. The first is devoted to a study of the rates, the isotherms, the desorption, and the exchange in the phosphate-galena system in the same manner as was done for the dithio-phosphate-galena system. The second portion is concerned with the studies on the competition. Flotation experiments on the three-component sys- tem are also outlined and the relationships involved are discussed briefly. The experimental method was that of the previous paper. The preparation of the galena, the radioactive and the nonradioactive dithiophosphate, and the procedures for radioactive counting, for sorp-tion, and for flotation measurements were identical to those previously employed. The radiophosphate* was used in the form of disodium phosphate solution. In the competition experiments the effect of the phosphate ion in depressing dithiophosphate uptake was followed by holding the initial concentration of nonradioactive phosphate constant while varying the initial concentration of the radioactive dithiophosphate. Counterfashion, the depression of phosphate by dithiophosphate was obtained by keeping the initial nonradioactive dithiophosphate ion concentration constant and altering the initial concentration of the radioactive phosphate ion. All solutions were buffered at a pH of 7.8 a0.1 by 20x10-' mol per cc of sodium carbonate. Measurements with radiocarbonate indicated that little or no carbonate could be sorbed in the presence of

Jan 1, 1952

By Dale A. Augenstein, S. C. Sun

A primary concern in the solution of any solid waste disposal problem is the characterization of the material. In the past, available methodology for the determination of coal refuse characteristics has been severely limited by the inseparable combination of organic and inorganic matter of which the refuse is comprised. The recent development of an electronic, low temperature asher which removes the organic material without alteration of the inorganic constituents has opened new areas of coal and coal refuse research. This study deals with the development of methodology for the characterization of Pennsylvania anthracite refuse through utilization of the low temperature asher. Seven samples of anthracite refuse were examined for verification of the methodology developed and information concerning the characteristics of the refuse.

Jan 1, 1975

By H. B. Fuqua, B. E. Thompson

The area discussed in this paper, commonly known as the West Texas district, is easily divisible into three geologic provinces, the Midland Basin to the east, the Delaware Basin to the west and the West Texas structural platform separating these two. Production in Garza, Scurry, Mitchell, Howard, Glasscock, Irion, Reagan and central Crockett counties is associated with the east flank of the Midland Basin. That in Loving and Reeves counties is associated with the Delaware Basin. All other production and developments discussed in this paper belong to the province of the West Texas structural platform. Because of certain developments that have occurred during the past year, it has been found necessary to slightly revise one of the fields as grouped by Mr. Reith in last year's paper1. The Scarborough-Leck field has been broken down as follows (Table 1): The Leck field is shown separately because it is producing from dolomite; while the Scarborough area, producing from sand, is regrouped and designated as " Scarborough-Kermit-Halley," which includes the producing sand belt across Winkler County from Ward County to New Mexico. It is believed that this is a more logical division of Winkler County and that considerable future work will be avoided by making this change before further production figures have accumulated under the present set-up. A number of new fields are listed in Table 1, some of which may represent extensions of other produeing arras. The authors, however, are inclined to believe that they represent new fields. In either event, less work is involved ill adding two areas together, if they later prove to be one, than in attempting to separate a maze of production data into two fields after they have been erroneously carried as one for a number of years. The Howard-Glasscock field is designated in this review as the Chalk-Roberts field and the Denman production on the Howard-Mitchell County line is included in the Iatan field. Development during 1934 Development in West Texas during the year 1934 showed a marked increase over the previous year both in exploration and ill exploitation

Jan 1, 1935

By William D. Klopp, Joseph R. Stephens

Chromium alloys were coated with silicon, alumi-nuw, and boron by pack cementation. None of these simple coatings provided adequate nitridation/oxida-tion protection for a Cr -0.17pct Y alloy substrate as shown by a substantial Increase in the ductile -brittle transition temperature after air exposure for 100 hr at 2100°F. Iron-modified silicide coatings afforded good protection, holding the transition temperature of air-exposed specimens to 350° F compared to 200° F for uncoated unexposed specimens and 800°F for un-coated exposed specimens. Additional attractive cant-binations of modi-tying elements included Fe-mo, Fe-Mo-W, Fe-,Mo-W-Ti, and V-Mo-W-Ti. THE desirability of increased operating tempera-tures as a mcans of improving the performance of ad-vanced air breathing engines has resulted in emphasis on the development of materials with high operating temperature capabilities. Chromium, because of its relatively low density (7.19 g per cu cm), high melt-ing point (3410°F), and adequate strength upon alloy-ing, is a candidate material for turbine buckets and stator vanes of advanced air breathing engines. How-even, chromium is not without severe limitations, the major one being susceptibility to nitrogen embrittle-ment upon exposure to air at high temperatures.1,2 For example, a 25-hr air exposure of a Cr-5 pct W* * All compositions in wt pct. alloy at 2100°F produces a 600°F increase in the duc-tile-brittle transition temperature.' Although dilute alloying with such elements as yttrium, lanthanum, arid thorium3,4 or strong nitride formers5 has been shown capable of reducing nitrogen embrittlement, it is apparent that some additional form of surface protection, such as coatings or claddings, will be required for long time service in air breathing engines. Studies of aluiminide6 and silicide7 coatings and of nickel-base claddingsl on chromium alloys to date have suggested that these protection systems are inadequate. Of the aluminidc systems Studied,6 a simple aluminum and an Fe-Al coating on a Cr-5 pct W-0.1 pct Y alloy showed the lowest air exposure weight gains. However, the air exposures raised the ductile-brittle transition temperature of the coated specimens to above 1600°F from an initial level in unexposed specimens of about 500°F. A second in-vestigation for protection of Cr-5 pct W-0.1 pct Y employed gas pressure bonded alloy foils as protective claddings.1 An aluminized Ni-20 pct Cr-20 pct W alloy plus an unalloyed tungsten barrier layer gave the best performance with air exposure lives based on appearance and weight gains of over 600 hr at 2100°F. However, the bend ductile-brittle transition tempera-ture was increased to at least 1000°F after 100 hr at

Jan 1, 1970

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By Norman B. Pilling

The technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost' exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105' C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys. The reagent consists of a dilute solution of nitric acid and methyl alcohol in nitrobenzol. It is a great advantage to secure an anhydrous solution, as a tendency toward acidic etching has been traced to small amounts of water. A convenient method of preparation is to make an anhydrous stock solution of nitric acid in methyl alcohol in the proportion 20 per cent. acid by weight (12.5 per cent. by volume). The alcohol can

Jan 1, 1924

By E. J. Bruderlin

A metallurgical process to be economically successful must be carried on under proper conditions of control and equipment. The question of equipment is always of primary importance. In the distillation process for the recovery of zinc by retorting, the retort is the all-important piece of equipment. Each retort in a working blóck must function as a separate unit. Over-all block efficiency is the result of the ability of the individual retort to withstand the severe conditions of operation for a maximum period of time. Therefore retort manufacture has been an ever present problem with the operator of a zinc-retorting plant. During recent years the zinc-plant operator has been faced with rapid changes in the character of the ores and concentrates. Operating costs have increased as a result of the introduction of the flotation process and the amount of flotation concentrates to be handled. To counteract increasing costs, the operator has found it necessary continually to attempt heavier loading of retorts, until a 45 to 50-lb. charge per cubic foot of retort space has become common practice. Heavy loading has brought about severe firing conditions, which, in turn, have emphasized the necessity for further improving the quality of the retort. Increasing percentages of detrimental impurities in the retort charges have also added to the operator's difficulties. Amarillo Silicon Carbide Retorts At the Amarillo plant of the American Smelting and Refining Co. a retort made of a suitable plastic clay grogged with silicon carbide has been found to best meet the present-day requirements. Retorts of this kind have been in use at Amarillo for 8 years and have shown an average furnace life of approximately 175 calendar days. The Amarillo retort is cylindrical in shape and after burning is approximately 83/4 in, inside diameter by 60 in. over-all length. The wall thickness is 136 in., except for the butt of the retort, which is approximately 2½ in. thick. The retort mud has a shrinkage of 3 per cent, or approximately % in. per foot. The silicon carbide retort after being properly dried weighs about 211 lb. When the retort is fired and ready to go into use the weight decreases to approximately 203 lb.

Jan 1, 1937

By A. B. Kinzel

MUCH work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. . This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it con-stitutes the main action in the usual steelmaking processes. A. L. Feild1 has formulated a basic differential equation expressing the open-hearth reactions and Hefty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action. to the reaction FeO +C ?? CO +Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed' constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Feild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X 10-2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By Theron Wasson

Discoveries in Michigan, which at the beginning of the year 1934 indicated possible new areas, did not develop into fields of market-breaking proportions. Hart, Oceana County, developed small production from the Traverse lime. Edmore, Montcalm County, proved a small area for oil from the Traverse. West Branch, Ogemaw County, previously reported as Ogemaw, had quite a drilling campaign but was somewhat disappointing because wells were small and erratic. During the year, 30 wells were completed at West Branch, and at the end of the year 15 others in and around this field were under way. At West Branch the Traverse lime, found at 1800 ft., has thin porous streaks near the top, which make small wells; the Dundee lime at 2800 ft. produces from a porous zone of varying thickness. Over the entire field the Dundee wells average 10 to 20 bbl. per day. Acid treatment has materially increased production from some Dundee wells in this field. About 3000 acres have been proved productive from the Traverse and Dundee. At the close of the year the well in Beaverton township, Gladwin County, is probably the most discussed of any in Michigan and may be opening a new field of some proportions. It had an initial production of 70 bbl. daily from the Dundee lime at 3830, which has decreased to 25 bbl. per day. Deeper drilling into the lime may increase production. During 1935 the area around this test will probably be the most active in the state. Structural conditions in Gladwin County, as in other parts of Central Michigan, are obscured by a thick mantle of glacial drift and it will take considerable drilling to outline subsurface conditions accurately. The most important new shallow gas area of the year is around Edmore in Mecosta and Montcalm counties. Eight wells have been drilled to the Michigan stray and the upper Marshall sand, having a combined initial production of 30 million cubic feet. These gas wells are scattered over so wide an area that an estimate of proven territory cannot be made until more drilling is done. At the present time no gas is being sold from Edmore.

Jan 1, 1935

By A. C. Fieldner

In November, 1926, the American Engineering Standards Committee (now the American Standards Association) called a meeting of representatives of various professional societies and industrial, educational and governmental organizations to consider what action, if any, should be taken on the classification of North American coals. This meeting was called because a system for the use classification of coal, proposed by George H. Ashley, had been referred to the committee by the Coal Mining Institute of America. This meeting, at Pittsburgh, was well attended and was definitely in favor of taking up the whole question of scientific and use classification of coals, including all the various ranks from lignite to anthracite. The American Society for Testing Materials was recommended as the sponsor organization to take charge of the work and organize the sectional committee according to the rules of the American Standards Association. The American Society for Testing Materials proceeded with the organization of the sectional committee, holding a meeting in Philadelphia, June 10, 1927. Officers were elected, regulations adopted, and general plans for carrying out the work were outlined. The total membership of 28 comprising the sectional committee consists of 8 producers, 2 distributors, 9 consumers and 9 members representing general and scientific interest. From this committee three technical committees of 10 to 12 members each were organized: Scientific Classification, H. J. Rose, chairman; Use Classification, W. H. Fulweiler, chairman; Marketing Practice, F. R. Wadleigh, chairman. The Technical Committee on Scientific Classification was requested to formulate a system of coal classification based on chemical and physical properties of coal and with reference to origin and constitution. The Technical Committee on Use Classification was charged with developing a system of classification, if possible, based primarily on the uses of coal and commercial practice; this system to be correlated with the scientific system as far as possible and desirable. The Technical Commitlee on Marketing Practice was formed to collect and collate information on commercial practice for the benefit of the other two committees. The first meetings of the technical committees were held on Nov. 17, 1927, and the first informal progress reports were submitted to the

Jan 1, 1930

By Gerald Sherman

IN the southern field of the anthracite region of Pennsylvania, many of the coal seams dip at angles of 40° to 50° from the horizontal. For transportation purposes, "tunnels" are driven across the coal measures and, occasionally, "rock gangways," beside the seams and parallel with them. The use of gangways driven in country rock appears to be increas-ing, as they avoid the maintenance' of long gangways in coal, which eventually are driven to the colliery boundaries, and permit mining from a number of intermediate blocks without interference. The rock consists of slates or sandstones of moderate hardness, which may range into very hard, highly siliceous, fine-grained conglomerates. In this distinctly bedded formation,' the direction of the heading, whether parallel with or across the structure, makes it necessary to distribute the drill holes in a different pattern to break the ground, but does not change loading conditions. In 1932, practically all the mucking was done by hand, and it was the established custom to use four men on two drills for drilling and breaking the ground, and five for loading it, out. A driver and mule was needed in addition, to assemble the rock cars at a siding or branching track in the rear, pending their final disposal. This might occupy the driver's whole time, or if the length of haul were short, he might be able to do other useful work. It was thought possible in 1932 to reduce the cost of driving such headings in rock by mechanical loading, and to investigate this subject a scraper loader was used in a section of tunnel then being driven. Opera-tions while driving 195 ft. of this tunnel using a scraper loader were care-fully observed. Time studies were made of the loading, and records made of the routine of breaking ground, but not in such detail. Tunnels or gangways in the colliery are 7 ft. high above the rails, by 10 ft. wide, which requires a minimum of 8 ft. in height, broken to allow for rails and ties. This cross section is of sufficient size to permit the use of any one of several types of power loaders, but for this demonstration if was found most convenient to use a scraper loader.

Jan 1, 1936

By P. S. Kotva

Dislocation substructures in superalloy matrices of varyzng co)npositions have been studied. In general, it has been found that the alloys can be classified into ''high", ''medium", and "low" stacking fault energy classes based on the type of dislocation substructure observed in the matrix and that the substructure can be correlated to the stacking fault energy. The effect of different types of dislocation substructure and dislocation reactions on the intragranulur precipitation of carbide phases has been studied. In a Ni-Cv-Mo-Fe matrix, precipitation of MC carbides in association with stacking faults has been observed. In most superalloys, solid-solution strengthening and precipitation hardening are the chief mechanisms employed to achieve strength. The latter contribution to strength is usually achieved by the precipitation of / in certain wrought alloys. Insufficient attention has been given to the problem of obtaining strength in su-peralloys by controlling precipitation of carbides on imperfections within the matrix. The present work was undertaken to investigate the dislocation substructure in various superalloy matrices, to study the effect of such substructure on subsequent precipitation of carbides in the matrix, and to investigate whether certain modes of precipitation of carbide phases found in austenitic stainless steels2"4'6 would occur in nickel-base alloy matrices with dislocation substructures of the same type as those found in austenitic steels. 1) EXPERIMENTAL TECHNIQUES Five-pound heats of the various alloy compositions reported here were vacuum-cast. The ingots were given light deformation by rolling to break up the as-cast structure and then homogenized for 24 hr. HASTELLOY alloy X (nominal composition: Ni-2OCr-17Fe-8Mo-0.05C) was homogenized at 2150°F and In-cone1 625 (nominal composition: Ni-20Cr-5Fe-8Mo-3.5Cb-0.05C) was homogenized at 2280°F. Fabrication of 0.004-in. sheet was achieved by cold rolling with intermediate annealing treatments being carried out at the same temperature as those used for homogeniza-tion. Each solution anneal was followed by quenching. The aim of this procedure was to redissolve as much of the primary carbide phase as possible. Samples of the 0.004-in. sheet were cut and encapsulated in quartz capsules and then heat-treated in the tube furnaces. Thin foils were prepared using an ethanol-10 pct perchloric acid bath at 32°F and at a voltage of 22 v. A "window" technique was employed. Observations were made on a JEM-7 electron microscope operating at 100 kv. 2) EXPERIMENTAL RESULTS a) Types of Dislocation Substructure. Fig. 1 shows a schematic correlation between stacking fault energy, SFE, and the type of dislocation substructure observed in various matrices of nickel- and cobalt-base alloys. A precise quantitative determination of stacking fault energy is not implied in the figure but the correlation between stacking fault energy and the type of dislocation substructure obtained allows alloys to be divided into three classes in analogy with the classification employed by Swann and ~uttin~' for binary alloys of copper. Class I alloys are associated with a "high" SFE and show a cellular substructure of dislocations as typified by the micrograph of a thin foil of pure nickel deformed 4 pct at room temperature in Fig. 2. With decreasing SFE the tendency toward cell formation is lessened and dislocations tend to be arranged in coplanar groupings. Examples of this class of alloys with "medium" SFE are provided by the mi-crostructure of solution-heat-treated, quenched, and deformed thin foils of HASTELLOY alloy X, "Waspaloy" (prior to any aging), and Inconel 625. Fig. 3 shows a thin-foil micrograph of an alloy of Inconel 625 composition, solution-heat-treated, quenched, and deformed 5 pct at room temperatures. No evidence of any cell structure can be obtained in materials of "medium" stacking fault energy, Fig. 3, even after severe deformation. The stacking fault energy of the alloy shown in Fig. 3 is, however, not low enough to make the dissociation of dislocations visually obvious. As stacking fault energy decreases further, with successive addition of solute in the matrix, there is an increased tendency toward dissociation of dislocations and cross slip becomes progressively more difficult. Eventually, when the stacking fault energy is "low" enough, complete dissociation of dislocations is seen to occur as shown in Figs.

Jan 1, 1969

By T. A. Wright

The sampling of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grat) sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases rnuch material can bc sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to incrcase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to makc sorting and grading more difficnlt in turnings, borings, clippings, etc., and conseqllcntly is making sampling of more moment. In tin, lead, alumiinum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosscs, battery lcad, and aluminunl skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or "metallic yield." Coppcr and Icad wastcl, howcvcr, is being sold more and more on actual copper and lead contents bascd on sarrlple and chemical analysts. This paper will be dcvotctl chiefly to the sampling of niaterials suitablc only for refining and recovery of one or more of the metals present. The methods described are often bascd on thc fact that but one, metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect thc final copper result, as the "after-melting" assay can be readily calculated to the "bcfore-nltltingl' basis, but if smelter efficiency continues to increase, so that in tiltie zinc, for instance, may be rccovrred on a paying basis, thc method of sampling dirty brass, for example, will have to bc changed also. As a matter of fact, we may cxpect that improved refining proresses will make possible the partial reeovrry of lcad and tin which are now lost