Search Documents

By C. B. Thwing

IT is likely that among most races, owing to the ease of finding and working clay, the making of clay utensils was learned earlier than the molding of metal implements. The ancients made good pottery and durable brick in kilns that wasted fully one-half the heat and spoiled fully one-fourth of the ware; and, taking the clayworking industry as a whole, we are doing the same today. The chemical and physical changes involved in the burning of clay are so many and vary so much with the composition of the clay that it is not surprising that the rule-of-thumb methods so commonly employed fail to give uniform results. In its passage from plastic clay to the vitreous or stonelike character the mingled minerals and accidental organic impurities of which the clay is blended must pass through four stages, the second and third usually overlapping, and the fourth often beginning before the third is complete. These stages in their order with the rising temperature are drying, dehydration, oxidation, vitrification. In the first part of the drying stage, usually accomplished in part outside the kiln, the water mixed with clay is dried out at temperatures not much exceeding the boiling point of water. In the later part of this stage, within the kiln, the hygroscopic water, absorbed from the air is expelled at somewhat higher temperatures, this stage being known as watersmoking. Some clays are very sensitive to temperature during the drying stage and if the temperature exceeds 100°, the ware becomes checked. Other clays may be dried more rapidly without danger. In down-draft kilns, the draft is slight during the watersmoking stage and the water driven off from the top rows condenses on the ware in the bottom of the kiln, with the result that high temperatures are likely to be reached at the top of the kiln before the bottom is fully dry. The lag in temperature of the bottom persists to the second stage in spite of the better draft then prevailing.

Jan 9, 1919

By R. L. Slobod, C. Gatlin

This .study defines the basic mechanism of the mis-cible displacerrzent of oil and writer from porous Medici by various water-driven alcohol .slugs. Three distinct alcohol slug processes were .studied. Considerable data concerning the quanity of alcohol required for oil recovery were also obtained. All data were obtained in a 1-in. diameter, 100-ft long, unconsolidated core. The porosity of this system was 35 per cent. and the permeability was approxitrlately 4 darcies. Total core pore volume wax 5,716 cc. All displacements were conducted at a constant injection rate of 5 to 6 cc//min, which corresponds to a frontal advance of 5 ro 6 ft/hr. The first portion of this paper is concerned with 111 use of one alcohol—isopropyl—a\. the slug material. Isopropyl alcohol (IPA) is completely miscible with both oil rind water; however, miscibility of the threc-component systems, oil-water-IPA, requires a relutively. high concentration of IPA. Hence, the displocement is not of the misoible type unless the IPA concentration is maintained above some critical value. A slug of IPA equal to only 13.5 per cent of the pore volume was jound to be sufficient to obtain complete recover?, of residua1 naphtha. In later studies two distinct process variations were developed. The firsr of these utilized methyl alcohol (MA) and IPA as slug materials. It was shown that methyl alcohol may he substituted for IPA at the front and rear of the slug with no loss of oil recovery. A .slug of 4 per cent MA-4 per cent IPA-4 per cent MA was sufficient for complere oil recovery. Because MA is considerably cheaper than IPA, this represents an important step toward economic application. A .second process variation used normal butyl alcohol (nBA) and MA as the composite slug, the nBA segnzent being injected first. This technique requires the smallest total slug size (approximately 10 per cent) of all processes studied. The high cost of nBA, however, precludes commercial application. It is possible that this basic process, subject to changes of alcohol type, may lead to a commrercicil process. INTRODUCTION Within the last 10 years, considerable study has been devoted to the general mechanics of miscible phase dis- placements in porous media. These studies have. in general, dealt with two-component displacernent. All reported field trials to date have been modified gas drives of one type or another. These utilize either lean gas at high pressure, rich gas at lower pressure or an LPG slug. The irreducible water content of the reservoir remains immobile during these processes. Although these techniques hold great promise. certain drawbacks do exist. Poor areal sweep efficiency, inherent in any displacement having a highly unfavorable mobility ratio, is one disadvantage. Furthermore, the miscibility of all processes which use gas is dependent on pressure. These pressure limitations may prohibit application to shallow reservoirs. There are also many areas where large quantities of LPG and natural gas are not readily available. These factors emphasize the need for improved techniques. The alcohol slug process is also a miscible-phase displacement process. It differs from the previously mentioned two-component techniques, however, in that both the reservoir oil and water are displaced by the slug. This behavior is a consequence of the miscibility of certain oil-water-alcohol systems. In the simplest case, a relatively small volume (slug) of an alcohol (such as isopropyl) is injected into the system. Water is then used to drive the slug through the medium. Thus. three components—-alcohol. oil and connate water-—exist at the front side of the slug. Miscibility is obtained at some alcohol concentration, this being dependent on the solubility of the particular system. Miscibility is maintained within the slug until the alcohol concentration falls below that value required to maintain miscibility. When miscibility is lost, the process reverts to a water flood. Certain inherent benefits of this technique are apparent. High pressures are not necessary to obtain miscibility in these liquid systems. Furthermore, water is a more desirable driving agent than gas because of the improved mobility ratio and the attendant improvement in areal sweep efficiency. The main disadvantage is, of course, the relatively high cost of alcohols. The use of an alcohol slug to recover reservoir oil is not a new idea." ' However, this process has received only limited study, presumably due to the lack of industrial interest caused by the seemingly prohibitive cost of alcohols. The main purpose of this study was to investigate the mechanism of the displacement of oil and water by various alcohol slugs and to develop process modifications aimed toward possible commercial application.

By Sam Harlan

At intervals during the past several years the oil industry has been confronted with the problem of forestalling crises in its affairs. These crises have been reduced to periods of depression which, fortunately, the industry has been able to survive. Under the existing competitive practices which control the producing division of the industry it apparently has been proved that the best efforts logically to curtail development and producing operations are inadequate for effecting a true production balance and the consequent stabilization of prices. The industry is awakening to the fact that the situation warrants revolutionary thought and at this time it is looking for a permanent solution of its problem in a general plan for unit development and operation such as the one first proposed by Henry L. Doherty. Mr. Doherty's proposal was designed not only as a means for stabilizing the industry as a whole, but its principles involve very definite potential benefits for the average individual operator and royalty owner as participants in pooled projects. The benefits to these individuals would be derived from maximum recovery, the maximum utilization of natural energies, the minimization of development and operating costs, enhanced values of leases and royalties through improved efficiencies and ultimate yields, improved earnings through stabilized crude oil prices, etc. This plan was revolutionary to the industry's practices and at the time was rejected, but it now appears that the development and operating policies for new properties are continually approaching the ideal of the original plan. Oil companies are constantly extending their efforts to improve all factors that have a bearing on the costs and efficiencies of their operations. These efforts may, in some degree, be a normal outgrowth of the industry's progress, but the forced consideration of market conditions, the growing appreciation of the importance of regulating operations for maximum ultimate economies and the depreciation of the old principle of maximum flush at any cost, come from a new school of thought which has been stimulated by the immediate pressure of overproduction and

Jan 1, 1930

The first National Industrial Conference was disbanded without accomplishing the results hoped for. A second conference is to be called in the near future. In response to suggestions of members of the Founder Societies, the following telegram was sent, Oct. 29, to the President and each member of his cabinet. "Engineering Council respectfully recommends appointing on new Industrial Conference two or more engineers familiar with industrial problems. Council represents five national societies of professional engineers having forty-one thousand members. Washington office in McLachlen Building."

Jan 12, 1919

By Paul G. Hoffman

A survey of the role of the United Nations Special Fund in the field of mining and metallurgy. An aircraft, manned by Canadians and crammed with modern scientific instruments, crisscrosses over the dense rainforests of tropical Surinam at Y4 kilometer intervals, prospecting for valuable mineral deposits. Mill head samples of Burmese lead and zinc ores arrive at a Colorado laboratory for analysis and experimentation to determine the best milling and ore-dressing techniques. At the new Institute for Applied Geology in Manila, Philippine mining engineers receive instructions from a Finnish petrologist. These scenes illuminate only a fraction of the exciting work in the mining and metallurgical fields being carried out by the United Nations Special Fund.

Jan 8, 1963

By H. Hooykaas

A few years ago Marsal published a method of predicting oil recovery as a function of time for an edge-water-drive reservoir with several rows of wells.' The method is based solely on oil- and water-production data obtained during a short period for the first row of wells and the gross productions (past and future) of all wells. This paper presents a streamlined version of the original publication and experimental evidence showing the reliability of this version. For this purpose scaled experirnents were performed in a large model (750 X 500 X 23 cm, 24.4 ft X 16.2 ft X 8.9 in.) in which edge-water-drive reservoirs with three rows of production wells were simulated. From the results of the experiments it is concluded that the method gives a fairly accurate prediction of the future production behavior of the reservoir and enables us to select the most profitable production plan. Results obtained with the method were always slightly conservative. INTRODUCTION The calculation method developed by Marsal aims at forecasting future reservoir behavior.' It can be applied to floods in which a number of down-dip wells are rapidly going to water. Essentially it is a method for predicting the future behavior of the up-structure wells on the basis of the observed behavior of the down-structure wells. As such, the method is especially useful for predicting behavior of edge-water drives toward several rows of wells. The requirement to be met for justifying the approach is identity of production mechanism in all regions of the reservoir. The attraction of the method then lies in the fact that it applies even when we have no complete description of the prevailing production mechanism. The original publication was in the German language and for this reason, perhaps, did not attract widespread attention. In our opinion it deserves to do so because it does offer in a simple way results which are in fair agreement with observed data. The aim of the present paper is to bring the method to the attention of a wider audience. The method in its most simplified form is reviewed and experimental data in support of it are presented. PRINCIPLES To show Marsal's principle. we will first write the continuity equation for very simple conditions, linear flow (in the positive x-direction) in an incompressible porous body [cross-section A(x), porosity +(x)], saturated with incompressible fluids (oil saturation S). When the oil in this formation is displaced by water, injected at x = 0 (inlet face), we get where q(t) is the total gross displacement rate and f the fractional oil flow. The equation can be solved if we make the assumptions: (1 ) that the fractional oil flow (f) is a univalent function of saturation (S); and (2) that the function is the same throughout the porous medium. Then: f = f(S) Solving this equation with the method of characteristics, we obtain

Jan 1, 1966

By Jeffrey W. Nelson

Predictions of creep closure for periods ranging up to more than 1,000 years are needed for designing a radioactive waste repository in a salt formation. Such long-term predictions must be based on the use of laboratory and field test results extrapolated by numerical modeling. Laboratory test results are presented which show highly variable creep behavior for salts from different sites as well as salts from the same site. Comparisons of measured creep closures against predicted closures are presented for two deep boreholes in Louisiana salt domes and for an exploratory shaft and drift in southeastern New Mexico bedded salt (WIPP). These data illustrate the significant uncertainties involved in long-term closure predictions and indicate the critical need for site-specific, in situ closure measurements over extended periods of time for repository design.

Jan 1, 1984

By H. Margolin, E. Ence

In order to understand the effect of zirconium on properties of Ti-Cu-A1 alloys, Ti-Zr alloys were examined for the presence of ordering or compounds at the following compositions in weight percent: 24.1 pct Zr (lZr:GTi), 32.2 pct Zr (lZr:4Ti), 38.8 pct Zr (lZr:3Ti), 49.0 pct Zr(1Zr:ZTi). Alloys were prepared as 15-g buttons by non- consumable arc melting under argon atmosphere from Bureau of Mines titanium (Bhn 63) and Reactor Grade zirconium (Bhn 150). Weight losses during melting did not exceed 1 pct of the initial button weight. Prior to heat treatment, buttons were hot-rolled at 600" to 700°C to rods of about 6 mm diam. Contamination after hot-rolling was found to extend to a depth of less than 0.5 mm. Specimens for heat treatment were wrapped in molybdenum sheet, annealed in argon-filled quartz capsules, and quenched by breaking the capsules under iced brine. Annealing times were as follows: 700°C — 7 days; 600°C— 14 days; 575°C-1 and 2 months; 525°C-2 months; 500°C-2 months. Prior to heat treatment, all Ti-Zr alloys were vacuum annealed at 900°C to remove hydrogen. The reanneal of 575°C specimens for an additional month produced no observable microstructure changes. The results obtained by microstructure and X-ray diffraction are shown in Fig. 1, together with data of Hayes et al.' No other phases than a or P were found. Small amounts of retained P were detected by X-ray in the 49 pct Zr alloy. The data of the present investigation suggests that ß and a transus boundaries are at considerably lower temperatures than those of Hayes et al. The work of Hayes et al. is based on sponge titanium and Bureau of Mines zirconium, both of which contained 0.15 pct 0. Since melting was performed in

Jan 1, 1962

By J. S. Miller

THIS paper describes the method of mining a steeply pitching anthracite seam on a heavy pitch in the Orchard vein in No. 1 Tunnel of the Lehigh Coal and Navigation Co. The Orchard vein in the Nesquehoning district has a thickness of about 15 ft. on the level of the gangway, which is sufficient thickness for the gangway to be driven full width in coal. Above the gangway, the vein becomes thinner and near the surface is about 8 ft. thick. The coal is of good hard quality and carries a fairly good roof. The pitch of the vein is between 65° and 70°. Usually the breast-and-pillar method has been employed in the mining of the steeply pitching veins in this section. This method produced good results as far as the mining of the breast was concerned but the recovery of the pillar was difficult as to full extraction and expensive as regards costs. To recover these pillars after the breasts were driven, three methods were commonly employed; they were known as the pillar-breast method, pillar-skipping method, and pillar-chute method. The pillar-breast method consisted in putting a battery in one corner of the pillar (Fig. 1), coupling the manways A and B of the two adjacent breasts for two or three lengths ahead of the working face of the pillar being cut, and working the pillar as a breast. This method was used by the more skilled miners of the earlier days but has practically been abandoned. A slight variation of this method is used to some extent. In this case, the pillars are left wider than ordinarily and of sufficient width for the full-width breast to be driven in and a small pillar left on each side of the pillar breast between it and the regular breasts. With the completion of the "pillar breast," the ribs are drilled full of holes, loaded, and fired.

Jan 3, 1925

By Tell Ertl

THE term oil shale is defined. Foreign oil-shale developments are outlined briefly, The richest and most extensive oil-shale deposits in the United States lie in Western Colorado. The Bureau of Mines is opening two adjacent areas for underground mining in Western Colorado. From the first area the oil shale is mined selectively as required by the retorting plant. The second area is being developed as a unit of a full scale oil-shale mine to ascertain the most practical methods of mining oil shale and to determine costs. In both of these mining areas, research will be carried on to develop new and improved practices for mining oil shale.

Jan 1, 1947

By Victor M. Braschi

The railroad history of Mexico began with the first presidential term of General Diaz. Concessions for the building of railroads had been granted in former years; indeed, an exclusive privilege was granted, August 22, 1837, to Francisco de Arrillaga for the construction of a railroad from Mexico to Vera Cruz, with a branch to Puebla, and other concessions were granted from then on at various periods; but the year 1877 was the real beginning of the regular and constant decelopment of the railways of Mexico. The programme laid out at that time by the new government, and responded to by the nation, was to develop its natural ele-

Jan 1, 1902

By Peter B. Nalle

Over a period of years the Crestmore plant of the Riverside Cement Co. has been supplied with limestone from the Chino limestone bed. The limestone bed dips about 40º and extends 1500 ft along the strike. Thickness of the bed is such that horizontal distance from footwall to hanging wall varies from 400 to 1200 ft. When the new room and pillar mining system was instituted the haulage units used for development were model C Tournarockers. Four of these diesel units were purchased with the idea of using them solely for development work since it was realized that they would have to be supplemented by additional, and perhaps larger haulers.

Jan 4, 1959

By J. P. Hammond, C. J. Sparks, C. J. McHargue

IN a study of the effects of solid solution alloying on the deformation texture of titanium, an alloy containing 3.8 pct A1 was found to develop a (0001) [1010] texture instead of the texture characteristic of pure titanium.ls2 A short investigation has been made of the change in texture with aluminum content. Alloys containing 0.27, 0.47, 1.05, and 1.43 pct A1 were prepared by vacuum arc melting, using iodide titanium as the base material. Homogenized ingots were reduced 90 pct in thickness by cold rolling. Pole figures were obtained using the usual film techniques. Fig. 1 shows that the change from the tilted to the nontilted (0001) position is gradual. The dashed contour lines in Fig. 1 indicate the extent to which data was collected. The addition of 0.27 pct A1 resulted in a decrease in the transverse spread of basal poles. With increasing aluminum content, the amount of the tilt becomes less and the region of highest intensity takes the shape of a ring about the center of the pole figure. For aluminum contents greater than 1 pct, the (0001) [1010] texture is definitely present—the sharpness increasing as the amount of solute is increased.* It is interesting to note that Williams and Eppel-sheimer9 eported for commercial grade titanium a high intensity region 20" toward the rolling direction from the rolling plane normal in addition to. one 30" toward the transverse direction. Their basal pole figure was similar to Fig. 1, row inree. The observation that the texture changes gradually with solute concentration is similar to the results of similar studies on copper." At the present time these effects are not clearly understood. Acknowledgments This work was sponsored by the Aeronautical Research Laboratory (WCRRL), Wright Air Development Center, under Contract NO. AF' 33(038)-19574. The authors are grateful for the aid received and permission to publish these results.

Jan 1, 1958

Efficient energy utilization in the electrolytic zinc process, relative to other zinc processes, is one of the reasons for its wide adoption in recent years, says John D. Siddle, zinc plant superintendent at the Bunker Hill Co., Kellogg, Idaho. Designers and operators of electrolytic zinc plants have pioneered process improvements, new equipment, and operating techniques to conserve energy. As energy costs increase it the future and competitive pressure mounts against less-efficient producers, these energy-saving improvements will he regarded as necessary for economic survival. Plant designers and operators should not lose sight of the savings in operating costs possible through intelligent utilization of all available forms of energy.

Jan 11, 1977

By H. B. Heller, T. J. LaChapelle

Phosphorus nitride has been used as a diffusant for introducing phosphorus into silicon under various conditions. It has a temperature -dependent rate of decomposition beginning in the 500°C range, increasing very rapidly above 1000 C, producing gas -eous phosphorus and nitrogen. Best control was obtained with a two-temperature arrangement, with silicon at the proper higher diffusion temperature. It is an easier compound to use than the usual P2O5 because it is nonhygroscopic and yields temperature-controlled surface concentrations together with excellent final surfaces. Surface doping nearly as high as that produced by phosphorus pentoxide has been observed for sources at 850" to 900°C. Reproducible high sheet resistances were obtained by using slow flow rates (1 linear in. per min) and staggered-baffle gas mixing with the nitride at 550°C. Both inert gas (argon, nitrogen) and oxidizing ambients have been examined. Oxygen reacts to produce anhydrous P2O5, consuming the source at a rapid rate. Nitrogen, except for short diffusion times, suppressed the dissociation reaction and sometimes produced inferior surfaces. Argon appears to be a more useful ambient. PHOSPHORUS is a common impurity atom which may be introduced into a semiconductor lattice to create a p-n junction or an nn contact region. Various investigators1-4 have described techniques which can be used with either elemental phosphorus or certain of its compounds. This paper discusses a newly available compound of phosphorus, phos- some processes silicon wafers are precoated with a phosphate glass which acts as the doping source. Although a nonoxidizing form like elemental phosphorus or a phosphine can be used, most diffusion methods usually involve the use of phosphorus pentoxide. Because of the rapid volatility of this compound, a two-step process is often used, combining a gaseous deposition to introduce a predetermined quantity of phosphorus into the silicon with a later redistribution to obtain the desired distribution and surface concentration. Such a process usually involves predepositing phosphorus at surface concentrations greater than 1020 cm-'. At such doping levels the phosphorus-diffusion coefficient appears to be strongly concentration-dependent.596 Distribution profiles5'9 for these high concentrations of phosphorus do not follow Fick's laws, having extended subsurface regions which appear electrically to be nearly uniformly doped with ionized impurity atoms. Radioactive-tracer experiments also show near-surface anomalies in the distribution profile. Additionally, it has been shown1' that the introduction of very high surface concentrations of impurity atoms into silicon (a step necessitated by the subsequent lowering of concentration during the redistribution) creates dislocations, even in material having no dislocations originally. For device fabrication the use of oxide masking introduces certain difficulties and limitations.7'8 The standard practice of using phosphorus pentoxide as an impurity source adds other problems to these because of the speed and ease with which this compound reacts with moisture present in any gas in contact with it. In fact, P2O5 is one of the fastest and most effective drying agents for gases. Because it is such an excellent desiccant, completely anhydrous phosphorus pentoxide is difficult to obtain and is even more difficult to keep dry. Adequately dry gloved boxes must be used for storage and transfer of the chemical. The presence of even traces of moisture will cause formation of phosphoric acids which, during the high-temperature diffusion, results in polyphosphoric acids of variable composition. Such reaction by-products end up as gradually accumulating viscous fluids in the cooler parts of the diffusion furnace. The calculation of the final solute distribution for

Jan 1, 1964

By Fred C. Bond

The process of comminution by grinding is properly classified as an art, rather than as a science. Like most other operations concerned in ore dressing, or in the treatment of nonmetallic minerals, the mathematical relationships of rock breaking are still obscure, and much disputed. If some basic formula exists, comparable for instance to E = RI in electricity, it has not yet been placed in common use. The absence of such a comprehensive mathematical background undoubtedly is the cause of many inefficient designs and installations, as well as of much poorly oriented experimental work. On the other hand, the mathematical immaturity of the process constitutes an opportunity for a real contribution on the part of those who enjoy mental pioneering. Some of the statements made in any such exploratory work may be little more than opinions, and it is to be expected that some will later be proved untrue; but such an evolutionary development is necessary if we are ever to arrive at the fundamental laws, the discovery of which can change the empirical art into a mathematically exact science. The most significant principle of comminution that we possess is probably Rittinger's law, which states that the work done in crushing or grinding is proportional to the area of the new surface produced. There is an alternative theory, known as Kick's law, which formerly was preferred to Rittinger's but which now is rather discredited. According to Kick, the work done in comminution is proportional to the volume, or weight, of the pieces broken, or to the cube of their diameters, while according to Rittinger it is proportional to the square of the diameters. Careful determinations of size distribution below the limit of sieve sizes1 indicate strongly that under ordinary grinding conditions the amount of new surface area produced is directly proportional to the net power input. Changes in the size ratio between the balls and the particles cause important differences in the proportion of the product that passes a given mesh size, but do not affect the total amount of new surface area; they merely change the distribution of the surface among mesh sizes. The principle of constant surface area is the logical result of Rittinger's law, and it may well have an important bearing on the comminution theories of the future. Formula for Ball Wear Grinding tests have been made in the Allis-Chalmers laboratory for more than 9 years, using a standard charge of mixed balls of different sizes; and a continuous record has been kept of the rates of wear of each size. These results have been combined and plotted in various ways in order to discover the relationship that exists

Jan 1, 1943

By Fred C. Bond

The process of comminution by grinding is properly classified as an art, rather than as a science. Like most other operations concerned in ore dressing, or in the treatment of nonmetallic minerals, the mathematical relationships of rock breaking are still obscure, and much disputed. If some basic formula exists, comparable for instance to E = RI in electricity, it has not yet been placed in common use. The absence of such a comprehensive mathematical background undoubtedly is the cause of many inefficient designs and installations, as well as of much poorly oriented experimental work. On the other hand, the mathematical immaturity of the process constitutes an opportunity for a real contribution on the part of those who enjoy mental pioneering. Some of the statements made in any such exploratory work may be little more than opinions, and it is to be expected that some will later be proved untrue; but such an evolutionary development is necessary if we are ever to arrive at the fundamental laws, the discovery of which can change the empirical art into a mathematically exact science. The most significant principle of comminution that we possess is probably Rittinger's law, which states that the work done in crushing or grinding is proportional to the area of the new surface produced. There is an alternative theory, known as Kick's law, which formerly was preferred to Rittinger's but which now is rather discredited. According to Kick, the work done in comminution is proportional to the volume, or weight, of the pieces broken, or to the cube of their diameters, while according to Rittinger it is proportional to the square of the diameters. Careful determinations of size distribution below the limit of sieve sizes1 indicate strongly that under ordinary grinding conditions the amount of new surface area produced is directly proportional to the net power input. Changes in the size ratio between the balls and the particles cause important differences in the proportion of the product that passes a given mesh size, but do not affect the total amount of new surface area; they merely change the distribution of the surface among mesh sizes. The principle of constant surface area is the logical result of Rittinger's law, and it may well have an important bearing on the comminution theories of the future. Formula for Ball Wear Grinding tests have been made in the Allis-Chalmers laboratory for more than 9 years, using a standard charge of mixed balls of different sizes; and a continuous record has been kept of the rates of wear of each size. These results have been combined and plotted in various ways in order to discover the relationship that exists

Jan 1, 1943

By K. G. Davis, P. Fryzuk

VALUES for the equilibrium distribution coefficient, ko, are required for solidification studies. The procedure generally adopted1-3 is to progressively solidify alloy rods over a range of growth rates, under conditions where a high degree of convective mixing is present in the melt. The measured effective distribution coefficients are plotted as a function of growth rate, and the extrapolated value at zero growth rate is taken to be the equilibrium ko. The method is limited by the experimental difficulty in obtaining steady growth rates less than approximately 10-4 cm per sec. Extrapolation from rates greater than this can lead to inaccuracy. In the present investigation, an alternative method for determining ko, previously used by the authors for the Ag-Sn system,' was applied to alloy of thallium in tin. Specimens were grown under conditions where convective mixing was absent, and experimental concentration-distance curves in the region of the initial transient were compared with curves calculated for trial values of ko. The ko which gave the best fit was taken as the correct value. To obtain the calculated curves, a value for the diffusion constant in the liquid near to the melting point was needed. This was determined by the capillary-reservoir method. Diffusion Constants. Details of the experimental procedure used by the authors in the capillary-reservoir technique have been described in previous papers,5'6 the only variation being in the use of Tl204, a ß emitter, as tracer, in contrast to previous work where ? emitters were used. The activity of a ß-emitting sample, as measured in a Geiger counter, is proportional to the surface area. To measure the concentration of thallium along the capillary after diffusion had taken place, the solidified capillary (1 mm diam) was cut into 2.5-mm lengths and each length compressed between parallel steel plates to form a disc approximately 5 mm in diam. The discs were placed in a flat-bottomed dish, covered by a thin lead shield with a central aperture, and counted in a 0 counter with fixed geometry. Each disc was etched lightly in a dilute solution of nitric and hydrochloric acids a short time before counting, to eliminate sur-

Jan 1, 1968

As the radical element has secured control of the various local printers' unions of New- York City, 250 magazines have temporarily suspended publication rather than grant their demands. The actions of. these local unions have been repudiated by the officers of the different inter-national unions, who are seeking in every way to carry out their agree-ments with the publishers. The charters of the local pressmen's and feeders' unions have been revoked by the international officers and new local unions are being formed. Members of the typographical union are not, as yet, directly affected by the strike, but many of them are taking "vacations," which accomplishes the same purpose as the strike but without the odium. The Engineering and Mining Journal, with true engineering spirit refusing to admit insuperable obstacles, is sending out a two-page printed market bulletin, together with two typewritten pages, making an an-nouncement of its predicament and giving brief items of mining news. Thus s brought home to the members of the mining profession in a very direct way the pernicious results of unrestrained control of labor organi-zations-by foreign and un-American elements. No sermon on this sub-ject is required, as the facts themselves are sufficiently eloquent.

Jan 11, 1919

By Don M. Jackson

The techniques for the growth and controlled, graded doping of silicon epitaxial overgrowth layers were established. Grading of- impurities such as arsenic or boron in arbitrarily chosen profiles oiler four orders of magnitude (from I X 10Lg to 1 X 10L5 cm) was accomplished. The graded structures were grown in a stepwise manner where in the profiles were approximated by growing many separate layers with small doping-level changes between layers. Masked-area growth of silicon through windows in a SiO2 masking film was acconiplished through the simultaneous injection of HCl gas 102th Sic14 in the epitaxial reactor. The HCl served to inhihit the growth of silicon on the Sz02 surface, and also to control the cross-sectional profile of the silicon mesas. silicon from the substrate was etched out through the windows, and then epitaxial material was used to fill the holes hack in to form planar diodes. Simullaneous HCl injection was adapted to control the cross-section profile of the hack-filled regions. Arsenic-huried regions beneath in te- In recent months, the epitaxial growth process in semiconductor materials technology has evolved into a complex system directed at both material improvement for better monolithic integrated-circuit characteristics and the development of new silicon structures for future integrated-circuit needs. The advent of high-temperature HC1 gas etching1 grated-circuit transistors reduced V(SAT) by slightly more than one third, bringing this parame-ter to that of an isolated component transistor. When arsenic was diffused into the starting sub-stvate, it was necessary to remove any excess arsenic in order to avoid excessive audodoping of the subsequent epitaxial layer. Oxide isolation of single-crystal regions in a substrate provided complete electrical isolation of integrated-circuit components, thereby eliminating parasitic capacitance which is inherent in standard integrated-circuit processing. The process involved the etching of deep mesas on silicon Wafers, the formation of an oxide over the mesa surface, and then the deposition of several mils of polycrystalline silicon over the oxide. The original substrate was lapped and polished allay until the mesas were left isolated in the polycrys-talline matrix. The Final components were fabri-cated in the single-crystal islands. Speed and power-handling capabilities of standard circuits were improved through the process. wherein work-damaged material is removed from the surface of the silicon wafer just prior to the silicon deposition step has made it possible to grow silicon films with structural quality that approaches that of the substrate. HBr used in the same volume ratio as HC1 etches silicon at the same rate and with the same results as HC1. Recent developments in epitaxial materials technology have occurred in the areas of precise doping control, buried prediffused regions between over-

Jan 1, 1965