Search Documents

By Carl F. Cline, Richard R. Vandervoort, Willis L. Barmore

THE objective of this investigation was to determine the high-temperature plastic deformation behavior of stoichiometric uranium mononitride as a function of stress and temperature. Interest in the properties of this material stems from its potential use in high-temperature nuclear reactor systems. The creep of other refractory compounds containing uranium (e.g., U02, UC) has been studied by various investigators.1"4 Fassler et al.4 have studied the creep of UN in vacuum from 1100° to 1350°C at stresses of 6000 and 8000 psi. In the present work, the creep of stoichiometric UN was investigated from 1500° to 1800°C at stresses from 2000 to 5000 psi in a partial pressure of 200 mm of nitrogen. The specimens were prepared by hot isostatic pressing of UN powder into cylinders of $ in. diam by about 1 in. high. After pressing, the specimens were heat-treated in nitrogen at 1900°C for 50 hr. The densities of individual specimens were determined by the water displacement method. All specimens were theoretically dense, based on a value of 14.32 g per cu cm.5 Principal metallic impurities in ppm by weight were: Ca, 50; Cu, 5; Fe, 30; Mg, 5; Ni, 10; and Si, 20. Oxygen content was 400 ± 50 pprn and carbon content was 100 i25 ppm. The nitrogen content was 5.56 ±0.05 wt pct. The average grain size for five specimens, as determined by the intercept method, was 0.14 i 0.01 mm. One specimen had a grain size of 2.0 mm. This large grain size is an anomaly, since all specimens had the same chemical and thermal histories. Specimens of 1/4 in. diam by 1/2 in. high were creep-tested in compression in a clam shell furnace heated by W-25 pct Re sheet elements. Temperature was measured to ilODC by an optical pyrometer which had been calibrated by a standard source. The distance between fiducial marks on the specimen was measured before placement into the furnace. The furnace chamber was evacuated to 10-5 Torr and back-filled to 200 mm N2. After heating rapidly to temperature, the load was applied and controlled to ±2 pct by an Instron testing machine. Upon initial loading, the specimen was deformed until a constant crosshead rate was obtained, then quenched to room temperature, remeasured, and replaced in the furnace. Upon subsequent reloading at temperature, the crosshead rate was constant for the selected condition indicating steady-state creep.

Jan 1, 1969

By William Metcalf

It is the object of this paper to oppose unnecessary changes, and the introduction of new and confusing terms. From the earliest times of which we have ally record on the subject, iron has been divided into general classes. Whether iron was first known in the form of wrought iron or of steel, is a matter of no importance; but at the time when cast iron first became a prominent article of commerce, wrought iron and steel were old products— steel, at that time, being generally made from wrought iron by the process of cementation. As steel was then properly defined as iron containing more carbon than wrought iron, so cast iron was appropriately defined as iron containing more carbon than steel. Until the year 1776, when Huntsman first began the manufacture of a new kind of iron by melting wrought iron and steel in crucibles, the above definitions were all that could be desired. At first, probably, owing to imperfect appliances, only a highly carburized iron was melted in crucibles, and this led to its being called cast steel. If our ancestors had found a name for this material not involving the use of the word steel, we would have been saved the trouble of the present discussion. As the arts developed, new uses were found for steel, and the products of the crucible were varied, until at the present day it is quite common to find steel containing no more carbon than average wrought iron, and other steel containing nearly or quite as much carbon as some cast iron. All of these various products of the crucible have retained, or received, the name cast steel, usually abbreviated to the simple word steel, without caus-ing any confusion among producers or consumers in regard to terms or their meaning. In 1865, twenty-one years ago, the Bessemer process was introduced ; this was followed in a few years by the Siemens-Martin process, and the products of both were at once, and have ever since been, called steel, from the fact that they were identical in chemical and physical properties with crucible cast steel. At the present time, then, we have three subdivisions of cast steel, viz.: Crucible cast steel, Bessemer cast steel, and Siemens-Martin,

By A. Eilers

THE telluride of gold and silver, the " Tellurgold-silver" of Hausmann, and " Petzite" of other mineralogists, has been found in so few localities, that a late discovery of the mineral in a new locality may not be uninteresting. So far this mineral has been found in Europe only in a few mines in Transylvania, and in Hungary ; and in the United States in the Stanislaus Mine, in Calaveras County, California, in the Golden Rule Mine, Tuolumne County, California, and in a mine in Montana, the precise locality of which I have forgotten. The new locality referred to is at the Red Cloud Mine, Gold Hill District, Boulder County, Colorado.

Jan 1, 1873

By S. J. M. van Leeuwen, R. Feenstra

The effect of jets on bit penetration has been investigated by means of a 50-ton drilling machine and 8½-in. commercial jet bits, drilling under representative bottom-hole conditions. The conclusions apply to the drilling of impermeable rock only. Penetration rate is in all cases primarily hampered by a differential pressure effect, known as dynamic hold-down. Jet action can reduce this slightly. Major gain in penetration rate, up to 25 or 50 per cent, is already ohtained at medium-high jet power. At high bit load, penetration by soft to medium-hard-formation bits is further hampered by bit-balling. Its alleviation requires intensive tooth scavenging, which is best performed by slanted nozzles with trailing, high-velocity, high-volume jets, hitting bottom in front of the teeth. Penetration may then improve by a 100 per cent. At high bit load, bottom-balling limits the penetration of insert-type bits. In this case bottom scavenging is required, which is most effectively performed with high velocity jets from nozzles extended close to bottom. As a result of this measure, penetration may improve 70 per cent in non-friable rock, and less in friable rock. This will make the insert-type bit more versatile. Toothed hard-formation hits suffer at high bit load from both bit- and bottom-balling. Slanted nozzles, possibly much extended, with high-velocity, high-volume jets then have best prospects. INTRODUCTION For years the use of jet bits in oil well drilling has been increasing, in conjunction with ever greater hydraulic horsepower. To the same extent, the need for efficient use of the horsepower has grown.' This paper, it is hoped, will contribute to an understanding of how effective jet action may be obtained. It deals with the effect of jets on phenomena that are known' " to hamper bit penetration. To study this effect, laboratory drilling tests were performed with 8½-in. commercial bits under bottom-hole pressures representative of deep wells. The investigation has been restricted to the drilling of practically impermeable rock. In the following sections, the increase in bit penetration rates due to jetting is discussed for conditions which made the troublesome phenomena stand out one at a time. A brief definition and interpretation of these phenomena is given in Appendix A. Appendix B gives the results of measurements of fluid velocities along the hole bottom, performed in stationary flow tests. Descriptions of equipment, bits, rocks and mud are collected in Appendix C. Unless otherwise mentioned, drilling conditions were kept standard as given in Table 1. CUTTING TRANSPORT TO THE ANNULUS Jet action was for some time believed to merely improve the transport of cuttings from bottom to annulus, resulting in a clean hole bottom. Flow tests performed in 1954 at the Battelle Memorial Institute6 showed, however, that jet velocities of the order of 40 ft/sec sufficed to clear even large (0.4-in.) chips from bottom in the time between two successive tooth actions. In the field, optimum jet velocities are appreciably higher, indicating that other effects must be involved. This much is confirmed by the results of our drilling experiments in soft rocks performed under atmospheric pressure, i.e., in absence of pressure-differential effects. Fig. 1 shows that variation in the nozzle velocity from 40 to 330 ft/sec had no effect on penetration rate, unless the bit penetrated more than 7 mm per revolution, which is about half the tooth height. At such high rates—150 ft/hr at 100 rpm—cuttings would be caught in the tooth cavities, leading to bit-balling, which was noticed on inspection of the bit. The jets thus assisted in keeping the tooth cavities clean. This is just perceptibly reflected in the penetration-rate curves of Fig. 1: Much the same results were obtained in hard rocks with hard-formation three-cone bits. The conclusion is that transport of loose cuttings towards the annulus does not require a powerful jet action. In the following sections we shall see that in deep-well drilling other phenomena are of greater importance. DYNAMIC HOLD-DOWN It is generally accepted that, in deep-well drilling, bit penetration is hampered primarily by the existence of a difference in pressure between the fluid in the hole and that in the rock at the depth of cutting.2-5 In the drilling

Jan 1, 1965

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input—heat enerb output) used in creating new surface, gliding or slip on atomic planes, twinning, and possibly other lattice rearrangements within the mineral. If it be postulated further that with a hard, brittle crystalline material, such as quartz, the energy used to produce gliding, twinning, and other permanent lattice movements is a very small fraction of the total net energy absorbed, then this energy absorption within the grinding calorimeter can be ascribed to the creation of new surface energy alone. Such energy is, from the thermody-namic standpoint, the true effective work of the grinding device, in this case a tumbling-medium mill. The ratio of this effective work (in calories) to the total energy input (in calories) should express the thermodynamic efficiency of the comminution taking place under the conditions used in the grinding calorimeter. This approach to the measurement of the energetics of tumbling-mill grinding was suggested by some previous work by Fahrenwald and coworkers' with a laboratory ball mill and a thermometer. They measured the efficiency of grinding based on the formula: Pct Grinding Efficiency = Energy (calories) — Thermal Energy x 100 1npZ Output (calories) Energy input (calories) Efficiencies thus measured, while grinding quartz sand, ranged from 19.7 pct to 7.4 pct. Cook in 1915,' used this approach to the problem of grinding efficiencies in stamp batteries and obtained the energy input by stamp weights times drop distances and the energy output by means of thermometers and pulp flow rates. He calculated that 80 pct of the input energy to the stamp shoes was wasted as sensible heat in the ore pulp. No other studies of comminution by this method of energy differences came to the author's attention. Reasonable agreement as to the order-of-mag-nitude of comminution efficiencies in tumbling-media mills is lacking in the literature. There is a widespread impression among technical workers that the grinding efficiency of the industrial ball mill may be on the order of 1 pct, or even a fraction

Jan 1, 1952

By James A. Beck

Phosphorus is essential to all life processes and therefore to the existence of man. In this role, there are no substitutes for phosphorus. In a commercial sense, phosphorus and its compounds are important to our entire economy, both in agricultural and in nonagricultural applications. The world's phosphate requirements are met by mining phosphate rock. Two general types of phosphate ore deposits are commercially important-igneous and sedimentary. Igneous deposits generally are more difficult and more expensive to mine than sedimentary deposits and are of importance mainly in the USSR, North Vietnam, and South Africa. Approximately 15% of current world production comes from these deposits. Over 80% of world production is from the pellet sedimentary deposits of Florida, North Africa, and elsewhere. Guano, the second type of sedimentary deposit, is produced in South America but is declining in world importance. Production Production of phosphate rock was reported in 31 countries during 1972. However, about 80% of world output is produced in three countries: the United States, the USSR, and Morocco (Table 15.2A.1). Throughout the past 20 years, between 75% and 80% of world output has been produced by these three leading countries. Between 1948 and 1972 world production increased at an average rate of 10% per year, from 21.5 to 103.9 million tons. Growth was quite steady at 6% per year through 1963, but in the 5 years from 1963 to 1968 production increased 11 1/2% per year. Since 1968 production has increased about 91/2 % annually. Since 1948 several new phosphate mining ventures have been developed in Senegal, Togo, Israel, and North Vietnam. In the same period, only one important phosphate deposit, on Makatea Island, has been mined out and closed. A number of other phosphate mining ventures are in various stages of planning and development. The most important new venture in phosphate mining is in the Spanish Sahara. New mining capacity is expected also in Syria, and serious investigation is in progress in Peru, India, Turkey, and Australia. Major expansion of existing operations is expected in Morocco, Russia, Tunisia, Israel, and Jordan. Consumption Historical data on world consumption of phosphate rock are not available in detail, but world consumption of phosphate has closely paralleled world production in the past two decades. The United States is the world's largest user of phosphate rock, accounting for 30%

Jan 1, 1976

By James A. McGurty, Walter J. Koshuba, Samuel G. Gordon, Gilbert E. Klein

ONE of the problems encountered in working with metals at elevated temperatures is the instability resulting from solid-solid diffusion at a -common interface. A determination of the nature and magnitude of this phenomenon is important as related to structural properties of materials potentially useful in high temperature applications. This paper is concerned with the solid state reaction between metallic molybdenum and beryllium at elevated temperatures. In the older literature,' there were no known inter-metallic compounds in the system Be-Mo, and the list of beryllium intermetallics was rather small. New compilations have been made by Smithells' and by Taylor," listing all the then known beryllium binary intermetallic compounds. In addition to these, some new phases have just been reported' in the system Zr-Be and some further compounds of the type MBe,3 have been currently described. The new compound MoBe,, which is reported upon in this paper differs considerably from the above mentioned MBe13 group, and will be discussed in detail. Diffusion Study The nature of the solid diffusion at a Mo-Be interface was determined by sealing a beryllium rod inside a molybdenum capsule and heating at a temperature of 2000°F' (1100°C) for 100 hr. The molybdenum capsule was fabricated from % in. swaged molybdenum rod obtained from the Fansteel Metallurgical Corp. The beryllium metal was obtained from Brush Beryllium Corp. as % in. cold-drawn rod. This material assayed 99.05 pct Be and contained as impurities 0.84 pct Be0 and 0.19 pct Be2C. The molybdenum capsule was % in. in OD x 2 in. long. To prepare it, a concentric hole 0.250 in. + 0.001 in. — 0.000 in. in diam was drilled and reamed in one end of a rod to a depth of 1 '/2 in. A 1 in. long beryllium rod 0.250 in. + 0.000 in. — 0.001 in. in diam was pressed into the molybdenum capsule. A molybdenum plug 0.250 in. & 0.001 in. in diam x 9/16 in. long was then used to seal the beryllium in place. The capsules were placed in a molybdenum resistance furnace and heated at 2000°F (1100°C) for 100 hr. On cooling, the specimens were cut and examined metallographically. Fig. 1 is a micrograph at X250 of a portion of the interface from a transverse section. Four phases are clearly visible, with sharp boundaries between them. Phase A is a section of the molybdenum capsule; phase B is the molybdenum-rich intermetallic composition MoBe,; phase C is the beryllium-rich compound MoBe13; phase D is a section of the beryllium rod. All phases were readily polished to a high metallic luster. The molybdenum-rich phase has a pronounced purple tinge. The beryllium-rich phase (C) is only slightly darker than the pure beryllium. In polarized reflected light, however, it shows striking birefringence between crossed Nicols. The black areas represent flaws or pores in the material. A small representative amount of powdered material from each of the phases was carefully removed under the microscope with a diamond tool. With this material, powder X-ray diffraction patterns were made for the identification of each phase. Table I lists the X-ray diffraction spacings and corresponding indexes characteristic of these intermetallic compounds. Synthesis To establish the formula of the new intermetallic compound, X-ray diffraction patterns were made from powders obtained from solidified melts of known composition. The syntheses were made by

Jan 1, 1952

By M. Baeyertr

Since 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallogmphy. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types. Radiography Radiography is the field in which the application of X-rays has had most general appeal among the industries which produce or use metals and alloys. Equipment permitting the examination of heavy sections of metals less permeable than aluminum or other light alloys requires apparatus capable of generating hard X-rays over a considerable period of time. The equipment used in the work presented in this paper is practically identical with that described by Fink and Archer in their paper on radiography in industry and is easily capable of penetrating 1/8 in. of lead. Radiography is used in two major groups of problems: (1) in the development of cquipment and tools and (2) in studies of materials. So far there has been no instance in which the use of radiography for routine inspection is justified. This is partly due to the fact that the manufacture of telephone apparatus involves the production of many identical parts by standardized procedures and equipment that has had development and trial before being put on a regular production basis. It is during this stage of development of equipment and tools that radiography has been used to particular advantage.

Jan 1, 1931

By Sid T. Killan

The utilization of the reducing power of blast-furnace gas can be estimated by applying two rectifying calculations to the gas analysis. A resulting corrected CO/CO2 ratio varies inversely with furnace production. Directions for calculating the corrected CO/CO2 ratio are given, and a corrected CO/CO2 ratio is compared with actual furnace production. THE inadequacy of the normally accepted CO/CO, ratio as a measure of blast-furnace performance and furnace efficiency was discussed following the presentation of the paper by H. F. Dobscha.' In this outstanding example of careful observation on large scale blast-furnace operation, the changes occurring with beneficiated ores were: 1—A net gain in tonnage of 21.2 pct. 2—A decrease in net coke of 15.3 pct. 3—A decrease of 1.9 pct in the CO/CO, ratio. In this great change in furnace performance, the CO/CO, ratio proved itself worthless. The discussion of the inadequacy of expressing furnace performance and efficiency by the CO/CO, ratio led indirectly to the calculations forming the basis of this paper. At that time Dr. T. L. Joseph said: "We must consider difference in CO, from the stone in the two cases when we talk about the ratios of CO/C02." This statement is used for the second of the two CO/CO, ratio corrections forming the basis of this paper. The research work in attempting to find out why the furnaces could op-erate so differently with practically the same CO/CO, ratio lead not to the answer sought but, after a shift to the gaseous phase in the research work, the proof that the normal CO/ CO, ratio was outmoded and a new corrected ratio should replace it. To be of any value, any new corrected ratio should express approximate furnace efficiency and give an idea of practical furnace performance to be expected. This the normal CO/CO, ratio has failed to do. However, in the absence of anything better, some credence has been attached to the normal CO/CO, ratio. As far as the writer can ascertain, the present paper is the first attempt to change or improve the normally accepted index of

Jan 1, 1952

By M. A. Quader, D. Kuhlmann-Wilsdorf, R. A. Dodd

STACKING fault tetrahedra were first observed in quenched and aged pure gold by Silcox and Hirsch1 and identified as defects originating in the collapse of vacancy discs on {111} planes. It was supposed that sessile loops are the first product of the collapse, and that by a dislocation dissociation/glide sequence these are converted into tetrahedra. Although the tetrahedra can be mechanistically accounted for in this way, recent investigations indicate that their growth occurs by the absorption of individual vacancies on small nuclei involving perhaps as few as six vacancies.2-7 Besides stacking fault tetrahedra, triangular and crystallographic shaped Frank loops, although fewer in number, have always been observed in quenched and aged gold.19798 It is not known definitely whether these loops form from collapsed tetrahedra. The fact that the Frank loops are usually larger than the accompanying tetrahedra might indicate that the loops grow independently by absorbing vacancies, but this does not rule out the possibility of the collapse of tetrahedra into loops under all circumstances. Silcox and Hirsch1 have actually observed under the electron microscope tetrahedra collapsing into loops, probably due to stresses set up by the heating of the specimen by the electron beam. The energy residing in the stacking faults of a tetrahedron is proportional to the square of the edge length, while the energy of a triangular perfect dislocation loop depends on its edge length, L, as const L ln(L/ro). Therefore, beyond some critical size tetrahedra must become unstable with respect to collapse into triangular loops.1,3,8-11 However, it seems that in the absence of strong stresses tetrahedra usually decay by the

Jan 1, 1969

By J. H. Bechtold, R. Kossowsky

1 HE superplastic behavior of the eutectoid A1-78 wt pct Zn alloy has been thoroughly investigated by Back-ofen et al.' The superplastic elongations and the marked resistance to necking were rationalized in terms of high strain rate sensitivity. In a subsequent paper2 superplastic behavior was formulated to show Nabarro-Herring diffusional creep as rate controlling at low strain rates, giving way to a dislocation climb process at higher strain rates. In a paper devoted to an interpretation of superplasticity in two-phase alloys, Packer and sherby3 have included the results of an examination of the structure of an Al-Zn eutectoid specimen before and after superplastic deformation. No significant change in grain size or directionality was observed in the deformed microstructures. This one observation led the authors3 to suggest that con- tinuous recrystallization or grain boundary migration was responsible for superplasticity. The purpose of this note is to report our observations on the superplastic behavior of the Al-Zn eutectoid alloy which differ in certain respects from works previously reported. Following Hayden et al., the results are discussed in terms of dislocation climb as the important factor during superplastic deformation. A heat of nominally high (99.995) purity 22 wt pct A1-78 wt pct Zn was induction-melted and cast into a 0.5 by 6 by 12 in. slab. The slab was heated to 350°C and rolled to 1/8-in.-thick plate. The plate was then cold-rolled to 0.040-in. thickness, annealed at 35OaC, and rolled to the final thickness of 0.020 in.* Speci-

Jan 1, 1969

By M. A. Hosmer, Job Goostray, R. F. Harringon

In this paper, as in so many discussions of an historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but they cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from Mackintosh-Hemp-hill Co. (formerly the Fort Pitt Works) and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dickson of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I. Three Epochs in History of Cannon Among the great industries of New England, the manufacture of iron was the first to receive attention. Iron ore in considerable quantities was known to exist within the territory of the Massachusetts Bay Colony; and as early as 1629 some steps appear to have been taken toward the manufacture of iron by the Court of Assistants in London, under whose patronage the colony was founded. During the next ten years, deposits of bog ore were found in numerous ponds in the Plymouth Colony; and, in 1652, iron manufacture was begun at Raynham. The "Old Colony" was known as the main seat of this industry in New England, out of which grew a concern which was later to become one of the principal

Jan 1, 1925

Victor G. Hills, Cripple Creek, Colo. (communication to the Secretary): In continuation of the subject of the perform ance of "baby machine-drills," presented by Mr. Thane, I sub mit the following records of work done with these drills in the Cripple Creek district of Colorado. Two years ago, the Anchoria-Leland mine began to use baby drills ; and, to make the experiment more complete, began by purchasing two machines, of the same size, but of different make. The little drills were first used for stoping and up raising, in which they achieved at once an unqualified success. Soon after, they began to be used for the smaller branch-drifts and prospecting cross-cuts, while the large two-man drills were still used for the main drifts. Now they have almost entirely superseded the large drills, since it has been found that they will do any ordinary work in the mine at less cost, both for labor and for powder, per ton of rock broken. The large drills, of course, make more rapid progress; but it is only where time is a specially important factor that they are now used. The Portland mine, where, until within a year, only the large machines were used, is now using some small drills for stoping, and also for drifting. Mr. Thane speaks of having two men to operate a baby-drill; but in this district the baby-machine is always worked by one man without help. Again, in Prof. Christy's postscript, the quoted extract from a letter of Mr. L. T. Seymour, the South African engineer, mentions a " 2 1/2-inch Little Giant," as though that were the smallest machine used in that region. These statements leave some doubt as to just what Mr. Thane means by a " baby-drill." To avoid any such uncertainty as to the present communication, I will say that the large or two-man drill in common use at Cripple Creek has a 3 1/8-inch cylinder; while a few mines employ a 3-inch, and a few, in running large tunnels, a 3 1/2-inch drill. What we call a baby-drill here has a

Jan 1, 1900

By J. T. Crawford

THE purpose of this paper is to present some data and comparisons regarding three types of Rheolaveur plants washing bituminous coal from the Pittsburgh seam. It deals only with the sections that handle coarse coal. The Rheolaveur system consists of launders or troughs in which coal and its associated impurities are conveyed by water. The impurities, being heavier than the coal, settle toward the bottoms of the launders and are drawn off through specially designed openings called Rheo boxes. Fundamentally, each plant consists of straight-sided, flat-bottomed launders of varying width and length, each launder equipped with one or more Rheo boxes for the removal of high-gravity fractions of the feed that are undesirable in the cleaned coal. Each launder has at least two longitudinal sections, the first with a slope of from 1 1/2 to 4 in. per foot of length, called the classification section. The single-box launder has a classification section followed by a washing section ahead of the box. A two-box launder is a single-box launder followed by a washing section and a second box. The slope of the washing section between the first and second boxes is determined to some extent by tonnage. At the end of the classification section, which may vary from 8 to 15 ft. in length, the slope abruptly flattens out to a slope of from ½ to 1 in. per foot of length. This flatter section of the launder, called the washing section, may vary from a few feet, in a single-box launder, to 15 ft., in a two-box launder.

Jan 1, 1938

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company's well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company's well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By M. G. F. Sohnlein

IN a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. +20 8.0 +40 36.5 +60 9.0 +80 10.5 +100 5.5 +150 4.51 -150 25.0 99.0 Loss 1.0 IN the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.1 This remodeled classifier consists of a truncated pyramidal wooden hooper A with an attachment of cast iron

Jan 4, 1916

By E. D. Slone, F. L. Dillard

When a new mine is in the planning stages, one of the most important decisions to be made is the selection of' face haulage equipment and the interrelated transportation system to the surface. Equally important is the method of transporting personnel supplies and repair parts from the surface to the working places. When Bell & Zoller management elected to open the new Zeigler mine in the No. 9 seam near Madisonville, Ky., last year, various transportation systems were considered. It was agreed early that a slope mine would be preferred to a shaft mine, and that belt conveyors would be more economical than a rail system.

Jan 1, 1970

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman A. D. BEERS, Secretary, 55 Wall St., New York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. W. E. C. EUSTIS, Chairman. R. L. AGASSIZ, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, -Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K: ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 7, 1916

By Otto C. Kopp, Thomas B. Crattie, Dennis R. Owen

Whole-rock analyses of limestones, fine-gralned dolostones and coarser-grained dolostones adjacent to mineralized breccias (Coy mine, Mascot-Jefferson City district) were compared with similar lithologies adjacent to apparently non-mineralized breccias at the new Thorn Hill section located approximately 39 km north of the Coy mine. Specimens were analyzed for Ca, Mg, Si, Al, K, Fe, Mn, Sr, Br, C1, S, Ti and P using X-ray fluorescence analysis. The concentrations of the major and most minor elements for Thorn Hill specimens fall within the range of concentrations for Coy mine specimens; however, significant differences (probability < 0.05) were noted for Fe, C1 and Br for fine-grained dolostones and for MgO, Fe and Mn for the coarser-grained dolostones. No significant differences were detected for the limestones.

Jan 1, 1985