Search Documents

By J. P. Zannaras

If we assume that testing of the model started at time C, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. 1), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t, after time t, motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made.

Dec 1, 1956

By Norman P. Goss

The Chairman.—Thank YOU, Mr. Goss Gentlemen, I believe we have heard one of the finest papers, especially since Mr. Goss has been very generous in his frank discussion of continuous casting. One point he has brought out which 1 think some of us have not thought through to the same extent that he has—that the continuous casting process offers the small producer an opportunity to compete with the larger, more conventional and presumably better established industries. The meeting is now open for discussion. Are there any questions concerning the first two papers? J. A. Malone.*—I should like to ask Mr. Goss whether there is any special problem involved in the first part, the upper part of the mold before he gets to the first graphite lubricant area. N. P. Goss.—You mean in the forming chamber where chilling first takes place? J. A. Malone.—Yes. N. P. Goss.—So far I have not had any trouble in this part of the setup. My only

Jan 1, 1945

By T. M. Olson, B. G. Lewis

The adsorption of selenite on bentonite, kaolinite, and an iron--coated illite was studied to determine the importance of several soil variables on selenite removal from uranium mill tailings pond seepage. Adsorption capacities of the clays of selenite varied by orders of magnitude and decreased in the following order: illite > kaolinite > bentonite. Maximum adsorption of selenite on the clays was observed between pH 2.5 and the clay's zero-point-of-charge. Substantially less selenite was adsorbed on these clays in actual mill tailings solutions than in model systems. Virtually all selenite was removed from the tailings at pH 7. The principal removal mechanism at this pH is suggested to be the adsorption of selenite on freshly precipitated metal hydroxides. It is concluded that selenite can be removed from tailings seepage in soil or in clay liners in the presence of kaolinitic clays and iron oxides. Selenite would also tend to be removed from tailings seepage in calcareous strata.

Jan 1, 1984

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

By Herbert Clark Hoover, Lou Henry Hoover

We give the following brief notes on early works containing some reference to mineralogy, mining, or metallurgy, to indicate the literature available to Agricola and for historical notes bearing upon the subject. References to these works in the footnotes may be most easily consulted through the personal index. GREEK AUTHORS.-Only a very limited Greek literature upon subjects allied to mining or natural science survives. The whole of the material of technical interest could be , reproduced on less than twenty of these pages. Those of most importance are : Aristotle (384-322 B.c.), Theophrastus (371-288 B.c.), Diodorus Siculus (1st Century B.c.), Strabo (64 B.c.-25 A.D.), and Dioscorides (1st Century A.D.). Aristotle, apart from occasional mineralogical or metallurgical references in De Mirabilibus, is mostly of interest as the author of the Peripatetic theory of the elements and the relation of these to the origin of stones and metals. Agricola was, to a considerable measure, a follower of this school, and their views colour much of his writings. We, however, discuss elsewhere1 at what point he departed from them. Especially in De Ortu ct Causis does he quote largely from Aristotle&apos;s Meteorologica. Physica, and De Coelo on these subjects. There is a spurious work on stones attributed to Aristotle of some interest to mineralogists. It was probably the work of some Arab early in the Middle Ages.[ ]

Jan 1, 1950

By Vincent P. Gianella

THE most intense earthquake on the Pacific coast in the last several years, and probably the second most intense shock to occur in Nevada since it was settled, was felt in many Western States shortly after 10 p.m. on Dec. 20, 1932. Be- cause the rifted area contered about the northern end of Cedar Mountain it is referred to as the Cedar Mountain, Nevada, earthquake. An idea of the intensity of the shock may be gathered from the distance at which it was felt: in Wyoming, Utah, Idaho, Nevada, Washing- ton, Oregon, California and Arizona. It is the strongest quake centering in Nevada since the Pleasant Valley earthquake on Oct. 2, 1915. Despite the strength of the vibrations and the large area over which they were felt, relatively little damage was done. The extent of the damage consisted of a few old stone buildings demolished as shown in Fig. 1, much cracked and fallen plaster, many chimneys shaken down and considerable cracking of brick walls. There were no deaths and four people were but slightly injured. The small amount of damage was due, largely, to the scarcity of structures within the area of strong vibrations, but an important factor was the aridity of the region (see Fig. 2) and the shallowness of soil cover so that there was but little water-saturated loose material in which strong secondary vibrations could be formed. Had this earthquake occurred in a region of heavy precipitation and dense population the damage to property and loss of life would undoubtedly have been large, with consequently much more newspaper publicity.

Jan 1, 1933

The first record of coal anywhere in the Appalachian regions of which we now know is along the north fork of the Potomac River, above the mouth of Savage River, on a map entitled, A Plan of the upper Part of Potomack River call Cohongorooto Survey&apos;d in the Year 1736. Benj. Winslow1 two "Cole-mines" are shown, one just above Green Island and the other just below Hopwood Run. Winslow was in charge of a surveying party to "Lay out the Bounds of the Northern Neck of Virginia," or Lord Fairfax&apos;s Grant, his party locating the liver above the mouth of the Shenandoah, while another party located it below that point, and then around Chesapeake Bay and up the Rappahannock River. The results of the two surveys were combined in a map called, The Courses of the Rivers Rappahannock and Potowmack, in Virginia, as surveyed according to Order in the Years 1736 & 1737, made by Wm. Mayo, which does not show the "cole-mines;" this map was used with the report of the boundary commission which was sent to London in the case before the Privy Council. The boundary line decided upon was surveyed on the ground in 1746, just ten years after the original one. The results of this work were shown on A Map of the Northern Neck in Virginia, According to an Actual Survey begun in the Year MDCCXXXVI, and ended in the Year MDCCXLVI, Drawn by Peter Jefferson And Robert Brooke, Surveyors, which is now in the Colonial Office in London. This map shows the "cole-mines" in the same location as on Winslow&apos;s map, and taken from his record, of course, as that part of the survey was not retraced. Faulkner, who examined all of these records in his review of the case in 1832, refers to the notes of the original survey as "No. 10. The original field notes of the survey of the Potomac River, and the mouth of the Shenandoah to the head spring of said Poto¬mac River, by Mr. Benjamin Winslow." While the notes of the 1746 survey are in the London records and photographic copies of them are in several libraries in this county, the notes of the 1736 survey cannot be found anywhere. (For Chas. J. Faulkner&apos;s report, dated Nov. 6, 1832, see Kercheval&apos;s History of the Valley of Virginia, pp. 160-173. Jas. W. Foster&apos;s Maps of the First Survey of the Potomac River, 1736-37, in Wm. and Mary College Quarterly History Mag., April, 1938, gives a complete history

Jan 1, 1942

By R. H. Tien

This paper presents an analytical solution of the problem of freezing of a semi-infinite slab with constant surface temperature; in this analysis accoz~nt is taken of the heat evolution during the solid-state transformations in the frozen skin. The regions where transformations occur are treated as plane isothermal heat sources; i.e., the rates of transformations are assumed to be infinite. In the model considered, three plane heat sources are assumed to be present in the frozen solid. The solution yields the temperature distribution in the solid, the rates of movement of the heat sources , and the rate of movement of the solidification front. It is shown that, although the sum of the heats of transformations in the solid is about 20 or 43 pct of the heat of fusion of iron or manganese, respectively, the effect of the heat evolution in solid-state transformations on the rate of solidification is insignzficant. IN several recent mathematical studies of solidification of liquid metals&apos;-3 no account was taken of the heat evolution accompanying the solid-state transformations. In the case of, for example, steel, there are several phase transformations 6 -y, y -a, and the magnetic transformation. Whether or not a significant error is introduced into the mathematical simulation of solidification processes by the omission of the heat effects associated with these phase transformations is not known. The purpose of the present study is to investigate the effect of these phase transformations on the temperature distribution and the rate of solidification based solely on the heat transfer point of view. That is, for the sake of simplicity, freezing of a pure metal with solid-state transformations will be considered. The mathematical model which represents the present problem includes four moving heat sources representing freezing and phase transformations, 6— y — a — ferromagnetic. The thermal properties such as conductivity and specific heat, and so forth, are different from one phase to the other. But they are considered to be uniform over any particular phase. The usual Fourier heat flow law is employed. The concept of conservation of energy is applied at every heat source in order to estimate their rate of movement. The temperature distribution in the solid and the positions where transformations occur are expressed analytically in terms of error function solutions and four coefficients which are determined from four nonlinear algebraic equations. These coefficients can be calculated either by trial and error or by any numerical method. MATHEMATICAL ANALYSIS Fig. 1 is a schematic diagram showing the zones of different phases 1, 2, 3, and 4 in the solidified portion of a semi-infinite pure liquid metal. The heat is subtracted from the system at x = 0 which is maintained

Jan 1, 1968

By A. S. Grove, C. T. Sah, E. H. Snow, B. E. Deal

A summary of- several recent investigations in to the properties of the metal-oxide-silicon system is presented. A major portion of these studies makes use of the MOS capacitance-z)oltage method of&apos; analysis. The particular areas of investigation which are reported include: 1) a general survey of the electvical properties of thermally oxidized silicon surjbccs; 2) a study of ion migration through silicon dioxide films ; 3) measurements of electron and hole mobilities in surface inversion layers; 4) a study of impurity redistribution due to thermal o.ridatiotz; and 5) measurements of the rates of oxidation oj-heavily doper7. silicon. THE importance of the metal-oxide-semiconductor (MOS) system in the semiconductor industry is well-known. In addition to its importance in the "planar" device technology,&apos; the MOS structure is now also used in the fabrication of active solid-state devices. Consequently, extensive efforts have been made recently to obtain a better understanding of the characteristics of this system. A summary of some studies of the MOS system conducted in our laboratories during the past year is presented. For the most part these studies used silicon as the semiconductor, along with silicon dioxide and aluminum as the other two components of the system. Since the MOS capacitance-voltage method of analysis was used extensively in these studies, we will first briefly describe its nature and consider some of the possible causes of deviation of experimental observations from the simple theory. We will then outline the various related areas of investigation carried out in our laboratories and will briefly indicate some of the results. It should be noted that the purpose of this paper is merely to provide a brief summary of MOS studies. More detailed discussions of the various areas of investigation are given in the references cited. PRINCIPLES OF THE MOS C-V METHOD OF ANALYSIS&apos; A sketch of the MOS structure is shown in the upper portion of Fig. 1. In this case the insulating film is Si02 and the semiconductor p-type silicon. If a large negative bias is applied to the metal field plate, holes are attracted to the silicon surface. The silicon then behaves much like a metal and the capacitance measured is that of the oxide layer alone, Co. If a small positive bias is applied to the aluminum, holes are repelled and a region depleted of majority carriers is formed at the silicon surface. This depletion I-egion adds to the width of the dielectric and the measured capacitance begins to drop. With increasing positive bias, the width of the electrical depletion region increases. At some large positive bias an inzevsion regiotr is formed at the surface and additional charges induced in the silicon appear in the form of electrons in this narrow inversion region. Thus the depletion-region width approaches a maximum value and, consequently, the capacitance reaches a minimum value and then either levels off or rises again depending on the measurement frequency and the rate of equilibration of the minority carriers in the inversion layer.3 Band diagrams, along with the corresponding charge distributions, are shown in Fig. 1 for the above bias conditions. If minority carriers cannot accumulate at the surface to form an inversion region, the depletion-region width continues to increase with increased positive bias and the capacitance drops toward zero as in a reverse biased p-n junction. The effect of a work-function difference $hs between the metal and the silicon, and of surface charges per unit area Qss located at the oxide-silicon interface, is simply to attract charges in the silicon much like the applied bias. It can be shown that this results in a parallel shift of the capacitance-voltage characteristic along the voltage axis by an amount corresponding to AV = -$bIs + Qss/Co. Theoretical curves have been calculated4 giving the capacitance of the MOS structure C normalized to the oxide capacitance Co vs the quantity VG here VG is the voltage applied to the metal field plate. In Fig. 2 such calculations are shown as points for a particular oxide thickness and bulk impurity concentration for a p-type semiconductor. (For an n-type semiconductor the curves would be mirror images of these.) All three cases, i.e., low frequency. high frequency, and depletion, are indicated. Also shown in the figure are recorder tracings of the characteristics of actual devices. These characteristics have been shifted along the voltage axis to compensate the effect of surface charges and work-function difference. It is evident that agreement between experiment and theory is good. The nature of this shift along the voltage axis is

Jan 1, 1965

By R. A. Thomas, R. L. Solbod

The importance of transverse diffusion on the finger development in a miscible-phase displacement at an adverse mobility ratio of tbree was studied in a porous plate 1/4-in. thick, 3-in. wide and 18-in. long. Fast displacement rates (29 ft/D) and slow rates (1.6 ft/D) were used to determine the effect of residence time on the geometry of the fingers. The shape of the fingers was observed directly by use of the X-ray technique. At fast rates numerous narrow fingers were observed, but at slow rates a single somewhat bulging finger was produced. The amount of material moved transversely by diffusion across the plate was sufficient to modify the finger geometry in the slow-rate run because of the long residence time. These results are in contradiction to some of the postulates in the literature. The composition of the effluent stream, however, was not affected by the flow rate. This result is not inconsistent with the observed change in the shape of the finger in a short model, but it seems likely that a short model does not offer adequate and proper scaling of the reservoir. The model used was probably a valid one for studying the effect of transverse diffusion on the finger geometry, but a longer model would be needed for proper scaling of the effect of the change in the finger shape on the efficiency of displacement as measured by the composition of the effluent stream. INTRODUCTION Fingering can be defined as the uneven advance of the injected phase as it moves into a porous medium displacing the resident phase from the pore spaces of the rock. The use of this term is usually restticted to the situation in which the displacing phase is less viscous or more mobile than the fluid being displaced. Under these conditions, not only are fingers formed, but the length and width of the fingers grow with distance traveled in the porous medium. This subject has become one of great interest to the oil industry because of the present trend toward the use of various forms of miscible-phase displacement to increase oil recovery. Since in nearly all of the known modifications of the miscible-phase displacements an unfavorable mobility ratio exists (the displacing phase has a lower viscosity than that of the crude oil), the conditions are proper for fingering to develop. An appreciable amount of fingering appears to be a severe handicap to these processes for it increases the volume of agent required for the process to be a success, and such an increase puts a severe strain on the economics of the proposed processes. In some cases, such as for a mobility ratio of 200 unfavorable, it has already been demonstrated that the proposed process would not be economic if the fingering in the field were to be of the same magnitude as that observed in the laboratory. A number of aspects of fingering have been studied and reported in the literature. While the phenomenon of fingering cannot be regarded as a completely understood subject, considerable information exists on the effect of the path length and the mobility ratio on the growth of fingers. Less-complete data are available on the effect of the diameter of the flow path on the character and amount of the fingering, and even less agreement in results exists on the effect of rate of flow on the nature of fingering. This paper deals with one aspect of this latter subject. OBJECTIVE The objective of this study was narrowed down to one rather specific feature of the behavior of fingers in miscible-phase displacement in porous media. The variable studied was the effect of rate of flow on the nature and the development of fingers. It should be made clear at this point that, while rate was the apparent variable, the real variable was residence time; that is, at low rates the fluids are present at a given spot in the porous medium for a longer time interval than at fast rates. The purpose of the study, therefore, was to determine the changes which occur in the fingering and the possible benefits which might accrue from a longer residence time during that period when fingers are

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By H. W. Hindry

This paper presents the ingredients com-~osing a type of oil-base mud that has been successfully used in drilling oil horizons in California, the effect of ingredient concentrations on physical properties, methods of handling at the well and possible advantages of a waterless drilling fluid with excellent plastering properties. Introduction An oil-base mud is a rotary drilling fluid in which oil has been substituted for water as the principal liquid ingredient. In recent years such a mud has been developed and used successfully for drilling the oil horizons of wells in various Calilornia fields. There are several types of oil-base mud, but only the type that is currently used to any appreciable extent will be considered at this time. The oil-base drilling-mud compositions used by Shell Oil Company, Incorporated have been covered by several patent applications on which patents are expected to issue at an early date. The purpose of this paper is to present data on the fundamental design of the mud; the ingredients used and their specifications; the effect of ingredient concentration on physical properties; the selection of the proper mud; the facilities needed for handling the mud; and a general discussion on drilling with oil-base mud. In view of the early stage of development of oil-base mud, the great number of vari- ables, and the almost unlimited possible combinations of these. variables, which in turn require extensive laboratory study, there are certain irregularities and omis. sions in the data presented here. However, it is believed that sufficient data are at hand to permit a fairly complete analysis of the characteristics of oil-base muds. In view of the excellent plastering properties of oil-base mud when properly proportioned, its use should: (I) minimize the possibility of impairing the natural flow potentialities of the producing horizon such as that resulting from infiltration of water from water-base muds; (2) permit smaller clearances for setting liners, since the mud sheath has no appreciable thickness; (3) eliminate the possibility of clogging the perforations of the liner with thick mud sheath; (4) facilitate the removal of the mud sheath from the walls of the hole, for its mud sheath has no appreciable strength; (5) assist in drilling through formations, such as "heaving shale," where water wetting appears to be a source of difficulty. (6) permit cores to be obtained without contamination from drilling water. Fundamental Design of an Oil-base Mud In the design of any rotary drilling mud it is necessary to select materials that will fulfill the following requirements: (I) act as the liquid medium and regulate the viscosity; (2) impart initial and final plastering properties; (3) give gel strength and structure in order to prevent settling; (4) serve as a weighting material. The

Jan 1, 1941

By G. R. Leverant, C. P. Sullivan

To evaluate the effect of a dispersion of nondeform-able, incoherent, second-phase particles on high-strain cyclic deformation and fracture, recrystallized TD-nickel (Ni-2ThO2) and a commercially pure nickel, Ni-200, were fatigued under strain control at total strain ranges varying from 0.009 to 0.036. Relative to the Ni-200, the slip at the surface of the TD-nickel was more wavy and discontinuous due to the presence of the thoria particles. This made crevice formation (incipient cracking) within slip bands more difficult in TD-nickel than in Ni-200. Both materials cyclically hardened to a constant (saturation) flow stress which increased with increasing plastic strain amplitude. Cellular substructures were developed in both materials during cycling. The cell size in TD-nickel was controlled by the thoria particle distribution and was independent of plastic strain amplitude over the range investigated. The cell size in Ni-ZOO was larger than that in TD-nickel at similar plastic strain amplitudes and was a function of plastic strain amplitude. These results, together with the cyclic stress-strain curves for both materials, are discussed in terms of a model for fatigue strain accommodation at saturation recently proposed by Feltner and Laird. NUMEROUS fatigue investigations have considered the interrelation of slip character, dislocation substructure, and cracking in pure metals and solid-solution alloys. However, except for the studies of the low-strain fatigue of internally oxidized copper alloys1 and cast, dispersion-strengthened lead,&apos; little is known about the effects which small, incoherent, nondeform-able, second-phase particles have on cyclic deformation and cracking processes. Effects due to the particles alone are often obscured by a dislocation substructure introduced during thermomechanical processing of dispersion-strengthened metals. In the present study, recrystallized TD-nickel and a commercially pure nickel, Ni-200, were employed to evaluate the effect of a thoria dispersion on high-strai fatigue deformation and cracking at room temperature. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in.-thick stress-relieved plate which had been subjected to a proprietary schedule of thermomechanical treatments, and the Ni-200 as 3/4-in. bar which was subsequently annealed for 2 hr at 850°C in argon resulting in an average grain diameter of 0.05 mm. The compositions of these materials are given in Table I. The microstructure of the TD-nickel consisted of elongated grains parallel to the primary working direction with an average width of 0.16 mm, Fig. l(a). Many fine annealing twins were present indicating that the starting material was in a recrystallized condition; this supposition was confirmed by the absence of of any extensive dislocation substructure, Fig. l(b). Sheetlike stringers parallel to the rolling direction were occasionally seen both within grains and at grain boundaries. Some approximately spherical particles about 2 in diam, which may correspond to exceptionally large thoria particle aggregates, were also present. The average Young&apos;s modulus of the plate material in the rolling direction was 21.8 X 106 psi which is consistent with a {100}<001>recrystalliza-tion texture3&apos;* being prominent. In transmission microscopy, the 2.3 vol pct of thoria particles generally appeared to be uniformly distributed although some clusters, 0.1 to 0.3 in diam, of larger particles were observed as previously reported for TD-nickel sheet,5 and stringering of particles was present in some areas as welt. The average diameter of the thoria particles was 450A with a calculated mean planar center-to-center spacing of 2100A, as determined by quantitative metallographic analysis.= The 0.2 pct offset yield stress was 36,000 psi which agrees with the value predicted by the modified Orowan relation7 for edge dislocations bowing between thoria particles of the size and spacing observed in the present investigation. Fig. 2 illustrates the specimen design employed for the axial high-strain fatigue testing. Adapters were screwed onto the threaded portions of each specimen so that testing could be performed in the same manner as that reported for buttonhead specimens.8 Stressing was coincident with the working direction for both materials. The gage section of each specimen was electropolished and lightly etched prior to testing. The total strain was controlled, being varied between zero and a maximum tensile strain ranging from 0.009 to 0.036. In addition to these tests, a circum-ferentially notched TD-nickel specimen was cycled over a total strain range of 0.0075. The same strain

Jan 1, 1969

By S. Skowronski

PURPOSE OF INVESTIGATION Since cuprous chloride melts at 418° C., boils at 954° C. to 1033° C.,1 and is known to be volatile at a much lower temperature, the presence of chlorine in any form in or on copper to be melted has always been looked upon by copper refiners as a possible source of-serious copper loss. Although this fact has been known for some time, the copper literature contains little or no information regarding it and the field seems .never to have been properly investigated from a metallurgical standpoint. According to Greenawalt,2 cupric chloride, CuCl2, when ignited gives cuprous chloride; therefore cuprous chloride is always formed when copper enters into reaction with chlorine at a high temperature. Cuprous chloride melts somewhat below a dull red heat, and does not volatilize in closed vessels, even if strongly heated, but if heated in the air it goes off as a white vapor. Hofman3 gives the melting point of cuprous chloride

Jan 2, 1919

By James H. Courtright, Kenyon Richard

L. H. Hart (Chief Geologist, American Smelting & Refining Co.)— Because of a widely recognized association between breccia pipes of one form or another and many important copper deposits, conditions under which breccia pipes develop have been of great scientific interest for many years. Since these phenomena first attracted attention, many theories have been advanced to explain their origin. This is not unexpected, since it is likely that they have been formed by and under a wide range of conditions. Moreover, the entire subject is confused by the fact that the term brec-cia pipe is applied to a wide variety of occurrences. To discuss any part of the subject intelligently, therefore, it is necessary to start with definitions of the terms used. In their discussion of the Toquepala deposit, Richard and Courtright have carefully defined the terms they have used in their presentation of a very logical geological history of Toquepala breccias. This is a real contribution, as there is no reference in the literature known to the writer where the history of a series of breccia pipe epochs, confined essentially within one channelway, may be read with the degree of certainty that appears to be possible at Toquepala. Although the following comments are intended primarily to emphasize points brought out in the article by Richard and Courtright, certan subsequent detailed mapping by Hollister and Houston7 within the main central mineralized area of the Toquepala deposits not only supports most of Richard&apos;s and Courtright&apos;s con- clusions but also contributes additional facts that strengthen and broaden the whole concept of the origin of the Toquepala breccia pipes. In detailed mapping by Hollister and Houston,&apos; the most significant feature disclosed is a well developed system of concentric fracturing in rocks peripheral to the main breccia pipe throughout an arc of 300°, interrupted only by the late dacite agglomerate in the north quadrant. Although Richard and Courtright noted that such fractures were developed in the southern and southeastern areas, continuity in the east and west quadrants is established by consistent orientation of the stronger set of fractures and joints. The existence of these structural weakness trends is emphasized by the emplacement of dike-like phenomena in and along members of this fracture system. Richard and Courtright described one of these dikes in the southeast quadrant. They referred to it as a ring-dike, composed of dacite porphyry. This suggests an apparent structural control of at least a part of the dacite porphyry intrusion by features related to the Toquepala breccia pipe center. This raises a perplexing question, since the dacite porphyry intrusion had been presumed to antedate breccia pipe activity. However, if this ring-dike is related to the breccia pipe center, it may indicate that some part of the dacite porphyry intrusion advanced in a manner resulting in an intensely localized stress center, which produced the concentrically arranged fracture system. The ring-dike would then appear to be evidence strongly sug-

Jan 1, 1959

By William L. Fink, H. R. Freche

The constitution of the aluminum-cobalt alloys has been the subject of relatively few investigations. Brunckl analyzed the residue which remained after treating the 17 per cent cobalt alloy with dilute hydrochloric acid. The results of the analyses indicated the existence of a compound Co3Al13. Guillet2 published a liquidus for the aluminum-cobalt system which contained two maxima corresponding to CoA16 and CoAl2 and two eutectic points at 30 and 74 per cent Co. The most extensive investigation of the system was carried out by Gwyer13 whose results are summarized in Fig. 1. It will be noted that at the aluminum end there is a suppressed eutectic at 644&apos; C. By extrapolation of the duration of the eutectic arrest to zero, the composition of the compound was placed at Co3Al13. Another thermal arrest was noted at 550" C., which Gwyer attributed to a peritectic reaction. The present investigation of the aluminum end of the aluminum-cobalt system is the eleventh of a series dealing with the constitution of aluminum-rich alloys prepared from electrolytically refined a1uminum.l Preparation of Alloys.—The alloys used in this work were all prepared from electrolytically refined aluminum, the analysis of which is shown in Table 1. In preparing some of the alloys, metallic cobalt (98 to 99 per cent) was used either directly or in the form of an intermediate alloy, the composition of which is given in Table 1. In order to obtain alloys of higher purity, cobalt was introduced into some of the alloys by means of chemically pure cobaltous chloride which was readily reduced by the aluminum. A small electric furnace with nickel-chromium heating elements was used in the preparation of the alloys. Chemical Analysis.—An analysis sample from each melt was chill-cast in the form of a plate 3/16 in. thick. In all cases the casting temperature was well above the liquidus. Cobalt was determined electrolytically in all alloys containing more than 0.05 per cent cobalt and by the nitroso-

Jan 1, 1932

TWO American students entered the École des Mines in 1856, Joseph Lesley of Philadelphia and Thomas Egleston of New York. Lesley remained there only one year, but Egleston completed the whole curriculum and received, in 1860, the certificate given to foreign students in lieu of the official appointment and degree awarded French students. Returning home he received, in 1861, an appointment by Secretary Henry of the Smithsonian Institution to sort, label, and arrange the collections of mineralogical and geological specimens which had been brought to Washington by the various government exploring expeditions in the West. Thomas Egleston, born in New York City on Dec. 9, 1832, was the son of Thomas Jefferson Egleston, who came to New York from Massachusetts some time before 1829. The first American ancestor of the family had settled near Dorchester in 1630. T. J. Egleston and Joseph Battell established an iron-merchandizing business* at 166 South St., New York, which prospered exceedingly; so much so that when Thomas J. Egleston died, July. 12, 1861, his estate had a book value of over $500,000. Since an older brother was expected eventually to take over this business, Thomas, who had a liking for science, went to Yale, where he completed the regular four-year course in 1854, and then remained another year for advanced work in chemistry under Silliman. One biographer says he went to Europe, early in 1856, on account of his health. It was the custom at that time for wealthy young men to make a tour of Europe after completing their academic education. Whatever the precise reason, he began scientific work at the Jardin des Plantes in Paris but soon trans-

Jan 1, 1941

By G. W. Jones, G. S. Scott

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer&apos;s intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist&apos;s knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942