Search Documents

By Ralph J. Schilthuis, William Hurst

The nature of the forces that are important in producing the oil in the East Texas field and the manner in which these forces are affected by the rate of production have always been problems of outstanding interest. These questions are of great interest to the industry as a whole on account of the economic importance of the East Texas field and to the engineers in particular on account of the unique character and behavior of the field. Subsurface pressure data throughout the field have been collected systematically, so that a quite complete history of the reservoir pressures has been kept as the field has been developed and produced. Subsurface samples of the oil and gas have been taken and these have been examined to obtain data on the physical properties of the reservoir fluids under the actual conditions of temperature and pressure. All of these data have been valuable because they have afforded the basis for a careful study of the means by which the oil is produced. It is the purpose of this discussion first to point out several of the important facts revealed by the data mentioned and then to describe studies that have been made concerning the interpretation of these facts. Reservoir Pressure Data and Properties of Oil The reservoir pressure data on the East Texas field have shown conclusively that the pressures are readily affected by changes in the rate at which the field is produced. This can well be seen in Fig. 1, where the average reservoir pressures obtained from time to time are plotted with the daily production rates and the cumulative production of the field. It is noted that the average reservoir pressure has declined irregularly, depending upon the rate of production, from the estimated original value of 1625 Ib. per sq. in. to the value of 1228 lb. per sq. in. observed for Aug. 11,1934. The decline in pressure has been more rapid at the higher rates of production than at the lower rates. In contrast, the average reservoir pressure has increased, on several occasions, upon reduction of the withdrawal rate from a high value to a lower value. The reservoir pressure data have also shown that a definite gradient in pressure has existed across the field from west to east since the begin-

Jan 1, 1935

INTRODUCTION In the preceding chapters we have discussed the various elements of mineral economic analysis, their interrelationships, and the most accepted and advanced techniques by which these elements are manipulated to provide the decision maker quantitative measurements for judging alternate investment opportunities. Regardless of how carefully the economic evaluation is made, and how comprehensive the study of economic parameters has been, uncertainty still remains a significant factor in the outcome of the analysis. The investor or money manager is acutely aware of the uncertainty factor. Many of the economic parameters are functions of economic forecasts and value estimates that can- not be known with any degree of certainty. The postulated DCF-ROR is based upon certain estimates representing "best guess" values, and a single point parameter DCF-ROR analysis represents a combination of "best guesses." The wise decision maker looks at such an analysis and asks the "what if" questions. What if the production cost is 10% higher than the estimate? What if there is an overrun in construction costs? What if the mineral price falls lower than expected? What will be the effect of a higher royalty rate? Many more such questions may arise in trying to assess the total risk involved in funding a mineral project. Prior to the advent of the computer it was difficult to answer all such anticipated questions because of the many laborious calculations involved. Now, with the aid of the computer, most of these questions can be answered by the analyst at the same time the original computations are made by using the process of sensitivity analysis. Sensitivity analysis shows the effect of critical parameter changes upon the DCF-ROR or other profitability measure. When probability of occurrence can be associated with the various parameter value levels, sensitivity analysis becomes probabilistic analysis, and the risk factor can be quantitized in terms of total probability. SENSITIVITY ANALYSIS The determination of the sensitivity of the profitability index (usually the DCF-ROR) to changes in the various economic parameters, taking them one at a time, is called sensitivity analysis. The analysis may be performed for any number of parameters involved in the DCF-ROR computation. Generally, in mineral evaluations the most sensitive and most tested parameters are: the metal or mineral price, the operating cost, the annual production grade, and the initial capital invest-

Jan 1, 1980

By A. J. Lyon

THE stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening; which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging-heating in a temperature range below 170° C. (340° F.)-will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1928

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law's constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By H. Landsberg

In a previous report1 it was pointed out that a successful attack on roof troubles has to be preceded by extensive scouting. As Lord Kelvin once said, scientific progress can be made only if accurate data are available: "unless you measure, you do not know." The Convergence Recorder For the observation of roof movements in mines the convergence recorder has shown that it will enable us to get some of the necessary information. Results with convergence recorders were first published by Winstanley and other English investigators for rapidly moving longwall faces. In their investigations the speed of work and the heavy overburden produced a considerable amount of absolute values of convergence in a short time. Under the conditions frequently encountered in our investigations in Central Pennsylvania, under shallow, overburden and in mines with slowly proceeding extraction, the movements observed were much less in absolute value, for an equal interval of time. This mas partly because the mines in which our studies were carried on frequently had idle days, sometimes four or five in succession. Therefore continuous records were not employed and a simple convergence gauge was built. In its first models, it consisted only of two telescoping tubes pressed against roof and floor by a coil spring. At the side of the lower tube a rule divided into 1/2-mm. divisions mas fixed and a knife-edge, which was attached to the upper tube, mas slid over the scale in case of convergence between roof and floor. While the larger motions could be read on this device, it seemed to be desirable to increase the accuracy by inserting between the two tubes a dial meter reading in 1/1000 in. Such a gauge was first built in April 1937 and installed for experimental purposes in a bituminous coal mine in Pennsylvania (Fig. I). It was read at least once daily, 24 hr. apart, and if feasible at shorter intervals. After several months of experience it can be said that this type of gauge answers the scientific as well as the practical needs. It is easier to handle than the recorder; no clock is used, there are no pen troubles. The price of

Jan 1, 1938

By H. Landsberg

In a previous report1 it was pointed out that a successful attack on roof troubles has to be preceded by extensive scouting. As Lord Kelvin once said, scientific progress can be made only if accurate data are available: "unless you measure, you do not know." The Convergence Recorder For the observation of roof movements in mines the convergence recorder has shown that it will enable us to get some of the necessary information. Results with convergence recorders were first published by Winstanley and other English investigators for rapidly moving longwall faces. In their investigations the speed of work and the heavy overburden produced a considerable amount of absolute values of convergence in a short time. Under the conditions frequently encountered in our investigations in Central Pennsylvania, under shallow, overburden and in mines with slowly proceeding extraction, the movements observed were much less in absolute value, for an equal interval of time. This mas partly because the mines in which our studies were carried on frequently had idle days, sometimes four or five in succession. Therefore continuous records were not employed and a simple convergence gauge was built. In its first models, it consisted only of two telescoping tubes pressed against roof and floor by a coil spring. At the side of the lower tube a rule divided into 1/2-mm. divisions mas fixed and a knife-edge, which was attached to the upper tube, mas slid over the scale in case of convergence between roof and floor. While the larger motions could be read on this device, it seemed to be desirable to increase the accuracy by inserting between the two tubes a dial meter reading in 1/1000 in. Such a gauge was first built in April 1937 and installed for experimental purposes in a bituminous coal mine in Pennsylvania (Fig. I). It was read at least once daily, 24 hr. apart, and if feasible at shorter intervals. After several months of experience it can be said that this type of gauge answers the scientific as well as the practical needs. It is easier to handle than the recorder; no clock is used, there are no pen troubles. The price of

Jan 1, 1938

By John Norton

IN recent years, the damping capacity of metals has come to be recognized as an important index of certain types of structural change. In a number of instances, this property has proved to be particularly sensitive, but insufficient work has been done to permit a general inter-pretation. There is considerable question at the present time as to just what factors are responsible for the internal dissipation of energy when a metal is carried through a cycle of stress, and these factors must be ascertained if the value of the damping method as a metallurgical tool is to be determined. Since internal stresses are among the chief causes of dissipation of internal energy, or damping capacity, it was thought that a study of the changes in damping during the recovery and recrystalliza-tion of a cold-worked metal might throw some light upon the subject, particularly if the damping changes were correlated with other properties that are better understood. Probably more work has been done on the recrystallization phenomena of alpha brass than on any other metal, so this was chosen as the material for the present investigation. Damping measurements on brass have been made by Förster and Köster.1 They showed that the annealing of a brass that had been cold-drawn to 50 per cent reduction produced a rapid fall in the damping, a flat minimum occurring at approximately the temperature of recrystal-lization. The damping remained at a low value until grain growth was well under way and then it increased rapidly with increasing grain size. Köster and Rosenthal2 continued the work in greater detail. They pointed out that the damping decrease does not correspond to the hard-ness drop but occurs at a lower temperature, suggesting that the relief or redistribution of internal stresses has a large effect while the actual recrystallization effect is small. They also show the increase in damping at the higher annealing temperatures. Their curves are reproduced in Fig. 1.

Jan 1, 1940

By R. B. G. Yeo

The effects of alloy additions on the M, and A, temperatures of an Fe-22.5 pct Ni alloy have been determined. Increasing amounts of titanium, colum-bium, vanadium, and silicon raise and then lower M,while raising A, cmtinuously. Cobalt raises both M, and A,. Aluminum has little effect on Ms but raises A,. Chromium md nickel lower M, and A,. It is proposed that elements raise M, in accordance with their effect on the Ae3 temperature of iron until the lattice becomes stiffened against the shear transformation so that M, is then lowered. An anomaly, first pointed out by Zener,1 arises in steels when the addition of elements, such as molybdenum and tungsten, which raise the Ae3 temperature, also lower the M, temperature.2'3 During the development of a series of martensitic precipitation-hardening (maraging) steels, the effect of several elements on the transformation of austenite to martensite was studied. The results show that under suitable conditions several elements which raise Ae3 also raise the M, and A, temperatures. PREPARATION OF MATERIALS STUDIED A series of alloys was made in which cobalt, titanium, columbium, vanadium, silicon, aluminum, molybdenum, chromium, and nickel were added to an iron base containing 22.5 pct Ni. The compositions of the alloys prepared are given in Table I. The residual manganese contents of the heats were in the range of 0.030 to 0.35 pct, silicon 0.05 to 0.1 pct, carbon 0.0008 to 0.009 pct, and nitrogen from 0 to 0.004 uct. The allois were made as 50-lb induction heats starting with electro-iron and electro-nickel, melted in air to oxidize impurities. Additions of silico-manganese and ferro-silicon were made after which the power was turned off to allow the products of deoxidation to rise and be skimmed from the surface of the melt. The furnace chamber was pumped down to a pressure of 5 p and the charge was heated to 2900°F for the addition of other alloying elements. The heats were poured into five 10-lb ingots, making successive alloy additions to each. The ingots were soaked for 2 hr at 2300°F and hot-worked to 3/4-in.-diam bars. This stock was heated to 1500°F for 1

Jan 1, 1963

By Rudolph G. Wuerker

The progress made in testing the strength of rocks and minerals as they are encountered in mine operation is reviewed. An attempt is made to correlate these physical measurements with abrasive hardness, grindability, and behavior in comminution on one hand and fracture of rocks in pillars and roof control on the other.

Jan 11, 1953

By J. F. Martin, L. M. Melnick, R. Rapp, R. C. Takacs

Recent studies on the determination of hydrogen in steel have shown that the hot-extraction method for removing hydrogen from a solid sample is preferable to its removal from a molten sample by vacuum fusion or by fusion in vacuum with tin. A number of techniques are available, however, for determining the hydrogen so extracted. They include: thermal conductivity, gas chromatography, pressure measurement before and after catalytic oxidation of the hydrogen to water and removal of the water, and pressure measurement before and after diffusion of the hydrogen through a palladium membrane. These techniques have been evaluated on the basis of initial cost, maintenance, speed and accuracy of analysis, and applicable concentration range. The results of this study showed that the palladium-membrane technique is best suited for routine use. FOR some time investigators have been concerned with the origin, form, and effect of hydrogen in steel. In such stdies', the analysis for hydrogen constitutes one of the most important phases. It is quite apparent that the results for hydrogen concentrations in a given steel are dependent on the method of obtaining the sample, storage of the sample until analysis, preparation of the sample, and analysis of the sample, including all the facets inherent in the calibration and operation of an apparatus for gas analysis. There are a number of means available for determining hydrogen. This is a critical study of some of the more common techniques in use today. In most conventional melting and casting methods, hydrogen concentrations of 4 to 6 parts per million (ppm) in steel are quite common. Because of the undesirable effects of hydrogen on steel there has been increased use of techniques such as vacuum melting,' vacuum casting, and ladle-to-ladle stream degassing, which lower the hydrogen content to levels on the order of 1 to 2 ppm. Therefore, the method used for determining hydrogen in steel must be sensitive and precise. In any analytical procedure for gases in metals there are two distinct operations—the extraction of the gas from the metal and the analysis of the extracted gas. To extract the gas from the steel, three methods have been employed: 1) fusion of the sample with graphite at high temperature; 2) fusion with a flux, such as tin, at a lower temperature; and 3) extraction of the hydrogen from the solid sample at a temperature below the melting point of the steel. Fusion with graphite is the least-acceptable method. The blank in this method is higher and more variable than in either of the other two methods. The hydrogen fraction of the total gas composition usually is between 10 and 50 pct; thus, a larger analytical error is possible. The vacuum-tin fusion4 extraction of hydrogen is probably the most rapid method in use today; the extraction time is usually about 10 min. However, with this system a bake-out of the freshly charged tin for 2 hr is necessary and a change of crucible and a charge of fresh tin are required after each day of operation whether one or thirty samples have been analyzed. In addition, frequent checks of blank rates are required since CO and Na are continually being given up by the steel samples dissolved in the tin bath. The composition of the gas in this method lends itself readily to analysis; although the hydroge concentration may fall to as low as 50 pct, more often it is above 90 pct, thus allowing a more precise analysis (because of less interference from other gases). In 1940 ewell' published the hot-extraction method for extracting hydrogen from the solid sample, comparing analysis for hydrogen extracted at 600°C with similar analysis for the gas extracted at 1700°C by fusion with graphite. Good agreement for hydrogen was obtained between these two methods, provided sufficient time was allowed for extraction at the lower temperature. carsone obtained good results in his comparison of this hot-extraction method with vacuum-tin fusion. Subsequent work by Geller and sun7 and Hill and ohnson' has shown that steel samples should be heated to at least 800°C to effect the release not only of the diffusible hydrogen but also of the "residual" hydrogen that may be present as methane. Since the rate of evolution of hydrogene9l0 depends on such factors as sample size and composition, thermal history, and extent of cold work, a fixed extraction time is not possible. Extraction times of 30 min are normal, but 2 hr are not unusual. Induction or resistance heating may be used in the hot-extraction method. With resistance heating the

Jan 1, 1964

SAMUEL T. HOYT,? Minneapolis, Minn. (written discussion||).-The subject of grain inheritance in iron and steel is apparently one which can he considered from the point of view of the two laws governing the rate of formation of crystal nuclei and the linear velocity of crystallization, which have been investigated by Tammann and collaborators, and of the additional law of coalescence. According to the work of Tammann, both the nuclei number, which is taken to be the number of crystal nuclei to form per unit volume per unit time, and the linear velocity of crystalli-

Jan 5, 1918

By Nicholas J. Grant, David S. Bloom

An investigation of the Cr-Ni system has revealed that there exists a eutectoid transformation at about 1180°C. 'The transformation in chromium implied by the eutectoid reaction was detected at about 100°C below its melting point. Associated with the eutectoid transformation, a metastable transition structure has been found. THE Cr-Ni phase diagram is shown in current literature to be a simple eutectic system in which the high chromium end of the diagram is incompletely determined, Fig. 1. The last investigation of this system was undertaken in 1936.' Because of limitations in metal purity, especially of chromium, and temperature measuring techniques, the diagram should be accepted with some reservations, as was indicated by Hansen.V or examwle.-, the wresence of the compound Cr²Ni, with a tetragonal structure," remains unverified and incompatible with the simple eutectic diagram. The work reported here began because of discrepancies that appeared in experimental studies in the binary alloys Cr-Ni and in the ternary system Cr-Mo-Ni. The existing binary Cr-Ni diagram failed to provide a complete explanation of observations made by microscope, X-ray, and thermal analyses. Experimental Methods The materials employed were of a higher degree of purity than were available to previous investigators. The Mond nickel used had a nominal purity of 99.87 pct, while the electrolytic chromium analyzed 99.03 pct with the major impurity being 0.5 to 0.7 pct oxygen with some iron. All alloys were melted in a vacuum furnace to remove dissolved gases, sufficient carbon was added to the charge to combine with all the oxygen as CO. Final analysis determined the carbon as about 0.02 pct and the oxygen around 0.06 pct or slightly more. Stabilized zirconia crucibles and thermocouple protection tips were used throughout and contributed no detectable impurity to the melts, as long as the oxygen in the chromium was kept low. Heats averaged about 250 g, which permitted about 2 in. of the thermocouple protection tips to be submerged. The temperature drop across the thermocouple protection tip was determined to be about 3°C, a minor source of error. The alloys, after removal from the vacuum furnace, were placed in a furnace operating in a purified argon atmosphere for the thermal analyses. An- nealed wolfram-molybdenum thermocouples provided the primary means of temperature determination, though a Pt-Pt-10 pct Rh couple was employed for a check when possible. A sensitive, high-speed Leeds and Northrup Speedomax recording potentiometer indicated the thermocouple output. X-ray diffraction patterns were obtained primarily on a Norelco unit, which permitted diffraction angles only up to 45" (28 = 90"). In general, either rotated or stationary solid samples were used, because it later evolved that many samples were susceptible to transformation resulting from the cold working involved in pulverizing. It was also noted that rotating a sample sometimes suppressed weak lines, so, usually, samples were not rotated. Later a high temperature camera was adapted for use at temperatures up to 1400 °C on the Norelco unit utilizing both solid and powdered samples. Unless otherwise noted, all X-ray patterns were made with a chromium tube and a vanadium filter. Further-

Jan 1, 1952

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By Arthur Knapp

The practical application of mud-laden fluids in wells has been the subject of many papers.' However, there seems to have been little investigation of what actually happens when mud-laden fluids are applied to a loose porous sand. The assumption is that the fluids penetrate the sands and that there is some plastering action. The degree of penetration and the relation of plastering action to wall stability is not generally known. This paper describes a series of experiments made in an attempt to observe, in laboratory apparatus, the action of mud-laden fluids under conditions simulating those to be found in a well. For the purposes of this discussion all fluids containing solid matter in suspension are mud-laden fluids. Series I: Penetration of the Pores of Uncemented Sands The subject of the penetration of porous formations by water is discussed in detail in Water-Supply Paper No. 67 of the U. S. Geological Survey. No attempt was made to repeat the experiments described therein. The results of the first experiment of this series are given simply to show the capacity of the apparatus used. The conditions in this first experiment were maintained throughout the remainder of this and the second series, except where noted. The experiments of Mills, McCoy, and others on subsurface flows, adjustments, migrations, etc., deal with the oil, water or gas within the porous beds.V he experiments described herein deal with the conditions immediately surrounding the bore hole.

Jan 1, 1923

By Arthur Knapp

The practical application of mud-laden fluids in wells has been the subject of many papers.' However, there seems to have been little investigation of what actually happens when mud-laden fluids are applied to a loose porous sand. The assumption is that the fluids penetrate the sands and that there is some plastering action. The degree of penetration and the relation of plastering action to wall stability is not generally known. This paper describes a series of experiments made in an attempt to observe, in laboratory apparatus, the action of mud-laden fluids under conditions simulating those to be found in a well. For the purposes of this discussion all fluids containing solid matter in suspension are mud-laden fluids. Series I: Penetration of the Pores of Uncemented Sands The subject of the penetration of porous formations by water is discussed in detail in Water-Supply Paper No. 67 of the U. S. Geological Survey. No attempt was made to repeat the experiments described therein. The results of the first experiment of this series are given simply to show the capacity of the apparatus used. The conditions in this first experiment were maintained throughout the remainder of this and the second series, except where noted. The experiments of Mills, McCoy, and others on subsurface flows, adjustments, migrations, etc., deal with the oil, water or gas within the porous beds.V he experiments described herein deal with the conditions immediately surrounding the bore hole.

Jan 1, 1923

CAMBRIDGE, MASS., May 22, 1913. TO THE PRESIDENT, American Institute of Mining Engineers. Dear Sir: Referring to Mr. J. WV. Finch's letter printed in the Institute Forum of the May Bulletin, I am very much in sympathy with his suggestion that the Transactions be printed in several volumes devoted separately to the various subjects covered by the Institute papers, such as " Iron and Steel," "Mining Geology," " Precious and Base Metals," etc. The advantages of this plan appear to me so great and so obvious as to far outweigh any possible objections. At a meeting of the Iron and Steel Division Committee held on June 28, 1912, I moved that the Committee recommend to the Council that papers on Iron and Steel be published in separate annual volumes. The motion was seconded and passed. Since then I have never failed to repeat my request whenever an occasion presented itself, and I welcome the opportunity offered by Mr. Finch's communication to again call the attention of those interested to an innovation which appears to me so highly desirable. ALBERT SAUVEUR.

Jan 6, 1913

By George Gardner

THE application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous dis-charge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condi-tion often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies consid-erable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, there-fore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially pre-pared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation.

Jan 1, 1939

By P. R. Sperry

A METHOD was recently devised to indicate two or more successive stages of the migration of grain boundaries in aluminum, and to record the direction of the migration. This technique was used for the study of the various types of boundary migration occurring in high purity aluminum.' The method employs alternate annealing and electrolytic etching treatments, repeated as many times as desired. All successive sets of grain boun- dary positions revealed by the various etches appear superimposed on each other. The last etch is designed to leave an oxide film on the surface which is optically anisotropic. The orientation of the oxide film at each point is determined by the orientation of the underlying aluminum grain. When viewed with polarized light using crossed nicols and a Biot-Klein quartz plate, grains with differing orientations appear in different colors, as described by Hone and Pearson.' The last boundary positions are revealed by these color differences. The first step of the process is to obtain a desired starting grain size by annealing, for example, if high

Jan 1, 1951

Plans for the Petroleum Division during the ensuing year are in process of development, in contemplation of the usual fall meetings in the Mid-Continent and California areas, as well as the annual meeting to be held in New York in February, 1936. Houston, Texas has been suggested as the place for the Mid-Continent fall meeting, the exact date to be announced shortly. During the past year, the Division's technical programs, as in former years, have emphasized the wide fields of engineering endeavor in the petroleum industry yet remaining for more thorough investigation and discussion. An effort has been made to bring an international interest into the proceedings of the Division by inviting the participation of prominent foreign technologists. This viewpoint should promote a continuation in 1935 of past high standards, afford a more thorough understanding of problems throughout the membership, and maintain the Institute's position among the various technical organizations functioning particularly in the oil-producing and refining areas. In the list of subjects proposed for the fall meetings is the problem of estimating petroleum reserves. Various factors requiring study will include productive sand volume, porosity, average permeability, saturation, and types of recovery. Research papers are proposed dealing with energy consumption per unit of oil recovered, reservoir pressure or energy loss relationship to the usual volumetric method of estimation, and the study of oil and gas segregation within the reservoir. Other subjects tentatively suggested include new casing practice in relationship to wells producing from several productive zones, progress in lifting methods, repressuring, advanced methods in drilling economies, and the economics of conservation. Although the threat of overproduction yet remains, to a lesser degree than during the past few years, intensive activity is now being directed towards the discovery of new petroleum reserves. This situation undoubtedly will influence, in some considerable degree, the channels through which technical activities will be directed. A continuation of the commendable work on production statistics for the various oil-producing states and foreign countries has been effected. The usual papers dealing with the general economics of the industry will be reserved for the annual New York Meeting. The Stabilization Committee maintains its membership of nationwide authorities, and interest is manifest in new developments to meet the changing requirements of the industry.

Jan 1, 1935

By L. W. Kempf, R. S. Archer

The binary aluminum-silicon alloys have certain characteristic advantages which are now well known, and these alloys have come into considerable use during the past several years.' Their field of application has been limited to a certain extent, however, by their low yield point and hardness, low endurance limit, and relatively poor machining characteristics. These properties are improved by the addition of copper, and the ternary aluminum-silicon-copper alloys constitute an important class. The addition of copper decreases the corrosion resistance of the aluminum-silicon alloys and increases specific gravity. Magnesium is a hardening addition which seems to have relatively little effect on corrosion resistance, and which, of course, reduces specific gravity. The object of the work described in this paper was the development of alloys and heat treatments for the production of sand castings and permanent-mold castings having substantially all the advantages of the binary aluminum-silicon alloys together with mechanical properties improved to a degree permitting wider application. Constitution of Alloys Magnesium and silicon combine in aluminum alloys as the compound Mg2Si, which forms a binary system with aluminum. In alloys containing an excess of silicon over that required to form the compound, solidification ends with the freezing at 1022' F. (550' C.) of a ternary eutectic of aluminum, Mg²Si, and silicon. Judging from the horizontal projection of the liquidus surface as given by Hanson and Gayler,² this ternary eut,ectic contains about 13 per cent. silicon and 6 per cent. magnesium. All of the alloys discussed here contain excess silicon, so it

Jan 1, 1931