Search Documents

By Wood W, Bell A

Brown coal production in Victoria's Latrobe Valley Region (Figure 1) continues to rise and currently stands at around 50 Mt per annum. With the exception of around 2 Mt used to produce some 700 Kt of brown coal briquettes, this coal is mined by the State Electricity Commission to fuel large thermal power stations with a total installed capacity of just over 5 000 Megawatts. The moisture content of the coal as mined typically exceeds 60 per cent, making Latrobe Valley coal a markedly low rank fuel. The lack of heating value is, however, compensated for through power station design and by the fact that ash yield is very low, usually within the range of one per cent to four per cent on a dry basis. This means that compared with most other coals, the burning of Latrobe Valley brown coal produces relatively small quantities of waste products and discharges a minimal level of pollutants into the atmosphere. Even so, the inherent quality of Latrobe Valley coal does vary significantly from one area to another (Gloe, 1991; Barton et al, 1992) both on a local and a regional scale. Such variations need to be recognised and understood in order to not only realise efficiency gains in existing power stations but to properly assess resource potential for future utilisation and the application of new technologies. The principal aim of this paper is not to describe coal quality variation in detail or to speculate on the nature of and reasons for such variation. Rather, it is to simply underscore that significant differences do occur and that this is clearly a factor which needs to be considered in any evaluation of Latrobe Valley brown coal as a resource for the future.

Jan 1, 1992

By D. A. Ainsworth

"The first known use of activated carbon dates back to the Ancient Egyptians who utilized its adsorbent properties for purifying oils and medicinal purposes. Centuries later, the early ocean going vessels stored drinking water in wooden barrels, the inside of which had been charred. (However, by modern definition the carbon used in these applications could not truly be described as activated.) By the early 19th century, both wood and bone charcoal was in large scale use for the decolorization and purification of cane sugar.However, it was not until the beginning of the First World War that the potential of activated carbon was really capitalized upon. The advent of gas warfare necessitated the development of suitable respiratory devices for personnel protection. Granular activated carbon was used to this end as, indeed, it still is today.By the late 1930's there was considerable industrial scale use of carbon for both gaseous and liquid phase application and new manufacturing processes had been developed to satisfy the needs of industry. During the 1939-1945 war, a further significant development took place - the production of more sophisticated chemically impregnated carbon for the removal of both war and nerve gases."

Jan 1, 1984

By Helga Larravide

A new on-line database of literature about copper has been created through a joint undertaking by the Copper Development Association Inc. and PROCOBRE-Chile, with funding provided in part through the International Copper Association, Ltd. The new database will permit Spanish-speaking technologists to access publications maintained by PROCOBRE-Chile by means of standard keyword searches. In addition, a new Spanish- English thesaurus has been written to enable Spanish-speaking individuals to search d access the Technology and Environmental databases of the Copper Data Center, which together comprise more than 80,000 publications dealing with the production, properties, uses and environmental effects of copper. Planned expansion of the new Spanish literature database is described.

Jan 1, 1999

By Percy W. Bidwell

THE statisticians had defeated Germany months before she invaded Poland. With batteries of adding machines they had proved that she was suffering from serious deficiencies in critical food- stuffs and in practically all of the raw materials necessary for the conduct of modern warfare. Their calculations showed that with respect to fats, oils, wool, cotton, hides, petroleum, iron, copper and other metals, the Reich was bound to be at a great disadvantage vis-a-vis the French and British as long as the latter could keep open the lines of sea communication. The conclusion seemed obvious-"Germany can't win." The more cautious of the commentators introduced qualifications as to the length of the war and the tightness of the British and French blockade. They also made a third qualification as to the character of the struggle- whether it was to be a war of attrition or a war of movement. But since the invasion of Norway in April, there is no longer any doubt on this score. It is a war of movement-a war in which fuel, lubricants, and metals are being consumed on a scale never before seen.

Jan 1, 1940

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the fourth report of investigations dealing with the cooperative tests between the Bureau of Mines and industry on the use of electrolytic manganese in steelmaking. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steel 3/ the second with its use in acid electric steel practice, 4/ and the third with its use in low-carbon basic open-hearth steelmaking. 2/ A résumé of those investigations E7 appeared in the magazine STEEL. 5/ The present report deals with the use of electrolytic manganese in the manufacture of four types of stainless steel and the new Timken 16-25-6 alloy. The Bureau of Mines supplied The Timken Roller Bearing Co. with 62,000 pounds of electrolytic manganese for use in the tests.The electrolytic manganese was produced at the Bureau of Mines pilot plant, Boulder City, Nev., by the process developed by the Bureau and described in Bulletin 463, Operation of Electrolytic Manganese Pilot Plant, Boulder City, Nev., by J. H. Jacobs. J. W. Hunter, W. H. Yarroll, P. E. Churchward, R. G. Knickerbocker, R. W. Lewis, H.A. Heller, and J. H. Linck. The workcarried out under the direction of R. S. Dean, formerly assistant director, Bureau of Mines, and R. G. Knickerbocker, formerly chief, metallurgical branch, as part of a long-range program involving the development, manufacture, and use of manganese from domestic ores. Preliminary arrangements for the plant tests were made by the late A. A. Dow. 7/"

Jun 1, 1947

By J. Clark

The objective of this study has been to determine the state of the art in underground, thin-seam-mining systems, to identify new technology and procedures that would reduce the hazards of thin-seam mining and to recommend areas for further research. The study was carried out in two phases, the first of these being devoted to a survey of authoritative literature. Subsequently, the practices adopted in the various mining countries were analysed and comparisons made to identify machines and methods with the potential for application in the USA. Published figures on US bituminous coal reserves show the high proportion contained in thin seams and US accident statistics demonstrate that the risk is greater in thin-seam operations. A comparison has been made with the experiences of foreign operations. The Phase 11 study proceeded along two separate avenues to examine the distinctive problems associated with seam thicknesses above and below 30 in. Current systems of mining appropriate to seams greater than 30 in were elaborated and compared by means of a simulation exercise in terms of safety, production and cost. For seams below 30 in, less conventional systems, some presently disused, were studied and their potential evaluated; the research and development work necessary to make them viable has been indicated.

Jan 1, 1980

By Georgene Renner, William R. Yernberg, Steve Kral

Agapito Associates (AAI) provides consulting services in geo-engineering, mining engineering and related disciplines. Founded in 1978, the firm operates out of offices in Grand Junction, CO, Golden, CO and Lombard, IL. Members of the staff include mining, civil and geological engineers, physicists, geologists, numerical analysts, computer specialists, instrumentation specialists, plus administration and technical support personnel. AAI has provided consulting and engineering services to mining companies producing base metals, precious metals, coal, potash, trona, limestone, oil shale and salt, and to defense and nuclear-waste disposal industries. AAI also provides services for measuring in situ horizontal stresses using an advanced biaxial overcore stress downhole measurement system developed by Sigra of Australia. Since 1978, AAI has measured in situ stress in copper, oil shale, molybdenum, trona, limestone and coal mines, and in tunnels and concrete structures. Since 1994, the staff has completed 527 overcore stress determinations. AAI has the equipment and personnel for overcoring, sample coring and instrumentation installation in limited access, surface and underground mines. Portable Longyear CP-65 drills, borehole deformation gauges and strain indicators are used for difficult-access overcoring and are permissible for use in gassy mines.

Jan 1, 2006

By Jean Cayouette, Paul Blatter, Paul Cousin

"The Laronde mill was commissioned in 1988 and has been treating the Laronde Penna ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually.In 2008, the Goldex plant began trucking high grade (35-45 g/t Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold grade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine.Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa).INTRODUCTIONFollowing the 2000 to 2003 expansions, the Laronde plant evolved into a mature milling complex with developed processing, man power, and water treatment capabilities able to accommodate the complex Laronde ore. The ore requires a series of grinding, copper/lead flotation and separation, zinc flotation, zinc tails precious metals leaching, followed by a counter-current decantation circuit and Merrill Crowe precipitation. A paste backfill and SO2-air cyanide destruction operate intermittently. The tailings area has a dedicated cyanide destruction and metals precipitation plant prior to water recycling to the mill. A biological water treatment plant was put into service in 2004 to address the build-up of thiocyanate in the tailings ponds at Laronde. This was the result of the high sulphide content of the Laronde ore and 90% recirculation of the process water. The plant uses bacteria to oxidize and destroy thiocyanate, and removes phosphate from the water before it is released to the environment."

Jan 1, 2011

By M. Mahan, D. D. Blue, O. C. Garst, F. Fraas, L. Fink

"Early in World War II it became apparent that the known bauxite re- serves might not be adequate to supply the demands of the American aluminum-producing industry, as the transportation of bauxite from abroad to this country might easily be interfered with by hostile action. Consequently, the Bureau of Mines set up an intensive, well-integrated program for the production of cell-grade alumina from low-grade domestic ores. This pro-gram of investigation covered the production of alumina from clay, alumite, red mud, and other low- and marginal-grade ores. In line with the Bureau's usual policy of conservation of natural resources, it was decided that the investigation should be extended to cover the production of alumina and other valuable byproducts from aluminum dross.Statistical information showed that during the year 1943-44, an average of 2,900 tons of aluminum dross was generated monthly. This dross, after partial removal of free metal, had an average metallic aluminum content of approximately 9 percent. Some of this dross was produced by the melting of alloyed aluminum; but a large proportion 1,700 out of 2,900 tons - was generated by two producers of primary aluminum, and the dross did not contain an great proportion of alloying metals. Compared with dross from other sources, this 60 percent of the country's capacity can be assumed to have relatively uniform composition. Moreovcr, the problem of collection and distribution can be minimized because of the relatively small number of plants included in the organization of these two producers of virgin metal.Except for large pieces of metallic aluminum that easily can be mechanically separated for remelting, this dross has been discarded and scrapped. Inasmuch as chemical analyses show that the alumina content of dross is far higher-than ordinary ores - 111 percent alumina equivalent in dross compared to 57 percent alumina in bauxite - aluminum dross is a far richer source of aluminum than any known naturally occurring ores. The discard, of this waste material during the war and reconversion periods would be unsound economically. The work reported herein describes tests at the College Park Station of the Bureau of Mines on the recovery of metal, alumina, ammonia, methane, and abrasive-grade corundum from dross."

May 1, 1946

By Arun .. J. Basu

The paper introduces Intelligent Air Management (IAM) as the core activity of M&I Group of Companies (M&I) for providing a total solution to any air management problems for mining and mineral processing operations implementing a comprehensive systems approach through a world-wide network of strategic alliance partners and in-house engineering team and manufacturing facilities in Mississauga, Ontario, Canada. Recommendations for energy-efficient ventilation in a vibration and noise free environment are made with the patented and innovative solutions supported by extensive computational fluid dynamics (CFD) studies. The solution scope extends from an intelligent and integrated exhaust silencer to a complete ventilation sys-tem solution including inlet and outlet control design and ducting for diffusers and silencers.

Apr 1, 2005

By Kevan Ford, Getulio Junior, Rob Henderson, Wayne Philips, Chris Martin, Rob Thorpe

"Plant 2 at the Kinross Paracatu gold operation in Minas Gerais State, Brazil, was commissioned in late 2008. Designed to be the largest tonnage, lowest grade gold milling operation in the world, Plant 2’s throughput has steadily increased towards its design capacity of 5087 tons per hour.The plant employs a gold-specific flotation scheme to recover the majority of gold, which is present as discrete free gold particles. Additional gold is recovered by jigs in the grinding circuit, and the jig concentrates are reground, upgraded and subjected to intensive cyanide leaching. The flotation cleaner concentrate is reground and leached using a conventional CIL circuit.One year after start-up, with the plant stabilizing operationally, plant circuit surveys were completed by a joint team from Kinross Paracatu and Blue Coast Metallurgy Ltd. The surveys audited the flotation and concentrate treatment circuits to investigate the metallurgical performance.This paper describes the Plant 2 operation and how the surveys were designed and executed. Some of the quality control systems that were employed to provide meaningful data from such a low grade gold ore are described and findings and actions taken to improve metallurgy as a consequence of the surveys are discussed.INTRODUCTIONThe Paracatu mine is located two kilometres north of the city of Paracatu, in the north western portion of the state of Minas Gerais, Brazil, 230 km southeast of the national capital Brasília (shown in Figure 1). The present day Paracatu mining operation, fully owned by Kinross Gold, through its Brazilian subsidiary Rio Paracatu Mineração (RPM) is designed to be the largest tonnage, lowest grade free milling gold operation in the world.The deposit currently hosts some 1.2 billion tonnes of ore at a grade of ~0.41 g/t gold, hence contains a total gold reserve of over 20 million ounces. At a designed plant throughput rate of 61 Mt/year the mine life goes beyond 2030."

Jan 1, 2011

By H. Kenworthy

This report concerns cooperative milling investigations of the Central mill of the Eagle-Picher Mining &. Smelting Co, The work carried on at the Central mill and the Rolla, Station shows that: It is possible to reduce the Central mill heavy-medium plant tailings by 0.05 to .15 percent zinc; the 3/16-inch to 10-mesh fraction of the jig feed can be treated by sink-float to obtain a tailing containing only half as much zinc as the jig tailing; Humphreys spiral concentration of the flotation tailing does not recover enough zinc to be economically attractive; and crushing and wet grinding of ferrosilicon for heavy medium are commercially feasible. The Eagle-Picher Co. operates extensive mines in the Tri-State area of Missouri, Kansas, and Oklahoma. The ore is milled at its Central hill, which also accepts custom ores. During the recent war the mill handled about 12,-000 tong- of low-grade ore per day. The company milled about 50 percent of the district tonnage and purchased nearly 90 percent of the custom ore. About 50 percent of the mill feed was from company mines. Zinc is the chief value in the Tri-State ores,-with Varying quantities of lead and cadmium minerals, as well as small amounts of germanium and gallium.

Jan 1, 1949

By A Golsby

Although much talked about, social licence to operate (SLTO) is a relatively new concept that has been deemed as one of the four biggest business risks to a mining project over the life-of-mine. There is no accepted single definition of SLTO and this author understands SLTO to be stakeholder perception of the legitimacy of a project, a company or an industry. At a specific site, and across different sites within the same organisation, SLTO ranges through different levels according to stakeholders’ degrees of acceptance in time and space. Management of SLTO is vital for the mining sector but is difficult as it is informal and intangible. Although there are no key performance indicators, there are certain indicators that enable relative measurement of the ‘level’ of the SLTO. Because of the importance of the SLTO, information management during the entire life-of-mine, from exploration to rehabilitation, becomes crucial for the continued operation of a project. This paper identifies ten basic principles for the management of information to support the SLTO.CITATION:Golsby, A, 2014. Managing information to support a social licence to operate, in Proceedings Life-of-Mine 2014 , pp 389–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J. Forwood

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the project's gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the Lenders' and Borrower's teams has facilitated a greater understanding and `ownership' of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

By Grey CA

Any economic evaluation of a lead-zinc mining project requires the estimation of net revenue per tonne of concentrate at the "mine gate". The value at the mine gate equals the Net Smelter Return minus all realisation costs. The paper develops a simple predictive model for Net Smelter Return based on metal prices.

Jan 1, 1990

By Wilson Blake

Rock preconditioning in advance of mining was shown to be an effective means of rock-burst control based on the results of a field demonstration carried out on the 7700 level of the Hecla Mining Company's Star mine. Mining through the preconditioned zone was characterized by greatly reduced rates of released seismic energy and no bumping or rock bursting occurred within the preconditioned zone. Mining above the preconditioned zone was characterized by greatly increased rates of released seismic energy and rock bursting, particularly where the vein became very narrow in waste zones. This increased incidence of rock bursting points out the need for stope preconditioning to be carried out on an entire stope block basis. The data obtained from the monitoring of the mining above the preconditioned zone on the 7700 level will be extremely useful in evaluating any future stope block preconditioning experiments on the lower levels or the Star mine.

Jan 1, 1980

NATURE OF ORETHE Edna May ore consists mainly of clean quartz of a moderately hard and tough nature. The gold content is "free" and fairly coarse, so that a large percentage is recovered by amalgamation. The ore is practically free from metallic minerals.GENERAL OUTLINE OF PLANT AND TREATMENTThe ore, received from underground in trucks, is broken by a jaw breaker, then stamp-milled, follow~d by partial filie-grinding in pans. Mercury is used both in the mill boxes and pans. The pulp, on leaving the pans, passes over amalgamating tables and is then elevated by tailings pulp to cone classifiers and separated into a sand and slime product, each product receiving a separate cyanide treatment-sand by leaching in vats and slime by agitation and decantation in a "Trent" plant. Gold solutions from both sand and slime are precipitated together by zinc shavings in the usual type of precipitation boxes. Accumulated slime is trucked from the dam to a vortex mixer and from this point receives with the cement slime the same treatment.ORE BREAKING AND TRANSPORTThe ore is trucked from the brace of the shaft along an overhead line to the breaker station. Hence it is, by means of a "kick-up" dumped upon a grizzly, set with 2-in. spaces, the oversize being broken by a 15 x '9 Fraser and Chalmer jaw...

Jan 1, 1919

By Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: ? Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; ? Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

Jan 1, 2007

By Hongyang Cao

The iron constituents selectively separated from the modified copper slags by magnetic separation and flotation.were studied. The results of magnetic separation for modified copper smelting slags show that the grinding size, current intensity and dispersant agent had great influence on grade, and recovery ratio of TFe in preparation concentrate; The results of flotation for magnetic concentrate show that the positive flotation of sodium oleate negatively upgrade the grade of magnetic concentrate, but the reverse flotation of lauryl amine and soluble starch are effective. The grade of TFe can reach 54% and the recovery ratio can reach about 90% in magnetic concentrate, when the grinding size is 45.8µm and the current intensity is 2.5A. The optimal effect is obtained by using lauryl amine as collector and soluble starch as depressant to reverse flotate magnetic concentrate, and the grade of TFe is upgraded 2.37%.

Jan 1, 2009