Search Documents

The formation and distribution of gold placers in active collisional mountain belts are directly related to the tectonic, topographic, climatic and erosional constraints prevailing on either side of the orogen at the time of placer formation. In the absence of pre-existing placer deposits, these factors combine to concentrate placer development on the side of the orogen facing the prevailing winds, where most of the erosion and uplift occurs. Drainage network changes and glaciation can significantly alter placer distribution with respect to source areas within the orogen. After collision stops, placer formation will proceed on both sides of the orogen as exhumation of the mountain belt ensues. Incorporation of pre-existing placers formed on ancient mountain belts into younger placers in subsequent orogens, may be recognised by anomalous placer distribution compared to the above model. Most of the relatively young giant placers such as those inNew Zealand, Chile, Bolivia and Columbia, exhibit these general patterns. Their character and mode of formation have important implications for the formation and distribution of much older placers, such as those in South Africa's Witwatersrand Basin.

Jan 1, 1996

The Golden Cross mine is a Joint Venture between Coeur Gold New Zealand Limited, as Manager, and Viking Mining Limited. The mine is targeting Zero Lost Time Accidents as a goal.   The Golden Cross operation produces gold and silver from both underground and open pit. The mine is based on an epithermal gold-silver deposit. Treatment of ore is on a campaign basis for each ore type (i.e. underground or open pit). Milling is conventional SAG Mill and Ball Mill grinding circuit followed by carbon in pulp recovery of gold and silver. All tailing materials are treated through the Cyanisorb process to reduce cyanide levels prior to being discharged into the tailings dam.

Jan 1, 1995

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By R N. Robson, A B. Christie, I J. Graham

Strategy development by the minerals industry identified the fragmented management of mineral resources as a significant impediment to the discovery and development of New Zealand Æs mineral resources. The total gross value of New Zealand Æs potential resources of coal and minerals is estimated at about $400 billion, but their potential value is not being realised. The management of minerals is now largely under the control of 86 local authorities (regional and district councils) and the lack of recognition of the significance of the sector has lead to inconsistencies in the way minerals are managed. The industry strategy influenced science funding for minerals, with the result that the 'mineral wealth' component now includes research on making better use of resource data in minerals management. Initially this research has targeted Otago and Northland regions where a number of initiatives are now in progress.   In Otago the Regional Council has budgeted to contribute $1 million towards a regional geophysical survey to advance mineral exploration and the management of subsurface resources in the region, to work cooperatively towards improving public awareness of the significance of minerals to regional economic activity, and to better coordinate policy-making for minerals at regional and district levels.   Crown Minerals, and the Far North and Whangarei district councils are considering providing funding support for an economic study of the mineral potential of Northland, building on a mineral resource assessment undertaken by GNS Science. Enterprise Northland is adding minerals to their list of potential growth sectors, and is supporting the operation of a Northland region minerals focus group.   Regional development agencies and local authorities have shown that they are willing to include mineral resources in their development strategies and to provide for them in policies and plans when supplied with information and assisted with technical support.

Jan 1, 2006

By James Westfield

Following is a brief resume of the Division's activities that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1961

By Enrique Hermana, Raymond F. Dalton, Raymond Price, Barry Hoffman

Introduction Chloride leaching of sulfidic ores has been known about for 100 years. It is recognized as a highly efficient process to produce concentrated leach solutions. Despite this, chloride leaching found little practical application until recently because of the highly corrosive nature of concentrated chloride solutions. This situation changed with the advent of modern construction materials such as GRP, polypropylene, butyl rubber, etc. And in the past 20 years, research has burgeoned in the area of chloride hydrometallurgy. The research impetus stemmed from the belief that chloride leaching can provide an alternative to smelters for treating conventional copper concentrates. In addition, chloride leaching was thought to be suitable for on-site refining of copper at small tonnage operations located in remote areas. And chloride leaching was seen as a logical choice for treating unusual or complex concentrates that smelters could not handle. Underpinning these beliefs is the attraction of chloride-based hydrometallurgical processes for sulfidic ores. Sulfur is liberated in the environmentally acceptable elemental form rather than as sulfur dioxide. Consequently, sulfidic copper ores have received much attention. A review of Edmiston in 1984 describes 12 chloride-based processes. All managed to progress past the "laboratory beaker" stage of evaluation. In nine of these processes, copper is recovered electrolytically. Key features of these processes are summarized in Table 1. Table 1 shows that the processes must include a copper solvent-extraction step. Only these processes produce a clean copper electrolyte capable, with no further refining, of directly producing high quality cathode copper. The ICI/Elkem process is the exception here. The rest of these processes use o-hydroxyaryloxime reagents for the solvent extraction of copper and are constrained by the performance of these reagents. This is governed by hydrogen ion concentration (Equation 1). The practical result is that only relatively dilute copper solutions can be treated (Canmet, Phelps Dodge), or careful pH control or adjustment is necessary (Minimet Recherche, B.H.A.S.). This negates one of the attractive features of chloride leaching - its ability to produce very concentrated copper solutions, up to 40-45 gl-1. [ ] In all four processes using o¬hydroxyaryloxime extractants, solvent extraction transfers the copper from the chloride to the sulfate medium. To minimize cross-contamination of the two anions, the loaded organic solvent has to be scrubbed to remove the chloride ion. This represents an additional complication in the solvent extraction circuit. And it

Jan 1, 1988

The design of a mine should aim to optimise the market value by maximising revenues whilst minimising costs. In open pit mining, the nature of the extraction technique translates this objective into the maximum recovery of reserves while minimising waste extraction subject to technical, economical and safety constraints. Since the introduction by Lerchs and Grossman, in 1965, of a model that is now considered a classic in the area, open pit design has reached a level of maturity and acceptance by industry. These models are being used on a regular basis by designers and planners.This paper proposes a new alternative model for open pit design. It is based on genetic algorithms (GA) and exploits a reduction of the number of decision variables of the more traditional techniques. The novel approach provides more flexibility than traditional models; it can also be extended to consider planning problems that traditional open pit design models are not capable of handling. The algorithm has been designed for two dimensional problems and tested in a simple instance. The results obtained in this simple test are encouraging and are a good supporting argument for the development of a GA model capable of handling three-dimensional (3D) instances. The model presented in this paper is just a first step towards a full GA to solve the pit design problem and it is believed that novel tools like the one presented herein could become great allies in tackling challenging problems in open pit design, an illustration of such a challenging problem is presented and discussed.

Dec 6, 2010

By K. Kotwica, P. Gospodarczyk, J. Sosnica, J. Pawlik, Z. Iwulski, K. Pawlik

The paper presents problems resulting from the mobile mining machines functioning and requirements concerning a machine control system, which controls successive operation stages of such machines. The problem is presenting on the example of a mobile hydraulic support to remove residual pillars in copper ore mines. The paper describes an algorithm and a flow chart to be followed when designing a supports control system. Design of control systems to ensure machine function under given circumstances is also presented.

Jan 1, 2003

Comparison of Grinding and Liberation Processes for Stalky Biomass Materials as a Prerequisite for Production of Energy Pellets with High Calorific Value Pelletising biomass, especially straw and stalky materials, requires a product specific size reduction and liberation. However, moisture content plays an important role in palletising and also affects the energetic properties of the biomass. The paper illustrates the characteristics of the mentioned type of biomass and specifies the necessities for production of energy pellets. Defined requirements for biomass energy pellets will be shown based on relevant standards. The work focuses on a comparative investigation of the straw fibres after grinding with hammer/impact mill and after the liberation of the straw fibres with twin-screw extruder (two different communition units). A traditional hammer mill as well as an hydrothermal process taking place in a twin-screw extruder were utilised. Results of the grinding and liberation of rye and wheat straw fibres are discussed based on a detailed particle characterisation (particle size and shape distribution). Besides high calorific value the main pellet quality parameters are mechanical stability, abrasion resistance and further combustion technical characteristics. The particle size distribution displayed optimum characteristics for the combustion processes to be carried out in a furnace. The durability of the pellets produced from straw fibres liberated with twin-screw extruder was comparatively better then that prepared with the straw fibres after grinding with impact mill. Particle size distribution, abrasion values and the strength characteristics showed a good correlation with each. The high presence of N and S would result in high NOx and SOx emissions, where as the high concentrations of Cl would corrode the furnace. These chemical properties of the straw would restrict its usage in small scale furnaces.

Sep 13, 2010

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

By M. Sanchez, C. Morales, J. Palacios

The slag produced in the Peirce Smith converters at the Ilo smelter of Southern Peru Copper Corporation has shown a wide range of magnetite content, which introduces an additional problem in the smelting units due to materials? recirculation. However, the operation data analysis and the application of thermodynamic concepts have made it possible to produce slag with magnetite content between 18 and 20%. The results have suggested that matte grade enhances magnetite formation while silica controls its precipitation, and they are also influenced by the increasing temperature of the slag. Thus, in order to obtain the required magnetite content in the slag, matte grade is gradually enriched in equilibrium with slag containing from 25 to 32% silica.

Jan 1, 2004

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By J. Janssens, B. Coletti, S. Smets, J. Plessers

The oxygen activity of the ladle slag determines the reactivity towards the steel during ladle treatment. Therefore, the in situ measurement of the oxygen activity of slags can be an important tool. The applicability of an electrochemical sensor is examined in this work. The sensor measures the electromotive force (EMF) that is established between a sample of the slag phase that is immersed in the liquid steel bath and a reference system (Cr/Cr2O3). Industrial and laboratory experiments demonstrated the capability of the sensor to detect the influence of the slag components on the measured oxygen potential. Comparison of the measured values with thermodynamically calculated values shows that the measured oxygen activity is systematically too low. This was attributed to a reaction of the steel with the slag sample. To investigate this, further lab tests were performed where the slag oxygen activity was measured after the slag had been equilibrated with the steel. The measured values were dependent on the oxygen activity (aO) of the steel. For industrial applications, it is concluded that the aO of the steel should be known and that this value is necessary for the interpretation of the measured values. Keywords: low carbon steels slags, slag oxygen activity, on-line sensing, thermodynamic evaluation.

Jan 1, 2004

By A. K. Bhattacharya

Cylindrical bridge piers are widely used and equations exist that can predict the maximum depth of local scour around such piers. Scour around piers is an undesirable phenomenon, as it requires the foundation to be placed to a greater depth resulting in increased cost, making it worthwhile to investigate scour-reducing measures. A number of scour-reducing measures have been tried out for cylindrical bridge piers including placing a concrete collar around the pier, having a delta-wing projecting upstream in front of the pier, placing riprap around the pier, using a group of piers instead of a single pier, having a slot in the pier aligned in the longitudinal direction. The objective of this study is to investigate the effect of upstream protective piles on reduction of maximum local scour depth around a cylindrical bridge pier. The upstream piles are placed at different radial distances in front of the pier and the scour depths are observed. The proposed equation of Dey (1997) for determining the maximum depth of scour around a cylindrical bridge pier is used. The reduction of local scour around the pier is compared with local scour around an unprotected pier.

Jan 1, 2009

By K. K. Kershner

The purpose of this investigation was to develop methods, on a laboratory scale, for recovering tin from Bolivian metallurgical slimes. Petrographic and chemical analyses were made of slime ore fractions from several well-known tin operations. High percentages of the total tin were volatilized as chlorides at temperatures below 600° C. Under optimum conditions reaction rates were relatively rapid, and the chloridizing reaction approached completion. Owing to the low temperatures involved and the high yields of tin, the process was considered to have possibilities for treating Bolivian slimes on a commercial basis. ACKNOWLEDGMENTS Appreciation is hereby extended to the Patino Mines and Enterprises, Inc., of Bolivia, for supplying slimed tin ores that were used in the experimental work. This company has since been nationalized.

Jan 1, 1959

By Manuel Sanchéz

Para las empresas mineras, la búsqueda de buenas condiciones con los clientes y la optimización de los procesos involucrados en la cadena de valor, es uno de sus principales objetivos. En este sentido, el presente texto señala las estrategias y soluciones que priorizen y mejore la calidad de las decisiones en la empresa.

May 25, 1998

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962

By Bruce Hebblewhite

Australia’s Minerals Tertiary Education Council (MTEC) has achieved several successes during its first three years of operation. This initiative was developed through the Minerals Council of Australia, in conjunction with three partner universities involved in mining engineering education. The partner universities are the University of New South Wales (UNSW); Curtin University, the West Australian School of Mines (WASM); and the University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and the development of a number of flexible, distance-based delivery programs. This article then discusses future initiatives. Importantly, the challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering: Mining Education Australia (MEA). This will provide a common third and fourth year program to all three universities beginning in 2007. The common program will involve innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process.

Jan 1, 2006

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

By Henri F. Letient

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid mine drainage and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings towards the end of the mine life, thereby generating a non-acid generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-acid generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid generating rock and to be flooded at the end of mine life.

May 1, 2002