Search Documents

By M. Nduna

Surface properties of metal sulphides have a great significance in various areas of engineering and science, such as acid mine drainage, contaminant sorption, and metal separation. In various attempts at producing metal sulphide particles from synthetic solutions, prodigious quantities of nuclei that grow only to colloidal dimensions have been frequently reported. This copious nucleation is promoted by the high levels of supersaturation that characterize most precipitation reactions. Colloidal particle formation in precipi¬tation-based separation processes results in sub-optimal solid-liquid separation, which is alleviated by the production of more highly crystalline particles or agglomerates. The current work approaches this challenge from an electrochemistry perspective, by measuring surface charge potential of precipitant particles during metal sulphide precipitation with respect to the concentration of metal sulphide lattice ions in solution. Electrophoresis was used to measure the metal sulphide particle zeta potential and the settling properties were obtained by performing settleability measurements using an Imhoff settling cone. A suspension of copper sulphide particles was precipitated from synthetic solutions of copper and sulphide ions at equimolar concentrations. Immediately after precipitation the copper sulphide particles had a zeta potential of -50 mV and a settleability of about 7 ml.l-1. With the addition of copper ions the settleability increased by a factor of nearly three times and the zeta potential also increased to a maximum of -40 mV. A decrease in zeta potential to a minimum of -60 mV was observed after the addition of sulphide ions and this was associated with a settleability of 0 ml.l-1.

Jan 1, 2013

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By Winton J. Gale

Coal pillar design has been based on generalized formulas of the strength of the coal in a pillar and experience in localized situations. Stress measurements above and in coal pillars indicate that the actual strength and deformation of pillars vary much more than predicted by formulas. This variation is due to failure of strata surrounding coal. The pillar strength and deformation of the adjacent roadways is a function of failure in the coal and the strata about the coal. When the pillar is viewed as a system in which failure also occurs inthe strata rather than the coal only, the wide range of pillar strength characteristics found in the United Kingdom, United States, Republic of South Africa, Australia, People's Republic of China, Japan, and other countries are simply variations due to different strata-coal combinations, not different coal strengths. This paper presents the measured range of pillar strength characteristics and explains the reasons. Methods to design pillar layouts with regard to the potential strength variations due to the strata strength characteristics surrounding the seam are also presented.

Jan 5, 1999

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By C A. Locke, A B. Christie, J Cassidy, J L. Mauk

New and existing gravity and aeromagnetic data are used to determine the structure of the Waihi region and to investigate any relationship between structure, hydrothermal alteration and epithermal mineralisation. The 24 mGal, 10 km diameter, negative Bouguer gravity anomaly which occurs south of Waihi has been modelled as a I.5 km deep asymmetrical basin. This basin, the Waihi Depression, is interpreted to be infilled with low-density volcanic rocks of the Uretara Formation and Whitianga Group, overlying older andesites of the Waipupu Formation. To the north and west, the margins of the depression are defined by the Waihi and Mangakino Faults, which have been modelled with dips of 45 - 60¦ to the south and west respectively. The southern and eastern boundaries of the Waihi Depression are defined by smooth, shallow dipping (15 - 20¦) boundaries. The Waihi Depression is interpreted as a fault-angle depression, resulting from southeast extension in the early Pliocene. The Waihi Fault is modelled as an approximately E-W feature, located to the south of Waihi. Small 2 - 4 mGal positive Bouguer gravity anomalies occur north and west of the margins of the depression, and correlate with known areas of hydrothermal alteration and areas of low magnetic gradient.

Jan 1, 2003

By Issa S. Oweis

Limestone is a sedimentary rock composed primarily of calcite (calcium carbonate). In the presence of an aqueous solution of carbon dioxide (carbonic acid) bicarbonate radicals (2HCO3)- are produced that are highly soluble. The same type of reactions occur in terrains where dolomite (calcium magnesium bicarbonate) reacts with carbonic acid to produce highly soluble bicarbonates (4HCO3)-. The source of carbon dioxide is the small content in rainfall but to a large extent from the organics in the soil. The solution activity depends on many factors including the content of carbon in the rock, acidity of soil water, groundwater velocity and other factors. The resulting features are referred to in literature as sinkholes, solution channels, caves, karstic topography, and cavernous limestone. The presence of solution features affect the shafts in several ways: (a) the shaft resistance is affected by voids along the shaft, (b) concreting of the shaft should consider the presence of voids along the shaft, and (c) the shaft base may be in close proximity to a solution feature that may cause future collapse under structural loads. Methods to mitigate such effects include verification of rock to below the base (vertically and laterally). Cavities are stable by virtue of arching in the rock. Under the action of end bearing from a shaft, the arch may collapse depending on its proximity to the base of the shaft and the strength of the rock. This paper focuses on this issue. Finite Element analyses are conducted to relate shaft end load and bearing area that will produce failure based on given rock properties, size and location of cavity. Failure is defined as settlement of the base equivalent to 5% of shaft socket diameter. The software Plaxis is used for analysis. The rock is considered as c-f material derived based on Hoek-Brown failure criteria (2002 edition) that is based on Geological Strength Index (GSI).

Jan 1, 2009

By A. V. Pavlov, A. V. Dubachev, K. L. Kossyrev

The purpose of the given research was to investigate the possibility of high-carbon ferrochromium refining to remove harmful impurities as a result of metal treatment by slag mixtures on the basis of the CaO-MgO-SiO2system. The final conclusions were drawn from experimental results. It was shown that the treatment of high-carbon ferrochromium by SiO2-MgO-CaO slag mixtures with additions of chromium sinter or iron-ore concentrate removes carbon, sulphur and phosphorus from the metal. A mechanism of phosphorus removal from a melt to a gas phase is proposed.

Jan 1, 2004

By A. M. Tonnos

Underground mining has yet to see an industry wide solution for control of their ventilation systems due to the complexity and sensitivity of the underground environment. Complexity arises from multi-level, multi-zone operations and sensitivity is associated with the impact that changes in equipment status and output have on air flows and quality throughout the mine. Our approach to solving this challenge incorporates system modeling and industrial control systems in a unified architecture. Although this approach can be applied to other processes and industries, this paper will cover the theoretical and practical aspects of an integrated model-control system (MCS) as it applies to underground mining ventilation.

Jan 1, 2009

By F. Haessner, M. Wilkens, U. Jakubowski

ThOUGH at present there is a wide range of possibilities for the quantitative determination of preferred orientations, pole figures of identical specimen material have not been determined by different methods as yet.''' In this paper a comparison of (Ill), (200), and (220) pole figures is presented which were obtained from a 95 pct cold-rolled high-purity cop- per sheet (99.9998 pct Cu), by three different methods. The three methods are: a) The combined X-ray reflection-transmission technique of plane samples by schulz3 and Decker, Asp, and Harker. 4 A Siemens texture goniometer was used. The experimental details are described elsewhere. 6 b) The X-ray reflection technique of spherical samples by Jetter and Boric.' A Siemens texture goniometer with some modifications was used. The samples were prepared by sticking 140 polished sheets together with an adhesive and machining a sphere (20 mm diam).* Additional

Jan 1, 1967

GE Industrial Systems has received a multimillion dollar contract from Bucyrus International to supply complete electrical systems for three new draglines. These machines will be installed at Coal India’s Northern Coalfields’ Dudhichua and Nigahi open cast mines. The Dudhichua and Nigahi mines are located south of Varanasi. They produce Type C and Type E coal for use in the region’s super-thermal power stations. The GE systems will power and control the drag, hoist and swing motions of one Bucyrus W2000 walking dragline at Dudhichua and two a Nigahi.

Jan 1, 2000

By M. Kinne

Catalyst preparation/ characterization Slightly modified DP (~Schumacher et al. Catal. Lett. 89, 109, 2003) CeO2 HAS 15 from Rhodia calcined in air for~ 2h BET: ~188m2/g, particles size: 5.7nm (TEM, XRD) + HAuCl4 at pH of 6.5-7, (>95% of the Au was deposited) ? Au/CeO2 (2.6wt% Au, ICP-AES) A new conditioning procedure was applied, including heating at low temperature in N2 and H2/N2 mixtures) Patent DE 10205873A1. Very small Au particles <2nm, for CO oxidation catalyst as Au/TiO2, Au/Fe2O3, and Au/Co2O3 Here Au particles size <3.5nm (XRD) Summary ? CO is nearly exclusively adsorbed on the Au particles ? Positive reaction orders of 0.5 are found for CO and H2O ? Ea= 40kJ/mol ? The catalyst is very active and stable ? During WGS reaction huge amounts of formates are formed and cover the surface ? The activity of the catalyst seems to be correlated with the formate species.

Oct 1, 2003

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By M A. Tuck

The dominant heat loads in a deep underground mine are the surrounding rock mass, autocompression and machinery. In addition heat can be contributed to by other sources. Many block cave, sublevel cave operations and coalmines utilise conveyors to transport broken rock out of mine, in some cases completely, in others in combination with other forms of transport. This broken rock can be loaded onto the conveyor at virgin rock temperature and can represent a major heat input to the ventilation airflow as it is transported out of the mine. The purpose of this paper is to review established knowledge regarding heat flow, from conveyed rock to determine the main factors influencing the heat flow and to develop a methodology for predicting heat flow from caved rock. The paper concludes with suggestions for further research in the area of conveyed rock heat transfer.CITATION:Tuck, T A, 2017. Accurately estimating heat load from conveyed rock, in Proceedings Australian Mine Vent Conference 2017, pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By M. Schafer

The 20 foot diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT-3) has been completed. This paper will summarize aspects of liner design and address the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented.

Jan 1, 2008

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

By L J. Ingle, K L. McPhee, A G. Hunt

Iron Road Limited (IRD) is currently developing the Central Eyre Iron Project (CEIP) at Warramboo on the Eyre Peninsula, South Australia. The project consists of a 30 year open pit mine, magnetite processing facilities, standard-gauge railway and deep water, Cape class capable port. Major South Australian government approvals have been received and funding arrangements confirmed.The 4.5 Bt Mineral Resource (3.7 Bt Ore Reserve), the largest in Australia and among the largest globally, is to be mined to produce 24 Mt/a high-grade, 67 per cent Fe, magnetite concentrate. This in-demand, premium product has a P80 of ~100 &#181;m, suitable for both direct sinter feed and an additive in pelletising.The extensively drilled, homogeneous orebody is unique in both geology and mineralogy; only averaging 15 per cent Fe yet coarse-grained with almost negligible phosphorus and sulfur content. This has allowed significant opportunities to tailor the mining method to the orebody, utilising both optimised blasting as first stage comminution, as well as in-pit crushing and conveying (IPCC) to reduce the heavy haulage diesel fleet and optimise the pit shell.Approximately 1 Mt/d of total material, ore and waste, is required to be moved from the pit daily, introducing materials handling challenges, overcome by a flexible IPCC set-up, multiple overland conveyors and an exacting mine plan. Non-conventional waste and tailings storage is utilised to allow for significant water savings, progressive rehabilitation and minimisation of land impact.The processing facilities utilise both the magnetic and density properties of the magnetite to beneficiate the ore. The coarse-grained nature of the ore is exploited to minimise comminution yet still liberate a high quality product. Utilisation of modular construction methods allows risk reduction during construction and reduced pumping requirements during operation.This paper highlights the uniqueness of the CEIP, with focus on the mineralisation of the orebody, and the beneficial impacts this has on both the proposed mining method and processing. Magnetite mining is not new and IRD has used the learnings of others, and input from various vendors and industry experts, utilising knowledge and expertise to engineer an innovative, yet supported, project design.CITATION:McPhee, K L, Hunt, A G and Ingle, L J, 2017. The Central Eyre Iron Project – developing a new iron ore mine in a challenging climate, in Proceedings Iron Ore 2017, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Ray E. Harris

Introduction A resource of more than 122 Gt (134 billion st) of minable trona and mixed trona and halite underlies an area of about 3400 km2 (1300 sq miles) west of Green River, WY (Culbertson, in preparation) (Fig. 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6 Mt (6.7 million st) (Kostick, 1983). About 90% of this came from Wyoming trona. This enormous deposit occurs in the Wilkins Peak Member of the Green River Formation that is of Eocene age. This formation is derived from sediments deposited in a large lake named Gosiute. Lake Gosiute occupied the Green River Basin in southwestern Wyoming some 38 to 54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition when the trona deposits were formed. A total of 42 trona beds are known. Of these, 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation). The production of sodium compounds from the trona deposits in the Wilkins Peak Member began in 1896 when wells were drilled within the present boundaries of the town of Green River. The purpose of the drilling was for extraction of sodium carbonate brines. Sodium carbonate (sal soda) was removed from these brines at a plant in Green River. Bedded trona was discovered in 1938 in a core from an oil well drilled south of Westvaco. In 1947, the underground mining of trona began. Production has continued from 1948 to date. Currently, five companies are mining trona and producing soda ash from the Wilkins Peak Member in Wyoming. Additionally, Allied Chemical Co. mines and processes trona for Church and Dwight&apos;s sodium bicarbonate (baking soda) operation in Green River. Competition in the soda ash industry depends primarily on the efficiency of mining and refining, allowing for lower-cost production. Newer plants and mine designs should increase efficiency. Solution mining holds promise as an even lower-cost method of mining. Employment in the soda ash industry is declining since the newer mining and refining methods are less labor intensive. Declines in employment, however, may be offset as production increases. Due to the large resource, the availability of minable trona should not be a problem for perhaps hundreds of years. Geology of Wyoming trona deposits Forty-two beds of trona or mixed trona and halite occur in the

Jan 10, 1985

By N. Krauland, A. Nystrom, M. Board, S. Sandstrom

Several deep Swedish cut-and-fill mines experience severe ground control problems, including roof collapse and wall sloughing, as a result of variable rock quality and high in situ stresses. A project to examine the problem included two main areas. The first was prediction of mining conditions at depth and the adaptation of cut-and-fill mining to such conditions; the second was the assessment and improvement of support methods at present and future depths. Simple, elastic, mine-scale numerical models were used to optimise stope sequencing and more detailed, stope-scale models to simulate the failure processes around a stope and the interaction of rock mass and support. Kristineberg was chosen for testing and calibration of the predictive methods because of its long history of severe ground conditions and the large base of observational and monitoring data available for comparison. Horizontal cut and fill was found technically suitable to depths beyond 1 000 m and economically viable if ore value covers support costs. Stability can be achieved with the present support technology down to 1 000 m but the 7-strand 15.2 mm cables have poor deformation properties (5% failure strain) compared with rebar rock bolts (17%). Reducing the intervals between levels from 100 m to 50 m will cut support costs and improve production reliability and capacity. Simulation of sill-pillar mining indicated that conditions would be most severe when pillar height was reduced to 15-20 m; mining of a sill pillar has been carried out successfully to the last 3 m, whose extraction is planned for the near future

Dec 1, 1995

By S. Lubbe

South Africa and Australia are the biggest suppliers of zircon sand to the international zirconium industry. However neither South Africa nor Australia is well known for zircon beneficiation. Geratech Zirconium Beneficiation Ltd (GZB) continued with additional research on sodium hydroxide (NaOH) cracking of zircon sand during 2002-2003. In 2003 GZB started extracting zirconium from zircon sand by means of NaOH cracking on a commercial scale. Experience has shown that temperature profile and atmospheric control inside the furnace is crucial for the beneficiation of zircon sand. Silica carryover to zirconium chemicals could result if a high temperature is used. Once the sodium silicate is extracted from the sodium zirconate and dissolved in hydrochloric acid, two distinct routes can be followed to precipitate various zirconium chemicals. The most common route is to precipitate zirconium oxychloride crystals (ZOC), with subsequent purification from all contaminants (crystal route). Less known is the process (liquid route) that involves the direct precipitation of zirconium basic sulphate (ZBS). This route will yield a less pure product, with contaminants such as silica and titanium. An important factor in this route is the prevention of silica gel formation, which could hamper final product filtration. For applications like paint drying (zirconium octoate) or antiperspirants (zirconium hydroxychloride) low levels of contaminants have no effect on the final product. The advantage of the liquid route is fewer production stages compared to the crystal route. The disadvantage of the liquid route is that the market for the products will be significantly smaller. The optimum solution could be a plant design that could cater for both routes. Another example of an application of zirconium chemicals is the use of ammonium zirconium carbonate (AZC) in the paper industry. Zirconium basic carbonate (ZBC) is dissolved in ammonium carbonate to produce AZC solution. AZC is used mainly in European countries in the paper industry. For example, carton boxes were initially produced with formaldehyde as the binder, however, it has now been replaced with AZC since formaldehyde is considered toxic. AZC reacts with the cellulose fibres in the paper to act as the binder. The resulting product is not toxic, and printing ink dries very quickly due to the porous paper structure. Other applications of zirconium chemicals involve the use of acid zirconium sulphate tetrahydrate (AZST), zirconium orthosulphate (ZOS), potassium zirconium carbonate (KZC), and zirconium hydrous oxide (ZHO). Fluoride-based zirconium chemicals like zirconium tetra-fluoride (ZrF4) and hexafluoro-zirconic acid (H2ZrF6) are used in the aluminium industry. Zirconium oxide (Zr02) can be produced from any of the abovementioned precipitated chemicals via a high-temperature decomposition process. The physical properties of such oxides can differ tremendously, depending on the final application. The fired density of sanitaryware is typically 5.8 g/cm3, compared to milling media at >6.1 g/cm3. The required fired density is achieved by controlling the precipitation and decomposition conditions for these two oxides. The same applies to stabilized and mixed oxides, for example where zirconium oxide acts as an oxygen carrier in fuel cells.

Jan 1, 2012

By Arthur L. Holloway, James C. Mugford

"The Underground Research Laboratory (URL) is located in southeastern Manitoba, in the Lac du Bonnet granite batholith of the Canadian Shield. It was constructed by Atomic Energy of Canada Limited (AECL) to conduct geotechnical research for the Canadian Nuclear Fuel Waste Management Program, assessing the concept of permanent disposal of nuclear fuel waste deep in plutonic rock.One of the primary objectives of the research program at the URL is to develop a nondestructive rock mass characterization method that can be used during siting, design and construction of a used fu el waste disposal vault. An experimental program was established to assess radar reflection profiling as a technique for fracture characterization in granite. The highly resistive, homogeneous nature of the Lac du Bonnet granite is ideal for the propagation of electromagnetic energy at the radar range of frequencies and water-filled fracture zones act as excellent reflectors because of their contrasting electrical properties.Radar reflection profiling was undertaken to characterize a major fracture zone located between 5 m and 10 m below Room 211 on the 240 m level of the URL. The profiling was done at a frequency of 120 MHz, on a 1m grid laid out on the bare rock floor of the room. Reflectors identified in the analog data were correlated between the profile lines, digitized, and a three-dimensional surf ace for each recognizable reflector was constructed. These surf aces were then compared with data obtained from the examination of numerous cores from adjacent boreholes intersecting the fracture zone. A very good correlation was found between the major radar reflectors and the most intensely fractured regions of the zone. Modelling studies also showed that a series of prominent shallow radar reflectors were caused by a borehole drilled close to Room 211."

Jan 1, 1990