Search Documents

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By M. J. Ferrante

The preparation and subsequent reduction of vanadium trichloride was investigated as a process for the production of high-purity vanadium metal. Chlorine was reacted with vanadium oxide in the presence of carbon to vanadium tetrachloride. The contaminant vanadium oxytrichloride was also formed and later converted to tetrachloride by reaction with chlorine in the presence of activated charcoal. Vanadium tetrachloride was stirred continuously during thermal dissociation to vanadium trichloride powder from which volatile contaminants were removed by distillation. The vanadium trichloride powder was reduced to vanadium sponge by controlled feeding of the trichloride into molten magnesium. Excess reductant and byproduct salt were removed from the vanadium sponge by high-vacuum distillation. Batches as large as 6.5 kilograms of sponge metal were prepared at an average reaction efficiency of 98 percent. Vanadium sponge after consolidation by arc-melting contained 820 to 11330 ppm of interstitial impurities and had a hardness between Rockwell B 40 and 70, This metal exhibited excellent workability at room temperature. The purification of impure vanadium metal by electron-beam melting resulted in lowering interstitial impurities from 1,890 to 504 ppm and hardness from Rockwell B 87 to 28.

Jan 1, 1968

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By M. Sanchez, I. Imris, G. Achurra

The Smelting and Converting El Teniente Process for copper concentrates as well as Slag Cleaning Furnace Technologies to treat slags coming out from the El Teniente Furnaces are widely applied today in Chile and around the world. Several industrial applications of this process have shown their capability to treat copper concentrates in a wide range of chemical and mineralogical compositions. Main operational parameters determining performance of the process are: oxygen enriched air flow rate, degree of oxygen enrichment, moisture content of the solid materials processed, molten material levels inside the vessel, frequency of molten materials tapping, bath temperature and copper losses in slags. In this work, the copper losses in the slags from El Teniente pyrometallurgical process are predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and slag industrial data. Results obtained show that the main part of copper losses in the slag from El Teniente Furnace are mechanically entrapped or floated unsettled droplets of the coexisting matte phase. by the contrary the very low copper losses in the slag from slag cleaning furnace are limited by the physico-chemical form.

Jan 1, 2004

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sub) coal which may be mined when the better deposits are depleted.

Feb 24, 1997

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By Robert B. Parsons

"The Canadian mining industry is not off to a good start in the 1993/94 budget season. Of the five provinces and territories to table budgets as of March 31, 1993, the industry's scorecard shows: one win, one tie, and three losses.IntroductionBy the end of March, five of Canada's twelve provincial and territorial governments had tabled their 1993/94 budgets. The mining industry is off to a bad start. The industry's scorecard shows one win, one tie, and three losses. Only Newfoundland appears to be paying any attention to the industry's concerns about the impact of taxation on competitiveness. It is particularly disconcerting to see that non-profit based taxes continue to increase, at a time when these taxes are the focus of a united attack by the entire industry.NewfoundlandFirst, the good news. On March 18, 1993, Finance Minister Winston Baker announced the following changes to the province's mining tax regime:"

Jan 1, 1993

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By Kenneth B. Higbie

METALLURGICAL ACTIVITY in 1963 was again dominated by the insatiate demands of research and development conducted in conjunction with the nation's defense and aerospace programs. An increasing effort was noticeable throughout the year, however, to apply to the commercial field many of the processes and techniques that have been developed by government-sponsored research. Particularly effective has been the Industrial Applications Program of the National Aeronautic and Space Agency through which many of the technological advancements made during the course of NASA research and development have been published and released to the public. POWDER TECHNOLOGY Powder metallurgy techniques for fabricating metals, not long ago declared outmoded because of improved casting and shaping methods, have since made an astonishing comeback. Traditionally mechanical pressing of powder shapes has been employed when melting and casting was difficult or impossible, when phase relationships needed to be sidestepped, or when machining costs could be avoided. Hence, it has long been used for producing relatively small special shapes of high-melting metals and alloys. Small iron parts produced with a punch and die have been common for many years, but powder metallurgy techniques are now applicable to a wide range of materials and items. Hard-to-handle materials including refractory metals and their alloys are now rolled, forged, or extruded from billets made by sintering isostatically compacted powders. The major element of the powder metallurgy industry still comprises iron shapes, however, and two-thirds of the annual 100,000 tons of powder metallurgy products are made of iron. The largest single user of powder-forming techniques is the automobile industry which currently consumes 14,000 to 16,000 tons of iron powder per year. A typical 1963 model auto contained more than 100 pressed powder parts (e.g., transmission gears, timing gears, sprockets, ball joint suspensions) totaling 5 to 7 pounds per car. Some of these powders are used in self-lubricating parts of porous copper and copper alloys containing as much as 20 volume-percent lubricating oil. The expanded use of powder techniques, coupled with

Jan 1, 1964

By K. P. V. Lei

The Bureau of Mines investigated molten-salt electrorefining as a practical method for reclaiming vanadium from vanadium scrap. An electrolytic process utilizing a KC1-LiC1-VC12 electrolyte at 615° C was developed for producing ductile vanadium with a purity over 99.9 percent. The recovery of the vanadium in the cell feed ranged from 88 to 93 percent with a current efficiency from 83 to 95 percent.

Jan 1, 1967

By H Firdausi, I Pasek, T Chenier

The Grasberg Block Cave (GBC) Mine is one of the future underground mines of PT Freeport Indonesia (PTFI). Located in the remote highlands of Papua, Indonesia, the GBC mine is scheduled to start production in 2017 reaching its peak production capacity of 160 000 t/d in 2023.In order to reach planned production capacity, the GBC mine will utilise an ore handling system consisting of rail haulage, crushing and conveying. The rail haulage system will utilise over 20 km of track while crushing is accomplished by way of three gyratory crushers each with a capacity of 3300 t/h. Nine conveyors operating in two parallel systems, each system over 3 km in length, will move the ore from the crushers to the stockpiles. These systems require a network of larger tunnels and mass excavations to accommodate the planned production facilities.This paper will describe the ore handling system, tunnel and mass excavation methodology as well as some of the challenges encountered with ground conditions and excavation quality during the execution of the project. A combination of lateral and vertical development methodologies and equipment, including drill jumbos, mechanised raise climbers and specialised ground support equipment, have proven successful in the development of a quality ore handling system.CITATION:Pasek, I, Firdausi, H and Chenier, T, 2016. Development of the ore handling system at the Grasberg block cave mine, Indonesia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. D. Lowell, L. Quevedo

I will talk today about a porphyry copper exploration program now underway in the Amazon jungle in the southeastern part of Ecuador near the border with Peru. The project is unusual for two reasons: first the deposits are of Jurassic age, 153 m.y.o., which is unusually old for porphyry copper deposits and they may be the most significant pre-Tertiary age porphyry deposits known. Second, the district was found only six years ago which makes this the most recent discovery of a totally new porphyry copper district. The new porphyry district, known as the Zamora River Copper Belt, or the Corriente Copper Belt, is a north trending area 50 km long by 10-15 km wide, which is nearly aligned with the axis of the Jurassic age Zamora batholith and with the course of the Zamora river. Gencor in 1994 initiated a regional grassroots gold exploration program based on reconnaissance geologic mapping and geochem sampling which did not find a gold mine, but which identified the San Carlos porphyry copper system in April, 1995. In a later reorganization between Gencore and Billiton the Ecuador project was transferred to Billiton and between the Gencore work and Billiton’s a total of 10 porphyry copper systems were found over the next four years. In the period of 1997 - 1999 Billiton drilled a total of 11,000 meters of wide spaced core holes in the San Carlos, Panantza and Kutukus prospects. In October 1999 Billiton concluded a farm-out, joint venture agreement with Corriente Resources and Lowell Mineral Exploration for additional exploration of the Zamora property. This is funded by Corriente and managed by Lowell Mineral Exploration and a total of 28,000 m of core drilling was completed through August 2001. An immediate result of the Corriente Lowell project was the discovery of potentially commercial ore reserves in two new deposits at Mirador and Warintza. Additional closer spaced drilling was done in the Panantza deposit and additional drilling is planned at San Carlos, in targets related to Warintza, and elsewhere.

Jan 1, 2002

By Claude Cunningham

Ths oonoept of precise. eooursts timing with Elsotronic Delay Detonators (EDD’s) was first ssriously sddresssd in ths mid 80’s end much wss made of the cheapness end profusion of digital wstohes in terms of the likelihood of EDD’s also being cheap and essyto produce. Ten years Iater. with every major explosives group end many elsotronios groups having instituted projects to capitalize on the promise of these devices, production devices are still to come into asneral use.

Jan 1, 1994

By S J. Loach

Geological reconciliation is an indispensable part of BHP Billiton’s Western Australian Iron Ore (WAIO) operations. Since 2009 our reconciliations have been calculated in a single, centralised sequel-server database. This system draws data from across our operations and calculates a hierarchical sequence of reconciliation factors that span the company from the smallest grade control (GC) block to the whole of WAIO. It then presents the results using sophisticated graphical reporting tools.The initial motive for developing WAIO’s reconciliation system was to meet corporate compliance and public reporting requirements. The ability to validate our resource and reserve models by comparing their estimates of tonnes and grade with production figures remains the system’s principal function; however, as the system has matured, we have significantly developed its ability to support the improvement of various technical activities within the business. For example, the system can now calculate and report reconciliation factors for different resource classifications, short-term planning models and geometallurgical estimates.More recently, great emphasis has fallen on the system’s ability to detect and warn of possible geological issues that may pose a risk to either production schedules or product quality. We envisage a future where automated analysis of our large historical data set will enable high-risk conditions within future mine plans to be detected and highlighted.In all of these ways geological reconciliation plays an important role in contributing to this company’s financial and operational resilience.CITATION:Loach, S J, 2017. The development and future of BHP Billiton’s Western Australian iron ore geological reconciliation system, in Proceedings Iron Ore 2017, pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By P. Bermingham

A new approach to load testing of high capacity piles is presented. The method is mobile, inexpensive, repeatable and non-destructive allowing for multiple pile testing at a single site. A reaction mass is placed over a pressure chamber situated atop the pile to be tested. The test method is significant in that it can produce linearly increasing forces of high magnitude (over 5.0 MN) with durations of up to 80 milliseconds. This represents pulse durations an order of magnitude longer than achieved using a drop hammer. The accelerations the pile undergoes are less than one g, (conventional dynamic methods = 50 to 100 g). These effects combine to produce pile behaviour no longer dominated by the action of stress wave, instead the pile is under high levels of stress through its length during the force input. This is representative of the situation when static loads are applied, thus the method may be considered quasi-static. Further advances introduced with this method are that pile deflection and transmitted force are measured directly by means of a laser beam and load cell. This allows accurate correlation of event load displacement histories without the error associated with zero shift (acceleration integration) or non-homogeneous materials (strain measurement). The load displacement histories emulate those obtained for static load testing.

Jan 1, 1989

By Bern Klein

Motivation for Improved Energy Efficiency in Mining ? Canada potentially adopting Greenhouse Gas Emissions and Intensity Legislation in 2013 ? BC -Climate Action Plan and Energy Conservation Agreement in 2008 ? BC Energy Plan 2007 -BC Hydro is mandated to save 50% of new load growth ? TSM Initiative -Energy Management, Energy Reporting, Setting Energy Targets, GHG Management BC MOU for Energy Conservation Agreement -MEMPR, MABC, BC Hydro

May 1, 2010

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermo-physical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at the University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous case is modeled with walls, each having a different set of thermo-physical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By Philip K. Hopke

A systematic study of the mechanism of interaction of 218Po(RaA) armed by the decay of 222Rn with airborne particulate matter has been made. The rate of attachment of RaA to particles in the diameter range of 0.1 µm to 10.0 µm has been measured as a function of particle size, concentration, and composition, radon concentration, time of interaction, relative humidity and temperature. It was found that under the conditions in these experiments the attachment rate was proportional to the square of the particle diameter and varied with temperature and relative humidity. The composition of the particles apparently has no effect on the attachment. The variation in attachment rate was related to a sticking probability coefficient of approximately 0.02 that varies systematically with temperature and humidity. In addition, the rate of deposition of RaA on the wall of the attachment kinetics system was measured and also found to change with temperature and relative humidity.

Jan 1, 1980

By M E. Pierce, T V. Garza-Cruz

Rock mass strength and brittleness generally have a significant impact on both cavability and fragmentation. Variability in these properties across a panel or block footprint is of particular interest because stronger units have the potential to significantly impact cave shape. This paper describes how FLAC3D™ was used to examine the impact of variability in rock mass properties on predicted cave performance to aid in assessing potential risks associated with the proposed design.A case study orebody was subdivided into a number of domains to reflect the heterogeneity of the rock mass at the scale of a proposed inclined cave. The results suggest that the presence of stronger units has the potential to impact cave shape significantly in the southern half of the cave footprint and could increase the potential for cave stalling at shallow depths. If this unit is stronger and less brittle than expected, an overhang is predicted to develop in the southern half of the inclined cave at depth. The effective hydraulic radius is significantly reduced due to the overhang in the south, and the cave could eventually stall at shallower depths in the north.CITATION:Garza-Cruz, T V and Pierce, M E, 2016. Impact of rock mass strength variability on caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 359–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E. M. Watkin

"Land directly disturbed by hard rock mining activities in Ontario and Quebec was surveyed in 1974 as part of a country-wide assessment, (Murray 1977). Some 15, 000 hectares, or 5 7 square miles, are listed as having been disturbed by overburden removal, waste rock and tailings deposition (Table 1) in the region. That area represents sixty-eight per cent of the total area which ha1; been disturbed by mining in central and Atlantic Canada. Assessment of disturbed areas was undertaken using LANDSAT-1 and LANDSAT-2 satellite imagery. Certain limitations of the technique were recognized but the data obtained were considered a relatively acceptable assessment of the extent of disturbed areas larger than ten hectares.Approximately ten per cent of the land disturbed by mining in the two provinces has been reclaimed to varying degrees. Indeed, this proportion is correct for the country as a whole. As pointed out by Ripley, Redmann and Maxwell (1978), some of the land was disturbed long before environmental concern 01· reclamation were ever considered. In numerous instances reclamation will remain impossible until presently active operations are closed. Nevertheless, these authors feel such figures make it clear that reclamation has not been a high priority in Canada in the past. Canada is a vast country, and there has been little pressure toward efficient use of all land space. Most mining operations occur in areas distant from the country's population centres. Under these circumstances, therefore, the pressure to reduce the environmental impact of mining is much less than in the more densely populated areas of Europe and the eastern United States, where such activity can occur in or adjacent to large metropolitan areas."

Jan 1, 1980