Search Documents

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By Nobel Insurance Service

[Executive Director’s note: ISEE is committed to continuing its efforts to ensure that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. In the July/August 2001 issue of the J o u rnal we printed excerpts from “Carbon Monoxide - The Silent Hazard,” an article from the Safety Update, published by Nobel Insurance Services. We also re minded readers of the text from the 17th edition of the ISEE Blasters Handbook in its section on trench blasting as follows: “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underg round and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or N Ox may travel through the strata and find their way into basements of nearby homes or businesses.” While incidents are rare, a number of cases in re c e n t years have resulted from outdoor blasting operations p roducing carbon monoxide gas that has migrated t h rough the earth and accumulated in nearby enclosed spaces. T h e re are steps that a blaster can take to be proactive in preventing incidents. These steps and studies of the occurrence have been expertly presented in several papers presented at ISEE conferences and included in the ISEE Conference Proceedings, available th rough the Blasters Library. In addition, Material Safety Data Sheets provided with explosives used in surf a c e blasting should provide additional information on gases p roduced by detonation. Below, we have reprinted the IME white paper, entitled “Fumes from Blasting Operations.” The paper underscores the unique set of circumstances that combine to contribute to high concentrations of CO measurements in underground, enclosed spaces following the detonation of explosive materials and provides recommendations to blasters

Jan 1, 2004

By Hiroshi Yamazaki

The paper describes prediction, control and validation of face pressures, and special TBM features for the bored tunnels of the New Metro Rail City Project, Perth, Australia. The selected EPB-TBM passed below a heritage bridge and the operational Perth Railway station in ground conditions consisting of fully saturated uniform sand combined with shallow overburden and a horizontal alignment radius of only 135m. Therefore, strict control of volume loss, TBM operations and ground movements was vital requiring continuous evaluation and adjustments to TBM operation parameters. The paper discusses the effectiveness of applied TBM face pressures and the used foam/polymer soil conditioning which was measured against achieved volume loss and the predicted range of ground settlements.

By D. N. Bigby

This paper concentrates on ground control innovation in Europe since the first Morgantown conference, mainly from a UK perspective. In particular, it describes the rock engineering and ground control tools developed to address the mine support and design problems associated with coal mining at great depth in areas influenced by previous workings. The differences in approach across the Western European industries are also examined. Perhaps the most significant change in the period has been in the science of coal mine rock mechanics itself, with support design now based firmly on measurement, analysis and understanding. The ground control innovations described here have played their part in increasing the efficiency with which coal is mined and in increasing safety to the extent that fall of ground accidents are now rare.

Jan 1, 2006

By M. A. Schellhardt

In recent years development of instruments and equipment for determining subsurface pressures and temperatures in. gas and oil wells has made it feasible to obtain information that eras not available in the past on many gas-production problems. The material presented in this report illustrates particularly the value of subsurface-temperature data in the study of subsurface leakage from gas wells. An abnormal decline in the shut-in pressure of the Lone Star Gasoline Co. A. Jones No. 1 gas well in the southern part of the Buffalo (Tex.) field was observed during an interval when a negligible volume of gas bras being withdrawn from the reservoir. Wellhead-pressure readings indicated that the shut-in pressure of the well declined from 2,295 pounds per square inch gage on February 3, 1937, to 1,445 on February 12, 1935. Tests conducted by engineers of the Lone Star Gas Co. suggested that the subnormal pressure gaged on February 12, 1938, probably was not caused by a head of liquid in the well.

Jan 1, 1940

The U.S. Code of Federal Regulations (Title 30) requires that a methane monitor be placed on every mining machine to continuously observe and record methane levels at the face. The monitor must provide a warning whenever methane levels are 1.0 percent or higher. An effective monitoring system will indicate a methane concentration of 1.0 percent on the mining machine before methane levels at the mining face reach 5.0 percent. Where the methane monitor is located on the mining machine is one of the most important factors that determines how effectively face methane levels can be predicted. Any change in the sampling location will result in a change in measured methane concentration. To protect the methanometer, it is usually located on the cutting boom at least 1 to 1.8 m (3 to 6 ft) outby the front cutting bits. A face ventilation system using blowing tubing was simulated in a full-scale test facility. Methane released from the face area was monitored at multiple locations on a model mining machine as well as locations near the face. Based on the relationship between concentrations measured on the machine and at the face, criteria were developed for selecting the best machine locations for monitoring methane. Recommendations are given for revising methane action levels for alternative sampling locations.

By B. Tiryaki

Longwall shearers usually suffer from excessive pick and pickholder consumptions and severe wear of the back plate of the clearance ring section of shearer drums. In practice, most of the drums were seen to be withdrawn from the face due to the abovementioned problems, while vane picks and their holders were intact due to the improper lacing design of the clearance ring picks. However, few underground investigations and their results on the effect of lacing arrangement of clearance picks on the service life of shearer drums have been published. Nevertheless, the pick consumption characteristics of shearer drums were not investigated in detail, since these are fewer pick consumptions with shearers when compared to roadheaders. This paper is concerned with the comprehensive in situ trials on the effect of lacing of clearance ring picks on the lifespan of shearer drums, and the pick consumption characteristics of longwall shearers at Cayirhan Coal Mine in Turkey. The lifespan of shearer drums employed with shearers in this mine increased 70 per cent, while the consumption rate of clearance ring picks decreased threefold through using an alternative lacing for clearance picks, indicating the significance of utilizing proper design techniques for clearance ring picks for the service life of shearer drums. Statistical analyses carried out, using the raw pick consumption data, implied that the clearance ring picks experienced much higher loads than vane picks, revealing that special attention must be paid to designing clearance ring picks. An average maximum consumption value of 41 was determined for clearance ring picks, with corner-cutting picks having the most replacements, while it was 35 for vane picks, on three-day based pick replacements.

Jan 1, 2004

By Pierre Boileau

Outline ? Who are We? ? Canada?s GHG Emissions 1990 - 2000 ? Emissions from the Petroleum Sector ? Emissions from Petroleum Exports ? Emissions from Manufacturing Industries ? Emissions from Mining and Metallurgy ? Conclusions Greenhouse Gas Division Key Functions: ? National GHG Inventory Report, Emission & Removal Trends Analysis, and Indicator Fact Sheets ? Scientific and Engineering Guidance, Technical Advice, Data Quality Assurance & Quality Control and Methodological/Data Development ? International Negotiations (FCCC) & scientific/technical guidelines (IPCC & ISO) ? Expert Review Teams (ERTs) ? Outreach ? GHG Verification Centre ? Clearinghouse ? Protocol Development

Nov 1, 2002

By B Powell

Coastal acid sulfate soils (ASS) are wetland soils and unconsolidated sediments that contain iron sulfides which, when exposed to atmospheric oxygen in the presence of water, form sulfuric acid. ASS form in protected low energy environments such as barrier estuaries and coastal lakes and commonly occur in low lying coastal lands as Holocene marine muds and sands. When disturbed, the iron sulfides in these soils can oxidise and produce large volumes of sulfuric acid (essentially similar chemistry to acid rock drainage with mines) resulting in the subsequent release of toxic levels of iron, aluminium, manganese and possibly heavy metals. This results in detrimental effects on aquatic biota, plants, animals and steel/concrete structures and on human health in the surrounding environment. There are an estimated 2.3 million ha of ASS located along 6500 km of the Queensland coastline. In contrast to many mineral sulfides encountered in the mining industry, the pyrite crystals in ASS can be as small as 2 mm and commonly occur as framboids with extremely large surface area per unit mass, substantially increasing their reactivity if exposed to air (oxidation). Highly reactive iron monosulfides can also occur, particularly in drains and shallow lakes. Many coastal areas, where some 80 per cent of the population of Queensland reside, are coming under pressure for agricultural and urban development. Construction of canal estates, marinas, housing/industrial estates, roads, golf courses, aquaculture ponds, sand/gravel extraction and drainage for sugar cane can disturb ASS and release sulfuric acid, which may then drain into adjacent waterways with heavy rain. As development continues to encroach on coastal lowlands, the identification, quantification and management of ASS must be addressed as part of a commitment to the principles of Ecologically Sustainable Development (ESD). ASS can be successfully managed by adopting best practices and following guidelines, but government, community and industry must collaborate to raise awareness, avoid æhot spotsÆ and develop more cost-effective solutions. Scientists led the education and public awareness program showing infrastructure and environmental damages arising from ASS in Queensland. Using results from mapping and research, they convinced policy makers, industry and polititians to accept the need for legislation founded on good science. The resulting æState Planning Policy 2/02: Planning and Managing Development Involving Acid Sulfate SoilsÆ identifies the StateÆs interest in acid sulfate soils. The Queensland Government considers that development involving acid sulfate soils in low-lying coastal areas should be planned and managed to avoid potential adverse effects on the natural and built environment (including infrastructure) and human health. SPP 2/02 states where the policy applies and when a development application will trigger the policy. It can also be used to assist local governments in preparing their planning schemes under the æIntegrated Planning Act 1997Æ. The SPP 2/02 comes with a æState Planning Policy 2/02 GuidelineÆ to provide advice and technical information on interpreting and implementing the SPP 2/02. This guideline has legal status in assisting in the interpretation of SPP 2/02. Those seeking more detailed technical information can now also access the æSoil Management GuidelinesÆ and ASS æSampling GuidelineÆ, available from the Department of Natural Resources and Mines website. These are some of a series of chapters being developed for the æQueensland Acid Sulfate Soil Technical ManualÆ.

Jan 1, 2003

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By D. Randolph Berry

Volume II contains appendices which explain and document the recommendations of Volume I. The following topics are covered: Appendix A Discussion of Recommended Guidelines Appendix B Worldwide Use of Oxygen Self-Rescuers Appendix C Hypothetical Use of Oxygen Self-Rescuers in Post-1972 Coal Mine Explosions and Fires Appendix D Vibration Testing of SCSRs Appendix E Testing of In-Service Chemical Oxygen SCSRs Appendix F Discussions with Representatives of Underground Coal Mining Appendix G Recommendations for SCSR Storage Containers Appendix H Example SCSR Storage Plans Appendix I Testing of In-Service Compressed Oxygen SCSRs Appendix J 30 CFR 75.1714, 30 Regulations Pertaining to Self-Rescuers

Jan 1, 1981

By T. Tholana

South Africa hosts some of the world?s largest known resources and reserves of minerals that are strategically important to the global economy. The country?s mining industry contributes significantly to the national economy in terms of gross domestic product, export earnings, corporate tax receipts, remuneration earnings, and employment. Platinum, gold, and coal are significant minerals because they make the largest individual contributions to these economic indicators. Several factors impact the cash cost performance of operations that mine these minerals, thus affecting the future sustainability of these operations, which are generally ?price-takers?. It is therefore important that the cash cost performance of operations for these key minerals is analysed. Commercially available industry cost curves can be used for such analysis. However, some companies may not be able to afford to purchase these curves. This paper presents a simple Microsoft Excel® algorithm for constructing the curves. It also demonstrates how the constructed industry curves were used to analyse the cash cost performance of South African mining operations for the three selected minerals for the period 2007 to 2011, which included the 2008 global financial crisis. The analysis revealed that the operations were affected by several global and local factors during the review period. The work reported in this paper is part of an MSc research study at the University of the Witwatersrand. Keywords cost curve algorithm, economies of scale, cash cost performance

Jun 1, 2013

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By C D. Rawlings

An assessment is made of the potential for thick seam underground mining of black coal in Australia. A brief summary is given of the geo-mechanical environment and previous mining history existing in a number of areas of particular interest from the point of view of thick seam mining. A classification of thick seam mining methods is presented with emphasis on the critical geo-mechanical parameters influencing the performance of such methods. A summary is made of perceived geo-mechanical research requirements related to thick seam mining in Australian coalfields.

Jan 1, 1980

1. BOYD, JAMES. Statement on the Investigation of Natural Resources. Hearings before National Re-sources Economic Subcommittee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 125-131. 2. BUCH, J. W., HENDRICKS, T. A., AND TOENGES, A. L. Statement on the Investigation of Natural Resources. Hearings before National Resources Economic Sub-committee, Committee on Public Lands, U.S. Senate, 80th Cong., 1st sess., on Investigation of the Factors Affecting Minerals, Fuels, Forestry, and Reclamation Projects, May 15, 16, and 20, 1947, pp. 231-235. 3. CONGRESS, U.S. An Act to Provide for the Establishment and Operation of a Research Laboratory in the Pennsylvania Anthracite Region for Investigation of the Mining, Preparation, and Utilization of Anthracite, for the Development of New Uses and Markets, for Improvement of Health and Safety in Mining, and for a Comprehensive Study of the Region to Aid in the Solution of Its Economic Problems and to Make Its Natural and Human Resources of Maxi-mum Usefulness in the War Effort. Public, No. 812, 77th Cong., 2d sess. (S-357), ch. 764, approved Dec. IS, 1942, 2 pp.

Jan 1, 1962

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By Jeffrey M. Listak

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner&apos;s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head&apos;s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By Martín E. Mendoza

En 2010 se identificó un peligro potencial en la pared Norte del Tajo Chaquicocha, donde existía fallas pre-existentes, catch bench reducidos (subestándar) y bloques colgados que presuponían condiciones de mala voladura de control. Por ello, se planteó la modificación del diseño Final del Tajo Chaquicocha, ya que la continuidad de estos malos resultados arriesgaba el minado de los Bancos inferiores. En ese sentido, el objetivo del presente texto estriba en lograr voladuras masivas, sin afectar la estabilidad de las paredes del Tajo Chaquicocha, así como tener beneficios económicos en la reducción de tiempo de minado por cada banco, y en la productividad (Dig Rate) de los equipos de carguío.

Sep 12, 2011