Search Documents

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By R. J. Leary

The technologies of contemporary iron and steel production and of direct reduction processes have been studied to identify and estimate the potential effects of direct reduction on mineral consumption and the problems raised thereby for the Nation's mineral supply to the iron and steel industry. Contemporary patterns of mineral raw material and energy consumption were determined from a study of the 1964-70 period. Major changes were observed in requirements for 14 of 20 principal commodities. Average practice in 1970 was compared to best practice to estimate the potential effects of implementing existing technology without recourse to direct reduction. Potential effects of direct reduction were estimated by comparing the mineral requirements for 95 percent reduced pellets with 1970 best practice technology for two cases of use: (I) complete substitution for hematite pellets in blast furnace burdens, and (11) partial substitution (40 percent) for scrap in electric furnace steel charges. Effects upon mineral supplies are described; important collateral factors are analyzed, and the principal metallurgical, industrial, and environmental consequences of implementing direct reduction are discussed. Major effects of direct reduction on the domestic steel industry and its mineral supply system are foreseeable. Direct reduction will (1) create a large demand for low-gangue iron ore; (2) relieve the dependence of the steel industry on coking coal, and (3) permit great increases in furnace productivity, both in blast furnace ironmaking and electric arc furnace steelmaking.

Jan 1, 1973

By M. Kalin

"SUMMARYWaste management in general, and the water treatment of mine and mill effluents, has become an ever increasing burden for mining operations. A reduction in these expenditures would undoubtedly be desirable if this could in fact be achieved within effluent guidelines and monitoring requirements.A brief summary is presented of the research which has as its aim the development of methods which would reduce such costs and lead to solutions for environmentally acceptable close-out conditions for acid generating mine waters. The basic concepts of Ecological Engineering and Biological Polishing are presented, together with an indication of the present state of these research efforts. Details are provided of the progress of various experiments which aim to promote reducing conditions, organic matter production and the establishment of biological filters which remove metals from the water which are then retained within the waste management areas. These conditions should lead to a curtailment of acid drainage and an improvement in effluent quality.A description is provided of the first pilot demonstration using this approach to achieve a walk-away condition for the close-out of a massive sulphide tailings resulting from 10 years of operating a copper/zinc concentrator in Northern Ontario.1.0 INTRODUCTION1.1 Waste management and close-outIt is recognized that the achievement of a cost-effective and competitive mining operation, from the commencement of exploration for ore bodies through to the day-to-day efficient operation of the mine, requires a certain expertise and sophistication. However, the environmental effects of these activities are considered peripheral issues and their importance as an integral part of the planning and development of the mine/mill, is not always appreciated."

Jan 1, 1988

Mine Terex articulated dump trucks are working on a large restoration project of an abandoned open cast coal site in Blacklaw, central Scotland. The project is part of the construction of a 42-turbine wind farm complex. During the scheduled 18-month duration of the project, three 28-t(31-st) Generation 7 TA30 dump trucks and the six 36.5-t (40-st) TA40articulated trucks are estimated to move about 1Mm3 (1.3 million cu yd)of material. The trucks are working12-hour shifts, 5.5days a week.

Jan 1, 2005

Keywords: Pyrometallurgy, Wits University, research Wits Metallurgy celebrated its centenary in 2004. The department has been at the forefront of education and research and has contributed greatly to the metals and minerals industry, both in South Africa and abroad, in terms of human resources and knowledge generation. A significant number of industry and academic leaders worldwide are Wits Metallurgy graduates. Since its early beginnings, pyrometallurgy has always been part of the curricula and research offered by the department. Pyrometallurgical activities started to expand tremendously from the middle of the 1960s, especially by the formation - together with Mintek - of the Pyrometallurgy Research Group, which continues its internationally recognised research activities today. The research efforts have been concentrated on problems associated particularly with ferroalloy, steel, stainless steel production, and PGM/Cu-Ni sulphide smelting. In recent years, research has been further expanded to physical modelling of pyrometallurgical reactors. Almost all of the specific research projects were handled from a fundamental point of view, and hence a large number of MSc(Eng) and PhD degrees were achieved by candidates under the supervision of the Pyrometallurgy Research Leaders. Moreover, a significant portion of the research results were published in internationally recognized journals and conference proceedings. Among these, Infacon and the Molten Slags, Fluxes and Salts Conference series are worth mentioning. The studies from a fundamental point of view include thermodynamics, phase equilibria, transport phenomena, kinetics, and process dynamic aspects of high temperature processes and systems, both in the solid and liquid states.

Jan 1, 2006

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By Christopher Cloete Uys, Luis Manuel Poinha Valentim

The purpose of this workshop is to describe and demonstrate the use of SPEEDWAVE, a high speed data recorder, its VOD enhancements, and the software which binds the system together. The system was designed by TLC Sohware, SOUTH AFRICA. TLC is a company spedalising in the solution of engineering problems, using computertechnology as a base. TLC was founded in 1987, and has since been involved in many different.measurement, control, simulation and modelling projects. Wth respect to the blasting industry, TLC has, in conjunction with AECI South Africa/ICI, developed a tunnel mining design aid, a ring blasting design aid, a multkhannel seismograph and a laser surveying program. In 1989, TLC designed and built the BA800. a microcomputer-based high speed recorder. These recorders are still in use and are producing valuable results. Based on improved technology and with the field experience of the BA800, TLC has designed and developed the data recorder SPEEDWWE.

Jan 1, 1995

By J. F. Papp

In the United States, chromium has been consumed in three major markets: chemical, metallurgical, and refractory. The predominant end use for chromium in the United States is in the metallurgical market as an alloying element in the production of stainless steel. In addition to being a major stainless steel-producing country, the United States is a major world producer of chromium-containing chemicals and has used substantial amounts of chromite ore for refractory applications. Chromium use is not easily further subdivided within the chemical and refractory industries because there is insufficient publicly available information to do so; however, chromium use can be subdivided among metallurgical industry uses based on the American Iron and Steel Institute (AISI) reported shipments of stainless steel by market classification (agricultural, aircraft, automotive, etc.). It is the goal of this study to determine the distribution of U.S. chromium apparent consumption among major markets in the United States. The distribution is expressed in the form of dimensionless fractions that are computed based on documented chromium consumption by major market. The distribution of chromium among markets within the metallurgical market is computed in a similar manner. Distribution factors are first computed for the major markets, then for markets that are subdivisions of the metallurgical market. The distribution of chromium among major markets has changed substantially over the time period of analysis. The fraction of chromium consumed by the metallurgical market has increased while that of the chemical and refractory markets has declined. Within the metallurgical market, the service industry market accounts for the greatest fraction of chromium consumption followed by transportation. Electrical, machinery, and fabricated products markets account for a substantial share of the metallurgical chromium consumption.

Jan 1, 2004

By J. A. Botín

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require of more complex risk evaluation models, that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, production rates, among many other). In this context, Real Option Valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed, which successfully quantifies the risk associated to dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mining Project.

Feb 27, 2013

By J. E. Misiewicz, A Rozendaal

Paper presented at Geofluids '93, held in Torquay, UK, 4-7 May 1993. The tin field consists of a fragment of Lower Proterozoic volcanosedimentary rocks surrounded by granitoids. Almost all the significant deposits are hosted by arkoses and are classified as replacement and space-filling types, with particular styles of mineralisation dominating at different mines. Petrological and geochemical investigation of borehole cores from four centres indicated the presence of a stratified zone 500-600 m thick and continuous over at least 20 km along strike, consisting of pervasively altered clastic arenitic sediments. The alteration is zoned into a grey-green sodic albitised footwall, an 80 m thick sericitised-tourmalinised sulphidic tin zone and a red haematitic potassic hanging-wall. The zoning and the localisation of three cassiterite phases are consistent with the tectonic history and with multiple pulses of stanniferous hydrothermal fluids derived from late differentiates of the granites over a prolonged period. Areas of high fracture density acted as conduits for the fluids, whose initially rapid ascent was retarded by decreasing pressure contrast, limited development of fracturing and/or impermeable shaly arkose to cause lateral spreading and pervasive alteration over a broad, stratified front. Lateral overlapping of local fronts at the various centres suggests a continuous zone, while the many petrological and geochemical similarities point to a shared fluid composition

Aug 1, 1995

By Ed Coulter

Nevada has a population of 1.2 million people of which only 21% or 312,rIXl are native born Nevadans. he population between 1980-1990 grew a record of 389%. and ls the fastest growing state in the union. While only 2.5% of the total population are direct employees of the mining industry, excluding Reno and Las Vegas, one out of every three people living in Nevada work for a mining related industry.

Jan 1, 1991

By C. Nexhip, S. Sun

Critical to understanding and controlling phase mixing and separation in metallurgical processes, is the development of reliable experimental techniques to measure interfacial properties of melt systems. A series of experiments has been carried out to determine the effect of oxygen potential on the surface tension of liquid copper. Using an electromagnetic levitation method, a surface tension-oxygen chemical potential adsorption isotherm was produced for the Cu-O system at T 1400 K. The surface tension results show good agreement with the literature values e.g. within 3 per cent for pure copper. The Belton `ideal' adsorption isotherm was applied, and the following equation derived to best fit the experimental data ? =1251-77.5 1n41+ (2.79x105 . pO1/2)](mN.m Using this equation, the surface tension of copper was calculated/predicted as a function of oxygen potential at 1400 K, and showed excellent agreement with the experimental values. This confirmed that the adsorption behaviour of oxygen in liquid copper is ideal. The saturation coverage of oxygen on the surface of liquid copper was determined to be T0 = 6.65 µmoles.m,-2 corresponding to an area per adsorbed oxygen atom of ao ? 25 Å2. These values agree well with those cited in the literature, and our experimental data cover a very wide range of oxygen potential (10-5 to 10-17 atm). Keywords: levitation melting, surface tension, Cu-O alloys, oxygen potential, adsorption isotherm, surface coverage.

Jan 1, 2004

By S. G. Shabestari, S. Saeidinia, P. Mokarian

"The experiments were conducted to investigate the influence of various process parameters in rotary degassing of aluminum alloy AS5U3G. Degassing was carried out by use of argon inert gas. The flow rate of the gas was investigated in the range of 12 to 21 L/min., 350 to 500 rpm rotor speed, 6 to 12 minutes degassing time, and 755°C to 780°C melt temperature. Degassing efficiency was evaluated through measuring the density of RPT samples. By optimizing the process parameters, RPT sample density was increased up to 2.73 g/cm3, which guaranties the production of high-quality aluminum castings. Tensile strength and elongation were increased considerably by degassing process. Scanning electron microscopy (SEM) shows small size and well-distributed microporosity. IntroductionOne of the major problems associated with the casting of aluminum alloys is the formation of gas porosity. Aluminum and its alloys are very susceptible to hydrogen absorption. Because solubility is much lower in solid state than liquid state, hydrogen atoms leave their position during solidification and combine together to form hydrogen molecules. These micrometer- scale cavities, called microporosity, cause the reduction of mechanical properties, particularly strength, ductility, fracture toughness, fatigue resistance, pressure tightness, and corrosion resistance (Laslaz, 1991; Jorstad and Rasmussen, 1993; Sigworth and Wang, 1994; Korasani, 1996; Anson and Gruzleski, 1999; Zhang et al., 2000). To avoid these problems and produce good quality castings, it is necessary to remove hydrogen from the melt. Several methods are available for degassing aluminum melt. One of them is a rotary degassing system using inert gas, e.g. Ar or N2. Various thermodynamic and kinetic factors govern the removal of hydrogen from molten aluminum (Anderson, 1987; Sigworth, 1987; Pignault, 1993; King and Reynolds, 1995). These are some parameters that affect degassing efficiency. Some of them are discussed here and some are examined in this project."

Jan 1, 2004

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By Christophe Thiébaut

Keywords: Pyrochemistry, Salts Treatment, Distillation The pyrochemical purification of metal generates spent salts. When this metal is an actinide such as plutonium, the slags cannot be discarded and are thus disposed in nuclear facility. In order to handle with these slags, the decision has been taken to reduce stored quantities. The development of a pyrochemical treatment is in progress in the CEA Valduc centre. The feed salt, typically composed of various Pu and Am species contained into monovalent or divalent chloride matrix, is first oxidized to convert the actinides into oxides. Then the chlorides are separated from the actinide oxides by vacuum distillation. Temperatures higher than 750°C for monochloride salts mixture NaCl/KCl and higher than 1100°C for divalent CaCl2 base salts, are required to produce an industrial flow of vaporization. Inactive qualification of the process for NaCl/KCl base salt has been carried out with lanthanide surrogates. Then, a pilot equipment, called distillator has been designed and built for production-scale distillation of NaCl/KCl and CaCl2 oxidized plutonium salts. Industrial flows of vaporization have been obtained with this pilot equipment : about 4 g/cm²/h for NaCl/KCl at 800?900°C and 1 Pa, and more than 1,5 g/cm²/h for CaCl2 base salts between 1000?1200°C at 0.1 Pa. The last step, now in progress, is the integration of the distillator into a glove box.

Jan 1, 2005

By D. Küster, G. Franken, P. Schütte, J. Vasters

The CTC (Certified Trading Chains) mineral certification system has been piloted in Rwanda since late 2008. CTC project implementation is jointly driven by the Federal Institute for Geosciences and Natural Resources (BGR) and the Rwanda Geology and Mines Authority (OGMR), in cooperation with other national stakeholders. Five Rwandan mineral producers participate in the CTC project with their flagship mining concessions. Based on independent third-party audits, CTC certifies supply chain due diligence measures of these companies engaged in the artisanal mining sector through on-the-ground assessments of mining conditions, transparency, as well as mineral origin and traceability. The CTC system thus allows responsible mineral producers and their clients to verifiably demonstrate supply chain due diligence and good governance in conflict-affected and high-risk areas.

Jan 1, 2011

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.

By Michael K. Phang

The use of explosives to fragment rock generates ground vibrations which may have a detrimental effect on contiguous underground coal mine openings. Increased surface blasting by a burgeoning number of surface coal mines and quarries has caused considerable concern among underground mine operators. Ground vibration effects generated from surface mine blasting are also causing public concern. In response to this concern, the U.S. Bureau of Mines (Stagg and Engler, 1980) has measured and analyzed ground vibrations and their effects on underground and surface structures. Some of the complaints registered against the mining industry are claims of substantial material damage from vibrations generated by the blasting; others are nuisance complaints of minor damage or annoyance. In general, allegations of damage from surface blasting have been sufficiently numerous to constitute a major problem for mine operators engaged in blasting operations. They have recognized the need for more technological data to evaluate the vibration problems associated with blasting. Both the operators and the general public need adequate safeguards based upon factual data to protect their specific interests. The coal mine industry needs reliable information from which to change blasting operations to reduce the number and severity of major damage claims and eliminate the growing number of nuisance complaints. The problem is of major concern not only to coal mine operators and nearby property owners, but also to federal, state and local governments. At the same time, environmental control agencies responsible for blasting and explosives use require reasonable and appropriate guidelines to protect the miners' lives.

Jan 1, 1984

By Derek J. Cyr

Climate has an immense impact on the properties of Athabasca oil sands and the ease or difficulty with which it is excavated and extracted. During the winter months, exposed oil sands surfaces freeze. When hydraulic and electric shovels used in the various operations in the Fort McMurray area excavate the benches, large frozen lumps are created. These lumps are either destined for a lump dump where increased costs are incurred due to rehandle, or they are sent to the primary crushers where they can cause significant downtimes by jamming the crusher. The crusher down time can sometimes be in the order of hours of lost production. Studies on data from two consecutive winters at Syncrude Canada?s North Mine show a high correlation between climate and the generation of frozen oil sands lumps. Temperature, ground cover, traffic, bench exposure time, oil sands grade and moisture content all contribute to this problem. A 1D frost penetration model was used to predict the depth of frost expected in oil sands and the corresponding likelihood of frozen oil sands lumps. To combat the challenge of frozen lump generation, a number of proactive and reactive measures can be taken: artificial snow, shallow ponds, scheduling, blasting or ripping.

May 1, 2004