Search Documents

In this paper, a mixed integer linear programming (MILP) model for the short-term scheduling of open pit mines is formulated. The proposed model aims at sequencing the blocks extraction over multiple short-term periods. The model takes into account multiple processes, waste dumps, and multiple stockpiles. The short-term scheduler makes a decision on the period, destination, and route that ore and waste are supposed to take to minimize costs while meeting all the mining and processing constraints. The destinations of the extracted materials are also controlled by their rock types. A monthly short-term production scheduling case study of an iron ore deposit is carried out over a year to validate the model.

Jan 1, 2011

By Xiang-yang Zhou

Keywords: Low-Grade Dolomite, Low CaO Content, High Specific Surface Area, MgO. A low energy consumption preparation technology of magnesium oxide with low calcium oxide content and high specific surface area from low-grade dolomite has been investigated. The optimum technical conditions for the preparation of magnesium oxide are the followings: dolomite is partially calcined at 750-800° for 2 h; the optimum solid-liquid ratio range in calcined dolomite slurry is 20-30 g?l?1; carbonation temperature, carbon dioxide pressure and end point pH value of carbonation are less than 40°, 0.4-0.6 MPa and 7 respectively during carbonation process; decomposition temperature of Mg(HCO3)2 solution is near 100°; calcination temperature of the precursor (i.e. precipitated basic magnesium carbonate) is less than 850°. More than 90% of magnesium can be extracted by the technology. The MgO product (CaO < 0.38%) with a specific surface area of near 50 m2?g?1 also can be obtained by the technology.

Jan 1, 2005

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

By N Weerasekara, M Powell, P Toor

The effect of liner wear on SAG mill performance has gained much attention in recent years. It is commonly observed that the three key performance criteria of SAG milling; throughput, power and product size all improve as the liner wears.The increase in throughput is generally ascribed to the increase in the grate apertures and the increase in mill volume due to the wear of these components. Whilst the decrease in product size is attributed to the reduction in lifter height and angle, resulting in more breakage by means of attrition and abrasion.Though it is widely acknowledged that the wearing of liner components such as Lifters, Plates and Grates have a significant impact on mill performance, their individual contribution to changes in mill performance has been unclear, and resultantly lead to questions like; what percentage of the throughput increase can be attributed to the increase in mill volume (plate wear)? and how much can be attributed to the increase in grate aperture (grate wear)?It has been found that through the use of grinding surveys, analysis of production data and JKSimMet it was possible to separate the effects of changing liner profile, increasing mill diameter and increasing grate aperture on the mill performance allowing for the quantification of each.The outlined methodology allows for both troubleshooting of problem liner components which reduce milling efficiency in their wear life as well as providing a basis for a more quantitative approach to liner design and reline scheduling.CITATION:Toor, P, Powell, M, Hilden, M and Weerasekara, N, 2015. Understanding the effects of liner wear on semi-autogenous grinding mill performance, in Proceedings MetPlant 2015, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Kieran Black

The immediate roof lithology at United Colliery is extremely variable and provides a challenge for the design of secondary support. Support design in recent longwall installation roads at the mine has been carried out using strata management techniques. These techniques allow a robust yet economical secondary roof support design to be achieved. Analysis of roof lithology and roof displacement during first pass driveage are used as a basis for the optimisation of the secondary support design prior to roadway widening. This paper will demonstrate the application of practical strata management techniques in the optimisation of secondary roof support in six installation roadways at United Colliery. The experience gained from the installation roadways for LWs 1 to 5 will be briefy discussed. The experience from LW 6 will be discussed in greater detail. The paper will describe the strata management system that was used, including mapping, borescoping and extensometry, as well as the development and application of a Trigger Action Response Plan (TARP).

Jan 1, 2007

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R and TGA testing setups in our ventilation laboratory, samples from US coal mines have been collected and tested. 70 The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal which is a good indicator for potential of self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential of coal self-ignition. The trend of activation energies determined using TGA techniques and adiabatic tests are reasonably consistent with each other. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal are easier to be activated with a small amount of activation energy at a relatively low temperature, the coal will has a higher potential of self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with low potential of self-ignition has low self-heating rate, high activation energy and high minimum self-heating temperature.

Jan 1, 2012

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

By P. J. Bartlett

Premier Diamond Mine exploits a kimberlite orebody using cave mining methods. A drilling level is established at the base of a block of ore to effect undercutting that leads to caving of the overlying ore. A second level is developed some 15 metres below the undercutting level to allow extraction of the ore once it has caved. As much as 45 per cent of the rock is removed on the extraction level creating a series of pillars. Undercutting creates abutment stresses, as high as 3 times the virgin stress, which affect the rock mass to a distance of 20 metres from the undercut face on the undercut level and on the extraction level 15 metres below. If the extraction level is completely developed prior to undercutting, where stress levels exceed 20 percent of the rock mass strength, extensive rock mass and support damage occurs as the undercut passes overhead. Rock mass damage takes the form of movement along existing joints and minor shear failure through intact rock. Support damage takes the form of cracking in rigid concrete linings. Where induced stresses exceed 50 per cent of the rock mass strength it is often impractical to keep excavations on the extraction level open. Rock mass damage takes the form of extensive failure of the rock in shear which evidences itself as propagation of the fracture zone around tunnels and footwall heave. Support damage results in destruction of shotcrete linings and concrete footwalls. As the interbolt support fails, badly fractured rock ravels around the steel tendons. Observation and monitoring at Premier Mine and on other cave mines has shown that induced stress levels and consequent damage are a function of :?the extraction ratio on the undercut and extraction level prior to undercutting ?the shape of the undercut face ?the rate of undercut advance ?the distance of leads and lags between adjacent tunnels on the undercut level. To ensure the stability of excavations, all of the above parameters must be carefully planned and the planned mining sequence rigidly enforced. The minimum of development is completed on the extraction level prior to the undercut passing overhead. Required development is then rapidly completed once the area has been de-stressed. Support is installed in three phases: ?Rockbolts are installed as soon as excavations are developed ?Wire mesh, steel tendon straps and a layer of shotcrete sufficient to protect the mesh and straps from damage by blasting and LHD loading is installed as soon as practical thereafter. Inevitably the shotcrete lining has to be replaced once the undercut has passed overhead.. ?Rigid shotcrete linings and concreted footwalls are completed only after the undercut has passed overhead and the area has been de-stressed.

Jan 1, 2000

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By Joseph Daly

An investigation into inaccurate scatter of pyrotechnic detonators led to the innovation of utilising existing (every day) equipment in a manner to accurately determine the true scatter of detonators. This can then be utilised to determine the accuracy of a particular batch of detonators.

Jan 1, 2014

By David R. Skuse, Jacek A. Kostuch, Steven M. Fortier

"Particulate ground calcium carbonate (GCC) is used as a filler and coating pigment in a wide range of applications including papers, paints, plastics and films. In this paper we will overview the requirements for GCC used in both filling and coating applications in the paper industry and highlight the processes used in the production of these materials.INTRODUCTIONCalcium carbonate is both abundant and very widely distributed occurring most commonly as limestone, marble and chalk (Harben 2002). Given, the high purity, whiteness and relative inertness of these materials it is not surprising that they are heavily utilised in a range of industrial applications. Worldwide ground calcium carbonate (GCC) capacity is estimated at 50.5 million tonnes per year (Roskill, 2002). This usage is divided between relatively coarse materials that are used in applications such as landscaping, cultured marble and carpet backing and finer grades that find application in plastics, rubbers, inks, paints and paper. Given the usage of calcium carbonate products across a very wide range of consumer products, the outlook for GCC is very promising with growth expected in many markets. Growth is anticipated across many applications in the emerging nations and more specifically in paper applications on a global basis.Over the last several decades the GCC processing industry has evolved to be well adapted to both the cost effective production and delivery of standard products and the production of high performance speciality products. Many of the standard unit operations found in the metaliferous raw material processing industry are also used, albeit in some cases in modified form, in the processing of GCC. Coarse products (diameter > 3 - 10 µm) are typically produced by dry processing routes. Whereas, the finer products are typically produced by a combination of wet and dry processing."

Jan 1, 2004

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

This paper reviews rehabilitation, closure, and post-closure management of the Tui, Golden Cross, and Martha Mines, all of which are located in the Waikato Region of New Zealand. There was no requirement for rehabilitation of the Tui mine, which was abandoned in 1973. There was a requirement to rehabilitate the Golden Cross mine. Mining at that site ceased in 1997, and rehabilitation is now well advanced. When first approved, there were some requirements for rehabilitation of the Martha Mine, but when reconsented in 1998, those were extended, and in addition a requirement for post-closure management was included. As a result, a Trust, funded by the mining company, has been established to take long-term responsibility for the site following completion of closure. The different rehabilitation/closure requirements at each of these sites illustrates that we have learnt something from the experiences of the past.

Jan 1, 2003

By M. K. Elmouttie, G. V. Poropat

Mapping of exposed rock walls provides data on geological features such as joints, bedding planes, faults etc critical to the economics and the safety of mine operations. Traditional, manual methods of mapping can be time consuming, error prone and limited in their coverage. New methods have been developed to map exposed faces remotely and safely however the benefits of these methods are only fully realised when exposed structures can be quickly and easily mapped using automated methods. This paper describes the application of an automated method of analysis of 3D images that provides users with the capacity to map exposed structures automatically. The method is based on the use of vector classification methods used in some neural network systems and provides rapid and reliable identification of exposed planes. CSIRO Exploration and Mining is applying these methods to 3D images for a range of applications from pit mapping to machine automation.

Jan 1, 2006

By Valois R. Shea-Albin

Increasing pressure from State and Federal agencies to mitigate mining-induced subsidence damage to overlying structures has presented a unique problem to the coal industry in the western United States. Because sandstone escarpments are an environmental issue, millions of tons of coal reserves that underlie these escarpments risk being classified as unminable by regulatory agencies. At this time, the effect of subsidence on escarpments has not been well documented or characterized. The Bureau of Mines is using numerical modeling techniques to analyze escarpment response to longwall mining. Two- and three-dimensional finite element models have been constructed for a study area near Price, Utah, where longwall panels were mined near an escarpment. This status report includes preliminary results showing that the pattern of subsidence surrounding the escarpment can be simulated through numerical modeling. Models that include such structural details as joint and fracture patterns will better simulate subsidence patterns .and magnitude. By locating longwall panels strategically in relation to the escarpment, stability may be preserved throughout the mining process. Numerical modeling provides a method to analyze relatively quickly the effects of longwall panel location and resulting subsidence on escarpment stability. The goal is to provide a relatively accurate predictive tool for mine planning to determine if escarpment stability can be maintained while maximizing extraction of the coal reserves.

Jan 1, 1986

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By Raymundo Del Carpio

El presente trabajo señala las bases que fundamentan la aplicabilidad del extracto de quebracho como depresor en el proceso de flotación, donde se realiza una combinación de un dispersante (producto obtenido a partir de extractos vegetales). También se muestra los avances sobre procesamiento de minerales con alto contenido de pirrotita. En ese sentido, se busca desarrollar una tecnología eficiente y ambientalmente limpia, considerada como una herramienta para la mejora de la competitividad de la empresa, a partir de una visión de desarrollo sostenible.

Sep 9, 2007