Search Documents

By D. S. van Vuuren

Over the last 60 years many different processes were conceived to reduce the cost of titanium produced by the Kroll process. However, success eluded all previous efforts, which were consequently terminated in periods of economic downturn. Recently, the grow thin demand for titanium and the high cost of producing the metal again sparked renewed attempts in various parts of the world to replace the antiquated Kroll process with a more efficient route. The different options to produce titanium are reviewed, classified and evaluated in terms of the fundamentals underlying the technologies, and it is shown that the options considered to be the most likely to replace the Kroll process, are continuous processes to reduce TiCl4 metallo-thermically to titanium powder. Of these, continuous magnesio-thermic reduction of TiCl4 would conceptually result in the lowest-cost and highest-value product. However, when considering by-product salt removal from the titanium product and recycling of the salt as well, sodio-thermic reduction of TiCl4 is better.

Jan 1, 2009

By Gruenewaldt von

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. The principles of shear-driven aggregation of particulate matter suspended in fluids, a common industrial method of concentration and separation, were applied to a convecting magma to estimate the time required to sparge or strip the PGE and Cr content and concentrate it into the boundary layers. It was calculated that an ore-grade (e.g. 6 ppm PGE) boundary layer about 1 m thick would require 100 000 years at most to form from a body of magma 500 m deep with a PGE content of 20 ppb. Since concentration would be most vigorous when the magma was warmest, at least half of this concentration would take place in the first 10 000 years. The effect of dispersive pressure in the boundary layer would generate a concentration high of refractories just below the top of each boundary layer and another just above the bottom. If the magma was a double-diffusive system, it might evolve by the downward cascade of enriched boundary-layer material into the hotter, lower magma layers, where depending on saturation levels chromites would equilibrate and sulphides undergo partial or total resorption, enriching PGE levels in any remaining sulphides. This cascade process would in time greatly enrich the lower regions in PGE-bearing sulphides and chromites

Apr 1, 1994

By K A. Campbell, K A. Rodgers

The Plumduff sinter occurs at Whenuaroa, near Puhipuhi, approximately 30 km north of Whangarei. It is one of three residual sinters in the southern portion of a mid- to late-Pliocene geothermal system. The deposit consists of many large sinter breccia boulders, including rudrocks (coarse breccias), scattered around the flanks and summit of the small conical hill of Plumduff. Three types of sinter breccia occur: (i) rudrocks consisting of large, angular to sub-angular clasts of layered sinter up to 0.8 m across, as well as smaller clasts of sinter (20 - 100 mm dia), and fragments of stromatolitic structures; all clasts are supported in a matrix of microcrystalline, transparent to translucent to milky quartz; (ii) fragments of layered angular to irregularly mottled sinter of white to grey or bluish hue supported in a translucent to opaque silica matrix; (iii) smaller, matrix-supported breccias with clasts both partially surrounded and/or penetrated, by a clay-like weathering rind, and sinter conglomerates with rounded to oblate clasts. Three principal types of fabrics constitute the bulk of the sinter: (i) stromatolites, including columnar, palisade and filamentous networks, showing progressive silicification, in fenestral, tufted to clotted fabrics; (ii) peloids and pisoids; (iii) plant-rich facies in which various silicified plant species occur in a silica matrix. All fabrics have counterparts in hot spring deposits in the Taupo Volcanic Zone formed at temperatures from 75¦C to 35¦C. Also present is steam-condensate-produced alteration: kaolinite and alunite as well as boulders of quartz lattice texture. Cinnabar only occurs in sinter on the north and south central slopes of the hillside. No quartz veins or geyserite were recognised.

Jan 1, 2001

By Terry M. Tilley, Gregory P. Sherry

Purpose This is a unique project because the mining and tunneling industries have become highly mechanized and cannot normally accommodate a project where surface disturbance must be minimized or eliminated when there is less than 10 feet of ground cover. More traditional less mechanized methods must be employed and the skills and techniques for accomplishing the work have become all but non-existent. Therefore, this article highlights those areas of specialized skills and techniques. Methods The article will describe the design approach, the method(s) of ground support selected, the method(s) of excavation selected, the planning, scheduling and materials selection process. In addition, the article will describe the actual production characteristics and the results of the project. This approach will concentrate on productivities, adaptations to actual conditions and the quality of the end product. The design approach basically was to insure that the temporary support methods were adequate for the excavation and shoring stage of the project. The final concrete liner was designed using conventional structural design methods with the goal of constructing a tunnel that will last 100 years. The methods of support were spiling and variations of spiling in order to provide advance temporary ground support. In this project spiling is steel channel cantilevered and driven into the ground ahead of the working tunnel face which supports the ground allowing the face muck to be removed with overhead protection’. Conclusion This will be a discussion of the applicability of the methods. The actual performance of the excavation and shoring methods will also be evaluated. The final concrete liner completion results, the actual production rates and the conformance with budget and schedule will be addressed.

Jan 1, 2005

Despite technological improvements and better understanding of the hazards, coal dust explosions stilI occur. Experimental explosions in galleries in various countries extend knowledge with the constant aim of providing safer working conditions. The inadvertent ignition of an accumulation of methane is the traditional initiator of the coal dust explosion.There are specific parameters of coal dust explosibility and explosion propagation, including the important volatile matter in the coal, fineness and dispersibility of the dust and its concentration. Accepting that initiation cannot be absolutely prevented, it is necessary to consider explosion suppression. While both limestone dust and water are the chosen explosion suppressants, in practice water has more limitations to its efficacy when related to the degree of explosion violence. These data give rise to the criteria for explosion suppression, differences in favoured mining geometries, and using the same principles, to differences in suppression treatments.

Jan 1, 1988

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005

By K. Meyer

"INTRODUCTIONThe David Bell Mine Concentrator started production in April 1985. A staff of twenty-seven people operate and maintain the concentrator. The crew is grouped into the following main areas.16 Operators6 Assaying/Metallurgy/Refining/Clerical4 Maintenance people2 SupervisionOperating highlights of the following unit processes will be discussed in detail:Screening and ThickeningPre-aeration and CyanidationCarbon-In-Pulp Gold AdsorptionCarbon Handling andGold RecoveryFor a complete description of the concentrator, refer to the papers by: (1) C.V. Sibbald, Teck-Corona's Hemlo Mill, October 1984, (2) R.A. Ford, The David Bell Mine at Hemlo, From Exploration to Production, November 1987. For operating details of the grinding circuit and effluent treatment plant refer to papers by: (3) T.G. Smith, SAG Mill Experience at The David Bell Mine, October 1988, ( 4) AN. Veltmeyer, The Effluent Treatment Plant of The David Bell Mine, January 1989.TRASH AND CARBON SCREENSTrash ScreenThe vibrating trash screen is inclined at 5 degrees and is clad with a 28 mesh stainless steel cloth which is changed monthly during the SAG mill liner replacement/inspection shut down. Other screen openings and configurations have been tried and the screen has been by-passed to change the cloth ""on the fly"". These attempts resulted in fibres (usually wood) to report to #1 Carbon-In-Pulp (CIP) tank, where the fibres are trapped in the CIP launder screens, and downstream carbon handling screens causing serious blinding problems. The trash screen in a Carbon-In-Pulp (CIP) or Carbon-In-Leach (CIL) gold mill removes fibres before they:are reground in the ball millsaturate with gold bearing leach solutionplug launder screens in CIP or CIL tanksplug carbon circuit pipe screenstherefore the trash screen is best placed ahead of the thickener."

Jan 1, 1989

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mine operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also Investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result in reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By I. Mc Dougall

Finite element models were generated of two submerged arc furnaces of different geometries. A 48MW circular furnace and a 68MW 6-in-line rectangular furnace were studied. The electrodes, raw material, slag and molten metal were included in the model. ANSYS/Multiphysics was used to predict the current density distribution in the electrodes, raw material, slag and molten metal as a result of the three phase AC current. The effect of the electrode immersion on the current path was studied. The ?proximity effect? caused a pronounced asymmetry in the electrode currents in the circular furnace, whilst the electrode currents in the rectangular furnace exhibited radial symmetry. The current distribution in the melt in both furnaces indicated that the bulk of the current flows between phases. The current density is greatest between electrodes. Results were compared to qualitatively similar published work, operating experience and results of furnace dig-outs.

Jan 1, 2007

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By M. K. Seguin

The study described in this paper is first centered on the determination of the physical properties (gravimetric, magnetic, electrical, and electromagnetic) o f metamorphosed iron ores of the Carol Lake-Labrador City District. Different geophysical surveys available in the Carol Lake-Wabush area were interpreted quantitatively and the dimensions, attitude, and tonnage of the ore bodies investigated were determined. A geophysical-statistical study was undertaken which permitted the determination of the grade of iron, magnetite, and, subsequently, specularite in the ore bodies. A discussion of the theory and logical progression of the study and the application of the results to actual geophysical data is presented. The conclusions, which are of real significance from the economic standpoint, may be predicted from the data obtained from geophysical surveys before any diamond drilling is undertaken. An integrated interpretation of this type is useful in planning future exploration work and selecting the most favorable geological structures. It also serves as a guide to minimize and determine tonnage drilling patterns. The general conclusion that a restricted range of residual gravity and magnetic anomalies are a key to exploration is valid. Indeed large depths to the top of deposits are absent since all the ore bodies are overturned synclinal structures with tops located close to the surface. Certain irregular geometries do occur but they are not common and the alignment of the iron ore bodies is sub parallel so that magnetic anomalies are evenly reduced in the earth's magnetic field vector.

Jan 1, 1975

By Jena Moshen

Underground Bulk Systems (UBS) technology has gained widespread application in tunneling and underground mining owing to its safety, reliability, increased Velocity of Detonation (VOD) and excellent results. However, its application in perimeter blasting is still limited and researchers are looking at ways of harnessing this technology for perimeter control. This simplifies the charging process by using one cost efficient product for charging both the perimeter and grid holes. This paper presents a case study on the application of underground bulk emulsion explosives for perimeter control blasting in underground room and pillar platinum mines. In order to achieve the required coupling ratios in the perimeter holes, the emulsion is loaded into specially formulated smaller diameter polyethylene (poly) pipes. The effectiveness of this method was evaluated using information obtained during routine blast audits and data supplied by the mines on half cast factors, over break and under break as well as analysis of data from Ground Penetrating Radar (GPR) Scans over a period of four years. This method of perimeter control, has given the platinum miners in Zimbabwe a competitive edge in cost effective perimeter charging and blasting by simplifying the previously costly deployment of traditional barrels and other decoupled cartridges. The method has been adopted by all the platinum mines in Zimbabwe as it has proven to be a cost effective alternative of controlling the perimeter walls, along with other key benefits that relate to safety, productivity and effectiveness.

Jan 1, 2018

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

"Chairman: Professor J. Elbrond Rapporteur: Miss V. E. MartingPapers.Aids to planning production in coal mines by F. H. Deist and M. P. RobertsCapacity calculations, investment allocation and long-range production scheduling in German coal mines by F. L. WilkeOre reserve evaluation and open pit planning by J. M. Marino and J. P. SlamaThis session was devoted to the economic aspects of planning and scheduling. After Dr F. H. Deist had introduced the paper Aids to planning production in coal mines, Dr T. V. Falkie summarized the following formal contribution prepared jointly with Dr R. V. Ramani, describing the work that has been done at the Pennsylvania State University in the development of simulation programs for mine planning over the past 15 years:During the late 50's and early 60's, Monte Carlo simulators were developed to model continuous miner-shuttle car transport systems, track haulage systems, belt conveyor networks, etc. In the mid-60's attention was directed towards deterministic simulation of equipment performance, given the equipment characteristics and the system profile. In the late (10's all these systems (miners, shuttle cars, belts and trains) were integrated together to form a complete coal mine simulator and the program could predict the output potential of the system, given the mining dimensions, method and equipment employed. The actual sequence of coal-cutting operations is entered into the computer through the use of a special programming language which permits any type of mining configuration to be simulated. The simulator is hybrid in nature in that the shuttle cars, trains and belts are simulated deterministically, whereas rate functions with delay frequencies are entered for the continuous mining operations of sumping, shearing, fleeting, cleaning, etc. With suitable manipulation of the data, the program may be applied to all belt or conventional mining sections. Most of these simulators were developed through the assistance of grants from the Department of Mines and Mineral Industries of the Commonwealth of Pennsylvania and are available from the Coal Research Board of the Commonwealth,"

Jan 1, 2014

By William R. Yernberg

SME’s Arizona Conference was held at the Doubletree Hotel at Reid Park in Tucson on Dec. 4 and 5, 2005. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. Important topics discussed among the attendees included the price of copper, community relations and education.

Jan 1, 2006

By C. Pattenden

The viability, self-reliance and resilience of small communities are perennial challenges in regional Australia. Recent developments in Australian mining regions seek to govern the minerals industry in a more holistic way that contributes to sustainable futures for affected communities in different contexts. In some areas of the State of Queensland land use conflicts and the cumulative impacts of multiple projects and activities across time and space have come to the fore. In more isolated regions of Western Australia the dominant issues relate to overstretching people, infrastructure and services in predominantly mining towns. In both cases, there is an ambition for regional towns with a strong extractive industry presence to transition into desirable, liveable and affordable cities with a diversified economy. The paper analyses two strategies - the Pilbara Plan in Western Australia, and the Sustainable Resource Communities Policy in Queensland - to identify how these governance instruments are contributing to sustainable development.

Jan 1, 2011

The Effect of High Power Nanosecond Electromagnetic Pulses on Selectivity of Pyrite from Arsenopyrite

Sep 13, 2010

By D Nobes, D Trumm, D Manhire, A OÆSullivan, M W. Milke

Coal seam gas (CSG) exploration and development requires the abstraction of significant amounts of water. This is so because gas desorbtion in coal seams takes place only after aquifer pressure has been reduced by prolonged pumping of aquifer water. CSG waters have a specific geochemical signature which is a product of their formation process. These waters have high bicarbonate, high sodium, low calcium, low magnesium, and very low sulphate concentrations. Additionally, chloride concentrations may be high depending on the coal depositional environment. This particular signature is not only useful for exploration purposes, but it also highlights potential environmental issues that can arise as a consequence of CSG water disposal. Since 2002 L&M Coal Seam Gas Ltd and CRL Energy Ltd, have been involved in exploration and development of CSG in New Zealand. Anticipating disposal of CSG waters as a key issue in CSG development, they have been assessing CSG water quality along with exploration work. Coal seam gas water samples from an exploration well in Maramarua closely follow the geochemical signature associated with CSG waters. This has helped to identify CSG potential, while at the same time assessing the chemical characteristics and water generation processes in the aquifer. Neutral pH and high alkalinity suggest that these waters could be easily managed once the sodium and chloride concentrations are reduced to acceptable levels.

Jan 1, 2005