Search Documents

By J M. F Clout, E Donskoi

The ability to design a beneficiation process for a new orebody based on particular feed characteristics is a powerful and practical tool. A new technique has been developed where beneficiation outcomes can be calculated by combining feed size-by-size chemical analysis, mineralogy, liberation and particle characteristics with a series of simple theoretical unit separation models rather than a simple mass balance approach or an exhaustive beneficiation test program. The new technique provides the ability to rapidly identify ore types that have the potential to meet product specifications whilst also rejecting others that will not meet specification even if a perfect separation was achieved. Beyond the broad scale decision making process, practical mineral separation curves from actual plant data can be used to more closely simulate the proposed process. This approach reduces the amount of laboratory and pilot plant work necessary by targeting what process stages will be required, increases early rejection of uneconomic options, identifies problematic ore types or unit operations and is a step towards estimation of final grade and recoveries achievable in potential circuit configurations.

Jan 1, 2004

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008

Abrasivity and wear resistance are not intrinsic properties of materials, but rather parameters describing the interaction between the wear part and the material exerting the wearing action. Moreover, wear or, at least, that part of the wear which is due to the cumulative effect of minute scratches, is linked to the hardness disparity concept. Abrasivity, in this context, is a relative concept, pertaining to a metal-rock pair, rather than to a rock. Based on this assumption, a methodology has been developed and checked against actual cases, enabling description of the abrasiveness of a rock or the abrasion resistance of a metal through the ratio of comparable quantitative indicators. The paper describes the methods and provides examples of applications to practical cases (namely: rock cutting, excavation by means of tunnel boring machines (TBMs), rock crushing, and hydro-mill cutting).

Jan 1, 2012

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

Removal of Dilute Toxic Anions in Wastewater Using Aluminum Hydroxides Co-Precipitation Method

Sep 13, 2010

By Anastasia M. Suchowerska

The design of effective ground support requires a sound understanding of the pre-mining state of stress in the stratum to be mined. Irregularities in the stress field encountered during multiseam mining are governed primarily by the previous mining in the surrounding strata. The aim of this study is to quantify the effects of rock mass transverse isotropy on the vertical stress redistribution in the rock strata beneath supercritical longwall panels. Wilson?s equations for determining the stress distribution induced in and beyond a single longwall panel after it has been mined have been adopted, and a plane strain finite element analysis of an elastic medium, together with the stress changes predicted by Wilson, was used to calculate the final pre-mining stresses in the underlying strata. Values of the independent shear modulus (G¢) of the rock strata, ranging from 0.1 to 1 times the isotropic shear modulus (Giso) in the plane of the strata, and a Poisson?s ratio (?) of 0.25 have been investigated. The key finding of this study is that the predicted magnitude of vertical stress in the transversely isotropic strata beneath a mined supercritical longwall panel is larger and changes more quickly with horizontal distance than is the case for an isotropic rock mass. This finding is of significance for the design of ground support measures in multi-seam mining operations.

Jan 1, 2012

By Ian Misich

Surface subsidence resulting from "total extraction" of coal in the Collie Basin first occured in 1987 when Western Collieries Ltd trialed the Wongawilli mining method. Because very little quantitative subsidence data existed for the weak, Permian sediments, a research program was set up prior to the extraction of the first panel. The objective of the study was to be able to predict subsidence characteristics and effects prior to mining future total extraction panels. Attempts at predicting subsidence began using existing subsidence models from other coal mining regions, however, as more site information became available, it became clear that it was necessary to develop a separate, site specific predictive model for the Collie Coal Basin. Analysis of extensive field monitoring data for both surface and subsurface subsidence has produced a series of empirical models which can predict the shape of surface subsidence troughs and corresponding tills, and strains for rectangular panels and describe the sequences of ground movement from the mine root through to the ground surface. The fact that both subsurface and surface subsidence characteristics have tied in well, gives greater confidence for predictions made from these models

Jan 1, 1992

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By Earl L. Fosse

"Preliminary examination of the Khayyam mine indicated that greater reserves of copper might be found by trenching, sampling, detailed geological and topographical mapping, and diamond drilling. The deposit seemed to be a potential source of sulfur, also, for use in the manufacture of paper pulp.Formal examination of the Khayyam mine by the Bureau of Mines was a follow-up of a preliminary examination made by W.S. Wright and the author on October 19-21, 1944. John Reed and W. S. Twanhofel, of the Geological Survey, visited the property during the summer of 1943 and suggested that the prospect be examined further.Preliminary examination of the Stumble-On claim was made July 1-3, 1945, concomitant with the formal examination of the Khayyam mine 11/2 miles to the west.In its program of exploration of mineral deposits, the Bureau of lanes has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy, It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts pre¬liminary examinations, performs the actual exploratory work, and prepares the final report, The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches arc under the supervision of Dr. R, S. Dean, assistant director.Special acknowledgment is due Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for his help in the preparation of this report and during the project work.The Khayyam property is situated at 550 18’ north latitude and 1320 24’ west longitude on Prince of Wales Island in Southeastern Alaska. (see fig. 1.) The mine adit is 2,350 feet above sea level, near the summit of a mountain ridge, and 2.8 miles in an airline southwest of the head of McKenzie Inlet, a southern branch of Skown Arm. Skowl arm is navigable by ocean-going vessels .to the mouth of McKenzie Inlet, where reefs and rocky islands limit the channel width to 50 yards. Beyond this point the inlet widens to nearly half a mile. Coast and Geodetic Survey chart 8142 indicates from 12 fathoms of water at this narrow neck to more than 30 fathoms throughout the remainder of McKenzie Inlet, The old ore bunker and dock at the head. of the inlet are beyond repair. A new ore bunker and dock would have to be built if a large-scale mining operation were established.The mine can be reached by trail along the western ridge that lies on the west bank of Omar Creek. The trail is approximately 4 miles in length. The grade is rather steep to an elevation of 1,500 feet, but the last 21 miles can be traveled over gentle slopes along the crest of the ridge.Ketchikan is 30 miles by air and 42 miles by water from the head of McKenzie Inlet. Feed, hardware, fuel oil, lumber, and explosives can be purchased at Ketchikan and delivered by boat to McKenzie Inlet. By using an airplane, all small equipment and camp supplies could be using an airplane, all small equipment and camp supplies could be dropped with cargo parachutes near the mine."

Sep 1, 1946

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption of this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 million tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and -is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably arc in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By John C. MacCartney

In the Pennsylvania anthracite region, the principal source of U.S. anthracite, refuse disposal problems are common since cities and towns are located over the anthracite measures. The Bureau of Mines surveyed refuse banks in the area, determining that 863 banks containing aver 910 million cubic yards of material occupy a total area of about 19 square miles. The vast bulk of the refuse is located within 2 miles of the traffic centers of incorporated c unities which have a total population of 625,000. Twenty-seven banks are burning, causing considerable distress in a number of communities.

Jan 1, 1969

By Parker A. J, Giles D. E

Solutions of copper(II) sulphate in acidified aqueous acetonitrile leach copper from copper-lead matte derived from the drossing of lead with sulphur to produce solutions of copper(I) sulphate. The reactivity of the matte constituents towards copper(II) sulphate is Cu2S> PbS > CuS > > Pb. According to the leach conditions, part or ,all of the copper may be leached 'leaving a residue of CuS/PbS, or S/CuS/PbS04, or S/PbS04, to be recycled to the lead smelter. Complete extraction of the copper requires leaching with oxygen which occurs under mild conditions in the presence of acetonitrile and sulphuric acid in water. Copper is selectively recovered as a pure product by electrochemical or thermal disproportionation of copper(I) sulphate solutions. A notional process is proposed.

Jan 1, 1979

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill, considering mainly the role and specifications of the fill used but including û brief description of fill preparation and placement. Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. Results of a fill research program conducted by the author in Mount Isa since early 1968 are presented, involving both Portland cemented hydraulic fill and alternative, cheaper, additives for cementing hydraulic fill.

Jan 1, 1971

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V,Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By E. D. Gardner

This is one of a series of paper's being published by the Bureau of Mines on placer mining; it is written as a supplement to Information Circular 6788, "Placer Mining in the Western United States, Part III", by E. D. Gardner and C. H. Johnson which was published in February 1935. Since Information Circular 6788 was written (1933), considerable advance has been made in the technique of mining placer gravels with power shovels and draglines. Although new washing plants continue to be built in accordance with untried designs the trend of new installations is toward proved equipment. A substantial number of plants are now being operated successfully (1937).

Jan 1, 1938

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999