Search Documents

By Reginald Dias

Mining equipment life may be extended through preventive maintenance and the proper application of quality lubricants. There are several practices mine operators should consider implementing to preserve their equipment. An exercise in review — Begin by reviewing original equipment manufacturer (OEM) recommendations regarding servicing and maintenance intervals for each part of the equipment, especially the engine. And the verdict is — If the manufacturer’s recommendations have been followed, good. If not, owners/operators should begin periodic service work on equipment, to help minimize equipment downtime and extend engine life.

Jan 1, 2004

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By Axel Nitschke, Josef Arnold

Bochum’s Underground Lot 306 was characterised by a confined site and unique tunnelling methods. A highly mechanized construction concept was developed to achieve high progress rates. Bespoke backup systems for muck disposal and material supply were used. For the first time in suburban tunnelling, wet shotcrete, batched onsite, was applied. A three-storey underground car park had to be undermined with only1.5 m of overburden and had to be lifted several times by “compensation grout in.” An existing operational two-lane metro tunnel was enlarged without any major impact on train operation.

Jan 1, 2005

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011

By C. R. Edwards, J. R. Smith

"INTRODUCTIONThe purpose of this paper is to give an overview of the ALSANDS PROJECT, with emphasis on the approach taken in the design of the Primary Extraction and Froth Treatment Plants.The Alsands Consortium (Table 1) is a Joint Venture of 9 companies formed in 1978, with its prime objective to obtain governmental approval and concomitant suitable commercial terms to build and operate a third oil sands mining and upgrading facility in the Athabasca Oil Sands Deposit.Alsands Energy Limited is the Consortium Manager.The Alsands Project will provide about 10 percent of Canada's forecast crude oil production by 1990, which will be 20,700 cubic metres per day (130,000 barrels/day) of synthetic crude oil plus 1,100 cubic metres per day (7,000 barrels/day) of liquid petroleum gases. To construct Alsands the time required by construction labour, field non-manual and engineering support personnel as well as those trades involved in project-related urban development will total approximately 100,000,000 manhours or 50,000 man years. During regular operations, 4,800 people will be employed by Alsands.Approximately $13 billion will be spent to design, construct and start up the plant by the scheduled 1988 completion date."

Jan 1, 1982

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Felipe Calizaya

This study describes the principles involved in the design of a booster fan installation, the basic requirements, and the provisions needed to guarantee a safe operation of the unit. It also describes how a booster fan should be selected and what measures should be taken so that events such as uncontrolled recirculation of air in a mine can be avoided. A computer program called MFSELECT is presented to assist the ventilation engineer in the design process a For a given mine ventilation network, the program determines the duties of fans and regulators that will fulfill the airflow requirements of a mine and minimize the total power consumption. The application of the program is illustrated by the detailed solution of a sample problem. A Case Study based on the Jim Walter Resources' No. 7 Mine is utilized to describe the basic requirements for the design and operation of booster fans, and illustrate their potential benefits in mine ventilation. Finally, the study discusses a process control system designed to evaluate the safety conditions in the mine and report on the status of both surface fans and underground booster fans.

Jan 1, 1990

Six years ago it was my responsibility to give the presidential address, and now that privilege has come my way again. On that occasion we were gathered atWhyalla and I took the opportunity of putting before members some observations on the problems we then faced in Australia, and some gains we had been able to chalk up during those early postwar years. You may recall that we were then just beginning to emerge from the difficulties of postwar reconstructions - of fuel and power shortages, and a grossly inadequate manpower for the tasks facing us. The expansion of manufacturing industry in Australia greatly stimulated by wartime activities, and by the postwar developments of many institutions - ran ahead of the supporting services and of the supply of labour to do thejobs. For many industries this unfortunate state of affairs had meant operating at rates well below their installed capacities and therefore levels of output insufficient for Australia's rapidly growing needs. When I last spoke to you these problems were still with us, though their intensity was beginning to lessen as a result of vigorous efforts by industry and governments to reduce them. But I must confess that my thoughts on that occasion were full of those problems and of the effect they were having on the iron and steel industry of this country-of the coal shortage, the labour shortage, and the many other difficulties we were then faced with - and all at a time when the stepping up of our postwar expansion programme was of vital concern to all of us.What a different picture it is six years later! How greatly has the scene changed for the better. In 1951 Australia's postwar immigration programme was only in...

Jan 1, 1957

By C. S. Samis, D. P. Seraphim

In the presence of oxygen, galena is oxidized in an aqueous medium containing ammonium acetate in accordance with the following reaction: PbS + 1/2 0, + 2 NH~Ac -» PbAc, + So + 2 NH: + H2O. This reaction was studied in an autoclave under oxygen pressure by polarographic measurement of the concentration of lead ion in solution. Oxidation rate is parabolic. The reaction products are lead acetote and elemental sulfur, the latter forming a film on the galena crystal. Reaction kinetics appear to be determined by the diffusion of lead from the galena phase to the solution interface through the film of sulfur. RECENT applications of pressure leaching on a commercial scale have emphasized the metallurgical importance of the oxidation of sulfide minerals in aqueous media by oxygen under pressure. Research experience has shown that sulfates, thio-nates, and metal oxides are the products of humid oxidation of sulfide minerals in basic solutions. The metal oxides may be solubilized in the presence of a complexing ion.' Certain oxide minerals are also amenable to treatment by this type of oxidation.' Several kinetic studies have been made of reactions of this type. Stenhouse' found that pyrite (FeS?) oxidized in a sodium hydroxide solution to produce a soluble sulfate and an insoluble layer of iron oxide and that the kinetics of the reaction were controlled by oxygen diffusion through the oxide layer. Andersen' studied the oxidation of galena (PbS) in a sodium hydroxide solution under oxygen pressure. He found the lead and sulfur to be simultaneously oxidized to produce plum bite ions and sulfate ions, and that the reaction rate was proportional to the surface area of the galena. The kinetics appeared to be determined by the reaction of oxygen and water with the galena surface. In each of the above reactions the metal and sulfur components of the mineral were oxidized simultaneously and at equal rates. In the present study the alkaline medium has been replaced by an approximately neutral solution of ammonium acetate in which lead sulfate is soluble. Under the conditions no sulfate was produced and no sulfur could be detected in the solution. The metal component of the mineral was solubilized and the liberated sulfur remained as a film of elemental sulfur on the surface of the galena crystal. A kinetic study of this reaction was undertaken to establish the kinetic mechanism and to determine the rate controlling step. Specific reaction rates were determined by oxidizing crystals of galena of measured surface areas in an autoclave maintained at the desired temperature and oxygen pressure. The rate of reaction was followed by measuring the concentration of lead in the ammonium acetate solution with a cathode ray polarograph, employing stationary platinum electrodes incorporated in the autoclave. Experimental Materials and Equipment Crystals of galena obtained from Violamac Mines, Retallack, B. C., were selected for oxidation because

Jan 1, 1957

1. A statistical approach to some mine valuation and allied problems on the Witwatersrand. Unpublished Master?s Thesis, University of the Witwatersrand ? 1951. (Separate) 2. A statistical approach to some basic mine valuation problems on the Witwatersrand - J. of the Chem. Metall. and Min. Soc. of S.A., December, 1951 - discussions and replies March, May, July and August 1952. (Vol. 1?.1). Also: J. of the Institute of Mine Surveyors of S.A. December 1952, March 1953. (Vol. 1?2) 3. A statistical analysis of some of the borehole values of the Orange Free State goldfield - J. of the Chem. Metall. and Min. Soc. of S.A., September, 1952 - discussions and reply November 1952, and February 1953. (Vol. 1?3). 4. A study of the relationship between development values and recovery grades on the South African goldfields - J.S.A.I.M.M, January 1959, - discussion and reply April and October 1959. (Vol. 1?6) 5. On the departure of ore value distributions from the lognormal model in South African gold mines. J.S.A.I.M.M., November 1960, January and August 1961. (Vol. 1?8) 6. Developments in the valuation of gold mining properties from borehole results - Seventh Commonwealth Mining and Metallurgical Congress, 1961. (Vol. 1?9) 7. Effective pay limits for selective mining. J.S.A.I.M.M., January and August 1962. (Vol. 1?10)

Jan 1, 2014

Prediction of fragmentation by blasting is most commonly based on theassumption that a single distribution of pre-existing discontinuities is present within a blasted rock volume and that the underlying mechanism of failure is tensile failure. It is assumed that the tensile stress field created by a blast initiates and extends radial cracks around the blastholes. Interaction between radial cracks from different blastholes and the free surface creates rock fragments. In reality, fragmentation of the rock occurs due to two mechanisms.One is related to the compressive-shear failure of the rock (mainly rock matrix) close to the blastholes, while the second mechanism is the previously mentioned tensile failure of the rock mass. The secondmechanism of failure occurs in the form of extension of the larger cracks in the region beyond the crushed rock, and this type of fragmentation occurs after the crushing phase. In the case of hard rock or blasting where the extent of crushing is minimal, the currently used prediction methods give a reasonably good result. However, there are many blasting conditions where the amount of rock crushing is significant. In the case where fragmentation of the given rock volume occurs dueto two different mechanisms, modeling of the rock fragmentation with a single distribution function is not appropriate. To model the fragment size distribution generated by two different mechanisms, it is necessary to use a two-component fragment size distribution function and a scaling parameter that will determine the proportion of the fragmented volume created by each mechanism. The purpose of this paper is to present results of blast fragmentation modeling based on two mechanisms of failure. The two-component model (TCM) utilises experimentally determined parameters from small scale blasting and parameters of the Kuz-Ram model, for more accurate prediction of the complete rock fragment size distribution curve. The methodology is such that it is possible to predict complete fragment size distribution, including fines, of ROM product for a future mine, at the feasibility phase of mine design.

Jan 1, 1999

By José Arango

El presente texto describe la aplicación del sistema MIMS en las estadísticas de producción de la Sociedad Minera Cerro Verde S.A. El sistema fue instalado inicialmente para el control de mantenimiento de los equipos, movimiento logístico, y contable. Posteriormente, se realiza el cambio del sistema de información manual a un sistema computarizado, donde se analiza los problemas cotidianos del sistema de información antiguo y se los compara con los cambios experimentados. En ese sentido, el objetivo de este sistema es facilitar el alcance de sus metas a la organización mediante el uso eficiente de todos sus recursos disponibles: personas, información, equipos, tecnología, y materiales diversos. La eficiencia de la utilización del recurso de información es medida por la relación del costo para obtenerla y el valor del beneficio derivado de su uso.

May 25, 1998

By Bengt H. Fellenius

The bearing capacity equation?"the triple N formula"? is now about 50 years old. It was developed from theory of plastic resistance of metal to a cone being pressed into the surface of the metal, superpositioned by resistance due to shear in an interparticulate medium (soil; note, we are not dealing with metallurgy), and tempered by work necessary to move the footing into the medium. The equation (and its coefficients) was "confirmed" by tests on small footings placed at or near the surface of the soil. The equation is a basic tenet of every geotechnical textbook, manual, and code. Over the years, innumerable variations of the N-coefficients and adjustments to the equation have been published. The main assumption behind the bearing capacity equation is that a shear plane develops between two essentially otherwise unaffected bodies: the main soil body and a body comprised of the footing with some soil. Moreover, the notion is that a model footing placed at or near the surface of a soil would behave proportionally or similarly to a full-scale footing, or to even a same size footing (pile toe) placed at some depth in the ground. This is not in agreement with factual observations. It is suggested that the behavior of a small or large diameter footing as well as a pile toe is governed by compression of the soil below the footing or pile toe and not by "bearing capacity".

Jan 1, 1999

The acid plant consists of the following units: 1. Glover tower. 6. Mills-Packard type chambers. 3. Reaction towers. 6. Gay-Lussac towers.The sulphur dioxide bearing gases, used in the manufacture of the acid, are obtained from the roasting of zinc concentrate. Six Herreshoff type furnaces are available, each with an effective hearth area of 520 sq. ft.The concentrate contains approximately 30% sulphur, of which about 72 is ultimately recovered as acid. The oxides of nitrogen are added to the gases in the requisite proportions partly from nitrous vitriol and from nitric acid in the Glover tower, and partly from nitrous vitriol in some of the chambers and connecting flues.The acid leaving the Glover tower is cooled by the ordinary water-cooling coils, while the cooling of the chamber gases is effected by circulating water over the outer surface of the chambers, and by spraying nitrous vitriol and weak acid into them.Flow of gases throughout the plant is regulated and controlled by means of regulus metal fans, fitted with variable speed gears.

Jan 1, 1934

By Steve Cole

"The economic and strategic importance of PGE bearing deposits is fuelling renewed exploration and development efforts in the precious metals mining sector.This paper presents a review of the various techniques used in the processing of PGE bearing ores, from primary benificiation to processing routes for the different flowsheets that have been developed amongst current producers. Recent innovations such as preconcentration of ore using gravity separation, recent trends in flotation circuit design and the development of hydrometallurgical routes for the direct treatment of flotation concentrates without the need for smelting will be discussed. Data from recent projects will be presented to illustrate common characteristics of PGE ores and concentrates.INTRODUCTIONThe six platinum-group elements (PGE): ruthenium, rhodium, palladium, osmium, iridium and platinum, together with gold and silver, are considered to be ""precious"" metals. The recent spike in platinum and palladium prices coupled with the projected increase in demand for the metals has fuelled a spate of exploration and new projects in the PGE sector. Historically primary producers of PGE metals have controlled the flow of information relating to the mining and processing of these ores into the public domain. Very little published information relating to individual operations and processes is available in comparison to the abundant literature relating to other metals.The purpose of this paper is to provide a general overview of the issues relating to the processing of PGE ores. Each topic discussed could easily be the topic of a paper or book and so in many cases only the surface of the topic will be scratched. An attempt has therefore been made to provide as many references as possible.This paper discusses the classification and location of PGE ores, the mineralogical factors that affect recovery of PGE's, methods currently used for recovering PGE's and process trends in PGE metallurgy."

Jan 1, 2002

By D. J. Gilbert

As a preventive action, the geotechnical department at the mine analyzed the original topography overlying a conveyor tunnel at the mine. Several dewatering drains were installed to intercept water collecting from an old lakebed. Subsequently, 20 steel arches were installed to provide additional support in an area of tunnel where original geological mapping indicated Type IV rock. This project was completed ontime with no loss to production. Construction schedules had to be developed to half hour precision, to accommodate the installation.

Jan 1, 2011

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By R. Abela

In over ninety per cent of mineral sand plants, the most commonly used equipment is the spiral concentrator. The tonnage treated over typical spiral plants can range from as low as 200 ton per hour up to 6 000 tons per hour. Due to the limited capacity of each spiral, plants consist of multiple spirals assembled into banks. The mixture of minerals present in the sand feed requires several spiral stages to achieve the desired mineral recovery. Due to the complexity of the spiral circuits, there are always some design and operating problems that present themselves in plants. These range from slurry distribution, spirals operating at incorrect design parameters and feed variations. The material being treated is difficult to maintain in suspension due to its high density, resulting in segregation and preferential flow in pipelines, distributors and sumps. The objective of this paper is to highlight common problems associated with spiral installations to designers and operators of plants. Practical solutions are recommended in order to prevent and minimize these mistakes in the design. These solutions may be used to improve performance on operating plants.

Jan 1, 2003

By Carl Lubbe, Ron Frye

Numerous articles have been written regarding the effects of blast control plugs in an attempt to quantify stemming ejection rates, air overpressures, fragmentation’and other parameters measured using these devices. In an effort to further attempt to understand the function of these devices, field and laboratory research conducted with various stemming devices was performed to enhance existing data sets and analyze otherphenomena that occur when these products are used.

Jan 1, 1998