Search Documents

By Kush Patel, Gary Cavanough

Mining operations consume over 2.5 Billion Australian dollars’ worth of bulk explosives annually (Richardson, 2018). Despite the large volume of product used, current practices only conduct a cup density test of the product being used. Explosive products are made up of a number of components, each with an effect on the performance of the explosive. This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser. Through a total of 60 tests carried out on 10 different bulk explosive products the average error of each method was determined, the BEA presented an average error of 0.11%, whereas, the wet chemistry method presented an average error of 1.90%. This is a significant difference when considering the importance of formulation of explosives. Further investigation into the capabilities of the BEA are also presented in this paper.

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

Individual specimens of sphalerite from the Broken Hill lode vary considerably in manganese and iron contents, even within the same orebody, so that study of the overall variation of manganese and iron content of the sphalerite calls for the analysis of a large number of specimens. This difficulty has been overcome by analysing a series of recleaned zinc concentrate products, prepared from stope samples and their equivalents, from most of the developed sections of the lode. The analyses reveal that during the formation of the sphalerite the concentrations of iron, manganese and zinc in the mineralizing solutions varied independently of one another from place to place in the forming orebodies, and also in time.The overall pattern of variation of the iron and manganese contents of the sphalerite in the several orebodies of the lode bears a general resemblance to the overall pattern of distribution shown by several other elements, notably, cadmium, lead, bismuth and arsenic. The iron content of the sphalerite indicates that it was formed at a temperature of 6000 C. or higher, but the variation in its iron and manganese contents demonstrates that Kullerud's method for determining the temperature of formation of sphalerite from its iron content must be used with caution if only single specimens of sphalerite are available.INTRODUCTIONThe four chemical analyses available of specimens of practically pure sphalerite from the Broken Hill lode (Table 1) reveal that the manganese content of the sphalerite varies considerably, and that there is a significant variation in its iron content. The variations revealed between individual specimens within the same orebody in the same mine suggest that specimen material is unsatisfactory as a basis for studying the overall manganese and iron contents of Broken Hill sphalerite, unless a great number of specimensis analysed.

Jan 1, 1956

By Fred W. Brackebusch

"The use of paste technology for surface tailings disposal may offer economic, technical, safety, and environmental advantages for both underground and surface mining operations. Paste is a non-Newtonian fluid having some shear strength during transport and placement. The strength is augmented after placement by consolidation, water loss, and by addition of chemicals. Economical dewatering systems are necessary to the success of surface paste tailings disposal. In an underground mine, the paste backfill plant can produce paste for surface disposal about 50% of the time because only about 1/2 of the tailings are needed for backfill. The distribution of paste to the surface stack involves expensive pumping equipment and thus a nearby location of the stack is desirable. The viscosity of paste can often be manipulated by modifying pH. Placement of the paste in a designed stack configuration depends on topographic and climatic factors as well as paste properties.INTRODUCTIONThe use of paste technology for mine backfill is becoming accepted for underground mines mainly because of ground control and economic reasons. Paste technology is just starting to be applied for tailings disposal with only a few hardrock metal mines worldwide using the technology; however, it has been used extensively for red mud disposal in the aluminum industry. The disposal of dry tailings is very attractive from environmental and safety points of view because of limited water which might potentially escape and pollute river systems. Dry stacking systems, however, are expensive because of filtration and truck transportation costs. Paste can be produced from most tailings streams by special types of thickeners. Furthermore, it can be transported in pipelines, therefore paste technology may be more economic than dry stacking but still have some of the major advantages. Understanding of paste technology has improved through experience with operating underground backfill systems in recent years and because of testwork and research programs by mining companies, consultants and equipment vendors. Thus we may be on the verge of taking a new look at tailings management using paste technology."

Jan 1, 2002

By V. J. Southey

"This paper reviews the history of Wabana Mines from 1892 to 1966, inclusive, in order to clarify the essential factors involved in the achievement of maximum mining efficiency and in the search for an acceptable product to satisfy changing market requirements. It outlines the progressive steps taken to mechanize both surface and underground operations, and forecasts anticipated performance, assuming certain major plans could have been implemented. Results of extensive research in the treatment of the complex ore are discussed. Selected processing alternatives are compared as to feasibility in a summary incorporating estimated capital and operating costs."

Jan 1, 1969

By Gordon Revey

The challenge of managing blasting risk, types of risk, public perception, and a system for managing risk were covered in the first part of this article in the May/June 2000 issue of the Journal of Explosives Engineering. This final part of this two-part series provides a method for identifying specific blasting risks and reviews the importance of community relations.

Jan 1, 2001

By Paramguru R. K, Jena P. K

Increasing demand for copper, lead and zinc with continuous depletion of good grade ore reserves, warrants the need for utilization of lean and complex ores of these metals. There is worldwide effort to develop suitable processes for these purposes. The present paper deals with the chloride leaching of complex base metal sulphide concentrates of two Indian deposits. A two stage leaching process is suggested keeping selectivity of metal dissolution in view.In the first stage most of the lead and zinc are reacted with dilute FeCI3 (0.3M) solutions at a temperature ono°c where major portion of the lead remains in the residue and zinc reports in solution. After taking out lead chloride by brine leaching, the residue has been treated for copper dissolution. A concentrated FeCI3 leaching at boiling temperature as well as ambient aqueous chlorine leaching have been separately tried to dissolve out the copper from the residue. Based on the results obtained, a flowsheet for the proposed process is presented.

Jan 1, 1981

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By Conochie D. S, Grave N. C

Disposable-tip emf cells at present used in liquid steel can be used to measure the state of oxidation of high-iron slags produced in non-ferrous smelting. This provides a new tool for the control and evaluation of pyrometallurgical operations.An investigation of oxygen potential variations throughout a typical nickel smelter using the flash smelting technique gave a valuable insight into the process. Correlations of oxygen potential with ferric to ferrous oxide ratio and nickel content in slag were in reasonable accord with equilibrium data in the literature indicating that the probes may be used both as a plant investigation tool and possibly as a means of obtaining thermodynamic data for slags.

Jan 1, 1979

In 1950, about a third of the world?s population lived in cities. That figure has steadily risen throughout the following decades. Now it is believed that about 60 percent of the estimated 8.1 billion people in 2030 will be living in urban areas. The strain on infrastructure in cities in the developed world is already showing. And the rapid growth in developing nations today is adding to the shortage of materials, equipment and labor needed to keep up with this growth. So, while materials and labor may be in short supply, there is no shortage of work for the underground tunneling and space industry. In June, 718 of those professionals from around the world were in San Francisco, CA for the North American Tunneling (NAT) conference, put on by the Underground Construction Association (UCA) of SME. The attendees spent the three days of technical sessions listening to international authors discuss the state of the industry, new technologies that have become available and updates on major tunneling projects throughout the world. The accompanying exhibit attracted 79 vendors, who displayed the latest in tunneling and underground space equipment and services. In addition to the technical sessions and the exhibit, the NAT featured three short courses ? ?DRB Process Update Workshop,? ?Soft Ground Tunneling Technologies? and ?Underground Blasting Technology and Risk Management.? And the post-meeting field trip to the Devils Slide tunneling project near San Francisco was sold out.

Jan 1, 2008

The disasters between 1920 and 1979 in coal mines in Queensland and New South Wales due to underground fire, gas or coal dust explosion or to gas or coal outbursts, have been assessed. The evidence relating to disasters caused by gas explosion points strongly to divergence from safe mining practice as the main cause. There is a need for greater training and education of personnel, closer analysis of gas reports, better monitoring and testing procedures, improved ventilation standards and a policy where safe working practice is actively encouraged. Conditions in the New South Wales occurrences of gas explosion were similar to those at Collinsville, Queensland in that dykes, igneous sills, burnt out coal and faulting were common to all. Information on outbursts indicates that contributing factors were intrusions, depth of cover, fault zones and other geological disturbances, methods of work, pressure and type of gas.

Jan 1, 1982

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

The sulphide ores of the principal lodes of the Boulder Mines are mainly composed of a schistose guess with a varying proportion of silica and lime, containing tellurides of gold, silver and mercury, associated with iron pyrites. It is a great difficultyto obtain pure and homogeneous samples of the tellurides for analysis, and from a number of tests made with excellent specimens it was found hardly possible to procure two to agree in analysis, the precious metals being found to be combinedwith tellurium in most varying proportions indeed, a close inspection of a partially crushed specimen will reveal, even to the naked eye, the various shades of colour characteristic...

Jan 1, 1901

By Wawa Jaka Sungkawa, Slamet Rachman Jaka, Tom Dermody

Nowadays, with such a focus on environmental protection, surface mining activities have come under pressure to ensure their activities do not adversely affect the local surroundings. As part of the extractive process, blasting activities are an integral part of a mining company’s operational cycle. Consequently achieving beneficial blast results while complying with environmental requirements has become a key focus. This especially is the case when firing blasts within close proximity of residents where additional control measures need to be implemented to control vibration. One case where this occurs in Indonesia is in the Paringin Pit, one of the operational areas of the company's. The pit has complex geological conditions and is surrounded by several residential areas. Between 2014 to 2017 there were 12 cases of ground vibration exceedance due to blasting. As part of a continuous improvement project the company's targeted minimizing the vibration exceedance in this area. A project was undertaken to research and develop a method to confidently predict vibration. It was decided that the scaled distance formulas were not adequate to predict vibration when using non-electric detonators, as accurate wave propagation could not be achieved. The problem is how to manage of complex geology condition related with wave propagation in ground vibration control. Geological condition mapping with specific spatial range can and combine with Signature Hole Analysis be a solution to make wave propagation easier to accommodate in ground vibration control. With this new approach geological condition mapping with specific spatial range was produced that would minimize vibration while ensuring beneficial blast results. Introducing the new prediction produced nil cases of vibration exceedance in 2018 and beyond and proved that the Signature Hole Analysis in specific spatial range of geological condition is the preferred method to optimize blast result and maintain vibration control.

By G Chitombo, D Francis, P C. Stewart, I Brunton

The ability to precondition (weaken) a rock mass to enhance caving (cavability and fragmentation) is becoming increasingly important, as more potential caving deposits are in stronger rock masses, and at greater depth. This paper discusses a full-scale blast preconditioning experiment conducted at the Cadia East mining operation, including quantification of visible and microscale blast damage. From a cave mining perspective, the objectives of the experiment were to quantify the effect of confined blasting on rock mass characteristics relevant to enhanced caving, and to provide calibration data for the purpose of numerically modelling alternative blast preconditioning designs.The experiment was located approximately 360 m below surface, and consisted of two f165 mm blastholes (60 m vertical holes) and eight HQ diamond drill monitoring holes (35 m horizontal holes). The diamond drill holes were used to sample the rock mass before and after the blast at varying distances from the blastholes. Rock mass blast damage was quantified both visually using core logging, and on a microscale using LABYRINTH® statistical analysis of X-ray microtomography data. Results from the experiment indicated four major findings:on the visible scale, the experiment indicated a 147 per cent increase in the number of hairline cracks within 5 m (p value = 0.015), but no change in geotechnical logging parametersmicroscale tomography of intact rock samples indicate significant localised intact rock damage up to 4 m from the blasthole (p = 0.007)preliminary point load test results indicate that blast damage results in a significant reduction in intact rock strength (p = 0.050)the significant increase in porosity and microfracture size associated with damage provides a mechanism for reduced intact rock strength due to confined blasting.CITATION:Stewart, P C, Brunton, I, Francis, D and Chitombo, G, 2016. Quantification of rock mass damage associated with a confined blast preconditioning experiment at the Cadia East block cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation.

Jan 1, 2007

By V. S. S. Yadavalli, J. Hager, R. Webber-Youngman

"This article investigates the complex problem of a budgeting process for a large mining operation. Strict adherence to budget infers that financial results align with goals. In reality, the budget is not a predetermined entity but emerges as the sum of the enterprise’s operational plans. These are highly interdependent, being influenced by unforeseeable events and operational decision-making.Limitations of stochastic simulations, normally applied in the project environment but not in budgeting, are examined and a model enabling their application is proposed. A better understanding of budget failure in large mines emerges, showing that the budget should be viewed as a probability distribution rather than a single deterministic value.The strength of the model application lies with the combining of stochastic simulation, probability theory, financial budgeting, and practical scheduling to predict budget achievement, reflected as a probability distribution. The principal finding is the interpretation of the risk associated with, and constraints pertaining to, the budget.The model utilizes a four-dimensional (space and time) schedule, linking key drivers through activity-based costing to the budget. It offers a highly expressive account of deduction regarding fund application for budget achievement, emphasizing that ’it is better to be approximately right than precisely wrong’."

Jan 1, 2015

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice-chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor. Candace Trimble, member SME, of Oil-Dri Corporation of America, is chair of the Industrial Minerals and Aggregates Division?s Technical Committee.

Jan 1, 2012

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015