Search Documents

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By Tony Brunger, Abid O. Adekunte, George Munteanu, David Greentree

A number of novel solutions have been proposed in recent years as alternatives to props and tie-backs in deep excavation support e.g. Adekunte (2008), Deschamps et. al. (2008), Adekunte et al. (2010) and Adekunte (2014). A number of these non-standard restraining solutions involve the construction of permanent or temporary vertical or raking buttress piles that are rigidly connected to the excavation support wall at regular intervals along the wall run. This paper chiefly focuses on the design and construction of twin-vertical buttress piles as restraining systems behind or in front of embedded retaining walls. The system essentially relies on the push-pull mechanism that develops between the twin piles, to maintain the overall stability of the excavation support. The paper’s main areas of concentration include; finite element modelling, geostructural design, construction procedure, instrumentation and monitoring that are associated with the application of twin- buttress pile systems. These are supported with project details of three recently completed high-end luxurious residential developments in Greater London, England, on which the twin-buttress pile system was used to restrain the excavation support walls for the basements on the sites. The mode of application of the system varies across the three sites. While the system was adopted as a long term solution behind the retaining wall on one of the sites, it was designed and constructed for temporary use in front of the retaining walls on the other two sites. Instrumentation and monitoring results from all the sites show the non-traditional system to be safe and effective, whilst having significant beneficial effects on construction programme, sequence of works and project cost.

Jan 1, 2018

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By Jewel A. G. Gomes

Electrocoagulation (EC) has been performed with Al-Fe electrode system with changing polarity for the removal of arsenic from water. The removal process has been studied using ICP-AES and Anodic Stripping Voltammetry with a wide range of arsenic concentration (1-1000 ppm) at various pH (4-10) and residence times (1-60 min). Electrochemically generated by-products have been analyzed using XRD, FTIR, XPS, SEM/EDS and Mössbauer Spectroscopy. Results revealed expected crystalline iron oxides (magnetite (Fe3O4), lepidocrocite (FeO(OH)), iron oxide (FeO)) and aluminum oxides (bayerite (Al(OH)3), diaspore (AlO(OH)), mansfieldite (AlAsO4?2(H2O)), as well as some interaction between the phases. The amorphous or ultra-fine particular phase was also found in the floc. The substitution of Fe3+ ions by Al3+ ions in the solid surface has been observed, indicating an alternative removal mechanism of arsenic in these metal hydroxides and oxyhydroxides by providing larger surface area for arsenic adsorption via retarding the crystalline formation of iron oxides.

Jan 1, 2006

By Thomas P. Mucho, Dennis R. Dolinar, Anthony T. Iannacchione

The Chestnut Ridge Anticline is a prominent structure in southwestern Pennsylvania, USA. This structure has brought two economically valuable limestone formations to the surface, where they are easily accessible to room-and-pillar mining. Nine active crushed stone quarries, an underground research facility, and one industrial facility currently operate along the linear trend that represents the axis of the anticline. The National Institute for Occupational Safety and Health (NIOSH) has identified significant variation in levels of horizontal stress within relatively short distances at shallow overburdens along the anticline. At one quarry, the horizontal stress is high enough to shear strata with a modulus of approximately 77 Gpa. Conversely, zones of extension were observed in parts of another quarry, indicating very low horizontal stress conditions. This study found that high levels of horizontal stress are to be expected in this very stiff rock formation and that local geologic and topographic structures are capable of altering the magnitude and possibly the orientation of the horizontal stress field.

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By David S. Yang

The Cement Deep Soil Mixing (CDSM) method introduces and mixes cementitious materials with in situ soils using hollow-stem rotating shafts equipped with a cutting tool at the tip and mixing paddles above the tip. CDSM generally produces a soil-cement panel consisting of three overlapping soil-cement columns. The soil-cement panel is then extended to form walls, which are effective for excavation support and groundwater control due to the continuity and low permeability of soil-cement walls. Two design approaches could be taken in the application of CDSM for excavation support: 1) single wall design and 2) gravity wall design. The former one is treated as a wall technology and the latter one is treated as a soil stabilization method. This paper will review the CDSM equipment and installation procedures for the construction of these two types of soil-cement walls. Four case examples are used to illustrate the design and application of these two types of soil-cement walls.

Jan 1, 2003

By Robert E. McIvor

The Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

Flawed mining studies have been major contributors to poor investment decisions in mining for many years, contributing to the long period of poor industry profitability. Most of the major mining houses have now adopted quite formal processes and quality standards for mining studies to reduce the potential for poor investment decisions in the future. Other organisations such as the World Bank also have specific requirements for particular types of studies, such as bankable studies. This increasing requirement for rigour and discipline means a highly structured and phased sequence of studies is now required along with the development and adoption of industry-wide standards in mine ventilation studies. New terms in the study process such as ?independent peer review? and ?hold and review? are assisting in this process. More traditional terms such as ?feasibility study? and ?pre-feasibility study? now have much more precise technical definitions. Specific standards for the ventilation components of the various phases of a mining study are proposed in this paper.

Jan 1, 2009

By Jason M. Ryan, T Michael LeBlanc, John H. Heiiig

Drill trajectory deviation is a recurring problem in the Mining Industry retreat stoping operations. As a result of this deviation, it is quite concevable that 60 kg (165 mm 0) and 103 kg (203 mm 0) explosive charges are detonated beyond the hanging wall contact. Consequently, there follows a reduction in hanging wall stability and an increase in ore dilution.

Jan 1, 1995

By A. Sobhy

Froth flotation is a widely used, cost effective coal cleaning process. However, its high process efficiency is limited to a narrow particle size range between approximately 50 to 600 µm for coal and 10 to 100 µm for minerals. Beyond this range, the efficiency of froth flotation decreases sharply, especially for difficult-to-float coal fines of weak hydrophobicity (e.g., oxidized coal). This study was aimed at enhancing recovery of an Illinois fine coal sample using a flotation column featuring a hydrodynamic cavitation nanobubble generator. Nanobubbles that are mostly smaller than 1 µm can be formed selectively on hydrophobic coal particles from dissolved air in fine coal slurry. Results indicate that combustible recovery of a -150 µm coal was increased by 5-50% for different size fractions in presence of nanobubbles, depending on process operating conditions. Other major advantages of the nanobubble flotation process include lower collector dosage and air consumption since nanobubbles are produced from air naturally dissolved in water and they act as a secondary collector on particle surfaces, thereby resulting in considerably lower operating costs. Key words: Cavitation; coal; froth flotation; nanobubble.

Feb 27, 2013

By G. S. Austin

The St. Cloud Mining Company extracts clinoptilolite about 6.5 km south of Winston, Sierra County, New Mexico. Production is about 18,000 mt/year. Natural zeolites are good adsorbents for positively charged solutes such as ammonium. St. Cloud’s production is used in animal hygiene, animal feed, environmental mitigation, air and water filtration, and other applications. By a simple chemical treatment with a surfactant, zeolites can also be modified to adsorb negatively charged solutes such as nitrate and arsentate, and neutral organics such as solvents and fuel components. These surfactant-modified zeolites are used in treating groundwater contamination, stormwater runoff, and solvent vapors from painting operations.

Jan 1, 2002

By Seokbin Lim

In the design of explosives devices, an understanding of the behavior of explosively propelled matter is one of the most important steps in maximize the performance of these devices. For instance, an explosively driven metallic liner in LSCs (Linear Shaped Charges) creates its functional effect of penetration after a finite distance of travel (before collapse), thus the detailed study of the projection mechanism of the flat liner after detonation helps in the optimization of the design of LSCs. In a typical metallic flyer driven by explosive detonation, the detonation gas propels nearby matter including flat flyers. After a certain degree of expansion in the detonation gas, the flat flyer reaches its maximum velocity and slows down afterward. These typical behaviors are well investigated and numerically studied by many researchers. However, the rarefaction intrusion (detonation gas expansion) near the surface of the explosive charge creates significant deformation of the flat flyer , and produces U-shaped bending or deformation near the edge of the flyer during projection, creating unexpected behavior in explosive devices of interest. In this paper, a preliminary investigation of a localized Ushaped deformation of flat metallic flyers during projection is studied utilizing a theoretical approach and computational modeling facilitating an understanding of a general tendency of the deformation behavior.

Jan 1, 2010

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

By Göran Bäckblom

The Swedish mining companies LKAB and Boliden, the equipment supplier Atlas Copco, the general contractor NCC and the specialist company Reflex joined forces in 2005 to advance the field of rock technology for the purpose of mining and underground construction. The creation of the company Rock Tech Centre is part of the strategy developed by the Swedish mining industry to strengthen co-operation with industry, academia and society. This paper outlines the current R&D strategies developed for the industry in general, discusses what focus areas are selected and provides some details on the current RTC project portfolio, especially faster and better drifting.

May 1, 2006

By J. Egan

The recovery of gold by ore leaching is influenced by the size of the particles and the chemical environment. Within the experimental error associated to the testing of gold ore, results of a series of leaching tests conducted with natural ores rather than monosized samples confirm that gold dissolution increases with decreasing ore particle size. The tests also indicate that the dissolution of gold in the ore within a size interval is weakly affected by the intensity of the size reduction method.

Feb 27, 2013

By Hart G. H

In tectonically disturbed zones within coal seams, decreases in the amount of kaolinite in the cellular structure of inertiniterich coal are accompanied by increasing kaolinite contents in fractures within the coal and/or rocks of immediately overlying horizons. This is due to fracturing of the inertinite microstructure by tectonic disturbance and remobilization and redistribution of free, fine-grained material (kaolinite and/or inertodetrinite.) Ascending waters are believed to transport the kaolinite in suspension, and redeposit it in the fractures and pores in the overlying horizons. This removal of material from the inertinite-rich coal leads to an increase in porosity (higher free gas storage), a presumed reduction in coal strength and an apparent increased proneness to instantaneous outbursts of coal and gas.

Jan 1, 1983

By P Mulvey

"Currently mine process studies and geochemical waste characterisation are considered as two interdependent studies, necessary for the development of the mine and inclusion in the environmental impact statement (EIS). Geochemical waste characterisation will utilise the simulated tailings produced by the mine process studies team to understand the behaviour of the tailings, but the two teams rarely integrate these to develop a coherent and agreed final design.Thorough mine waste geochemical assessments can develop processes to minimise environmental harm, resulting in substantial savings in the decommissioning, closure and rehabilitation phases, and may also be able to address changes in mineral processing methods that can result in substantial savings in process inputs, or even recovery of metal concentrates.Based on geochemical waste characterisation, the full cost of waste management can be calculated and incorporated into the costing of milling.  This allows for a more effective evaluation of the metallurgy.  A number of examples are presented in which substantial improvements have been made from the collaboration of both the metallurgical and geochemical teams during planning and the metallurgical team and environmental team during operations.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Optimising metallurgy at the planning stage to minimise environmental impact - a feedback loop from geochemical waste characterisation, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013