Search Documents

By E. H. Erwin Gartner

The Rhenish lignite deposit in the Nordrhein-Westphalia province of the German Federal Republic covers an area on the left bank of the Rhine River of about 970 sq miles (Fig. 1). Here, in the Miocene era, some 20 million years ago a lignite seam was formed and later broken, through tectonic movements into several blocks, some thrown down into depths of over 1,500 ft. This deposit consists of a single seam, in places up to 300 ft thick, but averaging about 150 ft. In a few areas, it is split into as many as five seams, separated by barren strata. It contains about 60 billion tons (2000 lb/short ton) of lignite which, however, being relatively young geologically, has, because of approximately 60% moisture, 2 to 8% ash, and low sulfur, a net calorific value of 3,340 Btu. That calorific value increases, however, with rising thickness of the cap rock. About one-third of the yearly production of 90 to 100 million tons of raw lignites is converted into briquets. Raw lignite is pulverized and dried to about 18% water content and then pressed without binder into briquets under a pressure of about 14,000 psi. The briquets are being used primarily for residential heating; their sales, however, have been declining sharply since 1963. On the other hand, the volume of raw lignite used in steam power plants has been rising steadily and amounts at present (1968) to about two-thirds of the total production. Huge steam power plants, such as Frimmersdorf, shown in Fig. 2 (which, with an installed capacity of 2,600 MW [megawatt], represents the world's largest steam power plant) with a generating capacity of up to 300 MW per unit and a total installed capacity of over 6,000 MW, contribute about 26% of the total electric power production of the German Federal Republic.

Jan 1, 1969

By RENARDIR PEIXOTO MACIEL JUNIOR

Tratamentos térmicos são de grande importância para o desenvolvimento dos materiais, pois alteram as suas propriedades ou conferem-lhes características determinadas. Neste trabalho, foram realizados dois tratamentos térmicos diferentes, recozimento pleno e normalização, em um aço utilizado como eixo de sustentação de aerogerador a fim de verificar as alterações nas microestruturas e propriedades mecânicas através de microscopia ótica, microscopia eletrônica de varredura e ensaio de microdureza Vickers. Além disso, foi realizada a identificação do material por meio de cálculo de composição de carbono utilizando o programa Image J com imagens obtidas por microscopia ótica. Logo, determinou-se que o aço tinha um teor de 0,55% de carbono. Após o estudo comparativo de dureza, verificou-se uma maior dureza da amostra normalizada e uma menor para a amostra recozida em comparação com a amostra recebida (sem tratamento). Logo, alcançaram-se os objetivos esperados ao fim do trabalho, pois todas as etapas foram realizadas com êxito obtendo,dessa forma, uma análise de resultados precisa.

Oct 30, 2017

By Luana De Lucca de Costa

O forjamento a quente em matriz aberta é, atualmente, o processo mais utilizado para a fabricação de peças de grande porte. Neste estudo, a simulação numérica foi utilizada, através do método de elementos finitos, para análise do processo de forjamento em matriz aberta de um eixo vazado e escalonado aplicável em aerogeradores. A partir de um billet cilíndrico vazado de aço AISI 4140, pesando 1 kg, é simulado o processo de forjamento objetivando a obtenção de geometria final apresentada. Utiliza-se matrizes superior e inferior em formato côncavo, e um mandril de manipulação com inclinação de 1,15°. A cinemática da simulação numérica, que inclui 4 passes com um número total de 30 cursos, é avaliada. Ao comparar a geometria apresentada com a obtida observa-se que o alongamento longitudinal da forma final é obtido. A partir da análise da temperatura, pode-se concluir que o reaquecimento deve ser realizado após cerca de 45 s, no final de cada série de 5 cursos.

Aug 8, 2018

By R. E. Wade

THE Butte, Anaconda & Pacific electrification is of peculiar interest, in an incidental way, to the entire mining fraternity, and especially the engineering branch, not only in this great Northwest country but throughout the entire Western mining country, which is rich in minerals and water power. It is probably fair to say that the prime object of mining and smelting engineering is to reduce the cost of production, and in the case in hand the relative location of mines and smelter brings the cost of transportation of ore to the front. While some might assign this item to the railway people, it is inseparably a part and parcel of the general scheme of the production of metal from the ore. In considering the electrification of the B., A. &. P. railway the mining and smelting engineer, above all, wants to know what saving will be effected by the change in motive power. Unfortunately the new power has been in use during a very limited period and on the Smelter Hill section of the road only, and no reliable data, from actual service conditions, can be obtained until the entire electrified section has been in service for a reasonable length of time. Any remarks on this subject at the present time, therefore, must of necessity be general in nature and more or less descriptive. The railway, electrical and mining worlds and the country in general are indebted to the B., A. & P. railway for the pioneer work it is now doing, as it undoubtedly marks the beginning of the electrification, within the comparatively near future, of all transcontinental roads between the Missouri river and the Pacific coast. Together with this goes the development of an untold wealth in water power and all natural resources within the same territory. For the first time in the history of electric railway work, in this country, direct current at a potential of 2,400 volts is being used. With this potential there is a great saving in transmission of energy to the locomotives and there are only two substations, one at. either end and 26 miles apart, for supplying the power for the movement of trains of heavy tonnage over the main line and for switching movements at terminal and intermediate yards, and comparatively little feeder copper is required.

Jan 11, 1913

By J. C. Motz

During the past five years, Rexnord has developed, tested and introduced the Nordberg Omnicone Crusher to the industry. When the Symons brothers invented the cone crusher over 60 years ago, they employed the principle wherein the length of the crushing stroke was related to the free fall of material by gravity. This permitted the material being crushed to fall vertically in the crushing chamber; and in effect, caused the particles to be crushed in a series of steps or stages as the particles got smaller due to the crushing action. This also helps to reduce the rate of wear of the liners since the sliding motion of the particles is minimized.

Jan 1, 1986

By B. S. Kim, Y. D. Kim, T. S. Kim, T. B. Kim, H. J. Chae

"The Nd-Fe-B scrap was placed in Fe crucible with pure Mg in an Ar atmosphere, and the scraps were melted using an induction heating method. The effects of experimental parameters such as melting temperature (range of 993K to 1073K) and holding time (15min-600min) on the ability of extraction were investigated. The microstructure and diffusion layers were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), and the constituent phases were characterized using XRay Diffraction (XRD). Diffusion of Nd through the Nd-Fe-B scrap into liquid Mg was described, and the diffusion coefficient of Nd in liquid Mg was estimated.INTRODUCTIONNd-Fe-B magnets are usually produced either from comminuted melt-spun ribbons as bonded magnets or hot pressed bulk magnets, or by sintering in conjunction with prior green compaction in an applied magnetic field (Sagawa et al., 1984). These magnets have been widely used for various electromechanical and electronic devices such as voice coil motors (VCMs) and magnetic resonance imaging (MRI) (Samardzija et al., 2012; Matsuura et al., 2006). The production of the Nd-Fe-B magnets is increasing by about 20% per year because of their excellent magnetic properties. However, the expansion of Nd-Fe-B magnet market induced a concern for the scarcity of Nd at the aspect of natural resource. Therefore, the development of an effective recycling process for Nd-Fe-B magnet scraps is an extremely important issue from the viewpoint of resource and energy conservation. Several recycling processes for the Nd-Fe-B magnets have been proposed (Uda et al., 2002; Lyman et al., 1993]. It has been reported that the best separation of rare-earths from the Nd-Fe-B magnets is obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. However, this process can make a large amount of waste water including dangerous solutions. Recently, (Xu et al., 2000) have reported a technique to extract Nd from 18Nd-72.4Fe-0.9B-1.82Pr-5.3Dy (wt.%) magnet scrap by using liquid metal extraction (LME) processing. However, these techniques seemed to be difficult for application, because the scraps consist of an infinitesimal amount of other minor elements (Pr, Dy, Cu, Al and Tb), and these minor elements can make a new intermetallic compounds with Mg. Also, some oxides or the plated Ni metal can be preventable to reaction between solid-liquid (S/L) interfaces. For these reasons, the substantive reaction mechanism between Mg and Nd-Fe-B scrap is not clear. In this study, the simple composition of 33Nd-66Fe-1B (wt.%) magnet scraps were prepared using an induction melting process. The effects of the experimental parameter on the diffusion properties between Mg and scraps were investigated to determine whether these methods could be used in industrial application in a liquid metal extraction (LME) process."

Jan 1, 2012

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

By Marcela dos Passos Galluzzi Baltazar

Catalisador monolítico comercial de níquel foi selecionado com o objetivo de se determinar o regime cinético da reação de oxidação parcial do metano (OPM). As estruturas cristalinas deste catalisador foram identificadas por DRX. A composição química superficial e o estado químico dos elementos presentes na superfície da amostra foram determinados por EDX. A técnica de microscopia (MEV) com emissão de campo foi utilizada neste trabalho com as finalidades de análise morfológica do catalisador antes de sua utilização nas reações de oxidação parcial. Análises de TG-DTA foram realizadas com o objetivo de se estudar o comportamento térmico do catalisador. A área superficial e a área metálica foram determinadas por BET e Quimissorção, respectivamente. A temperatura de redução do catalisador foi determinada através de TPR. Foi utilizada uma unidade experimental para realização de testes catalíticos. Antes das reações, os catalisadores pulverizados na faixa granulométrica < 0,150 mm foram submetidos a uma etapa de redução para ativar os sítios de níquel metálico. As análises dos produtos de saída do reator e das cargas reagentes foram realizadas por cromatografia gasosa, utilizando-se um Cromatógrafo VARIAN CP3800. Foi determinado o regime cinético na OPM utilizando as massas de catalisador 65, 80 e 95 mg.

Oct 30, 2017

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By E. J. Lintner, J. R. Thoenen

During the period 1937-40 and until peacetime research was superseded in 1941 by wartime activities , the junior author was engaged in studies regarding the relative efficiency of operating methods in quarries producing crushed stone for mineral aggregates . The results of some of these studies were published as reports of investigations in 1939 and 1940 ; / others were discontinued due to war demands on personnel and time . The published reports discussed the efficiency of particular quarry operations with respect to the time consumed and without reference to costs or mechanical factors . • At the time , the field data were collected for the published reports other data were collected relative to the relationship of the numerous variable factors inherent in the operation of a churn drill to the ability of the drill to produce blast holes . The churn drill is essentially a crusher and depends. for its performance upon the foot-pounds of energy it can impart to the cutting edge of its bit . The gravity stamp mill , so well-known in western gold mines , is essentially the same type of crusher . The ratio of foot- pounds necessary to crush the rock , to the total theoretical energy developed by the falling churn- drill tools , affords a good means of evaluating the efficiency of the tool . This does not include to tal over-all efficiency involving the mechanical equipment of the drill itself or its power unit .

Jan 1, 1947

By T J. Callaghan

The Avebury nickel mine in Western Tasmania is a disseminated nickel sulfide deposit hosted in intensely metasomatised Cambrian ultramafic resulting from later Devonian granite related hydrothermal activity.Variable metasomatism of the ultramafic has formed two distinct gangue mineral assemblages. Less metasomatised ultramafic is comprised of fine grained black antigorite with minor disseminated chromite, magnetite and pentlandite. Intensely metasomatised ultramafic is altered to a pale grey or green, coarsely crystalline tremolite/actinolite and diopside assemblage with minor magnetite, chromite and sulfides. Both gangue mineral assemblages are frequently intermixed in ore grade mineralisation.The bimodal gangue of either serpentinite or metasomatised ultramafic presents challenges to drilling, mining, resource estimation and mineral processing as they possess very different physical properties. Mineralised serpentinite has a mean bulk density of 2.8 g/cc and the ultramafic skarn a mean bulk density of 3.2 g/cc. Physically, the ultramafic skarn is hard to break percussively creating difficulties in the crushing circuit and reducing mine development rates. However, it is non-abrasive and grinds readily, resulting in increased diamond drilling rates and increased mill throughput. Conversely the serpentinite gangue is softer and breaks easily resulting in accelerated development rates and crushing circuit throughput. However, its fibrous nature reduces grinding efficiency, increasing bond work indices and reducing diamond drilling rates.Predicting the ratio of serpentinised to metasomatised ultramafic is possible through use of the resource blockmodel, assisting mine scheduling, predicting mill throughput rates, energy consumption and grade control drilling rates.CITATION:Callaghan, T J, 2017. Challenges of bi-modal gangue mineralogy in mining geology, in Proceedings Tenth International Mining Geology Conference 2017, pp 23–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By André Pereira Barbosa

Este projeto tem como objetivo desenvolver o uso do transporte multimodal nas operações de entrega de produtos via cabotagem, para as regiões Norte e Nordeste, em sinergia de todas as usinas da ArcelorMittal no Brasil. O trabalho visa demonstrar os principais dificuldades e benefícios da utilização da cabotagem. O projeto foi subdividido em etapas de implantação, que se iniciou com um processo de contratação, envolvendo os fornecedores de cabotagem e serviços de ovação para as operações das unidades de Longos (Cariacica, Sabará, Itaúna, Juiz de Fora e Piracicaba) e de Planos (Tubarão) de forma conjunta buscando uma melhor condição comercial e contratos sólidos de atendimento, com foco na utilização das mesmas estruturas de terminais, portos, fornecedores e até containers. Foi estimada uma redução significante dos impactos socioambientais e dos custos de fretes para organização.

Aug 17, 2017

By Foluke Salgado de Assis

Este trabalho visa apresentar os resultados obtidos através de ensaios balísticos realizados em sistemas de blindagem multicamada. Seguindo as especificações da norma americana NIJ 0101.06, foram realizados ensaios utilizando munição de calibre 7,62x 51 mm, que possui velocidade acima de 800 m/s. A blindagem multicamada utilizada possui como camada frontal uma pastilha hexagonal cerâmica (alumina dopada com 4% de nióbia), segunda camada de compósito de matriz poliéster reforçada com tecido de juta e como terceira camada uma placa de alumino 5052 H34. A utilização de compósitos poliméricos reforçados com fibras naturais em substituição às fibras de aramida é de grande interesse, pois além de desempenharem a mesma função no sistema de blindagem, possuem um valor de mercado bem menor. Os resultados de profundidade de indentação na plastilina foram satisfatórios visto que atenderam a norma NIJ 0101.06 e utilizando a técnica de microscopia eletrônica de varredura, verificou-se que o compósito poliéster-juta capturou os fragmentos através do mecanismo de incrustação mecânica.

Aug 17, 2017

By Carl F. Wingquist

In support of Bureau of Mines studies of thermal fragmentation of rock, the elastic moduli of four types of rock were measured at temperatures ranging from room temperature up to 1,500° F (1,089° K). The sonic method was employed to determine the resonant frequencies of the rock specimens and from these frequencies, the elastic moduli were calculated. Data for Young's modulus, shear modulus, and Poisson's ratio are given as a function of temperature for Dresser basalt, Reserve taconite, Jasper quartzite, and Charcoal granite. Young's modulus and the shear modulus decreased with increasing temperature up to about 1,200° F and then became relatively insensitive to temperatures from 1,200° to 1,500° F.

Jan 1, 1969

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

By Camilo José de Freitas Neto

O objetivo deste trabalho foi estudar a variabilidade do depósito de zinco sulfetado do projeto Ambrósia Sul, da Votorantim Metais localizado em Paracatu - Minas Gerais, frente aos processos de beneficiamento e poder, assim, detalhar o comportamento geometalúrgico dos vários corpos de minério do depósito. Além do estudo da variabilidade dos corpos de minério, o trabalho também inclui testes em escala de bancada durante anos e semestres de operação: 2016, 2017/01, 2017/02, 2018/01, 2018/02, 2019. A metodologia do estudo é resumida nas fases de amostragem de testemunho de sondagem, composição das amostras representativas dos corpos de minério e anos e semestres de operação da mina, testes de moagem, peneiramento, flotação de bancada e caracterização mineralógica da alimentação e produtos dos testes. O teste de bancada desenvolvido neste trabalho, tem como objetivo principal verificar variações significativas entre os corpos mineralizados e/ou semestres de mina de operação, tornando possível identificar potenciais oportunidades de otimização do circuito de tratamento de minérios, maximizando o retorno financeiro de toda a jazida mineral.

Aug 17, 2017

By Thomas O. Llewellyn

This U.S. Bureau of Mines (USBM) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material flow for the year 1989. This preliminary study contains information on cadmium and cadmium-bearing products in the United States. The data in this report were obtained from both published and/or unpublished sources of information. However, in order to estimate the fate of cadmium in each operation or application stage, some assumptions, judgments, and correlations were made by the USBM in an attempt to determine the material flows losses.

Jan 1, 1994

By J. G. Kirby

The number of petroleum refineries in the United States continued to decline during 1954, and according to the Bureau of Mines annual survey there were 326 refineries with a total daily throughput capacity of 8,420,630 barrels, as of January 1, 1955. The increase in capacity for the year was 413,733 barrels daily, while the number of refineries declined 11. The capacity of the average refinery to process crude oil increased during 1954 from 23,759 barrels daily to 25,830. Breaking down the crude-oil capacity increase, by refining districts; 32 percent was installed at refin¬eries located in the Texas Gulf Coast district, 25 percent in the East Coast district, and 13 percent in both the Louisiana Gulf Coast and the California districts. The Appalachian No. 1, Texas Inland, and New Mexico refining districts reported declines in capacity during the year. Additional crude-oil capacity under construction, January 1, 1955, totaled 146,800 barrels daily. Included in this total are 4 new refineries, 1 each in California, Minnesota, New Mexico, and Washington. In addition to the' new facilities, equipment producing 1.49,550 barrels daily is being replaced.

Jan 1, 1955

By J. F. Shaw

MINE fires are usually extinguished by constructing seals in the approaches to the areas to exclude air from the fire areas, which smothers the fires in an oxygen-depleted atmosphere. Seals should be substantially constructed and made as nearly airtight as possible and should be provided with a sampling pipe so that samples of the atmospheres behind the seals may be collected at regular intervals. Methods of constructing seals and of sampling and analysing mine atmospheres are fully described in Bureau of Mines publications. (1, 2). Information obtained on the composition of atmospheres behind fire seals is helpful in determining if a fire has been extinguished or if there is any danger of an explosion when a fire area is being sealed or unsealed. The progress of a mine fire can best be determined by studying percentages of carbon dioxide, carbon monoxide, and hydrogen in the atmosphere behind the seals. Hydrogen will be formed in a bituminous- or subbituminous-coal mine when the temperature exceeds 480° F. and in an anthracite mine when the temperature exceeds 660° F. (3). Carbon monoxide and carbon dioxide are both products of combustion of coal, wood, or other organic compounds. The presence of carbon monoxide has long been accepted as an indication of a mine fire. A sealed fire area should not be reopened until the carbon monoxide has disappeared. Trends in the percentage of carbon dioxide are also useful in determining the status of a mine fire. Carbon dioxide is sometimes liberated by rock strata. In this case, carbon dioxide in the atmosphere behind a seal will be from two sources-the rock strata and the fire. When the, fire is extinguished, carbon dioxide will be liberated from only I source, the rock strata, and when the percentages of carbon dioxide are plotted, the slope of the curve will not be as steep as when this gas was being liberated from 2 sources. If the only source is the fire, the percentages of carbon dioxide will gradually decrease after the fire has been extinguished. By studying analyses of a mine-fire atmosphere, it is possible to determine if the atmosphere is explosive; if the mixture is capable of becoming explosive when mixed with air; and if the mixture can be made nonexplosive or be prevented from becoming explosive by being mixed with an inert gas. These factors can be computed mathematically or determined graphically. The mathematical calculations advanced by Ash and Felegy (7) are discussed, and graphical solutions of their equations are presented. It is believed that the graphical solution will be extremely helpful in determining the characteristics of a mine-fire atmosphere when fighting a fire, because the results can be obtained in a matter of minutes, and there is less likelihood of an error being made under the stress incident to control efforts. The experimental and theoretical work upon which the formulas are based have been adequately described and are not discussed at this time (5) (6).

Jan 1, 1955