Search Documents

By M. J. deBastiani

The uranium producing division of Denison Mines Limited operates a 6,000-ton-per-day integrated mining unit in the Algoma area of Ontario. The property is located approximately one and one-half miles from Highway I 08, eight miles north of the town of Elliot Lake. The property was staked in 1953, diamond-drilled in ?late 1954 and 1955, and put into production in 1957. Since that date, the operation has produced $250,000,000 worth of uranium oxide from approximately 11,000,000 tons of ore milled, and paid $18,000,000 in dividends to its shareholders. The operation employs about I000 people, and monthly operating costs are approximately one million dollars. From these figures alone, it is obvious that it was necessary to develop and institute an adequate set ?of controls for effective management at all levels of supervision over a period of four years, a system of production and cost control was developed that enables us to effectively measure the pulse of the various phases of the operation at any given time.

Jan 1, 1963

By Parameswaran V. S, Anshuman Singh

This is a case study on ground improvement using Stone columns at Kokrajhar in Assam which comes under seismic Zone V as per IS: 1893. The strata at site comprised of mostly fine sands with low SPTN values, fine content less than 10% and ground water table (GWT) at shallow depth. As ground water table subjected to seasonal variation, water table is considered at ground level for designing purpose. The geotechnical profile of the boreholes was analysed on the guidelines of IS 1893 (Part 1) -2016 and it was observed that the liquefaction potential of the soil layers is prominent and ground improvement is inevitable up to a depth of 9.5 m below existing ground level. In order to mitigate the liquefaction of soil layer, Stone columns were proposed. The in-situ soil is densified using wet top feed vibroreplacement method with an area replacement ratio of 16%, so that the relative density of the soil can be enhanced to prevent liquefaction risk. Correlation between relative density, fines content and increment of SPT N –value given by Tokimatsu and Yoshimi (1983) was used for designing purpose. Field tests such as SPTs were carried out at site to validate the extent of SPT (N) improvement. Detail comparison of pre and post density, SPT N values and CRR values were discussed in this paper.

Nov 1, 2022

By D. F. Suarez

Spontaneous nodulation leading to growth of well developed glossy spheroids (generally hemispheres) of up to 0.06 cm width in 120 min has been observed during copper electrodeposition with certain levels of glue, thiourea and C1-. Thiourea alone can produce spontaneous nodulation but addition of glue and/or Cl- is required for rapid and sustained growth. In most cases once the glossy nodules develop they consume the majority of the copper deposited; thus, the specific current densities (and hence copper electrodeposition rates) on the glossy nodules are about an order of magnitude or, more greater than on the adjacent planar surfaces. The texture of the adjaoent planar surfaces is not glossy in appearance but is well faceted showing the usual deposition grain structure for such additives. Cathode potentials when spontaneous nodulation occurs are about TOO my more negative than with usual copper electroplating. This fact associated with evidence of extremely high levels of cathode surface passivation based on cyclic voltammograms indicates that the conditions which lead to spontaneous nodulation result from a very tightly adsorbed additive surface film. This film breaks down in specific points initiating the glossy nodules which then grow at extremely rapid rates. Current density is also important in spontaneous nodulation. At equal deposition times a current density of 21.5 mA/cm produced much larger glossy nodules than at 48 mA/cm2. The surface concentration of the glossy nodules was much greater in the latter case, however. The role of current density is still not well understood. The role of it as well as the relative roles of the three additives, thiourea, glue and Cl- in spontaneous nodulation is presented. Preliminary results and some possible correlations of these to help explain spontaneous nodulation are presented. It is believed that tankhouse upsets where cathode nodulation occurs may be related to this phenomenon.

Jan 1, 1987

By A. R. G. Azevedo, G. C. Xavier

"The search for technological innovations in the Civil Construction takes as an objective the reduction of costs and increase of the productivity. However, these technologies demand analysis and studies of parameters of control that provide the quality of the products. With the intention of improve the knowledge on industrialized mortars used in mechanized projection machines, a characterization was done in the state anidro, fresh and hardening of three mortars, being each one of a State, Rio de Janeiro, Sao Paulo and Bahia. The tenors of water/ mortar was obtained through tests done in built environment, it varied from 0,17 to 0,26. From these results, the mortars were projected by his respective consistency, analyzing its compressive strength, and traction adherence resistance, in this way, the good performance of the revetments was provided.IntroductionThe market competitiveness of Construction has led companies to invest in construction processes and techniques in order to rationalize and optimize the buildings. Thus, changes emerged in coating system providing improvements in conventional materials and novel construction techniques, such as mortar industrialized and mechanized projection.Adopting projection equipment mortar is flagged as one of the solutions to reduce the interference of hand labor in construction, optimizing the performance of internal and external coatings, as well as streamline the production process and transportation, reducing lossesMaterials and deadline for execution of the casing(l)The process has been used due to its benefits, however, studies are necessary parameters for quality control of these mortars used in the projection to greater knowledge of mixing and market acceptance. It is therefore quite relevant information processing techniques available on the subject, as necessary to carry out research aiming at defining specific indicators of quality."

Jan 1, 2013

By Jun Lu, Min Chen, Wei-jian Su, Jian-zhong Luo, Yu-tao Lei

"In the case of treating phosphatizing wastewater containing zinc, zinc had an impact on the solution chemistry, especially on pH. Fe2(SO4)3 and CaCl2 were used as precipitators to remove phosphate from zincic phosphatizing wastewater and the optimum pH was investigated. Zinc ion had a significant effect on the optimum pH. The optimum pH ranges were 12.10(inlet concentration of 15.67mg/L, outlet concentration of 9.53mg/L), 3.04-5.50(inlet concentration of 11.97mg/L, outlet concentration of 0.44-0.26mg/L), and more than 10.72(inlet concentration of 12.24mg/L, outlet concentration of less than 0.47mg/L) under the conditions without precipitator, with Fe2(SO4)3 and with CaCl2 respectively.Introduction Phosphate coating is commonly used for protective coating of machine elements. Including oil removal by caustic washing, rust removal by acid washing, phosphatization and inactivation, the phosphatization process produces wastewater containing inorganic salt of high concentration, especially the phosphate, beyond the environmental standards and polluting environment seriously. What’s more, the wastewater from zincic phosphatizing technology also contains another pollutant, zinc. At present, Chemical Precipitation (CP) and Biological Nutrient Removal (BNR) are two of most common technologies of phosphate removal. BNR, such as A/O, A2/O and UCT technology, is suited for wastewater containing organ phosphorus of low concentration and CP for wastewater with phosphate of high concentration [1]. Researches on CP treating wastewater containing phosphate of high concentration, mainly focus on adding quantity of precipitators[2-5] and coagulants[2-4] and the choice of technologies[3-9]."

Jan 1, 2008

By Nick Barton, Khosrow Bakhtar

Two plate load tests of 1 m2 area were per- formed in a pressure tunnel at the Rocky Mountain Pumped Hydro Project. Reaction for the 250 tons loading in this 10.5 meter diameter tunnel was provided by deeply anchored, diverging rock bolts, eight per load frame. Pressure build up to 2.5 MPa was provided by circular flatjacks. Rock deformation was recorded at depths of approximately 0.3, 0.9, 1.2, 1.8 and 3.3 meters using axially located multiple position borehole extensometers. The tests were performed in representative units of massive shale and thin to medium bedded siltstone. Stress was built up in four equal steps to 2.5 MPa, held constant for one week for creep monitoring, then unloaded, reloaded and unloaded over a period of one day. The most deformable unit was the massive shale which exhibited 1.3 mm of permanent deformation at the surface after the first loading and unloading cycle, which included 0.36 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 2.6 mm, following a maximum deformation at the surface of approximately 3.6 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 0.4 GPa when loading, and 0.3 GPa when unloading. The thin to medium bedded siltstone exhibited only 0.17 mm of permanent deformation at the surface after the first loading-unloading cycle, which included only 0.05 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 0.27 mm, following a maximum deformation at the surface of approximately 0.53 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 6.2 GPa when loading and 21.9 GPa when unloading.

Jan 1, 1986

By Jelena Milinovic, Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando J. A. S. Barriga, Bramley Murton, Adeline Dutrieux

"The active TAG hydrothermal mound is one of the largest and better studied. Due to its size (one of the largest, known so far, in the Atlantic Ocean) and concentration of specific economic valuable elements, it might be considered for future exploitation due the increasing demand for raw materials. However, the discovery of several large inactive sulfide mounds, some partially buried under sediments may relieve this pressure. Exploration for such occurrences can, together with geophysical exploration tools, be accomplished by mineralogical and geochemical studies of those sediments.INTRODUCTION AND GEOLOGICAL SETTINGThis study reports the results from sediment samples collected during the Meteor M127 cruise on the TAG hydrothermal area in 2016. The Trans-Atlantic Geotraverse (TAG) hydrothermal field (Mid-Atlantic Ridge, 26°08’N) is located 2.4 km east of the main rift valley at depths of about 3650 m. The TAG hydrothermal field stands as an example of a massive sulfide deposit on a low-spreading ridge associated with an active detachment fault (Humphris et al., 2015).Associated with the TAG hydrothermal field are metalliferous sediments/deposits that can reach several meters in thickness (Metz et al., 1988). These sediments/deposits can be formed by hydrothermal plume fall out (buoyant and nonbuoyant), massive wasting of hydrothermal edifices (sulfide mounds and chimneys) and authigenic mineralization (Gurvich, 2006). By studying the grain size, mineralogy and geochemistry of the sediments it is possible to identify each type of sediments and find their proximal or distal distribution. The location of the gravity cores studied here is distributed along sediment ponds near inactive hydrothermal mounds [Three mounds area (B)], actively venting low-temperature mound [Shimmering mound (A) and Mir zone (D)] and an area of sediment accumulation [Central area (C)] (Rona et al., 1993) (see Figure 1)."

Jan 1, 2017

By Ana Maria Pérez Ceballos

Os aços inoxidáveis duplex e superduplex são caracterizados por uma estrutura bifásica contendo ilhas de austenita precipitadas numa matriz de ferrita. Estes aços possuem boas propriedades mecânicas e boa resistência à corrosão. No entanto, estes aços podem apresentar fragilização por hidrogênio. No desenvolvimento deste trabalho se estudou a difusão e fragilização por hidrogênio de um aço inoxidável superduplex SAF 2507 nos estados como recebido e tratado térmicamente. Para avaliar a influência da microestrutura sobre a difusão do hidrogênio foram realizados ensaios de permeação electroquímica de hidrogênio. Observou-se que o coeficiente de difusão aparente aumenta em função da temperatura de recozimento. A influência de hidrogênio na resistência à fratura do material recozido a 1300°C foi estudada a partir de ensaios de tenacidade à fratura (CTOD). Determinou-se que a resistência à fratura do material diminui consideravelmente quando o mesmo é submetido a uma carga de hidrogênio. A presença de hidrogênio também modificou o mecanismo de fratura do material, observou-se uma fratura completamente dúctil no material que foi testado em ausência de hidrogênio e uma fratura frágil, caracterizada por clivagem, foi observada no material hidrogenado. Determinou-se que a fase austenítica pode ser fragilizada sob certas condições de carga de hidrogênio.

Aug 17, 2017

By A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach- solvent extraction process devised to cleanly separate the metal values, and produce acid sulphate liquors containing the metals. It is shown that 86 percent of the nickel and 95 percent of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible.

Jan 1, 1964

By G. S. Rice

[This paper describes preliminary tests at the Bureau's Experimental Mine to determine, under conditions that may prevail ira bituminous coal-mine heading, how small a quantity of fire damp may bring coal-dust into suspension and ignite to it. The results show that the explosion of as little as 150 cubic feet of an explosive mixture of gas and air containing 9 per cent natural gas may start a disastrous explosion Of coal-dust. This is a very small volume, of gas, to cause such a result. Let us suppose that this amount of exclusive mixture, was at the face of an entry which was 10 feet wide and the face was overcut to a depth of 6 foot and an upper layer of coal 2 1/2 feet thick had been removed, the recess so made would save a volume of 150 cubic feet. Furthermore, only 13 cubic feet of pure methane is needed in this volume to produce this 9 per cent explosive mixture.]

Jan 1, 1930

By John Nagy

Large-scale tests in the U.S. Bureau of Mines Experimental Coal Mine show that the explosion hazard of coal dust on shuttle-car roadways can be con-trolled by proper application of water, dry rock dust, a saturated solution of ammonium phosphate, or mixtures of water or the water-phosphate solution with rock dust. The experiments were made with loadings of 1.0 and 5.0 pounds of mine size coal dust per linear foot of entry, and with a 3-or 4-inch-thick layer of coal rubble on the floor, The data from the tests with mine-size coal and rubble are comparable. The water contents of the dust loading were determined from samples collected just prior to initiation of a gas-air mixture in an ignition zone at the face Dust samples were collected 1 inch deep from the coal-rubble deposit. One experiment was made with the dust in the coal rubble bound with latex applied as a water solution by spray. The binding action was inadequate and explosion propagation was obtained.

Jan 1, 1970

By Akira Yazawa

In the field of pyrometallurgy, the equilibrium evaluation has recently become easy by use of thermodynamic software, but it is strongly desired to estimate the amounts of non-equilibrium minor components to simulate practical processes. However, simple physico-chemical technique can not be applied to evaluate practical non-equilibrium components for many reasons. As an engineering solution for postulated equilibrium system, the activity coefficient is modified and introduced as the simulation parameter referred to as the "adjustment coefficient." This modified thermodynamic calculations were adopted to various sulfide roasting processes where many solid phases are participating and the system is not necessarily in equilibrium. Successful simulation was realized by assigning suitable adjustment coefficients for minor components which form a pseudo solid solution in the calcine. Some examples from sulfation roasting and dearsenizing roasting were discussed. In the smelting system, the loss of copper in slag is caused by equilibrium and non- equilibrium reasons, that is, chemical dissolution and entrainment of copper in slag. The total copper content of slag was simulated by use of the adjustment coefficient for entrained copper.

Jan 1, 1998

By G. Venkateswara Rao

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of Iron ore fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of Iron ore fines. The results obtained from this study revealed that among the parameters studied, drum rotation, amount of wash water and angle of inclination play dominating roles in controlling the yield and grade of the Iron ore. The majority of the newly developed Multi gravity concentrators have tremendous potentials for various applications. Therefore, the performance evaluation of these concentrators treating various minerals, coals, heavy metal recovery from tailing dams, etc., have become an active research topic. Several attempts have also been made to develop appropriate mathematical models of individual concentrators. Despite all these efforts, these concentrators have yet to find the widespread applications they deserve. The ?as received? sample assayed 40.80% Fe, 40.90% SiO2,0.24% Al2O3and 0.20 % LOI and all other trace elements within the specified range. The current paper deals with the Mineralogical studies, characterization and process amenability studies of Sub grade Iron ore from Deposit No. 5, Bacheli complex of Bailadila using Multi Gravity Separator (MGS).

Sep 1, 2012

By Howard N. Eavenson

AN analysis of the bituminous coal situation by an authority who traces the production, mining, safety, markets and labor trends in comparison with other fuels. BEFORE 1918 the production of coal experienced a steady growth, with slight recessions in ouput in only twelve years (1837, 1841, 1852, 1855, 1861, 1874, 1876, 1889, 1894, 1905, 1909, 1914), and in each of these cases the loss was recovered in the following year and the increase continued. In each decade the output was doubled. Prices, while not high, allowed some profit. In 1918 during World War I, an output of 580 million tons was reached and with the exception of 1923 this total was not again reached until 1942, in World War 11. Losses of output in this period were much greater than ever before; in 1932 the total was 270 million tons less than in 1918 or 1923, and the loss after 1923 was not recovered until 1942. The greatest output was 631 million tons in 1947.

Jan 1, 1950

By Johne Jesus Mol Peixoto

A complexidade do formato do molde de beam blank aumenta a importância de se compreender o comportamento do fluxo no interior do mesmo. Neste estudo verificou-se a influência da profundidade de imersão e da velocidade de lingotamento sobre as características de fluxo em um molde de beam blank alimentado por duas válvulas tubulares. Os resultados das simulações matemáticas foram coerentes com os resultados do modelamento físico. A velocidade de espalhamento do jato na região do flange é maior que na alma e este fator pode acarretar na solidificação irregular da pele ao longo da seção transversal. A profundidade de penetração do jato variou entre 66cm e 77cm. A intensidade média de flutuação do menisco foi de 0,22mm, sendo a flutuação máxima encontrada de 0,85mm. Com base nos resultados obtidos, os parâmetros de operação sugeridos são: profundidade de imersão igual a 75mm e velocidade de lingotamento máxima de 1m/min.

Aug 17, 2017

By S. C. Gaillard

Tailings are made of ground rock that is left over from removing valuable minerals. The tailings are usually fine particles that cause environmental issues for storage and disposal. Disposal of tailings is a growing concern, as more tailings are produced from the increasing demand for mined material (ITRC, 2008). This project proposes a way to convert the mine waste to a useful product. Tailings were selected from a South Carolina crushed stone quarry, the products of which are used for road beds, sidewalks, asphalt and driveways. These tailings were processed to generate synthetic aggregates for construction applications. The synthetic aggregate creates a product that could be used for many purposes, including aggregate for sidewalks, driveways, roads and building materials. Testing methods followed the North Carolina Department of Transportation (NCDOT) guidelines for physical testing of coarse natural aggregate, which are sieve analysis, Los Angeles abrasion, absorption, specific gravity and soundness test. The synthetic aggregate produced passed all tests for NCDOT and, in some instances, rated better than a natural aggregate. Using the tailings from the crushed stone and mining industry would convert the waste into a valuable, marketable product.

Jan 1, 2013

By Walter Meintrup

On Nov. 4, 1981 the newly installed 1000tph wet-process iron-ore ball mill of A/S Sydvaranger completed its first four months of uninterrupted, successful full-load operation in Kirkenes/Norway. This 6.5m diameter mill is driven by a gearless ring or wrap-around motor of 8100kW at 13.1RPM - a first of a kind in this segment of industry. (Fig. 1) This paper analyses the reasons that have led to the selection of this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes in some detail the installation in Norway. General aspects of possible design variations, and application information for designers and users of such mills conclude the presentation.

Jan 1, 1982

By Weibai Hu

Four methods to assess the relative flotability of fine coal have been tested: flotation with frother only, flotation with frother and collector, salt flotation, and timed-release analysis. A practical and simple criterion which combines the separation efficiency (capacity factor and kinetic rate constant (intensity factor) has been suggested. Five coal samples are chosen and tested. Based on test results, it is concluded that the flotability test with collector and frother is closer to practice, and, according to the suggested flotability criterion, coal fines can be classified into four categories of relative flotability: very easy, easy, moderate, and difficult.

Jan 1, 1987

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By G. Caetani

I. INTRODUCTION. WE owe to the courtesy of Mr. R. M. Raymond, Manager of the El Oro Mining & Railway Co., Ltd., the permission of publishing in this paper the results of a series of experiments and tests made in view of determining the economical limit to which the fine grinding of the ore by tube-mills could be carried on. For the sake of clearness, the following definitions are given of certain terms used in this paper, as well as of the units and screens in the experiments. Slime : In a general way " slime" is that mill-product, of which from 90 to 95 per cent, will pass a 200-mesh screen (0.067 mm. aperture), and which is treated as one class of material in the El Oro cyanide-plants. As a screen-product, slime constitutes all material that *ill pass a 200-mesh, screen. In sizing, the following products are distinguished:- Coarse Sand : That material remaining on a 100-mesh (0.111 mm. aperture) screen. Fine Sand : That passing through. 100-mesh and remaining on a 200-mesh (0.067 mm. aperture) screen. Slime: That passing through 200-mesh. Fines, which pass through 200-mesh and settle in 30 seconds, and silt, which does not settle in 1 minute. Sand-index : The number proportional to its total fineness considered from the economical point of view, as explained on page 93. Absolute extraction : The percentage of values actually brought into solution. Actual extraction: The percentage of values actually brought to the ziuc-boxes. Units : Dollars, U. S. Currency; pounds; and short tons (2,000 lb.). Gold is valued at $20.67, and silver at $0.50 per ounce. Screens : In the sizing-tests the screens used were:¬ Mesh (per 1 in.), . 24 30 40 60 80 100 150 200 250 Aperture (mm.), . 0.740 0.515 0.424 0.250 0.159 0.111 0.090 0.067 0.058 Strengths of solution : Strengths are expressed in the percent- . age of KCN contained, though the sodium cyanide, which is

Jan 1, 1906