Search Documents

By Juan Kobashicawa, Bernardo Falcón

En este trabajo se explican los controles automáticos desarrollados (In-House) e implementados en el circuito de Molienda de Compañía Minera Antamina, el cual abarca Molinos SAG, de Bolas y los Hidrociclones respectivos. Los controles implementados son basados en el Control por Lógica Fuzzy y las Bandas de Bollinger; así mismo se indican los criterios en el diseño de los controladores y las variables del proceso que se han tomado para la implementación donde se controla un indicador de distancia del centro de masa de la carga respecto al centro del molino de Bolas. Asimismo, se muestra el impacto positivo logrado con la estabilización del circuito.

Sep 1, 2017

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003

By Erin Legault Seguin, Mike Rylatt, Curtis Mohns

"With energy costs increasing and ore grades diminishing, the role of pre-concentration in hard rock mining operations has been gaining greater interest. To maximize energy conservation, the pre-concentration process should be conducted at as coarse a crush size as possible while minimizing losses of pay metals. Dense medium separation (DMS) is a robust process that can be conducted at particle sizes as coarse as 300 mm and as fine as 500 µm with high separation efficiency, depending on liberation characteristics of the value minerals. The DMS process involves three steps: feed preparation, dense medium separation, and ferrous-based media recovery. This paper discusses each of these processing steps, but focus will be given to the dense medium separation stage. Various types of DMS equipment are reviewed. Pilot plant campaign case studies conducted at the SGS Lakefield site are presented, which have included a variety of mineral systems such as spodumene, sulphide-bearing gold ores, and complex sulphide ores. These case studies demonstrate that for amenable ores, mass rejection of 20-60% is possible while maintaining recoveries of greater than 90% in most cases.IntroductionPre-concentration is a process of rejecting mass of gangue while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Pre-concentration has been practiced in industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, typically requiring finer grind sizes and higher energy costs."

Jan 1, 2016

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

By John R. Goode

"The year 2011 witnessed a major surge in rare earth prices as China, supplier of +95% of the world’s rare earths, reduced export quotas and increased export taxes and duties. In response, companies around the world are scrambling for alternative sources. In Canada too, there is a race to be the “first” rare earth producer. Something that is not generally realized is that Canada has a long history of rare earth production and was a major supplier from the early 1960’s to 1990. At one stage, Canada was said to be supplying more than one third of the world’s yttrium and probably supplied even more than that. Five decades ago, thorium was a key element in many non-nuclear applications and Canada became a major supplier of thorium from the late 1950’s to 1968, first as a by-product of uranium and then as a co-product of rare earths. This paper reviews the development of Canada’s original rare earth and thorium production facilities, which were located in the Elliot Lake uranium camp in Northern Ontario. The uses of these elements, geology, mineralogy, markets of the time, and processing are all discussed. Some of the lessons learned from these pioneering operations might be useful in today’s race to develop the next generation of rare earth production plants.INTRODUCTION The rare earths and thorium were first identified in the early 19th century but were little more than curiosities for the next century. However, in the mid-1960’s the invention of rare earth-based phosphors for the cathode ray tube in colour television sets launched a major demand for certain rare earths. The use of thorium as an alloying agent in aircraft and missiles grew rapidly in the late 1950’s. In the same period, demand for uranium for both weapons and power production soared. Also in the late 1950’s, the Elliot Lake uranium-thorium-rare earth deposits (also known as the Blind River deposits) were discovered. This conjugation of events led to uranium production in the Elliot Lake camp, quickly followed by the co-production of thorium and, later, the rare earths. Uranium production in the Elliot Lake camp continued from 1955 to 1996. Thorium was produced continuously from 1959 to 1969. Rare earths were produced, intermittently, from 1965 to 1990. Complete production records are not readily available for thorium and the rare earths but unquestionably Elliot Lake production made a significant contribution to world production. This paper is intended to present as much of the information that is available."

Jan 1, 2012

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

By N. Coli

The exhausted Santa Barbara open pit mine (Tuscany, Italy), owned by the main electric power company in Italy (ENEL S.p.A,) extracted lignite as a fuel for the Santa Barbara thermoelectric power plant. The mining activity led to the excavation of a wide slope (with maximum height of 200 m and a planar extension of about 1300 m x 500 m) in the Shale Limestone Chaotic Complex (SLCC) (Figure 1). Since the beginning of its excavation the slope underwent rotational landslides and diffuse instability phenomena. From a geotechnical point of view the SLCC represents a typical bimrock (block-in-matrix rock) (Medley 1994, Medley 2002, Medley 2007) characterized by a mixture of a highly sheared, scaly-fabric, clayey matrix and calcareous blocks ranging from a few millimetres to tens of metres in size. Since the geometrical properties of blocks (grain-size distribution, shape, orientation and volumetric proportion) have been proved to influence the mechanical behaviour of bimrocks (Lindquist & Goodman 1994, Goodman & Ahlgren 2000, Kim et al. 2004, Sonmez et al. 2006), the aim of the present study is to investigate the geometrical properties of calcareous blocks in order to properly characterize the mechanical behaviour of the SLCC bimrock and to further assess the stability of the slope. Block size-distribution and shape were investigated by means of advanced image analysis techniques of SLCC pictures taken in the field. Geostatistical semivariograms and variographic maps were also used in order to investigate the anisotropy of block spatial distribution. Finally, in-situ large sized sieving tests were carried out to investigate the volumetric block proportion within the clayey matrix.

May 1, 2009

By L. Vollert

In-situ recovery of metals is presently experiencing a revival not seen since early applications in amenable copper oxide deposits, uranium and generally applications where neither, porosity and permeability, nor process chemistry have been prohibitively difficult. With ever decreasing grades in current mining operations or Greenfields projects and ever increasing capital and operating costs, in-situ recovery is looked to as the processing option that will both unlock these deposits as well as potentially derive revenue from mineralised waste remaining in the ground once traditional mining and processing methods become uneconomical. In-situ recovery is also being looked to as a mining method that minimises the environmental impact sustained in the application of traditional energy and water intensive mining and processing operations where millions of tonnes of ore are mined from the earth, processed on surface and then disposed of in both waste dumps and tailings facilities. The key challenge facing companies like Newcrest is that these low-grade deposits or remnant mines are generally hard rock applications that require costly methods to liberate the valuable minerals. A further challenge includes identifying suitable chemistries that both facilitate the economic recovery of gold and copper and that may be considered environmentally acceptable. This paper presents a desktop study whereby the issues of access creation and chemical extraction are discussed and evaluated with a view to driving future research in the area and unlocking this application as a real processing option. INTRODUCTION Mining companies are increasingly challenged by low grade, deep and complex ore deposits which are no longer economically exploitable by current methods. The large footprint of current open pit operations can present obstacles for permitting and social acceptance. For these reasons in-situ recovery (ISR) technologies are receiving renewed attention as a technology which could be used to exploit these more complex deposits economically and with less environmental impact. The environmental impact may be further reduced if emphasis is placed on use of renewable energy sources rather than traditional grid power, gas turbine or diesel generators are employed to drive the operation. A potential renewable energy driven ISR mine of the future is shown in Figure 1.

Jan 1, 2019

Lime-enhanced carbothermic reduction may provide an alternative process for treating low grade chalcopyrite concentrates. To date, most research on lime-enhanced reduction has been on pure, synthetic sulfides. In this study, preliminary experiments were carried out on natural chalcopyrite using a thermal analysis system to assess the rate and extent of reaction at several temperatures and identify the major solid and gaseous reaction products. Calculations were performed to establish the thermodynamic limits of the reactions in the temperature range of interest in order to identify the potential conditions for processing chalcopyrite concentrate. The study found that finely ground chalcopyrite can be reduced carbothermically in the presence of lime at moderate temperatures and in a reasonable time to form metallic copper, with the sulphur reporting virtually entirely to calcium sulfide. At temperatures below about 750?770ºC calcium ferrite is the stable form of iron whereas at higher temperatures metallic iron is stable. Further work is required to demonstrate the reaction on a scale to obtain sufficient sample for evaluation of subsequent processing steps to remove the gangue material and iron products from the copper.

Jan 1, 2009

By Chikaosa Tanimoto

INTRODUCTION Bratislava is located at the intersection of important traffic routes, including motor-ways, roads, railways, air traffic, trading, and inland waterway with an important harbour. The construction of the D2 Motorway Bratislava, Lamacska cesta Stare grunty was the last missing section of D2 Motorway and its completion linked the Czech Republic through Bratislava to the Hungarian Republic. Traffic was obliged until its completion to use the Lamacska Road and Mlynska Dolina, which were the most heavily trafficked roads in the city. The section of D2 Motorway to be completed in 2006 was 3,300m in length, of which the SITINA Tunnel was approximately half the length. After putting into operation the transit traffic(motorway) and urban traffic was separated. Transit traffic by passing the town was eased. The junctions D2 with Lamacska Road (Harmincova) and Mlynska Dolina also allowed better use of the motorway for the urban traffic The tunnel construction was specified by the features with the highly weathered and thermally altered granitic rock formation with the overburden of Quaternary sediment of 2?4 m thick, very thin overburden, severely controlled deformation limit and environmental protection. The tunnel had to be excavated beneath and nearby the academic complex area and the zoo, where sensitive facilities exist and animals live in. The tunnel consisted of two tunnels (Tunnel A and B) with the length of 1,415 and 1,440 m, respectively. The overburden thickness was in the range from 10?30 m. The standard cross-section and the one with invert arch were 79.5?81.5 m2 and 92.1?93.3 m2. The excavation took 21 months from September 2003 to May 2005. The construction was based on the concept of NATM. The SITINA Tunnel was the third application of NATM in Slovakia, following the BRANKISKO Tunnel (commenced in July 2003) as the first and the HORELICA Tunnel (in October 2004) as the second NATM practice. To protect the surrounding structures and citizens from tunneling operations, seismic monitoring was performed in association with blasting. The allowable limit of blasting vibration was fixed to be under the particle velocity of 15 mm/sec. The tunnel excavation cleared this limit as expected before construction. In driving through the difficult geological situation the excavation work hit 49 faults, and some of them occasionally caused serious face instability. In principle, the rock formation has been affected by the high hydrothermal effect and the resultant clay filing along faults and joints. The auxiliary reinforcement with the 4?8 m long pipe roofing was needed to protect the vicinity of mining face area. This operation extraordinarily required additional works and time which had not been expected before construction.

The El Pe±on gold-silver deposit comprises four epithermal, low-sulfidation veins, which contain 2.9 million oz Au and 48 million oz Ag. Provisional data on alteration mineralogy, fluid inclusions, and vein textures constrain the chemistry and hydrology of the hydrothermal system responsible for ore mineralisation at El Pe±on. Alteration minerals include quartz, adularia, albite, illite, smectite, calcite, chlorite, and pyrite. Alteration minerals suggest the existence of near neutral pH, low salinity hydrothermal fluids, which circulated over an area greater than 18 km2. Complex mineral zonation patterns result from variations in host rock permeability and composition, overprinting alteration possibly produced by thermal waters from surficial and peripheral parts of the hydrothermal system, and supergene weathering in the hyperarid environment. Upflow zones were focused along N-S and NE trending structures, producing crustiform quartz-adularia+carbonate veins. Fluid inclusion data indicate vein deposition from low salinity (

Jan 1, 2002

By Anu Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Miner Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the NIOSH Bruceton Experimental Mine was pressurized using a 1.1 m (42 in) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

Alkaline leaching with sodium carbonate solution adjusted to pH 9·5 to 10·0 preferentially dissolves thorium from a mixture of rare earth and thorium hydroxides. Rare earth sodium carbonates form in the alkaline leaching stage.These are converted to rare earth oxides for use as optical and ophthalmic polishing agents. Quadrivalent cerium is extracted under similar alkaline leaching conditions.INTRODUCTIONAustralia has made significant contributions to mineral chemistry and mineral dressing. As often happens with an industrially immature country, research investigations often outstrip the ability or desire of commerce to exploit them. It is wrong to think exclusively in terms of export of raw materials. Imagination assists in developing world trends. The chemical utilization of mineral sands has interested a group of investigators, chiefly at the Commonwealth Scientific and Industrial Research Organization (C.S.I.R.O.) and, more recently, in the mining industry itself. From an international point of view the highlight of this work was Newnham's (1960) process for the separation of hafnium from zirconium. Earlier work at C.S.I.R.O. investigated the chlorination of rutile, zircon, and monazite. Assuming that titanium tetrachloride would be available in large quantities in the post war years, extensive work was done by Kraitzer, McTaggart, and Winter (1948) on organic compounds of titanium. This work led to the development of heat resistant paints, plastic compositions, and improved organic protective coatings that predated overseas work by up to seven years. (Post, Shiihara and Schwartz, 1961; Anon, 1955). Contributions were made to the production of refractory hard metals (Kraitzer, 1949; Kraitzer and Newnham, 1956). Pilkington and Wylie (1947) and Urie (1947) investigated the production of rare earths from monazite by an acid process.

Jan 1, 1963

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012

Residual aeolian placers (RAPs) are formed by the wind, by preferential entrainment and removal of small and low-density detritusfrom a pre-existing, typically sedimentary sequence containing heavy minerals. Heavy minerals that are resistant to chemical alteration and either soft and malleable (gold), or extremely hard (diamond, sapphire, ruby, etc), are concentrated as a residual on the wind deflation surface, typically in the interstices between larger resistant clasts. RAPs form preferentially in arid or semi arid areas, where the vegetation is sparse or absent, and where topography and surface gradients are low, but may also form on beaches and in periglacial environments. RAPs consist of a continuous or discontinuous, planar or gently undulating horizon of heavy minerals in a single-clast-thick pavement of resistant pebbles, cobbles, or boulders, which mantles the present topography or palaeo-topography. Extreme wind erosion and surface deflation may condense the full pre-existing sequence into a layer of heavy minerals only. The grade of RAPs is substantially higher than in the precursor deposit, and commonly much higher than those typically found in most other placer types. Aside from their general occurrence as a thin pavement of resistant clasts, the best indicators of residual aeolian gold placers are the presence of wind-eroded stones (ventifacts) on the pavement, and the distinctive and unique shapes of aeolian gold grains themselves. The shape of the gold grains is progressively transformed by sand blasting during placer development, from grains with thickened rims, to toroidal grains on which the rims are æsplitÆ and peened inward toward the grain centre on one or both of the grain sides, to hemispherical or sub-spherical grains that are fully encapsulated by the in-turned rims. Gold that has undergone aeolian shape transformation is difficult to entrain and transport away from the site of aeolian concentration by anything other than mass movement or glacial processes. It is also easily retained by commercial recovery plants of any configuration.

Jan 1, 2004

By Aquiles Vivar

Ante los problemas de sismicidad inducidos por el sistema de minado en la Compañía minera Milpo, se planteó una solución a través del sistema de monitoreo sísmico único, donde se da una distribución espacial de 20 censores entre uniaxiales y triaxiales distribuidos en 3 niveles de producción en el área de influencia de las actuales operaciones para así ubicar, cualificar y cuantificar el fenómeno a efectos de realizar los análisis interpretativos del caso. En ese sentido, el presente texto describe el sistema de monitoreo, cuyo software sísmico está diseñado para determinar nuevas estructuras formadas a partir de los eventos sísmicos pre existentes reactivadas por la sismicidad inducida, así como el desarrollo de planos de isocontornos que permiten la diferenciación entre zonas de altos y bajos esfuerzos.

Sep 9, 2007

By Tim Peterson

Factors Controlling Stability Stability of slopes in soft rock, waste dumps or soils is governed by three factors: ?Slope configuration ?Groundwater ?Shear strength

Jan 1, 2004

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Jan 1, 2007

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006

By Wylie A. W, Mathew P. J, Eisler P. L

Field studies of the radiations backscattered by iron ores from a 60Co source of primary gamma radiation located in a borehole logging probe have confirmed thatthe P" factor, a ratio of high energy gamma ray intensities to low energy intensities in selected energy windows of the backscattered gamma-ray spectrum, is a valuable measure of grade for sedimentary iron ores of the Pilbararegion of Western Australia.Laboratory studies of model boreholes have shown that variations in borehole diameter and variations in bulk density of the formations have a significant influence on the measurement of P" ratios. If these influences 'are taken into account the mean ore grade in a new blast hole, for instance, can be predicted with a probe of suitable configuration to within 0·8 per cent Fe at the 95 per cent confidence level, while the grade of a single 120-cm split can be determined to within 2·6 per cent Fe. These results were obtained by pooling data from five blast holes covering the range of iron concentrations 20-68 per cent Fe and apply to the mean hole grades 54-68 per cent Fe.Results for two development holes were generally comparable to those obtained from individual blast holes95 per cent confidence limits of ±0·9 per cent Fe for mean ore grade and ± 4·1 per cent Fe for single splits. A greater number of data points is needed before these confidence limits can be further improved.The technique utilized to obtain these results was derived from a "multiband" approach to collection of backscattered spectral intensity data, an approach which permitted selection at the data processing stage of the most statistically significant P" ratios for the type of mineralization encountered in the field. The multiband technique also permitted selection of the most significant of another set of windows in the backscattered gammarayspectrum to measure a newly developed "S-factor", a ratio sensitive to borehole diameter. Another window provided information on bulk density. All these measurements were made with a single pass of the same loggingprobe.

Jan 1, 1977