Search Documents

By Martin T

High methane content of the medium volatile metallurgical coal mined from the Coal Basin mines causes very difficult mining conditions. Rapid desorption into the mine ventilation system limits coal production, requires huge fresh air quantities and creates mine safety problems. In workings deeper than 2000 ft (600m) gassy coal and heavy cover create outbursting conditions. Cross-measure methane drainage has reduced ventilation requirements on advancing faces, but degasifica- tion of virgin coal is needed to improve mining Conditions.

Jan 1, 1982

By Chick Kerkering, Stephen Iverson

Perimeter control blasting is common in civil construction projects but not as common in mining. A poorly designed and executed underground mine development blast design can result in unwanted wall rock damage. This damage increases the risk of rock falls and injury. With the availability of good drilling equipment, it is a simple matter to add the few extra holes needed to change conventional drifting into drifting with perimeter control.

Jan 1, 2008

By Mahyera A, Sakashita B, Ahmed U, Abou-Sayed AS

Gas in U.S. coals is primarily composed of 90 to 99 percent methane and up to 10 per- cent carbon dioxide. In composition and heat- ing value, this coal-bed gas is similar to natural gas and can be introduced directly into commercial pipelines after standard condition- ing. The high permeability cleat system in the virgin coal can be exploited in order to drain the coal gas well in advance of mining. Two premining drainage methods have been extensive- ly evaluated in the U.S.; they are 1) horizon- tal boreholes collared from within the mine, and 2) vertical drilling from the surface with fracturing. Limited-size fracture treatments are advocated in order to prevent potential roof damage and the need for added support. An engineering approach to predicting gas flow for different drainage techniques near mining locations is presented. Results can be used in design, i.e. pipeline, compressor. Coal gas drainage from a horizontal borehole and a treated (contained fracture) vertical well for a 6 foot seam have been evaluated. Based on these results, it was concluded that selection of gas drainage techniques will depend primar

Jan 1, 1982

By Terry L. Muldoon

The Bureau of Mines conducted an investigation to quantify microphone response variations that could result when the microphone is worn by a worker, as with a personal noise dosimeter, and to suggest an optimum placement and orientation of the microphone for noise exposure measurements. Previous studies have shown no significant variations in a diffuse field. This investigation, therefore, was conducted in the free-field conditions of an anechoic chamber using an anthropometric dummy as a subject, and broad band noise as the acoustic stimulus. This investigation established that, in a free field, the wearer's body does significantly affect microphone response; the response variations are a function of azimuth, and location and orientation of the microphone. Results suggest that locating the microphone on top of the subject's shoulder, oriented parallel to the body axis, should yield data comparable to that obtained using a sound-level meter.

Jan 1, 1973

By Scott R. Giese, Lucas Dix

"Recently, there is a growing trend in the aluminum foundry industry to develop· improved melting and casting processes to produce lightweight, high-strength, and thin-wall castings for the aerospace and transportation industry. One casting method that has demonstrated industrial potential for producing clean, thinwall castings is vacuum-assisted, counter gravity casting. This process has the benefit of expeditiously and quiescently filling the casting cavity with a dramatic reduction of furnace related and reoxidation inclusions. Additionally, lower casting temperatures can be utilized because the application of vacuum during filling overcomes the resistive internal cavity pressure resulting in a finer, as-cast microstructure. The paper explores and discusses the processing and design conditions in improving the mechanical properties of A206 casting alloy using the vacuum assisted, counter gravity casting process.IntroductionThe process of metal casting has been, over the centuries, the chief production technique for components used in everyday life. However, the casting process has certain inherent problems that can adversely effect the properties of a finished product. These problems are directly attributable to the gravity pouring technique used to transfer molten metal to the mold and to fill the mold cavity.A recent study for the American Metalcasting Consortium demonstrated reoxidation products created during the casting process are five times more likely to cause product rejects than entrapped molding aggregates, melt slag, or furnace lining materials1. Formation of nonmetallic and intennetallic compounds are more prevalent in aluminum and titanium alloys because of their reactiveness to furnace lining materials and their high affinity for oxygen. The incorporation of undesirable compounds can be attributed to four areas of the casting operation. The sources are charge materials, melting technique, pouring methodology, and casting cavity filling. Aluminum foundry men have addressed the first three areas by selecting high quality melt stock, non-stirring melting equipment, and the use of porous ceramic filters. Unfortunately, little consideration is given to the last, but yet tl.1e most important part of the casting operation, the actual fill mg of the casting cavity.The generation of inclusion defects during the casting process can be described by two methods. As the liquid metal flows in the gating network and casting cavity, abrupt changes in flow d1rect10n cause the metal to become agitated. This mechanism liquid metal splashing, is generated by instability of the advancing liquid metal interface from turbulence effects as schematically illustrated in figure 1a2 . The surface oxide film bursts under high velocity conditions, folds over, and becomes dispersed and incorporated in the bulk liquid. Additionally, fragmented liquid droplets ejected from the disturbed interface oxidize and become dispersed in the metal stream."

Jan 1, 2000

By Ronald Althouse

During the past five years under contract with the U. S. Bureau of Mines (BOM Contract J0308002). West Virginia University's Mining Extension Service (WVU-MES) has designed, developed) and delivered to the mining industry a comprehensive training program for Mine Rescue (MR) teams and a management planning tool for Mine Emergency Preparedness. The Mine Rescue team program is systematically built on a set of training objectives, backed up by content, allowing mine operators to conduct team training activities. These materials are user-ready, provide the MR principles and practices for both initial and advanced training, and supply teams with exercises geared to problem-solving activities. In addition to an instructor's program guide, the eight (8) modules that comprise the initial (20 hour) MR training are: an Introduction to Mine Rescue, an Introduction to Self-Contained Breathing Apparatus (SCBA), a set of modules covering each approved minimum 2-hour SCBA (i.e.) the Draeger BO 174-A. the McCaa) the Aerolox. & the Scott Rescue-Pak), and a manual on Auxiliary Apparatus as well as the Chemox Auxiliary SCBA. Advanced, annual refresher training (40 hour) is covered by seven (7) modules that spell-out the principles and practices needed to establish surface organization, to handle mine gases as well as mine ventilation, to conduct exploration, for fires, firefighting, and explosions, to rescue survivors and recover bodies, and to accomplish a mine recovery. Approved by MSHA in 1984 to meet requirements for 30 CFO. Part 49, these materials provide a basis for trainers' instruction, for comparison of team capabilities, for modifying programs resources, and services, and for program planning. The Mine Emergency Preparedness Program (MEPP) is used by management as a tool in the preparation of company personnel for handling a mine emergency operation. As a wholly new program. MEPP depends upon development of a Mine Emergency Organization and Emergency Operations Procedures. It also requires regular scheduling of drills) periodic mock emergencies, and evaluation of organizational responses and program performance beyond required training of mine rescue teams. MEPP materials are arranged into three sets of guides: 1) the Preparedness Program System Guides include an Executive Summary, a Program Director's Guide Mine Emergency Organization, and Emergency Operations Procedures; 2) the Emergency Organization (MEO) User's Guides cover the Rescue and Advisory Division, the Technical/Safeguarding Division, and the Surface Support Division; and 3) the Emergency Procedures (EOPS) User's Guides detail Containment Level Procedures, Notification Level Procedures. Mobilization Level Procedures, and Deployment Level Procedures.

Jan 1, 1986

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Janusz S. Laskowski

The flotation-related properties of hexanol derivatives and mono-alkyl ethers of propylene oxide, which include many important flotation frothers (e.g. MIBC, DF-200, DF-250, DF-1012, etc.) have been studied. The obtained results show that the DFI (Dynamic Foamability Index) - CCC (Critical Coalescence Concentration) plot can be used to classify flotation frothers. The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers.

Jan 1, 2003

By M. Clair Smith

The Bureau of Mines investigated the Rip Van Winkle mine, which is about 25 miles northwest of Elko, Nev., from October 1942 to February 1943 to determine possible resources of lead-zinc-silver ore. The property is owned by the Rip Van Winkle Consolidated Mining Co., which maintains its offices in Salt Lake City, Utah. Ore was discovered in the 1860's, and active mining was carried out intermittently until 1939, when the Rip Van Winkle Consolidate Mining Co. acquired the property. This company equipped and developed the mine, erected a flotation mill, and operated on a 65-ton daily basis. The ore is mined from veins, mineralized faults, and replacement deposits of wall rock. The country rock comprises cherty shale, granite, porphyry, intrusive breccia, and breccia, and brecciated shale. Mining operations were carried down to the 700-foot level. The Bureau of Mines drilled 5 diamond-drill holes, totaling 1,084 feet, from the 600- and 700-foot levels, excavated a 250-foot surface trench, and took 26 underground samples. The ensuing sections note the location and physical features of the district, mention the equipment, and specify the property and ownership. The history of the mine is briefed, and the geology, mine workings, and plant are described. The work performed by the Bureau of Mines is summarized and supplemented in detail by assay maps, logs of diamond-drill holes in appendix A, and by tables of sample analysis in appendix B.

Jan 1, 1949

By Charles Goodeve

"BEFORE I begin, I should like to thank The Canadian Institute of Mining and Metallurgy for the honour they have bestowed in inviting me to give this address at the fourth annual C.I.M. Conference of Metallurgists banquet.Secondly, I should like' to convey the greetings of the Iron and Steel Institute of Great Britain in accordance with a request made by its Council at its last meeting. The I.S.I. hopes for the continued growth in strength of this annual Conference and in the collaboration between our respective societies.When I read the program of this Conference, it was brought home to me what a non-ferrons country Canada is. Also, I realized what enormous advances have been, and are being made, and what an ex-citing field non-ferrous metallurgy is for the scientist. This made me wonder, as I have done before, whether the future for steel was proof against these advances.At present, iron and steel stand astride the metallurgical world like a Colossus; I hope that the bronze industry will pardon my stealing their thunder and mixing my metaphors! Will this still be so in the future?The best way to answer this question is to take a look at the fundamentals to see why the iron atom dominates to such an extent that al! other metals are called ""non-ferrons."" Is its present position due to historical and therefore ephemeral reasons, or is there a fundamental difference between the atom of iron and those of other metals?"

Jan 1, 1966

By Carlos Henrique Silveira Aguiar

O tubo formador de espiras é uma guia que está localizada no Laying Head, especificado de acordo com a norma ASTM 335P22, e tem por função conformar o fio-máquina na forma de espiras sobre o transportador Stelmor. O Laying Head gira continuamente, durante a operação normal, sendo que a cada revolução do tubo, uma espira é produzida, cujo diâmetro é determinado pelo raio final do tubo e pela velocidade do Laying Head, em relação à velocidade do Laminador. Estes tubos, durante a laminação dos aços BEXX, sofrem um desgaste acentuado, que é provocado pela carepa formada durante a passagem do fio máquina pelas caixas d’água, durante o processo de resfriamento. Desta forma, torna-se necessário trocá-los a cada 200t laminadas do referido aço, com tempo estimado de 30 minutos de parada. Além disso, há um desgaste físico acentuado na atividade de troca dos tubos, que coloca em risco a segurança dos funcionários. Outro efeito indesejável relaciona-se com o risco de ocorrência de sucata de linha, provocada pelo rasgamento do tubo, quando são fornecidos tubos cuja composição química se apresenta no limite inferior de especificação. Há programa de laminação que exige até 6 trocas diárias de tubo. Com a proposta de se incrementar a tonelagem laminada por canal dos discos de laminação do Bloco No Twist, tornou-se necessário desenvolver um tubo com insertos de metal duro, com vistas a aumentar a vida útil dos mesmos, como também a produtividade do Laminador 2.

Jul 30, 2018

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By N. Voennann

Stillwater Mining Company operates an electric furnace at its smelter in Columbus, Montana to treat a Ni-Cu-platinum group metal concentrate along with secondary PGM bearing materials. Hatch Associates has designed several improvements to this furnace, which was originally built by others. Implementation of these relatively low cost improvements has resulted in substantial increases in furnace availability and capacity, along with reduced unit costs. ? The improvements included: ? Installation of water-cooled copper cooling elements to stabilize refractory wear and increase furnace life.- ? Improved furnace 'bindings, to enhance the furnace's structural integrity by improving the contact between the refractory and cooling elements, and by promoting tight brick joints resistant to matte or slag leaks. ? Adjustment of the electrode regulator to allow higher furnace power levels. ? Installation of an automated air-slide (aeration conveyor) feed system to evenly distribute the furnace feed in an insulating layer on the bath surface. This "black-top" practice reduces unit energy costs and makes available additional smelting capacity.- ? Electrode seals to reduce ingress of air that absorbs heat before exiting the furnace in the off-gas stream. The saved energy can be used to smelt additional concentrate. This paper describes the above furnace modifications, and the benefits derived from their implementation.

Jan 1, 1998

By R. Bruce Tippin

because of the mineral's high monetary value and the spotty occurrence of free gold in the deposit. Setting up a plant sampling procedure by simply applying the usual statistical sampling theory was questionable. Two sampling concepts were considered in the sampling study: o a sufficient number of assays can be taken such that the average determined from these individual samples represents a known quantity of ore. o a sufficient weight of sample can be taken such that when assayed it represents a known quantity of ore. The test program included evaluation of sampling techniques, sample preparation and analytical methods. The overall sampling program is depicted in Figure 2.

Jan 1, 1985

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By Jean Igor Margem

Nestes dias materiais ecológicos como compósitos com fibras naturais em matriz polimérica estão chamando a atenção de pesquisadores científicos, devido ao seu bom desempenho na substituição de materiais como madeira, polímeros à base de petróleo e outros. Neste trabalho foram avaliadas as propriedades de tração de compósitos de matriz poliéster reforçados com diferentes espécimes de fibras lignocelulósicas. Compósitos reforçados com até 30% em volume de fibras longas, contínuas e alinhadas de malva, sisal e bambu foram testados em uma máquina Instron a temperatura ambiente. A fratura foi analisada por SEM. Os resultados mostraram alterações significativas nas propriedades mecânicas com a quantidade dessas fibras. Estas propriedades mecânicas foram comparados com outros resultados em compósitos testados em ensaio de tração. Como esperado, a análise da fratura revelou uma fraca interação da interface fibra / matriz, o que corrobora o comportamento típico das fibras naturais quando incorporadas em matriz polimérica.

Oct 30, 2017

By Marshall K. I

THE problem of satisfactorily eliminating the fumes and dust which are unavoidably produced in various metallurgical and manufacturing industries is one which has received considerable attention in the past, and has been the subject of much investigation and research. The solution of this problem was urgently desired for two reasons, the principal one being the fact that a considerable percentage of the total process losses in many industries was represented by the commercial values of the fumes and dust that escaped from the stack.The other reason is that, in some instances, the emission of the matter is regarded as objectionable. Various methods have been designed with a view to solving the problem thus presented, and the latest development that has beendesigned is the process of electrostatic precipitation. Continued investigational and developmental work with this process has already demonstrated its applicability to many industries, and new uses to which the process can be put are being opened up. Its use is already widespread, and the economic success that has attended its application in most instances would indicate that its use will become more general in the future.It has proved its ability to treat gases over wide ranges of temperature, and has successfully handled various types of fumes whose chemical characteristics differ very considerably. In many processes it has now come to be regarded as standard equipment.HISTORY OF ELECTRICAL PRECIPITATIONThe first recorded observations on the influence of an electrified insulated wire on gases containing solid particles in suspension was made as early as 1824 by Hohlfeld, in Leipzig. He found that, if he electrified a wire hung in a bottle filled with smoke, the smoke cleared rapidly, and a deposit formed on the sides and bottom of the bottle.

Jan 1, 1923

By S. J. Cook

The subject of capital and the Canadian mining industry is so broad as to be impossible of comprehensive treatment in brief form. The purpose of the present paper therefore will be only to outline in a meagre and somewhat sketchy way the nature and extent of the mineral industry in Canada and to point out those features which are likely to be of general public interest. Canada's mineral industry has a long and creditable production record. The? value of the output per capita rose from $2.23 in 1886 to a maximum of $26.40 in 1920 and the value of the products from ten million dollars in the former year to almost two hundred and twenty-eight million dollars in 1920. Compared with other primary industries and on the basis of the value of production, mining held third place in Canada in 1920, the premier position going to agriculture and the value of forestry production placing that industry second in the list. In the mineral industry, between six and seven thousand properties are operated annually giving employment to up- wards of sixty thousand employees to whom about seventy-five million dollars is paid in salaries and wages. During 1923, seventeen mineral products reached a production value of one million dollars or over in Canada and in order of the values assigned these were: coal, gold, nickel, cement, cop-per, silver, clay products, lead, asbestos, natural gas, stone, zinc, lime, cobalt, sand and gravel, gypsum and salt.

Jan 1, 1924

By E. A. Roux

As the first mine-to-metal zinc operation utilising atmospheric leaching, solvent extraction and electrowinning, Skorpion Zinc faces unique challenges and opportunities. One of these challenges is found in the solvent extraction circuit, in which di-ethylhexyl phosphoric acid (D2EHPA) is used as the organic extractant. Although D2EHPA is an excellent extractant for zinc, it suffers from the co-extraction of ferric iron, which is produced during leaching and by the corrosion of the grinding media. This situation is partially mitigated by iron precipitation in the neutralisation step prior to solvent extraction. Unfortunately, some ferric iron still reports to the solvent extraction process. This leads to a slow build up of iron in the organic phase. Chemical stripping is used to maintain the Fe concentration at an acceptable level. In this paper, the efficiency of the iron removal process is discussed.

Jan 1, 2006

By C. Graham

Thin Spray-On Liners (TSLs) have been researched and in development for over two decades and yet their fully functional and widely justifiable application in mining has yet to be achieved. While the explanation for this is partly technical, it is also clear that proving and communicating the operational and economic case for why a mine should change from mesh or shotcrete liners to a TSL is not a trivial matter. Evidence must be presented and communicated effectively, that is both obvious and compelling for a mine operator. The paper describes recent work carried out and directed towards this end, with funding from CAMIRO?s Deep Mining Research Consortium and additional support from 3M Canada and ABB Canada. The essential progress that has been, or is in the process of being made, will be described in providing the necessary proof of acceptable or superior TSL performance in the following areas: polymer formulation, health and safety, geotechnical specification, robotic liner application, business case economics and yielding ground support effectiveness. Future plans are also presented to demonstrate the performance of a new 3M composite TSL/yielding bolt support system in underground trials where the substrate rock is intended to fail through a number of mining-induced mechanisms.

Aug 1, 2013