Search Documents

By Robert Hopler

THE work that is being done by the Government to reduce the dangers of mining was brought out strikingly in the First National Mine-Safety Demonstration which occurred at Pittsburgh, Pa., on October 30th and 31st, under the auspices of the United States Bureau of Mines with the assistance of the American National Red Cross Society and the Pittsburgh Coal Operators’ Association.

Jan 1, 2012

By Jadson Barbosa

Corpos de prova de ferro com diferentes níveis de pureza – um de pureza ultraelevada, dois de pureza elevada e um puro comercial – foram testados mecanicamente com diferentes taxas de deformação no âmbito de um antigo projeto. O objetivo era obter a resistência à tração de cada material e verificar a influência das impurezas e da taxa de deformação nas propriedades mecânicas do ferro de pureza ultraelevada. Para melhor compreender os resultados desses ensaios de tração, uma caracterização microscópica detalhada dessas amostras é realizada através deste trabalho. Para tal, foram analisadas as superfícies lateral e de fratura dos corpos de prova de tração no estereomicroscópio e no Microscópio Eletrônico de Varredura (MEV). O dano foi analisado em seções longitudinais ao longo do eixo de tração utilizando o microscópio óptico; a estrutura dos grãos deformados foi investigada por meio da técnica de microscopia EBSD (Difração de elétrons retroespalhados). Microestrutura, padrão de deformação, orientação dos grãos e as características das superfícies lateral e de fratura são então comparadas quanto ao processo de fabricação, nível de pureza e taxa de deformação.

Aug 17, 2017

By L. Zhou, A. Martikainen, G. Goodman

Continuous airflow monitoring can improve the safety of the underground work force by ensuring the uninterrupted and controlled distribution of mine ventilation to all working areas. Air velocity measurements vary significantly and can change rapidly depending on the exact measurement location and, in particular, due to the presence of obstructions in the air stream. Air velocity must be measured at locations away from obstructions to avoid the vortices and eddies that can produce inaccurate readings. Further, an uninterrupted measurement path cannot always be guaranteed when using continuous airflow monitors due to the presence of nearby equipment, personnel, roof falls and rib rolls. Effective use of these devices requires selection of a minimum distance from an obstacle, such that an air velocity measurement can be made but not affected by the presence of that obstacle. This paper investigates the impacts of an obstruction on the behavior of downstream airflow using a numerical CFD model calibrated with experimental test results from underground testing. Factors including entry size, obstruction size and the inlet or incident velocity are examined for their effects on the distributions of airflow around an obstruction. A relationship is developed between the minimum measurement distance and the hydraulic diameters of the entry and the obstruction. A final analysis considers the impacts of continuous monitor location on the accuracy of velocity measurements and on the application of minimum measurement distance guidelines.

Jan 1, 2012

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined.1 Conductivity hard was 98.26 per cent. After a 10-min. heating at 200° C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. MATERIAL AND METHOD The work was done on high grade electrolytic copper, 99.942 per cent. copper-plus silver, silver 0.0008 per cent. It was hot-rolled to 3 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

[Secretary's Note.—The following official tables, prepared by the government of the State of Nuevo Leon, and presented to the Institute at the fifth seseion of its Mexican meeting, held at Monterrey, November 26, 1901, present in compact form a general summary of the mineral and metallurgical industry of the State for the preceding calendar year, together with a statement of the railway-shipments of ores from January 1 to October 31, 1901, which, in the absence of direct official mining and metallurgical statistics (not yet available for that year), clearly indicates an increased activity and productiveness of these industries. In other words, the mines are reported to have yielded in 1900 a total product of 83,960,169 kilos of ore; whereas, the railway is reported to have carried, in 10 months of 1901, a total of 108,318,647 kilos of ore. At this rate, the railway-shipments for 1901 mould amount to nearly 130,000,000 kilos. It is, of course, possible that the railwaystatistics include other freight than ores, or that they include duplications, such as would be involved in the record, first of certain ores transported, and afterwards of the " base bullion " produced therefrom. An accurate comparison is therefore impossible ; yet, after making all reasonable allowances for such items as have been named, it seems safe to infer that the mining and metallurgical industry of this State accomplished in 1901 a substantial progress.]

Jan 1, 1902

By Edward L. Wilson, Keshavan Nair, Ranbir S. Sandhu

In planning and designing of underground excavations and construction, it is of considerable importance that the stresses and displacements in the rock mass subjected to arbitrary sequences of unloading and loading be within allowable limits. For determination of the stress and displacement fields, the usual approach is to treat the rock as an elastic material and to apply the principles of the theory of elasticity. However, analytic solutions are available only for a limited class of problems of simple geometry and idealized material properties. Nonhomogeneity and anisotropy of material coupled with complex geometrical configuration and initial stress fields that are almost always preexistent in rock masses at great depths, render the problem intractable by analytical methods. Approximate solution techniques using numerical procedures have, therefore, to be resorted to. The finite element method as applied to plane stress analysis was introduced by Clough.1 It has developed into a powerful tool for the analysis of various field problems in structural and continuum mechanics. The method is well documented in the literature2-6 and, therefore, its historical development will not be discussed here. Wilson's analysis of the plane stress/strain problem has found extensive use in the area of soil and rock mechanics including stresses around underground openings; stresses and displacements in dams, foundations, etc.7-11 In his analysis of the axisymmetric solid,3 Wilson proposed a procedure to allow for certain cases of nonlinear material properties. In this chapter, the develop-

Jan 1, 1972

By Noan Tonini SImonassi

Fibras de rami (Boehmeria nivea) estão entre as lignocelulósicas naturais com potencial para utilização em compósitos poliméricos. O presente trabalho avalia a resistência ao impacto deste tipo de compósito. Corpos de prova normalizados foram confeccionados com percentuais de até 30% em volume de tecido de rami alinhadas ao longo de todo o comprimento. As fibras foram embutidas sob pressão em matriz de resina poliéster do tipo ortoftálica curada à temperatura ambiente por 24 horas. Os corpos de prova foram ensaiados em pêndulo de impacto Izod e as superfícies de fratura analisadas por microscopia eletrônica de varredura, MEV. A resistência ao impacto aumentou exponencialmente com a quantidade relativa de tecido de rami reforçando o compósito. Este desempenho foi associado à dificuldade de ruptura imposta pelas fibras bem como ao tipo de trincas resultantes da interação tecido de rami/matriz de poliéster que ajuda a absorver a energia do impacto.

Aug 17, 2017

By A. Tsubouchi, F. Noguchi, T. Takasu

"A high current density operation is desired to improve the productivity in copper electrorefining. However, a lot of problems still remain such as passivation at anode, dendritic deposition at cathode and impurity behavior during the electro refining.Effects of the current densitY on the morphology of copper deposition on the cathode, and passivation at the anode were investigated at various fluid velocity of electrolyte in the present study.Although a granular appearance of the copper deposition was obtained with increasing high current density, it was depressed by an increase of the fluid velocity of the electrolyte. A uniform deposition on the cathode was also observed when the fluid velocity of the electrolyte become higher. It was ascertained that passivation at the anode was suppressed by circulating electrolyte during electrolysis. INTRODUCTIONIt is desirable to operate at high current density in copper electrorefining in order to improve plant productivity without enlarging the size of electrodes(1). However, there are many problems in copper electrorefining at high current density with the usual commercial practice, for example, anode passivation, dendritic deposition and an increase of impurities in the cathode.In general, it is effective to agitate the electrolyte in order to suppress these problems(2). Smith et a1.(3) have performed electro refining experiments at various current densities in the range of 8 to 32 Aldm2 and at electrolyte fluid velocities in the range of 40 to 120 mlmin, and they obtained well consolidated, void free copper even at high current density in a high electrolyte velocity. However, they did not discuss the recovery ratio and the passivation behaviour at the anode. Walsh et a1.(4)(5)(6) experimented with the rotating cylinder electrode, and ascertained that electrolysis can be carried out at high current densities under the condition of pure electrolyte.With regards to anode passivation, there are several papers by previous workers(7)(8). Our group ascertained the process of producing anode slime during electrolysis(9). However, these experiments were carried out without forced circulation of electrolyte. Therefore, in the present study, to solve these problems, we electrolyzed at current densities in the range of 4 to 50 Aldm2 with circulating electrolyte in the range of 0 to 48 mlrnin. The effect of electrolyte fluid velocity on the surface morphology of deposited copper at cathode and passivation at anode were investigated when electrolysis were carried out with circulating electrolyte at high fluid velocity and at high current density."

Jan 1, 1997

By Peter K. Strangway

During 1973, a 20,000 net ton (18 100 metric ton) formcoke test was carried out at Inland's 26.5-foot (8.08-meter) hearth diameter on NO. 5 Blast Furnace. The formcoke briquettes were produced from Elko1 coal by FMC at their pilot plant in Kemmerer, Wyoming. The briquettes were shipped to Inland in open railroad cars and most of them were placed in an outside storage field until a sufficient amount was available for the actual blast furnace test. The test consisted of three phases: an initial four-week base period; the actual 33-day formcoke test period; and a final three-week post-test base period. During the formcoke test period, the regular coke skip loads were gradually replaced with skips of formcoke until, after a three-week period, the replacement ratio reached 80%. The furnace operated smoothly and quality hot metal was produced. The burden remained permeable and it was possible to maintain wind rates 9 of over 100,000 scfm (47 Nm3/s) without significant blast pressure increases. Dusting from the formcoke was not a problem either in the stockhouse or in the top gas. The formcoke briquettes maintained their original shape and density as they descended through the furnace. When the 80 percent replacement level had been reached, the inwall temperatures became higher than normal (about 2000 ºF (1090 ºC)) and followed an unusual steady pattern. In addition, the top gas temperature became higher than normal, and the hot metal analyses and temperatures began to fluctuate unacceptably. In general, it is felt that the high inwall temperatures were a result of channeling of the hot furnace gases along the stack walls. This channeling appears to have been promoted by a change in distribution of the burden in the top of the furnace which, undoubtedly, was caused by the increased increments of formcoke. Since it was felt to be unsafe to operate the furnace for an extended period of time with the inwall temperatures at the high level, a decision was made to remove the formcoke from the furnace. When this was done, the inwall temperatures returned to normal. Once the inwall temperatures had returned to normal, the remaining 3,800 net tons (3450 metric tons) of formcoke were used in the furnace at a nominal 40% replacement level for five continuous days. The furnace operated smoothly during this period, and the results were representative of satisfactory furnace operation with partial replacement of regular coke with formcoke. The test was successful in proving that formcoke can replace up to about 50% of the regular coke in a large furnace operating at high wind rates. However, additional work will be required to develop acceptable charging practices for using higher levels of formcoke replacement.

Jan 1, 1977

By Renato Drescher Subtil

A tecnologia de cominuição de minérios através de Prensas de Rolos de Alta Pressão vem se destacando nos diversos segmentos da mineração, o que faz com que as usinas de pelotização de minério venham introduzindo Prensas de Rolos em seu processo produtivo. Apesar dos benefícios dessa mudança, observa-se pouco conhecimento da influência das variáveis intervenientes ao processo de prensagem e sua relação com o Ganho de Superfície Específica. Essa compreensão é fundamental para a maximização do desempenho de prensagem. Esse artigo utiliza Redes Neurais Artificiais (RNA) para predição dos resultados no Ganho de Superfície Específica e quantifica a relevância de cada variável no processo de prensagem. Os valores preditos gerados pela RNA obtiveram ótima aproximação com os dados reais, o que indica que utilização de RNA possibilita a intervenção proativa no processo produtivo podendo resultar em uma melhoria de desempenho da prensa.

Aug 17, 2017

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By Rodrigo Vitorino da Silva

Ligas a base de zircônio utilizadas na indústria nuclear estão sujeitas à formação de hidretos que são causadores de efeito deletério no material. Para aumentar o tempo de operação desses componentes, é necessário o desenvolvimento de novas ligas que retardem ou diminuam esse efeito. Este trabalho tem como objetivo avaliar a influência da adição de elementos de liga em uma liga inédita a base de Zr-Nb na absorção de hidrogênio, através de testes que avaliam a absorção de hidrogênio e a formação de hidretos no material após processamento termomecânico e comparar seu desempenho com duas ligas comerciais. Para tal, foram realizados ensaios de microdureza, cinética de absorção de hidrogênio e micrografias. Os resultados de microdureza Vickers das três ligas estudadas, após o processamento termomecânico, são muito próximos. As curvas de cinética de absorção de hidrogênio mostram que a liga Zr-Nb-Sn-Fe apresenta melhor comportamento que as demais uma vez que o tempo para o início de absorção foi maior. As micrografias indicam que a liga proposta apresenta um desempenho superior em relação à morfologia dos hidretos visto que os mesmos são mais curtos e alinhados.

Aug 17, 2017

By K S. Smith, J Woodhead, K Olson Hoal

Mineralogy is the link between ore formation and ore extraction. It is the most fundamental component of geomet programs, and the most important aspect of a life-of-project approach to mineral resource projects. Understanding orebodies is achieved by understanding the mineralogy and texture of the materials, throughout the process, because minerals hold the information required to unlock the value they contain. Geomet mineralogy programs absolutely require the appropriate expertise and at least three steps of mineral characterisation prior to using semi-automated or other methods: field examination, thorough core logging, and optical microscopy. Economic geological inputs for orebody characterisation are necessary for orebody understanding, and are exemplified by current research in the Zambian Copperbelt, where revised sequence stratigraphy and understanding of alteration, metasomatism and metamorphism can be used to predict topical issues at mine sites. Environmental inputs for sustainability characterisation are demonstrated by recent work on tailings from the Leadville, Colorado, USA area, including linking mineralogy to water quality issues. Risk assessments need to take into account the technical uncertainties around geological variability and mineral extractability, and mineralogy is the only metric that can be used to make this risk contribution.CITATION:Olson Hoal, K, Woodhead, J and Smith, K S, 2013. The importance of mineralogical input into geometallurgy programs, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 17-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By William B. Plank

NEVER before have so many men chosen the mineral technology field for their college training. In the college year 1936-'37, 7190 such students were enrolled in the 53 schools of the United States. My last study of the mineral technology schools of the United States and Canada was made for the year -1934-'35, and the current study, as the previous one was made for the A.I.M.E. under the auspices of the Division of Mineral Industry Education. Altogether, four studies of enrollment have been made. The first three were for successive college years beginning with 1932-'33. This present one covers a two-year period, for the purpose of these studies may he served satisfactorily if they are made biannually. The data on the schools were collected in the same way as for former studies, 'namely, by questionnaire, dated in this case Nov. 18, 1936. The figures reported are therefore comparable with those of former cars.

Jan 1, 1937

By Francisco Sotillo

El artículo da cuenta de una investigación orientada a demostrar los beneficios del mecanismo de conminución en una cama de partículas, como ocurre en los rodillos de molienda de alta presión (HPGR) o molinos de rodillos de alta presión (HPRM). Se ha investigado el uso de los HPGR de laboratorio para mejorar la eficiencia de separación de los minerales con alto contenido de dolomita, ultra alto contenido de arcilla y alto contenido de arcilla (kaolinita) presentes en una mena de apatita en operaciones subsiguientes «aguas abajo» de beneficio de diferentes minerales de fosfato de origen sedimentario. La investigación incluye estudios de caracterización de minerales de fosfato dolomítico, datos del modelo físico aplicado por PerUsa EnviroMet, Inc. de HPGR para desarrollar información preliminar de conminución; y evaluaciones de HPGR de laboratorio para determinar los parámetros de chancado (velocidades de alimentación; velocidad y separación de los rodillos; torque, presión y energía aplicables).

Sep 30, 2020

This Bureau of Mines investigation addressed two primary issues of air velocity measurement in mines: the determination and use of correction factors, and the development of guidelines for the selection of a suitable site at which the measurements should be taken. Other facets of the investigation included a comparison of measurement methods and devices, and aircourse cross-sectional area measurement. The study consisted of theoretical, laboratory, and in-mine investigations. The measurement devices included in the experimental phase were vane anemometer, vortex shedding anemometer, a prototype thermoan-emometer, smoke tube, and oil of wintergreen sprayer. The measurement methods included single-point centerline, timed-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices. The study resulted in guidelines for measurement site selection that are applicable to most inmine situations. It also showed that the use of correction factors is problematic. There are many potential pit-falls and there are cogent arguments against using certain correction factors. However, generalized correction factors were developed that can be successfully applied in routine ventilation work, provided that their use is properly understood.

Jan 1, 1985

By Shazad Hosein, Bill Birch, Catherine Johnson, Toby White, Liam Bermingham

Air overpressure (AOP) from blasting can give rise to a significant number of blasting complaints from residents living adjacent to blasting operations from mines, quarries or civil engineering projects. High amplitudes of AOP are usually associated with the lateral movement of a vertical free face, but it can also be caused by the upward lifting and the venting of gases through the surface of the blast area.

Jan 1, 2018

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By Robert S. Schechter

A minitest of the new potassium chloride-potassium carbonate two-stage in-situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing cation-exchange reactions. The test also indicates permeability anisotropy and the existence of disturbed flow fields.

Jan 1, 1985