Search Documents

By Jaeheon Lee, Jae-Chun Lee, Doyun Shin, Minseuk Kim, Hyunsik Park

"The appropriate treatment of cyanide waste water is becoming an emerging issue because of the toxic residue and large quantity produced from gold processing plants. In the present article, we designed and operated a continuous biological cyanide treatment system using domestic sewage sludge and various microorganisms including a cyanide-producing and degrading bacterium, Chromobacterium violaceum. The synthetic wastewater containing 50 mg/L of cyanide was pumped continuously into the reactor at a flow rate of 500 mL/d for 21 days. When 50 mg/L of cyanide was fed, the cyanide concentration in the effluent of the reactor inoculated with activated sludge (S-50) decreased by 7.5 mg/L in the effluent. The other reactors did not show significant cyanide degradation and the reactor inoculated with C. violaceum showed increased cyanide concentration in the effluent. The microbial community in the reactors was analyzed by 16S rRNA-gene based pyrosequencing technique to investigate microbial response to cyanide addition and operation time. The microbial community analysis shows that the phylum Proteobacteria was detected in the reactors showing significant cyanide degradation (S-50), while Firmicutes and Bacteroidetes was dominant in the other reactors with very low cyanide degradation. Proteobacteria could not compete when the other phyla Firmicutes or Bacteroidetes were inoculated. This study shows the feasibility of the biological cyanide treatment system for gold processing plants and contributes new fundamental knowledge about the microbial community in the biological cyanide treatment system. INTRODUCTION Cyanidation has been widely used to recover gold from ores or secondary resources since first proposed by MacArthur and Forrest in 1888 (MacArthur et al., 1888) and it is used in many states of the USA, including Nevada, Arizona, California, Colorado, and Idaho (Laitos, 2012). Cyanide compounds are highly toxic and create serious problems for wildlife and water management (Solomonson, 1981; Donato et al., 2007). Furthermore, because many countries have imposed strict standards for cyanide discharge (USEPA, 1985), it is essential to develop a cost-effective and environmentally friendly technology for treating cyanide-containing wastewater."

Jan 1, 2018

By Gary E. Sherman

The Bureau of Mines estimated the remaining lode gold endowment of eight mining districts in Alaska using historic production data. A log-arithmic model of cumulative tonnage of ore processed versus cumulative grade was applied to the following districts: Chichagof, Fairbanks, Homer, Hope-Seward, Juneau, Ketchikan, Prince William Sound, and Willow Creek. To assess the remaining endowment, a computerized production data base was compiled from Bureau records. These data were aggregated in 5-yr intervals for each district. Data were sorted in order of declining grade, and log cumulative grade was plotted against log cumulative tonnage. Linear regression was performed on the data for each district. The linear equation for each curve was used to predict remaining endowment at a limiting mining grade. Based on conservative extrapolation of the grade-tonnage curves, a substantial total endowment of 8,415,100 tr oz of gold remains in the eight districts. The districts with the greatest remaining endowment are the Juneau, Chichagof, Fairbanks, and Willow Creek Districts.

Jan 1, 1987

By Manuel Gomez

This report presents experimental work conducted on a number of coals found within the boundaries of the Missouri River Basin, which were, to an extent, a selection of coals typical of that region. In the min, the laboratory work falls into three general classifications: (1) Laboratory distillation assay of coal to establish yields on carbonization; (2) chemical analyses of the coal samples before drying or carbonization; and (3) chemical analyses of the products of carbonization. It will be seen in the following discussion that these data derived from the small-scale laboratory apparatus are useful in predicting yields from pilot plants or industrial units. Coal is produced in about 48 general areas or mining fields in the Western States, of which approximately 18 fall within the limits of the Missouri Basin.3/ Beginning with the Northern Colorado field, through the Central and Western Wyoming fields, the coal is principally bituminous and subbituminous rank. The western Montana coals are also of these ranks. Progressing northeast from central Wyoming the coal decreases in rank, as shown by the subbituminous C coals of the Gillette field in northern Wyoming and the lignites of eastern Montana and North Dakota.

Jan 1, 1953

By Zhu Yangge, Hu Xiaoxing, Feng Qiming, Zhang Guofan, Zhang Xingrong

"During the flotation process of ilmenite and titanaugite with fatty acid as collector, unavoidable ions such as Ca2+, Mg2+, Al3+, Fe3+ and Fe2+ demonstrate considerable influence on the floatability of the minerals. In this study, flotation test, zeta potential test, and solution chemistry calculation were adopted to investigate the mechanism of how these metal ions affect the floatability of ilmenite and titanaugite in different pH conditions. The results show that in weak acidic solution, Ca2+ and Mg2+ mainly freely exist in the solution with little adsorption on mineral surface, and their reaction ability with oleate ions is weaker than active site on ilmenite surface (Fe), thus they show negligible effect on the flotation of ilmenite; Al3+ shows similar reaction ability with oleate ion compared to Fe3+, which lead to competitive reaction with collector, so the flotation of ilmenite is depressed. While Fe3+ can adsorb on surface of titanaugite in the form of Fe(OH)3, and it shows stronger reaction ability with oleate ion compared with active site on titanaugite surface (Ca and Mg), which proves an activation effect on titanaugite flotation. In alkaline solution, all these five kinds of ions can adsorb on titanaugite surface, and the floatability of titanaugite will be activation. Based on the above analysis, it can be deduced that in the flotation system using fatty acid as collector, the adsorption of metal ions on mineral surfaces and the stronger reaction ability with collector than active site on mineral surfaces, are the two prerequisites for metal ions show activation effect on mineral flotation.INTRODUCTIONIn flotation pulp, the existence of metal ions is often inevitable. There are two sources for these metal ions: the first part is generated in grinding and flotation process due to the oxidation, reduction, corrosion or dissolution of minerals or grinding medium; the second part is from the flotation water or the addition because of the technology need. The metal ions in the pulp have a considerable influence on mineral flotation. Earlier researches are focus on the activation effect of mineral floatation by metal ions to obtain a higher flotation efficiency, many effective activators were found, such as Cu2+ activated sphalerite, Pb2+ activation wolframite, and Ca2+ activation quartz flotation, these metal ions have become the commonly used activators in industrial production. And many studies attempted to explain the mechanism of how metal ions affect the floatability of minerals. James (James et al, 1972) suggests that metal hydroxide precipitation is the main component leads to activation effect, while the study of Fuerstenau (Fuerstenau, 1976) showed that the metal ion hydroxyl complexes played significant role. In recent years, the reuse of mineral processing wastewater has attracted more attention (Rao et al, 1989; Liu et al, 2013; Wang et al, 2014), as a main component in flotation wastewater, the influence of “unavoidable ions” on flotation process still need in-depth study."

Jan 1, 2018

By W. H. Bassett, C. H. Davis

The late J. P. Sparrow, chief operating engineer of the New York Edison CO., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40,70-30,80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started on Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period. Plan of Procedure In general, the procedure was to inspect the tubes at short intervals and to remove those that had begun to leak. The tubes removed were carefully examined and a photographic and microscopic record of the

Jan 1, 1925

By M. P. Roy, P. K. Singh, A. K. Mishra, Ashish K. Vishwakarma, Vivek K. Himanshu

Ground vibration is one of the major hazards produced by rock-blasting operation. The accurate prediction of vibration is necessary for designing controlled blasting parameters. The existing vibration predictors consider maximum explosive charge weight per delay and distance as the parameters responsible for ground vibration. These predictors are based on the assumption that the geometrical parameters of the blast will be constant for a site. However, the mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, the other blast design parameters will also have an impact on ground vibration intensity. A principal component analysis is a dimension reduction technique. This technique along with multivariate logarithmic regression has been used in this paper to predict the ground vibration. The technique has classified the blast design parameters into four principal components. The regression with the scores from these principal components has been carried out. The evaluation of the model performance of predictors along with the existing empirical predictors has been carried out using R2 and RMSE values. The evaluation suggests that the predictor with logarithmic regression followed by principal component analysis gives better performance with respect to the existing empirical predictors.

Jul 30, 2022

By P. A. Distin, Jr. da Silva

The history of commercial processes for zirconium/hafnium production and separation is reviewed. A new technology is then proposed as a potential alternative for zirconium/ hafnium separation in a simpler, cleaner way than achieved with current processes. Primary sources of zirconium always contain small amounts of hafnium that must be removed during production of zirconium metal for nuclear applications. This separation is usually carried out by a solvent extraction process, developed in the 1950s, that selectively extracts hafnium, as a thiocyanate complex, using methyl isobutyl ketone (MIBK). Environmental problems inherent to this process are the high aqueous solubility and low flash point of MIBK, and possible gaseous contaminants formation generated by the decomposition of the thiocyanic complexes in hydrochloric acid medium (H2S, HCN, mercaptan’s formation). The present work shows how these problems could be avoided by using organophosphorous extractants that were unavailable when the MIBK process was developed.

Jan 1, 1998

By R. A. Cattell

Every finding of the year's work, obtained under stress to meet present objectives, contributed to postwar needs, because the very nature and constitution of petroleum and natural gas require that research be conducted along the same general lines whether the results are applied in peace or war. More than 40 reports were submitted to the Petroleum Administration for War and others concerned with (1) evaluation of crude oils to determine their content of aviation-gasoline base stock, (2) evaluation of base stocks for blending with high-octane, synthetically manufactured components, (3) analyses of naphthas to determine their content of various types of hydro-carbons, such as benzene and toluene, and (4) the improvement of quality of marginal base stocks to meet future requirements of aviation gasoline. This upgrading of marginal stocks is being attained by selective distillation and chemical and catalytic removal of sulfur compounds. Asphalts were studied with respect to the characteristics of their various constituents in order to compound them, in the same way that aviation fuels now are being "built" to meet exacting requirements. The work previously initiated to give the industry fundamental data on thermodynamics of hydrocarbons progressed satisfactorily, and the heats of combustion of 10 hydrocarbons in the lubricating oil -range of petroleum were determined. Thermodynamic data requiring highly specialized techniques are so broad in application that their commercial usefulness is not yet fully appreciated.

Jan 1, 1946

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By D. S. Case

"Following a brief explanation of the land arrangements under the Alaska Native Claims Settlement Act, this paper will examine both a mineral exploration agreement and a mining development agreement negotiated between two large mining companies and two different Alaska Native institutions. One of the institutions is a village corporation involved with an exploration agreement and the other is one of the Alaska Native regional corporations, which is party to a mining and development agreement with Cominco Alaska for the development of the Red Dog lead and zinc mine.Special attention will be given to the factors to be considered when dealing with small aboriginal owners with few resources in the context of an exploration agreement, including development issues which must be considered early in the process. The paper will also discuss the unique royalty and taxation structures developed for the Red Dog Mine Agreement as well as environmental issues. The paper will also consider the ways in which the cultural and differing economic interests of an aboriginal owner and a large mining company have been accommodated in the both the exploration and development agreements"

Jan 1, 1998

By Y. V. Vasylchuk

An algorithm is presented for optimizing the classification of surface mine material subject to excavating constraints. High-resolution, expected-profit models are optimized to classification maps subject to site-specific excavating constraints. This optimization problem defies traditional closed-form analytical solutions. A practical heuristic algorithm quickly determines the optimum final destination for material subject to realistic selectivity constraints. The expected profit could be calculated from an estimated model if the value calculations are all linear; otherwise, simulation could be used. In both cases, a single expected profit for all destinations on a high-resolution grid is the starting point for dig limits optimization. Maximizing expected profit in a risk-neutral manner is correct given the repeated nature of grade-control decisions over relatively short timeframes.

By W. A. Gow, G. M. Ritcey, M. C. Campbell

"Uranium is a unique commodity. It is both a metal and a fuel, It has both commercial and military uses. It yields ""clean energy "" but presents environmental concerns. All of these factors have an impact on the commerce of uranium.Being a metal, uranium is extracted from ore like many other metallic minerals. As a fuel, it is subject to the vagaries of energy commodity market forces. The history of uranium in the first nuclear weapons has led to nation al governments carefully controlling production and sale of uranium. The spectre of radioactive contamination of the environment adds further to the public concern over the disposal of low-level radioactive wastes from uranium processing and use.There have been a number of excellent reviews on the commercial aspects of the uranium industry. In this discussion, these aspects will be briefly summarized to provide a general picture of the strengths of the Canadian uranium industry and the pressures to which it is being subjected currently. The principal thrust of this paper will be to outline Canada's resource strength and to identify some factors which will affect Canada's ability to continue holding a sizeable share of the world uranium market."

Jan 1, 1985

By S. E. Khalafallo

The Bureau of Mines investigated the kinetics of reduction of wustite and magnetite with carbon monoxide. A mechanism was postulated wherein the interaction between gaseous and absorbed carbon monoxide appears to be the rate-determining process. This mechanism fully accounts for the experimental rate equation JL.h relates th velocity of reduction to the pressure of the reducing gas at constant temperature. It also explains the variability of the heat of activation of the reduction process with the state of aggregation of the oxide material. The integrated rate equation is in perfect agreement with the experimental reduction-time curves.

Jan 1, 1966

By Felipe Darabas Rzatki

Polyether ether ketone (PEEK) is a high performance thermoplastic often selected for high temperature tribological applications under chemically aggressive environments. The present work evaluate the tribological behavior of a high performance PEEK composite under ambient and high temperature (30 and 80°C, respectively). The atmosphere was also varied (air or tetrafluorethane). An AMTI tribometer equipped with a hermetic chamber and a heating system was used to carry out sliding tests of PEEK cylinders on 304 stainless steel polished discs (Sq < 10 nm) with reciprocating movement and 175 N normal force. Surfaces roughness analyses were performed with a white light interferometer. As expected, there was a strong influence of temperature on the tribological behavior of the samples tested in ambient atmosphere (25% decrease in friction coefficient associated with a 100% increase in wear rate). On the other hand, samples tested in tetrafluorethane atmosphere showed no significant friction temperature dependence.

Jul 31, 2018

By Bruce Cantrell, K. L. Rubow

"INTRODOCTIONMeasurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and Chemical Mass Balance (CMB) modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample.Size selective sampling is being adapted for measurement of diesel aerosol by the Particle Technology Laboratory (PTL) of the University of Minnesota under sponsorship by the Bureau. 1 It is based on the premise that diesel and mineral dust aerosol can be physically separated by size and collected during sampling using inertial impaction. An independent effort by the National Institute for Occupational Safety and Health to develop a size selective sampling technique was also sponsored by the Bureau.The second technique, CMB modeling, is being developed by the Bureau as an alternative measurement technique to referee the results obtained using size selective sampling.3 It compares measured trace element ""finger prints"" of aerosol sources with similar profiles of mine aerosol samples. From these, the portions of the sample contributed by each source can be determined. Results of these investigations in underground coal mines have confirmed that diesel and coal dust aerosol are of different size and can be measured separately using size selective sampling techniques.A major difference in diesel usage among underground mines is the requirement for exhaust gas cooling systems in coal and gassy noncoal mines. Nongassy mines usually employ limited exhaust conditioning in the form of catalytic converters, which have limited effect on primary exhaust particulate. The cooling system in most general use in gassy mines is the water scrubber. This device has little effect on most of the gases but removes particulate material from the exhaust. 5 Because of this, exhaust aerosol characteristics in nongassy mines are expected to be different. To see if size selective sampling techniques can be used in such mines, the Bureau and the University of Minnesota conducted a second study in three metal and nonmetal mines, two nongassy and one rated as gassy."

Jan 1, 1990

By Huaqing Xie, Qingbo Yu, Qin Qin

A novel sorption-enhanced steam reforming (SESR) process of hot coke oven gas (HCOG) was proposed for tar removal and H2 amplification, and was studied with the comparison of conventional steam reforming (SCR) process. Both of the processes could remove tar effectively and improve the H2 amount in the COG obviously. For CSR process, after the temperature and the S/HCOG ratio reached 700 °C and 2.4 respectively, the H2 amplification factor kept 4.30 around, with its concentration less than 75%. However, for SESR process, the H2 amount and concentration get improved further, with the optimal temperature moving toward low temperature. At 600 °C and the S/HCOG ratio of 2.4, the H2 amplification factor and concentration could reach 4.91 and 97.55% respectively when the CaO/C ratio was 2.0. Under the respective optimal reforming conditions of the two processes, the energy consumption of the SESR process was lower than that of CSR process.

Mar 1, 2018

By Evan Bennet

El presente texto señala la situación del carbón en el valle del Santa, al tiempo que busca reivindicar su posición, producción y demanda del mismo. Para ello, el doctor Fraser describe las características del mineral, encontrando que el carbón del tipo "La Limeña" contiene una elevada gravedad y friabilidad, como un buen porcentaje de los "middlings". Posteriormente se realizaron pruebas como la del carbón R.O.M. en una planta Bradford improvisada, demostrando que el carbón y los "middlings", se trituran fácilmente gracias a la friabilidad del mismo y que el producto de tamaño mayor puede ser escogido a mano fácilmente para su disposición futura. Mientras que las pruebas de diversas clases de "middlings", evidencian dificultad en el tratamiento para la recuperación de carbón puro, pues el triturado a tamaños finos libera sólo pequeñas cantidades de carbón "float", manteniéndo su calidad inferior en comparación con los finonaturales, que se trituran fácilmente del R.O.M. y del producto de la planta Bradford. De otro lado, se describe el beneficio del carbón en las minas, la conservación de maquinaria, uso de briquetas, el empleo del ferrocarril como transporte y las instalaciones de las plantas lavadoras del banco minero en Chimbote y planta pallasca en Chimbote.

Jul 20, 1956

The deep seafloor in Papua New Guinea&apos;s proposed Exclusive Economic Zone appears to be a gold-rich province in the same sense as the territory above sea level. Two significant sites with polymetallic massive sulphide deposits forming today are known on neovolcanic ridges in the Manus Basin. Their high precious metal contents have led to renewed interest in the issue of exploiting seafloor mineral deposits. The prospects of finding other, possibly larger deposits in the region appear substantial. This paper reviews current data on seafloor deposits in Papua New Guinea (PNG) and raises some issues relating to future commercial exploration and mining of the sea floor. One of the known PNG deposits could become a prime candidate for the trials needed to develop technology, establish costs, and minimise environmental impact.

Jan 1, 1994

By L. M. Scovell

The Internet and its related technologies will radically change the way that mines manage and control their maintenance, repair, and operating supply chains. The Internet is creating new distribution channels and offers new technology platforms with significant advantages over more traditional methods. Mines will have to re-evaluate both the strategies and the tactics employed in these areas. Mines will use e-commerce to integrate their maintenance, repair, and operating supply chains. The integration will extend beyond traditional trading partners to a worldwide network of communities with similar interests and goals. The changes will transform the way mines operate, lower mining costs, and thereby increase their chances of success in an increasingly competitive environment.

Jan 1, 2000

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997