Search Documents

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012

By B. C. Parks

This is the first of a series of reports on the relation between microscopic composition and chemical and physical properties of banded bituminous coals. It describes the relation between microscopic composition and behavior during thermal decomposition of a heterogeneous, high-volatile A bituminous coal from the Chilton bed in West Virginia. The standard free-swelling test was used as a simple means of studying the effect of heat on the coal. Although swelling indexes are not precise indicators of coal behavior in the coke oven and have limited value in caking investigations, they are reliable for predicting expansion of coal in a fuel bed and have practical value in the study of fuels. The swelling test also supplements other useful laboratory tests for determining the plastic and expansion properties of coal.

Jan 1, 1957

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

As indoor positioning provides particular challenges due to the unavailability of GPS signals, various systems such as ultrawideband (UWB), radio frequency identification (RFID), ultrasound, and wireless local area network (WLAN) have been proposed in recent years. Some of these technologies are currently being marketed and some are still being developed. UWB technology allows for higher precision while also reducing power consumption. Hence, the underground automation and localization systems can use this technology for more accuracy and robustness. This article discusses new robust UWB modules used for underground positioning and collision avoidance with regard to human safety in underground mining operations.

Jul 31, 2020

By David White

ATTENTION has been given to the sources and supply of the raw vegetal matter and. the conditions of its submission to the process of sedimentation. An original and most valuable review has been made of the more important or significant chemical compounds originally contained in the organic debris, and of the biochemical changes-undergone by the latter during deposition. Consideration also has been given to the factors controlling the selective biochemical decomposition, in whole or in part, of :this debris, and the deposition, as, sediments, of the undecomposed plant structures and compounds, together with more or less of the so-called "ulmic," or "humic," organic decomposition products in colloidal solution.1 BIOCHEMICAL CHANGES END IN PEAT FORMATION The biochemical process terminates in the peat stage of coal formation, and with the cessation of this process organic sedimentation is completed. All subsequent changes result from geological causes and conditions. The deposits are in the form of peats of different types, organic muds, oozes, etc. They are essentially uncompressed and are wholly unconsolidated, and their water content is great, amounting to over 85 per cent. near the surface of the deposit. Many of the chemical compounds remain as in the once living organisms; others are biochemically broken down and new ones formed.

Jan 2, 1925

By Darren Medd

Kumtor Gold Company (KGC) currently operates the 500,000 tonnes per day Kumtor open pit gold mine located in the Issyk-Kul region of the Kyrgyz Republic at an elevation of more than 4,000 m. To supplement the open-pit mill feed with high grade underground ore from outside the current pit limits, KGC started pre-production design and development of the underground mine for the SB ore zone in late 2006. The initial phase of pre-production development consists of exploration and haulage declines which, upon completion, will provide ventilation and access to the underground mine. Design and construction of these declines presented many challenges to the project team considering the mines unique location at high altitude, the limited experience with Western underground mining techniques in the Kyrgyz Republic, and the impact of the nearby Davydov glacier and resultant ground conditions. Completion of the exploration and haulage declines was undertaken jointly by KGC and mine contractor, J.S. Redpath Limited (Redpath). The initial phase of development including several ground falls provided detailed information on geotechnical ground types and conditions that were useful in determining the overall mine design and methodology for production. This paper covers the various aspects of the design and construction process of developing the declines under the glacier, minimizing the likelihood of further ground falls, and the journey of both KGC and Redpath which led to the successful breakthrough between the declines on 01 July 2012.

Aug 1, 2013

By Steven J. Schatzel

Large-scale methane releases in dual salt mines have resulted in ignitions and mine fatalities as recently as 1979. Several past studies have implied that hazardous methane occurrences in U.S. salt domes are distributed neither uniformly nor randomly, but are geologically controlled and potentially predictable. A first step by the Bureau of Mines in addressing the problem of methane in deal salt mines required development of a new test to determine volumes of gases in solid salt samples. This report considers the results achieved when 80 deal salt samples were tested for gas content by dissolution in a controlled atmosphere chamber. Criteria were organized to delineate salt types based on geological occurrence. Outburst samples range from 0.014 to 7.4 cm3 CH4/100 g NaCl, anomalous salt samples from 0.0027 to 2.6 cm3 CH4/100 g NaCl, and normal salts from less than 0.0003 to 0.31 cm3 CH4/100 g NaCl. The presence of higher hydrocarbons was most common in samples containing larger quan¬tities of methane. The presence of higher hydrocarbons appears to be useful in detecting methane hazards where some methane may be lost before gas content testing. An exploratory rotary and/or core drilling program, dissolution testing for gas content, and up-to-date geologic mine napping could allow a mine operator to assess methane hazards in dual salt.

Jan 1, 1984

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

"The methods and technologies to be used for environmental monitoring of seabed mining activities are a key issue. Due to the large water depths, there are special challenges with respect to the monitoring equipment that is suitable. DNV GL has built up substantial experience of environmental monitoring from oil & gas projects in deep waters in the Norwegian Sea.Monitoring equipment and experiences from the oil & gas sector can to a large extent be applied to seabed mining.BackgroundThe International Seabed Authority is currently developing an environmental management strategy for the Area (ISA, 2017) as a part of the work on the regulations for exploitation for mineral resources in the Area.The draft environment strategy contains provisions related to monitoring and reporting of the activities. An Annex (Annex III) of the draft document describes the format and content of the environmental management and monitoring plan.The monitoring plan should contain, inter alia: ?Technology to be deployed.?Monitoring frequency of respective elements/components of the Marine Environment.?Monitoring procedures required to implement the Monitoring programme.?Details of the environmental monitoring stations across the Environmental Impact Area.?Monitoring specifics e.g. water quality; sedimentation rates; sound; plume extent; etc., as well as relevant Environmental Targets.?Monitoring of Mining Discharges.?Processes for Monitoring reviews and Environmental audits."

Jan 1, 2017

By Johan Finsteen Gjodvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad.

Feb 1, 2020

By Alexander B. Morris

Studies such as the investigations into the solubility of gases in crude oil under various conditions, which have been carried on during the past three or four years, are very interesting from an academic point of view, but this consideration alone is hardly sufficient to warrant the large contributions from the industry necessary to maintain them. Some definite benefit to the industry as a whole should be forthcoming. The purpose of this paper is to direct the attention of company engineers, and company executives, to some of the ways in which the information gained from these studies can be made directly profitable. This work has two principal economic aspects. One affects the investment budget, and through it the financial requirements of the companies. The other affects operations, and through this course is reflected in current earnings. It will be shown that, as a direct result of the investigations into gas solubility, undertaken in the recent past by various investigators, it is now possible: 1. To determine more accurately the amount of reservoir oil originally present. 2. To obtain closer control on operating conditions, to effect more economical recovery. 3. To predict earlier and more dependably when and how much surface lifting equipment will be needed. 4. To reduce, or entirely avoid the very large investment in gasoline recovery equipment now frequently found necessary. 5. To control the gravity of the pipe-line oil so as to secure the greatest possible revenue from the products of the well. 6. To effect the recovery of a large amount of gasoline now wasted while the practicability of a gasoline recovery system is being decided. 7. To plan operations, by comparison with the history of old properties operated without this new information, so as to avoid the mistakes of ignorance made in the past. These points will be discussed in the following pages, though not necessarily in the order stated. There is so much overlapping of the points themselves, and of the data from which they have been drawn as conclusions, that to treat them in any particular order would require

Jan 1, 1935

By Renato G. Bautista, David C. Lindholm

The results of scale-up studies on a continuous, multistage horizontal mixer-settler extractor are presented. The chemical and mechanical system involves the separation of lanthanum from a mixture of rare earth chlorides using di(2-ethylhexyl) phosphoric acid as the solvent and dilute HCl as a scrub solution in a bench scale extractor. Each stage has a hold-up of 2.6 l. A single stage unit is utilized for scale- up studies. Results are obtained on four sizes of geometrically similar units, the largest being six times the volume of the original bench size. A unit operations technique is chosen so that mixing and settling can be examined independently. Variables examined include type of continuous phase, flow rate of inlet streams, and power input to the mixer. Inlet flow-rate ratios are kept constant for all tests. TWO potential methods of unbaffled pump-mixer scale-up are explored; the maintenance of constant impeller tip speed and constant power input. For the settler, the previously successful method of basing design on constant flow-rate per unit cross- sectional area is used.

Jan 1, 1977

By G. Grassmück

The question of whether the air curtain principle could be used under conditions prevailing in Canadian metal mines was investigated. A vertical, portable BERRY air curtain was tested, at first in a wind tunnel built at Ecole Polytechnique at full scale (8-by 8-ft cross section) to simulate a drift and its lateral connections, and then in the haulage ways of a metal mine under actual conditions. The results permit us to predict under what conditions this type of air curtain is capable of acting as an air stopping or flow regulator and how it could be further developed.

Jan 1, 1969

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By Oliver Bowles

The use of fire as a source of heat was the first step from primitive existence toward modern civilization, and heat has performed functions of inestimable importance throughout the ensuing ages. The first commercial steam engine invented in 1698 demonstrated that heat was an important source of power, and heat has since become the motivating force for railroad trains and steamboats as well as for machines in multitudes of factories. Aside from its function of supplying power, heat is an agent of vast importance in chemical reactions and engineering processes. Because of the high temperature of steam under pressure, losses by radiation from boilers and pipes become excessive unless the radiating surfaces are covered with insulating materials. Insulation is important also for hot-water pipes and many other types of equipment from which heat may radiate. Radiation losses from heated surfaces increase rapidly

Jan 1, 1943

By Leslie McHattie

?Intelligent mine? conjures up a futuristic image of unmanned extractors and loaders working in harsh conditions in a remote lunar landscape. The promise of increasing mine fleet productivity and solving the problem labor shortages in mining regions can certainly be achieved today through remote controlled extraction and automated hauling. The technology is available and it doesn?t seem to be so much science fiction when Google?s self-driving cars hurtle down the freeway. ?Intelligent mining,? on the other hand, implies the application of information technology at every phase of the mining value chain, from exploration and geological modeling to equipment, operations and maintenance, and logistics and transportation. These are really industry-specific, enterprise-class software solutions focused on using information technology to support the business processes of mining and make them more efficient and effective. Overlaying the physical world with the digital or virtual world enables us to model and simulate our assets, giving us the ability to effectively design, build, and ultimately optimize the performance and reliability of our assets throughout the lifecycle. The digital asset, often a 3D model, is created initially during the engineering and construction phase, and is handed over to the operator before the mine goes into operation. Combined with geospatial or geographic information systems, the operator has a complete digital representation of the physical world, which forms the foundation for risk and performance management, along with compliance and regulatory reporting. Laser scanning and positioning technology can be used to create point clouds ? information models consisting of millions of data points ? which enable the visualization and representation of the ?as-operated? reality. But consider that once the mine is in operation, it throws off an endless stream of data in the form of performance and condition data from sensors and monitoring devices on fixed and mobile assets through networks, servers, and services. This ?big data? can be processed and analyzed to spot trends, help predict events, and formulate reliability strategies as early as the design stage (e.g., reliability-centered design). ?Intelligent mining? implies that massive amounts of data augment the reality of the physical mine, plant, and equipment. This embedded intelligence can be used to optimize operational efficiency, increase asset availability and utilization, improve safety and environmental integrity, and maximize return on investment. Lastly, the sweet spot for intelligent mining is seen in the convergence of consumerization and industrialization. The application of ?consumer? technologies that we use every day on our iPhones and Android devices, such as cameras, motion sensors, and positioning in an industrial context, are producing ?immersive? experiences. Overlaying the digital world on the physical world and connecting them accurately through intelligent positioning results in ?intelligent infrastructure,? which is safer and more sustainable. Bentley Systems works with many mining companies and engineering, procurement and construction companies involved in all aspects of mining infrastructure development. In fact, 10 of the top 20 mining companies ranked by market capitalization are users of Bentley software, including all of the top five. In addition, Bentley provides software solutions to the world?s leading engineering, procurement, and construction companies, as well as owner-operators, who design, build and operate the world?s infrastructure. Bentley?s solutions for mining and resource extraction industries help increase the efficiency of capital projects associated with the design, procurement, and construction of mines and processing plants, as well as the operation and maintenance of mining fleet and equipment.

Aug 1, 2013

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By H. Kudelka

Copper electrowinning at Duisburger Kupferhuette was introduced in March 1975. The electrowinning plant has a capacity of 10,000 mT of copper cathodes a year. The cuprous oxide feed material is an intermediate product of the treatment of the leach solutions, originating from chloridizing roasting of pyrite cinders. This material is characterized not only by a wide spectrum of accompanying impurities, but also by an unusually high level of precious metals. As the priority set was the production of high-purity cathodes. there was a need for developing a process which would be suited to treat complex leach liquors . The process adopted consist s of an oxidizing leach in spent electrolyte, followed by two- stage purification, By this means. a low- acid pregnant copper electrolyte is obtained free of elements detrimental to copper quality. Electrowinning is carried out at a current density of 200 A / m2 in the presence of 10 g/l zinc. The electrowon copper has a conductivity of at least 101.4% lACS and a softening temperature not exceeding 200°C, which makes it a suitable product for continuous casting and dip ?forming.

Jan 1, 1977

By M. Tangstad, J. D. Steenkamp

In April 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. Since the high shell temperatures recorded in the tap-hole area resulted in the furnace being switched out for relining, the tap-hole area was excavated systematically. A refractory wear profile of the tap-hole area with affected hearth and sidewall refractory was obtained in elevation. The carbon ramming paste in front of, above, andbelow the tap-hole was worn, as was the SiC with which the tap-hole was built. A clay mushroom formed but was detached from the refractories. Thermodynamic and mass-transfer calculations were conducted to quantify the potential for wear by chemical reaction between refractory and slag and refractory and metal in the tap-hole area. It was found that chemical reaction between refractory and slag or metal could offer only a partial explanation for the wear observed; erosion is expected to contribute significantly to wear.

Jan 1, 2015

By Scott Turner

MY YEAR OF SERVICE as president of the A.I.M.E. came at a time when the mineral industry had suffered severely because of disturbed economic conditions throughout the world. The Institute, an integral part of this industry, had been similarly affected. Its membership and revenues decreased; it was confronted by problems of retrenchment at a time when its vigorous operation was especially important to its members, of some moment to the mining industry, and of value to the nation. Throughout the last year, the recession of activity in our industry continued with slight abatement. Your Board accordingly exercised such economy within the Institute as was possible without impairment of essential functions. It endeavored to aid in sustaining the morale of members, their sense of professional unity, and their interest in maintaining research and the interchange of scientific and technologic data upon which the progress of our industry depends. Effort was made to assist in the difficult task of finding employment for needy members; our endeavors have met with some success.

Jan 1, 1933

By Kuzmitch O, Morozov A

The main direction in the mechanisation in the mines of the Donbas and the USSR is long-face technology with complexes on the base of hydraulic supports. On the base of the 30 year old experience of exploitation of the coal clearing systems the serious data about the behaviour of the contained rock, display of underground pressure 'on longwalls and preparatory workings have been accumulated. Exploitation works in mines of the USSR are carried out at different depths: from 1000m to 1200m. There are 26 mines in Donbas, which exceed the depth of 1000m. It is the mines of Donbas, where is a rich experience of the exploitation of coal seams in various conditions. Besides, there are wide variations on the factors of the extraction thickness, depth of seam, angle of dip, occurrence of gas dynamics and others. In many scientific establishments, and in Donetsk Polytechnical Institute also, there are scientific research/results, which can be of interest for the coal mining countries.The volume of coal mining from longwall system-mechanised walls in Donbas became stable at the end of the 70s at level of 70 percent. All the efforts to increase this level have not given any notable results, not saying about the technical-economical data, which gradually deteriorate. It shows that positive progress in using the technology for the long walls is over and it is necessary to find new ways of mechanisation of coal winning.

Jan 1, 1991