Search Documents

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department's Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed Formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By William M. Thornton

[Owing to the comparatively high freezing point of nitroglycerin (14, 15, 16, 17, 18, 23, 37, 38)3/ - 1.9° C. and 13.0° C. for the labile and stabile modifications, respectively, as determined by Hibbert (16) - manufacturers of dynamites have incorporated into the liquid portion of these composite explosives various substances capable of participating in an explosion, to depress the above-mentioned freezing point. Aromatic nitro-compounds, chiefly nitrobenzenes, nitrotoluenes, and nitronaphthalenes, have been used to a considerable extent (11), but such nitrosubstitution products have not proved altogether satisfactory, as has been shown clearly by Naoúm. (14). Consequently there has been a strong tendency in recent years to replace them with one or more of several nitric esters, among which the following (29, 35) have been prominent: Dinitrochlorhydrin (monochlorhydrin dinitrate); nitrosugars, for example, sucrose octanitrate (19); tetranitrodiglycerin (diglycerin tetranitrate); nitroglycol (ethyleneglycol dinitrate); and diethyleneglycol dinitrate (13, 46, 47). Of these, nitroglycol (33, 4l, 45, 48, 49, 65) is outstanding in importance. As the Bureau of fines is naturally interested in the analytical chemistry of the "explosive oils," it seemed desirable to bring together in this report the widely scattered experimental work covering the problem of differentiation that has appeared in various chemical and physicochemical publications.]

Jan 1, 1941

By A. Tewarson

Combustibility data are presented for 14 samples representing commonly used mine materials (treated and untreated wood, conveyor belt and brattice cloth). The combustibility data were obtained in the Factory Mutual Small-Scale Combustibility Apparatus (sample area -0.008 m ). The hazards associated with the mine materials were evaluated in terms of: 1) ignition/ surface flame spread using an ignition parameter (IP). A reasonable correlation was found between IP values and U.S. Bureau of Mines ratings for conveyor belts and brattice cloth and large-scale fire test data for treated and untreated timber sets; 2) generation of combustible vapors, using a vapor generation parameter (VP); 3) heat release using a heat generation parameter (HP). A reasonable correlation was found between HP values and the large-scale fire test data for treated and untreated timber sets; 4) generation of "smoke," toxic and corrosive products using a chemical compound generation parameter (CP); and 5) light obscuration by "smoke" using the light obscuration parameter (LP). All the wood treatments, except Fireguard, were found to be effective in reducing the fire hazard. The effectiveness of the treatment appears to be due to enhancement of carbon formation in the solid phase and enhancement of water formation in the vapor phase. Concepts are presented for establishing 1) the relationship between various parameters (IP, VP, HP, CP, and LP) and basic properties of materials, and 2) the usefulness of the parameters as criteria for the combustibility and fire hazard evaluations of the mine materials.

Jan 1, 1982

By William K. Cunningham

The investigation described in this report was begun as part of the Bureau of Mines progress to develop acid processes for the extraction of alumina from low-grade bauxite and. clays. A domestic shortage of high-grade bauxite sui table for treatment by the Bayer process became acute as a result of' World War II; an intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted. The laboratory development was described in a preceding Bureau of Mines publication wherein the basic theory for the design and erection of a pilot plant maybe found. A 2-ton-per-day continuous pilot plant was constructed and successfully operated at College Park, Md., which demonstrated conclusively the chemical and mechanical feasibility of a solvent purification process for aluminum sulfate. The estimated production cost of $38.64 indicates that under present market conditions the process would not be economically feasible.

Jan 1, 1948

By J. Roger Loebenstein

Demand for arsenic trioxide exceeded supply in 1978 and 1979, and the major domestic and foreign producers allocated available supplies to customers. Major demand has been from the cotton-growing and wood-preserving industries. Ample supplies of arsenic metal produced in the United States and Sweden were available in 1978 and 1979. Major demand for metal was from the automobile battery industry in Japan, Europe, and the United States. Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA), promulgated the final standard on the occupational exposure to inorganic arsenic, effective August 1, 1978.2 The need for the standard was a result of OSHA's conclusion that inorganic arsenic is a human carcinogen. The purpose of the standard was to minimize the incidence of lung cancer among workers exposed to inorganic arsenic. The maximum exposure to arsenic was lowered from the previous ceiling of 500 micrograms per cubic meter of air to 10 micrograms per cubic meter over an 8-hour time period. OSHA had originally recommended a ceiling limit of 4 micrograms per cubic meter in January 1975. Provisions of the new standard require exposed employees to wear respirators and undergo continuous medical monitoring. Other provisions establish regulated areas limited to authorized employees and require the construction of special lunch-room and worker hygiene facilities and the posting of signs and labels warning of the presence of arsenic. The new arsenic standard will have a significant economic impact on copper, zinc, gold, and lead smelters as well as consumers of arsenic trioxide. A number of copper companies have joined together to contest the standard in court. However, measures to comply with the standard have been initiated by ASARCO Incorporated at its Tacoma, Wash. plant.

Jan 1, 1980

By A. Dubé

Introduction It is common experience that on re-heating a fully martensitic steel below the Ac, point, a softer and tougher structure is formed as the tempering temperature is raised. The mechanism of tempering of plain carbon and low-alloy steels has been the subject of many investigations. In a very comprehensive study, Cohen and associates have recently established three different tempering stages, the last of which reaches completion at about 700°F., with heating rates of 5°F. per minute. This latter stage has been established ta be the carbide-forming stage, so that the steel consists of a mixture of ferrite and carbide, which are the metastable equilibrium phases. Any subsequent changes which take place at higher temperatures below the Ac, point in the absence of graphitization or carbide lattice conversion normally consist of agglomeration of the carbide particles. This naturally results in the softening of the steel. However, in many cases the Ac, point, as determined by dilatometry, thermal analysis, etc., only gives a rough estimate of the temperature where the reaction, ferrite plus carbides to austenite, is initiated. This appears to be especially true in the case of alloy steels in which three phases can co-exist in certain temperature ranges. Bain has given data on the three-phase equilibrium in both manganese and nickel steels. In these steels, the formation of austenite at temperatures just above the AeIL apparently involves the diffusion of the alloying elements to the first pools of austenite, thereby making the process very sluggish. As a consequence, the critical Ac points determined by ordinary methods at normal rates of heating can be quite distant from the true equilibrium Ae temperatures.

Jan 1, 1946

By Seth T. Reese

THE INJURY and related employment experience of the coking industry in the United States for 1953 contained in this bulletin are presented under three general sections, as follows: (A) General injury experience: Tables 1 to 9: Contain current and comparable statistics on operating data, number, frequency, and severity of injuries, and major accident agencies involved in the cause of injuries. Data are tabulated for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data covering 5- and 10-year periods on the number and severity of injuries and major accident agencies. (C) Historic injury experience: Tables 1.6 to 19: Contain data on the number and rates of injury occurrence and related employment statistics on the industry from the earliest records through 1953.

Jan 1, 1955

By M Francoeur

Oct 12, 2022

A new horizontal borehole packer for use in coal beds has been developed. This packer utilizes a principal of operation which has not previously been used. The resulting packer is less costly to purchase, can be easily repaired in the field with inexpensive expendable parts. This report describes the development and testing of the new packer and the evaluation of commercially available packers.

Jan 1, 1971

By F. T. Rabbitts

Introduction When the investigation of radioactive ores began at the Mines Branch about five years ago it was at once evident that improved chemical methods for the determination of uranium were essential. The published methods available were time-consuming and insensitive and were lacking in accuracy and precision. It was desirable to obtain methods which would be rapid, sensitive, and accurate. They should also allow for the possible presence of any interfering elements and should be adaptable to routine analysis by technicians. Chemical methods are necessary to provide standard analysed samples for counting and to check analyses by counter methods. Moreover, counter methods cannot be used, and only chemical methods are suitable, when the sample is not in equilibrium, as with weathered minerals and leach residues. As leaching processes are improved, more sensitive chemical methods are required for the increasingly lower content of uranium in the leached residues. When the leaching process reaches the plant stage, speed of analysis becomes more important, without sacrificing accuracy. The purpose of this paper is to describe briefly .the methods used at the Mines Branch for the chemical analysis of uranium in ores. These methods represent the results of investigations by a number of groups in the United Kingdom, the United States, and Canada.

Jan 1, 1952

By Paul M. Tyler

Graphite is an essential war mineral and for that reason has received much attention from the standpoint of national defense. During the World War the situation with respect to graphite supplies, though it never became acute, caused considerable concern. Even in peace time, however, graphite has aroused more interest than the actual size of the industry seems to warrant. Despite this wide interest the facts of the industry do not seem to be generally known. Often there has been an almost total disregard of the essential' economic and technical problems involved. Long ago Bastin3 made the following statement; in a Government' report: "To-day there are more abandoned mines and mills in the United States than the number in operation * * *. In the number of times' some of these properties have changed hands in the course of a few years, there is a record of misrepresentation and disappointment that can hardly be equaled in any other branch of mining; and many properties have been notoriously associated with stock manipulation of doubtful character." According to one authority fully 600 graphite mines have failed in the United States, and the record shows that of all these properties scarcely a score have ever succeeded in operating for as much as a year or two. More than 40 mines have been worked at various times in the State of New York alone and at least that many in Alabama. Throughout the country, in fact, there are scarcely a dozen States in which efforts have not been made at some time to exploit graphite deposits. At the present time the list of mines that can be classed as at all active is reduced to less than ten. Failures inevitably occur in all lands of mining, but the disheartening feature of the record of graphite mining in this country is that so few ventures have even paid back the money put into them and. that none has been a conspicuous success.

Jan 1, 1929

By G. G. Krishna Murthy

Several experiments were carried out to simulate the bath smelting reactions where iron oxide particles were dropped on to an iron-carbon bath containing molten CaO-SiO2-Al2O3 slag layer on its surface. The composition of the slags used in the experiments was %CaO:46.1; %SiO2:41.7; and %A1203:12.2. Experiments were con¬ducted with carbon saturated iron melts contained in either a pure graphite crucible whose walls were covered with a pure alumina tube, or a pure flat bottom alumina crucible, at 1723-1823 K. Degree of reduction of a pure iron oxide particle was linear with time in the initial stages (up to about 20% oxygen of the original pellet was reduced). The rate of reduction of smaller oxide pellets was smaller than that of a bigger pellet - the time for complete reduction of a 5.6 g wustite pellet was smaller than that for a 1.2 g wustite pellet. It was also established that the interaction rates obtained by adding a molten pure oxide particle of given weight to the system were lower than that determined by using a solid oxide particle of same weight. The overall rates of reduction decreased with decreasing the bath temperature. The experimentally determined rates of reduction based on the time for 70% reduction were influenced substantially by addition of slag up to about 50 g on to a bath of 78.8 mm in diameter, and remained constant when slag present on the bath surface was between 50 g and 200 g.

Jan 1, 1993

By Kevin Saeler, Patrick Willaman

Utilizing automation is one way to improve competitiveness. Roof and rib bolting in underground coal mines has not changed significantly for more than 40 years. Most roof bolting is still a largely manual process involving high levels of staff carrying out repetitive work. Roof bolting statistically has one of the highest levels of underground accidents, including finger, hand, and arm injuries. Operators are exposed to falling objects and becoming entangled in roof bolting apparatus while roughly moving awkward 6-ft drill steels and roof bolts. It is estimated that over 25 million roof bolts are installed annually in the U.S. underground coal market with well over 1,500 operators involved in roof bolting on a day-to-day basis. Recently electrohydraulic roof bolting rigs have been installed to offer partial automation of the drilling cycle and the bolting cycle. The next stage is to provide a storage and loading system to allow full automation of fullcolumn resin roof bolts. This paper reviews the latest electrohydraulic roof bolting equipment and discusses the testing of a fully automated drill rig. Full electronic control allows each step of the roof bolting process to be recorded, providing a digital record of each installation, including hole depth, spin time, gel time, torque, and cycle time. Other benefits include monitoring of water pressure and flow, used to prevent blocked drill steels as well as digital fault finding. A fully automated roof bolting machine greatly improves operator safety and gives high-quality repeatable roof bolting with reduced cycle times.

Jul 1, 2023

By Douglas A. Elkins

The unique characteristics of plasmas, their current applications, and ongoing research into new applications are described. Major technical and economic problems in application of plasma technology are discussed. Examples of potential applications of plasma in extractive metallurgy are described and evaluated. The report includes a selected bibliography of articles on plasma and related high-temperature technology.

Jan 1, 1969

By G. J. Slavens

The U.S. Bureau of Mines conducted research on preparing submicrometer titanium nitride (TiN) powder as a substitute for tungsten carbide (WC) in cutting tools and wear-resistant parts. Earlier research on a small scale was expanded to include a larger reactor. The TiN powder was produced by contacting titanium tetrachloride (TiCI4) with anhydrous ammonia (NH3) in the presence of Mg at 1,100° C. The powder was collected in an electrostatic precipitator (ESP) filled with ultra-high-purity (UHP) Ar. All collected powder was thermal vacuum distilled to remove Mg and magnesium chloride (MgCl2), leaving the purified TiN. Powder handling and purification procedures were conducted to assure low oxygen content in the powder product. Oxygen content in the distilled TiN powder product was as low as 0.40 wt pct. Nitrogen averaged near 22.0 wt pet with a high of 22.4 wt pct. The purified powder product had an average median particle diameter of 0.14 µm with a standard deviation of 0.09 µm.

Jan 1, 2010

By G. Graves, J. A. Walker

"Abstract - The Mount Fronsac North volcanogenic massive sulfide deposit is the most recently discovered massive sulfide body in the Bathurst Mining Camp. The deposit occurs within a sequence of intercalated fine-grained felsic tuff and sedimentary rocks (Little Falls member), at the top of the Nepisiguit Falls Formation. Aphyric to sparsely feldspar-phyric rhyolite and related volcanic rocks of the Flat Landing Brook Formation overlie the host sequence. The massive and semimassive parts of the deposit have a north-south strike length of 525 m and a dip of ~45°E; the deposit is continuous downdip for 600 m, and thickness varies from 2 to 20 m. The deposit contains an estimated geologic resource of 14 Mt of low-grade, semimassive (>60%) to locally massive sulfides, and includes a high-grade zone of 1.26 Mt grading 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, and 0.40 g/t Au. The semimassive to massive sulfide intersections occur in an envelope of quartz-sericite±chlorite schist, which is interpreted to be intensely deformed felsic tuff. This sequence has a maximum thickness of 140 m and contains significant (up to 50%) fine- to coarse-grained disseminated pyrite. The pyritic envelope has a strike length of 900 m and extends over 1000 m downdip. Massive sulfides are found throughout this alteration envelope, but more commonly occur at or near the upper contact. The significance of the discovery of this deposit is that it represents a near surface discovery of a large tonnage sulfide body in a mature mining camp, one in which the possibility of discovery of a new shallow deposit had been all but discounted. This opens the possibility for future discoveries in this part of the Bathurst Mining Camp. Sommaire - Le gîte de sulfures massifs volcanogènes du Mont Fronsac Nord est la découverte de sulfures massifs la plus récente dans le Camp Minier de Bathurst. Le gisement est situé dans une séquence de tufs felsiques à grains fins interlités de roches sédimentaires (membre de Little Falls, au sommet de la Formation de Nepisiguit Falls. La partie massive et la semimassive s’étendent du nord au sud sur 525 m et ont un pendage de ~45°E; le gisement est continu sur 600 m en angle de chute et son épaisseur varie de 2 à 20 m. Le gisement contient une ressource géologique évaluée à 14 Mt de sulfures semimassifs (>60%) localement massifs à basse teneur, incluant une zone à haute teneur de 1.26 Mt titrant 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, et 0.40 g/t Au. Les intersections de sulfures semimassifs à massifs se situent dans une enveloppe de schiste à quartz-sericite ± chlorite interprétée comme un tuf felsique intensément déformé. Cette séquence contient une quantité importante (jusqu’à 50%) de pyrite disséminée dont le grain varie de fin à grossier et son épaisseur maximale est de 140 m. L’enveloppe pyriteuse s’étend latéralement sur 900 m et a été tracée jusqu’à 1000 m en angle de chute. Des sulfures massifs sont trouvés partout à l’intérieur de cette enveloppe d’altération, mais ils sont plus fréquents près du contact supérieur. L’importance de cette découverte tient à ce qu’elle est un exemple d’un gisement à fort tonnage nouvellement découvert à une faible profondeur dans un camp minier mature, i.e., un camp ou l’on ne croyait plus qu’il était possible de trouver un gisement près de la surface. Ceci ouvre la porte à la possibilité d’autres découvertes dans cette partie du Camp Minier de Bathurst."

Jan 1, 2006

By John Convey

This paper, a follow-up to an earlier study, gives the history of Canadian developments in mineral processing from 1921 to the fall of 1964. It deals extensively with comminution and flotation, and then goes on to cover the fields of gravity concentration, magnetic concentration, cyanidation, the processing of uranium ores, and instrumentation. Several outstanding examples of installations are given. The paper concludes with a discussion of present-day trends in mineral processing. Introduction T HE history of the developments in mineral processing in Canada from its earliest times to 1920 has already been published by one of the authors (1). The present paper is thus a logical follow-up to bring this history to date. From 1834 to 1920, mineral processing in Canada, as elsewhere in the world, was in its formative stage. This, however, prepared the ground for developments that have resulted in a mining empire from the Atlantic to the Pacific, a mining empire which could be said to be almost on par with that in the United States.

Jan 1, 1965

By A. Y. Senchenko, Y. V. Kulikov

"In recent decades HPGR technology has proven itself in comminution circuits of mining plants. High technical and economic performance, lower specific energy consumption and reliability of HPGR equipment makes it an efficient alternative to conventional circuits using stage crushing and rod/ball milling, as well as to AG/SAG circuits. However, despite all the advantages of this technology the correct selection of key and auxiliary equipment is very important since errors at testing and design stages may lead to discrediting of the whole concept of HPGR application. There is a great variety of possible circuit configurations using HPGR, e.g. with circulation of edge product, with crushing of the whole discharge and circulation of screen oversize, successive two-stage crushing, etc. Each type of minerals will require its own optimal crushing circuit. In this context the testing methodology for selection of an optimal configuration becomes of prime importance. It is common knowledge that the best simulation of material crushing and softening within a HPGR can be obtained only in the course of a large-scale pilot test. The main approaches applied to this kind of testworks are described in this article. Special aspects of HPGR technology design and industrial operation are revealed as well. Some operational issues of HPGR equipment and of circuit as a whole were detected. They are related to regions specifics, plants location, and other factors. Process solutions proposed to deal with these issues are also indicated in the article. INTRODUCTIONDesign and construction of the processing plants involving High Pressure Grinding Rolls (HPGR) technology becomes more and more common in mining as this technology has specific technical and economic advantages against the circuits with autogenous/semiautogenous mills (AG/SAG) and other circuits. The main advantage of the technology is low energy consumption and low operation costs respectively. The presence of microcracks and increased content of fine size fractions in the crushed product contribute to reduction of energy required for further ball grinding. Besides, HPGR technology applies a special wear resistant liner that enables significant reduction of operation costs of grinding media and liner comparing with AG/SAG circuits."

Jan 1, 2016

By J. Palarski

In the Polish coal mining industry, the use of mine waste in underground backfill has been the most common means of providing ground support to minimize surface subsidence, increasing extraction ratios, and reducing the quantity of waste for surface disposal. Over the last decade attention has been focused on the use of different waste as filling material of underground workings and grouting of roof fall rocks in caving area. In the paper, a brief history of the development of fill technology in Polish coal mining industry is presented. Next, the paper discusses various criteria that should be taken under consideration in the preparation process of a fill slurry and grout, fill distribution systems, mining geometry and placement methods. Moreover, in the paper evaluation of the potential of utilizing coarse and fine waste as a resource material in the production of a backfill slurry and grout for filling and injection in abandoned mines is presented.

May 1, 2007

By Joseph A. Olmstead

Literature concerned with management and supervisory training was reviewed and analyzed from the perspective of relative effectiveness of various training methods for improving knowledge and awareness, changing attitudes, improving problem solving skills, improving interpersonal skills, and improving on-the-job performance. Conclusions were drawn relative to each method and the current state of the field of management and leadership training. A 168 item annotated bibliography is presented.

Jan 1, 1980