Search Documents

By William H. Walton, Joel Dellaria, Jeffrey R. Hill

The City of Chicago has a world-renowned skyline and is known for its provocative architecture. The subsurface conditions in the city have allowed for construction of these significant structures. The skyline is supported on caissons as they are called in Chicago or drilled shafts in other locations. Despite the significant strides the industry has made in advancing the drilled shaft, the use of other specialty geotechnical construction techniques like micropiles has not been overlooked in Chicago and the surrounding areas. Micropiles have been utilized to underpin famous existing historic structures like Orchestra Hall any many others. Engineers have used 200 to 600 kip micropiles to underpin compromised, inadequate, or damaged caissons. The paper will discuss the use of drilled shafts, micropiles, and ground improvement over the last 30 years in Chicago using a curated collection of case histories. It will also examine advancing the industry beyond its current technical limitations using these techniques. INTRODUCTION 20,000 years ago, glaciers from the Chicago region left behind sheets of glacial clay till underlain by dense, over consolidated glacial till below: limestone bedrock, found about 100 ft below street level. An unusual feature in this profile is the soft Chicago Blue Clay. Chicago has been called the birthplace of the Skyscraper and drilled shaft foundation, both of which came about in the 19th century. After the Great Fire of 1871, tall new structures were built rapidly and designing a successful foundation was trial and error. The first deep driven wood pile and caisson foundations bypassed the problem layer and found solid support on hardpan till or bedrock below (Schock and Risberg 2013). Once the drilled shaft foundation became acceptable to the Chicago engineering and construction community, building heights and complexity grew dramatically. As the city grew, building foundations were being repurposed. There was also the need to underpin structures for additional loads and shallow foundations for adjacent construction. Hand-dug drilled shafts were an option for some of these restricted access and low headroom sites but a new technique, micropiles, would prove to be the future of retrofit and hard to construct foundations. Micropiles were introduced on a limited basis to the United States market in the 1970s and 80s. In the early 1990s, the Chicago market began to latch onto micropiles and their use has grown significantly as a solution to the most complex foundation problems a maturing skyline has to offer.

Jan 1, 2019

By Xianyang Qiu, Xiuzhi Shi, Chen Xie, Xiaofeng Huo, Yanhai Wang

In upwards medium-deep hole cut blasting, many confinement effects exist due to the small number of free surfaces, which is mainly provided by an empty hole. If the cut blasting effect cannot meet expectations, then subsequent blasting construction will be seriously affected, and large security risks to operators in the stope can be induced. The number of free surfaces is directly related to the layout of the cutting borehole. Therefore, it is necessary to optimize the layout of the first round of cutting boreholes. Theoretical analysis, numerical simulations, and field tests were used to study the formation process of cut blasting and optimize the layout of the first round of cutting boreholes. Based on the blasting parameters in the field, LSDYNA software was used to establish cut blasting models with four kinds of borehole layouts in the first round. The RHT constitutive model was used to simulate the rock-breaking effect. The numerical results show that the cut blasting effect is optimal when Nos. 3, 5, 7, and 9 are charge holes and Nos. 1, 2, 4, 6, and 8 are empty holes. In addition, the greater the number of empty holes, the larger the release space and the better the cut blasting effect. The uniformity of the empty hole distribution, namely, the uniformity of the release space, also affects the cut blasting effect. The field results indicate that a good cut blasting effect can be achieved by optimizing the borehole layout.

Sep 7, 2023

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Donald E. Archibald, Gerald A. Allcott

"Noranda's Heath Steele Mine is located 35 miles north of Newcastle in northern New Brunswick. Blasthole open stoping with partial delayed filling is the major mining method in use. The selection of stope and pillar dimensions to ensure mine stability was originally subjective. This paper describes the progress made in attempting to rationalize design.One major feature is the fracture pattern. The main orebody now being mined, the B zone, has undergone five periods of folding and each period of folding developed a family of fracture planes which are axial planar to that particular fold pattern.The other major features considered are the calculated increase in stress due to mining and depth and its relationship to measured strain. Experience has shown that ground problems affecting production have usually originated in rib pillars. Field observations of ground deterioration and multi-wire extensometer measurements of strain are tabulated together chronologically for each pillar.A factor representing stress and a common plane of weakness are identified. Graphical analysis is used to determine the effect of the plane of weakness on a typical stress/strain curve and provides a base for the design of pillars."

Jan 1, 1981

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior of TiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was = 150 and that of the silica in the same system was = 0.02, resulting in a separation factor of = 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

By D. Brunner

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By R. E. Hamilton

It is more than ten years since the first fully automated process using a computer started operation. Computer control has become common in a number of process industries, yet in spite of the tremendous incentives which ere present, there are only a few computer installations in the mining industry and none of these has announced successful control of a process. Recognizing that one of the reasons for this slow progress is the lack of adequate mathematical models of the various processes involved, the author's company started a project in the summer of 1966 to develop such models. It was early recognized that the existence of a major disturbance input, in the form of the mineral composition of the feed prevents most flotation plants from attaining a steady state condition. This makes the custom¬ary method of developing correlations from steady state plant data inapplicable and requires a more fundamental approach.

Jan 1, 1968

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

Definir el concepto de exploración minera conlleva un estudio mucho más allá de las actividades minero-geológicas delimitadas por el cálculo de tonelaje del yacimiento. En este sentido, el objetivo del texto, señala una nueva noción, donde la exploración es un juego de azar caro en el que la extensión del yacimiento se mueve no solo en términos cuantitativos, sino que se invierte grandes capitales con un factor de riesgo. A pesar de esto, se continúa con la ejecución del proyecto, al tiempo que se evalua el apoyo del Estado, pequeños mineros, la Sociedad de Ingenieros del Perú, Instituto de Ingenieros del Perú, entre otros organismos interesados en lograr una economía promisora para la industria minera. Otro aspecto importante en su ejecución, son los factores económicos y costos de producción tales como el aumento de jornales y salarios, costo de materiales y métodos más complejos de exploración. En esta perspectiva, la exploración se convierte en una forma de investigación que no requiere una logística compleja para el nuevo producto, aunque el enigma de la certeza persiste. Así, se necesita buen criterio y experiencia para determinar la etapa de exploración en la que los trabajos adicionales no son justificados ni necesarios. Una vez determinada el área a explorar, se necesita la adquisición de los derechos mineros, para la exploración primaria y asi aplicar el levantamiento geológico de la zona, que fijará una tasación aproximada dentro del espacio explorado. Por último, el estudio revisa la eficacia de exploración de las minas de Cerro de Pasco, como en Oyón, Cuajone, Tintaya, Yarabamba y Antamina, concluyendo que es necesario el empleo de las nuevas técnicas de exploración minera que se practican en otros países a base de una mayor liberalidad del Servicio Aereofotográfico Nacional, asi como es urgente promover un inventario minero-histórico en los 1244 distritos que comprende el territorio peruano en sus 1'331,410 Kil6metros cuadrados.

Jul 20, 1959

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By D. R. Spink

An historical background is presented to provide a basis for the lack of normally expected developmental effort over the first 20-25 years of viable zirconium production operations. This is followed by a description of developing technology, which is the result of years of research and piloting effort directed to the development of a more economical method to produce high-grade metallic zirconium. It is predicted that many of the process improvements described will have a significant impact on future zirconium production methods and consequently on future prices and markets.

Jan 1, 1977

By Kenneth L. Norris

Stonegate Agricom Ltd. is currently conducting exploration and development drilling of the Paris Hills Phosphate Project (Paris Hills Project) located in Bear Lake County, southeastern Idaho, 3.2 km west of the towns of Paris and Bloomington, Idaho. The project is located adjacent to a highway and 19 km by paved highway to Montpelier, Idaho where the Union Pacific Railroad system is located. Power and water are available locally. The nearest metropolitan centre is Salt Lake City, Utah approximately 225 km by road to the south-west of the property. The Paris Hills Project encompasses an area of approximately 856 hectares. Property holdings consist of three (3) patented lode mining claims and 16 contiguous fee parcels (some with federal phosphate leases). Active open pit phosphate mining operations are located in surrounding counties in south-east Idaho and are owned and operated by Agrium Inc., Monsanto Company and J.R. Simplot Company. The Paris Hills Project is located near the centre of the Western Phosphate Field which constitutes the most extensive phosphorite beds in the United States. Phosphate beds of the Western Phosphate Field occur within the Phosphoria Formation of Permian age and extend over an area of more than 350,000 km2 including extensive areas of Idaho, Utah, Wyoming and Montana. At Paris Hills the phosphate mineralized beds occur in the overturned limb and the horizontal limb of the Paris Syncline. Grades and thicknesses in both the western overturned limb and the eastern horizontal limb of the anticline are similar. The vast majority of potential mineralization occurs in the horizontal limb which underlies most of the property holdings. Mineralization in the overturned limb has a strike length of over three (3) kilometres and extends from the surface to a depth exceeding 300 m depending on location along the north-trending strike of outcrops. Depths of the horizontal limb range from surface along the north side of Bloomington Canyon to estimated depths of 915 to 1,035 m at Paris Canyon. The property contains an Inferred resource of 109.6 million tonnes at 23.6% P2O5 over two mineralized horizons. The phosphate zones have a strike length of over 3 km and extend from surface to a depth of at least 900 m. Drilling commenced late in the 3rd quarter of 2010 and is planned to continue through 2011. The drilling was planned to target an area of potentially higher grade phosphate mineralization and better define and upgrade the current resources.

May 1, 2011

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By William W. Adams

The stone-quarrying industry of the United States, including such related operations as rock crushing, rock dressing, and the manufacture of cement and lime, reported a larger volume of employment in 1934 than in 1933. Reports from the operating companies to the United States Bureau of Mines showed an increase in the number of men employed, number of man-days of employment, and total number of man-hours of labor performed during the year. Moreover, the average worker had a longer period of employment during 1934, the gain amounting to 11 percent over 1933. The increase in employment was accompanied by no increase in accidents for the industry as a whole; in fact, the accident rate for 1934 was a fraction lower than the rate for 1933. In some branches of the industry the frequency of accidents increased, but these increases were more than offset by reductions in rates for other branches. Reports for 1934 were received from 1,403 active plants. The working force averaged 64,331 men for 204 days per man, and the total period of employment for all of the men was 95,258,880 man-hours. Each employee averaged 1,481 hours of work during the year. The total number of hours of labor represented a gain of more than 8 percent, and the average working time per employee showed a gain of 62 hours per man.

Jan 1, 1936

By Charles F. Jackson

Waste filling has been employed for many years for supporting the walls of stopes and preventing failure and subsidence of the surrounding and overlying rock formations, and its effectiveness for this purpose has long been recognized. It is used for permanent support in ground where timbering (including square-setting) is inadequate for more than temporarily supporting the walls of the excavations. It should be rioted, however, that effective as a good, solid fill may be in resisting heavy side pressure and direct weight, its usefulness for supporting large areas of back and preventing breaking and movement of the overlying rocks is limited. Even the strongest and most uniform rocks will break if the unsupported span becomes too great; and since filling cannot be packed tightly against a horizontal back there is always a possibility of the back breaking and consequent subsidence if the maximum self-supporting span is exceeded. Planes of separation, such as bedding and fault planes, slips, and joints, are common in all rock masses; these may occur above the stoping area where their presence cannot be ascertained by observation. If too much reliance is placed upon filling for the support of a large horizontal area of back (as contrasted to support of vertical or steeply inclined walls) large masses of rock may break along a. plane of weakness, compress the fill, and leave an open space into which caving of the overlying rocks may continue until the space is filled. In this paper the term "waste filling" includes any filling material other than ore - waste mine rock, rock from surface quarries or opencuts, sand and gravel, mill sands, or slags from smelting operations.

Jan 1, 1935

By Hori M, Komatsu T

In Japan, a small-diameter tunnel boring machine (TBM) of diameter 2.6 m applicable to a wide range of geology from hard rock to soft strata was developed with the purpose of reducing construction costs of headrace tunnels for small hydroelectric power stations. And in 1983, a demonstration test was carried out in the No. 1 headrace tunnel work of Hayakido Hydroelectric Power Station. The principal achievements in executing work are the following: (1) Although this TBM was a demonstration test unit, excavation advances averaged more than 200 m/month and exceeded the average 150 m/month with a conventional method. (2) According to PS velocity surveys after tunnel excavation the zone of loosening due to the TBM method was small enough to be ignored and was approximately one-half compared with conventional methods in rock of the same evaluation.

Jan 1, 1987

By Thomas A. Morgan

The distribution of stress adjacent to each of 25 mine openings was determined by the borehole stress-relief method in the FMC Corp. Westvaco trona mine at Westvaco, Wyo. The purpose of the stress determinations was twofold: First, to study the effect on these distributions of various factors such as opening shape, stress level, and loading history; and second, to estimate the distribution of stresses adjacent to extensive high-extraction (85 to 100 percent) areas. Stress distributions in areas of low average stress correspond closely to the theoretical distributions based on elastic theory. However, in areas of high average stress, the stress distributions are of a type associated with plastic failure. The stresses adjacent to a mined-out area supported by remnant pillars were significantly higher than the stresses adjacent to another area in which the remnant pillars were removed.

Jan 1, 1965

By Zhiqiang Zhou, Shengnan Zhou, Zizong Zhu, Yuchuan Ding

The effect of silicon on removal of phosphorus from high phosphorus Si–Mn alloy was investigated at 1673 K by CaO-based slag. It was found that the dephosphorization efficiency increases significantly as increasing the silicon content, which is due to the reaction between silicon and CaO at slag/alloy interface. The relation between silicon content with oxygen activity and phosphorus activity coefficient of Si–Mn melt was determined respectively as follows: lg aO = -1:55xSi - 1:67; ln rP = 9:26e xSi 0:0433 + 11:0839 The carbon content in Si–Mn melt decreases continuously with the increasing silicon content, meanwhile, the decreasing rate of carbon content becomes rapid when the mole fraction of silicon is about 0.32. Si addition is beneficial for both dephosphorization process and low carbon Si–Mn alloy production.

Mar 1, 2017

By J Zhou

Based on the mineralogical characteristics and mineral processing techniques required, gold ores can be classified into 12 types, including gold placers, quartz vein-lode ores, oxidized ores, silver-rich ores, iron oxide copper gold ores, porphyry copper gold ores, iron sulphide ores, arsenic sulphide ores, antimony sulphide ores, bismuth sulphide ores, telluride ores and carbonaceous sulphide ores. The bulk mineralogy and gold deportment of each ore type is different and may have a significant impact on ore processing and metal extraction. This paper summarizes the bulk mineralogy and gold deportment in some major types of gold ores and discusses the potential impact of gold deportment on gold metallurgy.

Jan 1, 2011