Search Documents

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By Andre Vien, Jean-François Dupont

"Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the installation and use of such a device on a SAG mill at the Holt-McDermott Mine. Comparison to measured static volumetric load and bearing pressure and inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed. INTRODUCTIONWhile the measurement of load is very important in all kinds of grinding applications, the biggest benefits are expected from AG and SAG milling. This is what motivated Holt-McDermott to take a closer look at this problem, with a view to optimizing SAG mill performance.In many cases, the SAG mill control problem can be stated as maximizing throughput while avoiding a volumetric overload, with the other constraints (e.g. power, grind size, upstream/downstream equipment constraints, etc.) playing a less important role. This is certainly true at Holt-McDermott where the SAG mill is the production bottleneck about 90% of the time, and anything that can be done to increase SAG mill throughput will have a significant impact on operating profit.Although the goal of maximizing throughput while avoiding volumetric overload is simple to state, it has proven to be much more difficult to achieve. The mineral processing industry has expended a great deal of time and effort to devise control strategies in the pursuit of this objective. While much progress has been made, there is still room for considerable improvement. Across the industry it is probably fair to say that overloads occur relatively infrequently, but the real losses accrue as a result of the tendency to run rather conservatively."

Jan 1, 2001

Newmont Waihi Operations is participating in the initiation of a community liaison forum in association with the local district council. The objective is to provide a forum for the free and regular exchange of ideas, concerns and information, and through improved communication seek to achieve a more comprehensive set of solutions to community, operating and closure issues associated with Martha Mine. A similar liaison forum has been operated on two previous occasions during earlier phases of the present mine's operation. This paper deals with the practical aspects of setting up a liaison forum to act as an effective conduit between regulators, mine operators, local businesses and the community. The mechanisms and procedures for identifying community issues and concerns are dealt with. The actions and structures required to ensure effective ongoing community 'buy in' at all levels are discussed. Corporate philosophies are addressed. Specific examples from Martha Mine, Waihi New Zealand will be used to illustrate the paper. This will include a brief explanation of previous and current community issues, Newmont Waihi's operations both at Martha Mine and the proposed Favona underground mine, and the practical issues involved in setting up a liaison forum.

Jan 1, 2003

By Charlie Adcock, Rob Farnfield, Andy Wetherelt

The ISEE Blasters Handbook gives guidance on the level of air overpressure likely to cause occasional window breakage (151dB) and general window breakage (171dB). A long-term safe level of 140dB is also suggested. This guidance is widely used by demolition and other contractors to assess damage zones in the region of explosive applications employing unconfined charges. Other reference material gives more detailed guidance relating to window area, aspect ratio and glass thickness. Despite the guidance given in these references, complaints by members of the public regarding window breakage continue to be received by explosives engineers from air overpressure levels well below the longterm safe limit. Such complaints are not limited to the use of unconfined charges but can even be generated from the highly confined use of explosives in quarry blasting. This paper describes a series of experiments with explosive charges fired in unconfined conditions close to various window configurations. The aim of the work was to test the existing guidance levels and to extend the knowledge base in this area. Topics covered include the role of differential pressure across windows in the walls of an enclosed space such as a room.

Jan 1, 2006

By R. D. Leitch

"INTRODUCTION The character of mine drainage from areas of low pyritic coal3 and from average pyritic coal4 has been investigated, and to complete the study it seemed desirable to select a number of mines situated in high pyritic are as to determine whether or not this variation determines the relative acidity of drainage from mines operating in these characteristic coal fields. Advantage has been taken of some worked on in 1918 by Henry Leighton 5, then Professor of Economic Geology, University of Pittsburgh. He visited and has reported certain areas of high pyritic coal which we also visited during this study. Many of the mines were found to be idle in 1930 and a few were caved shut, apparently for several years. However, samples of the outflow from all mines visited were collected if possible and analyzed, and some general information was gathered for each mine. The map (fig. 1) shows the location of these areas as given by Leighton.ACKNOWLEDGMENTSThe information and assistance obtained from officials and others at the mines visited during this study are gratefully acknowledged, as well as the original suggestion from Dr. Glenn V. Brown of the State Sanitary Water Board who called attention to the desirability of such a study.Thanks are also especially due the coal laboratory of the United States Bureau of Mines, under the direction of H. M. Cooper, for the analyses and determination of sulphur forms in the large number of solid samples necessary to the work reported,This study has been carried on under the direction of R. R. Sayers, chief, health and safety branch, and W. P. Yant, supervising engineer, Pittsburgh Experiment Station, of the U. S. Bureau of Mines."

Jan 1, 1932

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

In his account of the Thackaringa sulphide ore, Lawrence (p. 92) reports the presence of valleriite as a minor accessory in chalcopyrite. He says that it is readily identified by its intensive anisotrophy and reflection pleochroism. He also gives (p. 87) the chemical formula as Cu8Fe4S7 Recent work by Evans et al. (1964), Chamberlain and Delabio (1965), and Schidlowski and Otteman (1966) suggests that most material identified as valleriite is, in fact, mackinawite. Mackinawite and valleriite are both extremely anisotropic and strongly reflection pleochroic, and so with fine-grained material it would be hard to distinguish them optically.Mackinawite, according to Evans et al. (p. D66) is a copper-free iron sulphide (PeS) with small quantities of nickel, whereas valleriite is considered to be a dimorph of chalcopyrite (CuPeS2 ). They found that mackinawite is much more widespread than valleriite, and, unlike the latter mineral, is commonly included in other sulphides, particularly chalcopyrite.Lawrence (p. 92) states that the valleriite inclusions are up to 0·01 mm long, so that an electron probe microanalysis should be quite feasible and provide a ready answer to this query.L. J. Lawrence: I thank Dr Townend for his comments on the occurrence of a valleriite-like mineral embedded in chalcopyrite from Thackaringa. The problem of distinguishing valleriite from mackina...

Jan 1, 1967

By William H. Schiffbauer

This report details a microcomputer-based control and monitoring network that was developed in-house by the U.S. Bureau of Mines and installed on a continuous mining machine. The network consists of microcomputers that are connected together via a single twisted-pair cable. Each microcomputer was developed to provide a particular function in the control process. Machine-mounted microcomputers, in conjunction with the appropriate sensors, provide closed-loop control of the machine, navigation, and environmental monitoring. Off-the-machine microcomputers provide remote control of the machine, sensor status, and a connection to the network so that external computers can access network data and control the continuous mining machine. Because of the network's generic structure, it can be installed on most mining machines.

Jan 1, 1993

By G Baiden

The removal of rock blockages in mining operations has long been a risky undertaking, especially in high overhead conditions. Moreover, the assessment of where to put charges and the placement of them has been difficult due to the lack of visibility and safe access to the area. Traditionally, wedging long poles with explosives on them to keep the operator at a relatively safe distance has been the tried and true method of attempting to remove the blockages. Unfortunately, this is not a perfect system as it usually takes several attempts to remove the blockage. Each successive attempt results in even more dangerous conditions for workers and/or damage to the mine due to the successively larger amounts of explosives used until the hang-up finally comes down.Over the years, different ideas have been proposed to improve this process and reduce the inherent safety risks. Some of the technologies that have been trialled include projectiles fired at the hang-up; large, cumbersome arms; and massive amounts of explosives, each of which come with their own inherent safety risks that result in dangerous situations for miners and the mine.After gaining a thorough understanding of the process, Penguin Automated Systems Inc has developed a robotic system that is capable of working in a rock blockage safely. The idea combines the latest in telerobotics technology with 3D scanning and underground geospatial positioning. The hang-up removal is performed by scanning the inside of the hang-up to rapidly develop a geospatially placed 3D model for the operator to use. The 3D model is detailed enough that the operator can attempt to pick the ‘keystone’. A blasting engineer or the operator can then determine the exact position where the explosive charge should be placed in the 3D model and thus at the actual hang-up. The operator, controlling the robotic arm, uses the 3D virtual reality model of the robot system and the actual drawpoint information model to display the location information, the arm can then reach into the hang-up to position the charge using the kinematic model of the robot system. The 3D model is used to provide views inside the hang-up so that the operator can move the arm safely and precisely. This process allows the operator to place the charge (using the 3D representation of the drawpoint) from a long distance away. As the process continues, the end of the arm drills the rock and precisely loads the explosives. The robot then returns the blasting cable to the command station, which is located in a truck at a safe distance from the blockage.This paper will review the development of the system and present the results to date.CITATION:Baiden, G, 2016. Robotic hang-up assessment and removal of rock blockages in mining operations using virtual reality for safety, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 745–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S. E. Phillipson

The Mine Safety and Health Administration?s (MSHA) Roof Control Division (RCD) collects a variety of geological and engineering information pertaining to mining conditions in surface and underground mines throughout the United States. Recently, lineament analyses, trends of geologic structures, and inferred stress directions based on mapping at mines with problematic ground conditions, have been integrated into a GIS. The incorporation of different kinds of information into the same geographic coordinates and map projection, placed on digital geologic maps, allows site specific data to be evaluated in a regional geospatial context, identifying trends in the orientation of horizontal stress or patterns of structural geologic features. As more information is collected, the GIS will evolve as a tool for district- and basin-wide evaluations of controls on ground instability, and may evolve into a predictive tool for some kinds of geologic hazards. In addition to the geologic and geotechnical evaluations, the GIS also serves as a searchable database of previous mine investigations. The database can be searched for a variety of criteria, and the results displayed in real geographic coordinates to find the locations of previously visited mines or to evaluate mine fatality and injury data. This not only allows old reports to be found, but also places the information in a geospatial context with respect to neighboring mines or geographic areas. The GIS also has the capability to serve as a digital mine map repository, where maps can be stored in digital, georeferenced format for display in relation to each other and various themes of interest. This allows evaluation of multiple seam mining interactions and proximity to other mines, and on a national level could serve as an abandoned mine map database.

Jan 1, 2008

By Iván E, Alex Araya Jofre, Jean Guiroux Toro, Eduardo Valdés Guerra

Currently, it is important for companies to have controlled mining operations and adhere to production schedules. To achieve this, one of the key factors is maintaining high reliability in the P&T process, primarily the opening of ore stope, which could be delayed due to any unplanned or uncontrolled problem. These ore stope opening processes, whose main activity is generating free face, are a very important pillar for future mine planning. The possibility of ensuring their opening brings a series of downstream benefits: safety, economics, productivity, and compliance and adherence to plans. The process under discussion consists of developing free faces in a single blasting event. This will help us leverage greater reliability for overall production operation plans, reduce construction times, and open up opportunities for downstream improvements in the production process, considering technical factors in P&T designs. This study presents a developed methodology and shows the results of its implementation in ten (18) single-event free face blasts. The analysis includes cavity geometry, geology, rock qualities, drilling deviations, and the blasting strategy implemented for each event. The methodology used considered material fluffing processes, the actual drilling trajectory, the initiation sequence, QA/QC during explosive loading, monitoring instrumentation (vibrations), and VOD recording, among others. As a result, out of a total of 18 free-face events blasts in a single event, 16 were successful and two achieved 90% efficiency, reducing the stope's production start-up time by 50% compared to current operations. By implementing free face blasting in a single event, there are savings in operating costs, increased productivity of the mining equipment, and improved adherence to production plans. For applications with greater heights of free faces, where blasting cannot be carried out in a single event, we should consider performing them in two stages using wireless detonators already available on the market for mining operations.

Jan 26, 2026

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By D. R. Torgoson, Th. G. Sahama

"This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2siO4 and MgSiO3-FeSiO3 and gives the results of a thermodynamic attack on the problems of stability end parageneses.. Although some data are lacking satisfactory agreement with mineralogical and petrological observations is indicated.The use of thermodynamic methods in mineralogy and petrology has been rather limited, because accurate thermal data, especially for the more complicated and more important rock-forming minerals, have been too scanty to permit any systematic application to problems in those fields. It is, nevertheless, a fascinating task to investigate to what extent the mode of occurrence and the stability relations of the minerals and mineral parageneses, as revealed by petrological and mineralogical observations, agree with predictions of thermodynamics. At the present stage of development calorimetric data are needed for most of the abundant silicate minerals.Measurement of the heats of solution in hydrofluoric acid of minerals in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 affords a ready means of obtaining their heats of formation from the oxides. Combination of such data with entropy and heat-capacity values gives a means of obtaining free energies of formation from the oxides, which, in turn, are connected di¬rectly with stability and paragenoses.The two silicates of magnesium, Mg2SiO4 and MgSi03, occur as rock-forming constituents as forsterite and clinoenstatite or enstatite. The orthosilicate (forsterite) forms a series of isomorphic mixtures with ferrous-orthosilicate (fayalite). The continuity of this series, suggested by petrological observations, has boon proved experimentally by Bowon and Shairer.4/ The present work shows that those minerals constitute a series of perfect solid solutions - that is, a series of solid solutions for which heats of formation from the individual pure silicates, Mg2Si04 and Fe2SiO4, aro negligibly small.The metasilicates of magnesium and iron also form an isomorphic series. However, this series differs from the forstorito-fayalite series in the fact that the most iron-rich mixtures, between about En10Fs90 and pure Fs, appear to be unstable with respect to the paragenesis iron-rich olivine plus quartz. The supposed instability of pure FeSiO3 as a crystalline compound, at least at high and at moderate temperatures, is remarkable, as no crystal struc¬tural reason for such instability is apparent. The present work indicates, also, that these minerals form a perfect series of solid solutions and throws additional light on the instability question.In the following, the samples used in this investigation will be described. For each of the natural olivines and orthopyroxenes, with the exception of sample L, a chemical analysis was made of the purified and actually used fraction. All the analytical work was carried cut by Oleg v. Knorring, and the specific gravity determinations, by moans of a pycnomctcr, by Oiva Joensuu, both of the University of Helsinki, Finland. The determinations of the optical properties were made by Mrs. Toini Mikkola, of the Geological Survey of Finland."

Feb 1, 1949

By A Hollweg, K H. Esbensen, M Lischka

Two new splitter designs for intercepting moving streams of matter are presented, the variable cross-stream splitter (vCSS) and the rotary stream splitter (RSS), which are intended for implementation in a fully automated modus. The vCSS facilitates obtaining up to three subsamples with different splitting ratios from automated laboratory flow paths, while the RSS divides the intercepted sample into 16 equal analytical aliquots. The splitters can process a wide range of dry, granular and free-flowing materials (<5 mm). The required weight for each subsample can be set without mechanical adjustments in the case of the vCSS. Typical applications are subsampling/splitting for X-ray fluorescence pelletisation (or fused beads) or splitting for average shift composite sampling or grain size analysis. The vCSS combines the advantages of riffle splitting (three user-defined subsample masses) with miniature bed blending and can accept up to 15 kg in total incoming sample mass. In practice, the automated vCSS can deal with unlimited ingoing mass fluxes, while the RSS is designed to operate at a user-defined fixed subsampling rate (1/16th in the tested version). Both splitters have the potential to be optimised and evaluated according to an application/user-defined total sampling error (TSE) + total analytical error (TAE) threshold. Both splitters were tested under adverse conditions and with compositions involving three components with properties representing typical mass fluxes and components concentrations in industrial and technological systems: phosphate concentrate 89.00 per cent (<500 µm), slag ten per cent (>2 mm) and glass spheres one per cent (750–1000 µm). The slag particles vary widely in particle shape, aspect ratio and surface roughness, while the glass spheres are extremely prone to bouncing and segregation (spillage). This test system is extremely difficult to split and thus constitutes a realistic worst-case scenario. While the vCSS does not comply strictly with Theory of Sampling demands for correctness, both splitters may well be able to deliver fit-for-purpose representative results if/when tested properly. Average relative mass deviations ranged from 1.89 per cent for phosphate concentrate (relative standard deviations of 20-fold repeated splitting) to 4.72 per cent for glass spheres and 13.04 per cent for slag. For the RSS, the average replication experiment splitting variation was 2.89 per cent for phosphate concentrate, 4.82 per cent for glass spheres and 11.1 per cent for slag. Both new automated online splitters would therefore appear to be able to be tuned to fit-for-purpose representivity (defined here as maximum relative reproducibility <5 per cent) for many non-extreme materials; however, it is always imperative to test every new type/class of material empirically. There is a wide commercial potential for important materials and commodities sectors, including food, feed, drugs (pharmaceutical), secondary raw materials, recyclates, agricultural products and seeds.CITATION:Lischka, M, Hollweg, A and Esbensen, K H, 2017. New online/atline splitter designs for laboratory automation – feasibility results, in Proceedings Eighth World Conference on Sampling and Blending , pp 159–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

GENTLEMEN, lt is with much pleasure I meet you tonight at this the second meeting of the Australasian Institute of Mining Engineers, held in Western Australia, and I sincerely thank you for the honour you have conferred upon me in electing me as your President. I greatly appreciate the distinction, and will endeavour to fulfil the duties of the office to the best of my ability, and hope to prove a worthy successor to those gentlemen who have held the position before me. On behalf of the local members of the Institute, I extend a hearty welcome to the members from the other States of the Commonwealth, who have come so far to attend this meeting, and also to the non-members whom we have invited this evening. We are especially pleased to have Mr. Gregory, our Minister of Mines and Railways, and the Government and School of Mines officials with us; and I take this opportunity to thank the Premier, Mr. Gregory, and the Government officials for the assistance given us, and for doing so much to make the visit of our members from the other States so pleasant and instructive. I have also to thank the Mayor and Councillors of Kalgoorlie for the courtesy and hospitality given to our members, which is much appreciated.I assume you want me to follow the time-honoured custom of giving a Presidential address...

Jan 1, 1909

By R S. Hamilton, S R. Grobler, M E. Greenway

The progressive development of underground mines frequently requires increased ventilation flow rates through mine shafts that were originally designed for lower rates. Where these shafts are equipped with conveyances running on rope guides, the higher air flow rates adversely affect the lateral motion of conveyances and could cause conveyances to collide with the shaft walls or with one another. Hence the safety impact of higher flow rates requires proper assessment. This can be undertaken by use of computer simulation models to predict the dynamic motion of the conveyances during hoisting. It can also be undertaken entirely by field testing, or using a combination of simulation and field testing. This paper discusses these techniques and makes cautionary remarks about setting an absolute generic maximum flow velocity for all shafts. Approaches to assess existing shafts for increased ventilation flow rates are also discussed.CITATION:Greenway, M E, Grobler, S R and Hamilton, R S, 2017. Safety impact of increased shaft ventilation on rope guided conveyances, in Proceedings Australian Mine Vent Conference 2017, pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

The following observations on the mineral composition of the lead-zinc ores at Captain's Flat, New South Wales, are based upon the examination of a collection of specimens made during a brief visit to the mine in January, 1942, in conjunction with earlier studies of specimens and mill products, which have 'been the subject of various Mineragraphic Reports, Captain's Flat is about 35 miles south of Canberra, and is connected with the main line from Goulburn to Bombala by a branch line to Bungendore, 23 miles away from the mine.The geology of the mine has been described by Kenny and Mulholland2 and by Harper.3 The country consists of Silurian sediments, which have been invaded by a composite sill of quartz-felspar-porphyry. Both sediments and sill have been folded gently, the axial lines of the folds trending north and south. In the vicinity of the orebodies the folds are steeper, and thru,st faults are associated with the anticlines. The intense compression and shearing that accompanied the faulting has converted the adjacent porphyry to schist. The Captain's Flat orebodies occur along such a zone of shearing and faulting, on the eastern limb of a steep, north-pitching anticline. At their southern end the orebodies are enclosed in the slates underlying the porphyry, but the northerly pitch of the fold carries the slate to greater depth in the northern part of the mine, where the orebody lies beween schistose porphyry on the hanging wall and massive porphyry in the footwall.THE OREBODIESThe orebodies occur along a N.-S. strike length of 4,200 ft., and from the point of view of mining, fall into three sections: the Elliot's Section to the north, the Central Section, and the Keating's Section to the south. The Keating's Section is separated from the Central Section by 500-600 ft. of mineralised ground of so low a grade as' to be called barren, and is offset about 125 ft. to the 'east of the Central body by an oblique fault striking N.300E. Elliot's Section and the Central Section are connected by persistent veins and stringers of lead-zinc ore, but although these are...

Jan 1, 1943

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \'r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or' ?. ~eries deGcribi 1{) t:;'~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,'Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper 'Ii 11 be i acuss d c .icilY rub"col'-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"'e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941