Search Documents

By M. R. Haibach, M. L. Shema, J. M. Silvis

"Since 2005, longwall coal mine operators in Pennsylvania (US) have been required to collect extensive hydrologic and biological data to document pre- and post-mining conditions of aquatic resources (streams and wetlands) overlying the subsidence control plan areas. Continued operation of the longwall mine is dependent upon empirical data demonstrating that the undermined aquatic resources have either been maintained or restored to an accepted range of pre-mining conditions. This study used quantitative hydrologic methods and comparative biological metrics to examine response of aquatic resources to longwall subsidence at the Bailey Mine located in Greene County, Pennsylvania. This study analyzed data from over 25 miles of streams and over 8 acres of wetlands that traverse the 4,779-acre study area. Hydrologic analysis of flow intermittency suggested that there are variable degrees of change to headwater streams immediately following mining; however, the majority of the effects are reversible through streamflow mitigation measures. Furthermore, the post-mining discharge from streams can be restored to within the range of pre-mining conditions the majority of the time. Biological assessments showed that greater than 95% of assessed stream length has maintained its ability to support benthic macroinvertebrate communities following mining and intervention (i.e., mitigation). Comparative metrics of the benthic macroinvertebrate communities showed that the biological community in 48 of the 50 sample sites is being maintained or restored across both high- and low-gradient streams. The effectiveness of intervention was further substantiated by the similarity in recovery times between streams having no intervention (median = 2.1 years, 95th percentile = 4.9 years) and streams with intervention, when recovery times were measured from the date of the intervention (median = 1.7 years, 95th percentile = 4.7 years). Changes to individual wetlands were observed between the pre- and post-mining assessments, but cumulatively a net gain of 7% in wetland acreage was realized. Hydrologic assessments were used to infer whether there was a potential that streams had been affected by mining; however, the ultimate test of stream recovery is based on biological metrics that establish the relative quality of the biological communities following mining. Overall, the hydrologic balance is being protected and the aquatic life use of streams is being maintained within the Bailey Mine’s subsidence control plan areas."

Jan 1, 2017

By D. P. Tao, J. G. Groppo, R. Killmeyer, W. W. Wen, B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 ~ 25 m) clean coal slurry produced by the `Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 165o cake formation angle, provided a filter cake with 23.6percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of `orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Frank B. Fulkerson

Barge traffic on the Nation's inland waterways over the past 15 years has been increasing at a rate much faster than intercity freight traffic by all modes, largely due to the growing consumption of mineral commodities, development of more powerful towboats and large and more specialized barges, improvements to loading and unloading facilities, and competition among bargelines for contract shipment of bulk commodities. The Bureau of Mines, in a study to determine barge traffic projections for inland waterways in the South-Central States to the year 1980, gathered data on origin-destination patterns by commodity, quantity moved, equipment used, and rates charged; the trend of each of these factors over time; and the extent of competition between water trans-port and other means of transportation. The Mississippi River and the Gulf Intracoastal Waterway, which together carryover half the Nation's barge traffic, are major carriers of coal, crude petroleum, steel, marine shells, sulfur, salt, cement, and alumina. Greater quantities of these products will be transported by barge; however, oil pipe-lines and unit trains for coal are expected to limit increased barge traffic of these two commodities. Increasing quantities of fertilizer materials will be transported upstream. Although congestion at certain locks is a current problem, the Mississippi River below St. Louis and other open-river stretches have the capacity to handle the increasing number of barges for the foreseeable future.

Jan 1, 1969

Safe operation and system integrity are two important properties of a mine hoist electrical system. Previous methods used to assess these systems, though rare, have involved extensive downtime and required skilled personnel. The recommended design considerations presented in this report are for a proposed automated system that will perform real time measurements, calculations, and recordings of pertinent performance data. Included are equipment installation and test procedures to be used with the system. The report also contains descriptions of the hoist performance criteria, and how they are to be collected.

Jan 1, 1985

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By R. R. Wells, G. M. Potter, R. Havens, W. W. Agey

"INTRODUCTION As part of the program of investigating possible domestic sources of manganese, ore-dressing studies were conducted at Salt Lake City, Utah, on five samples of manganese oxide ore obtained by mining engineers of the Bureau of Mines from the Havasu Lake District, California and Arizona.Two lots of radically different ores were procured from the Arizona Manganese claims 30 miles above Parker Dam, Mohave County, Ariz. One of the original 11 claims has been flooded by Havasu Lake, formed by Parker Dam. The claims are owned by R. H. Thompson, Parker Lumber Co., Parker, Ariz. The 2-ton lot of high-grade ""TA"" ore represented ore occurring as pyrolusite and psilomelane accompanied by a black calcite gangue in lenses along a series of fault planes in granite. A half-ton lot of low-grade ""TB"" ore was taken from a large lense of reddish iron-bearing material outcropping on another section of the property.A 2-ton lot of ore was taken from the Jones property, 8-1/2 miles southwest of Powell, Mohave County, Ariz. At the time of the investigation, the property was leased by J. H. Jones, of Oatman, Arix., from the owners, the Atchison, Topeka, & Santa Fe Railroad Co. The ore body was described as a re¬placement in a sandstone formation in a region that has been faulted extensively."

Dec 1, 1947

By A. L. Toenges, F. A. Jones, J. N. Sxudder, E. R. Maize

"INTRODUCTION This report is the second of a series of studies of analysis of energy requirements and characteristics of various machines used in the production of coal in underground mines and the losses in distribution of energy to these machines. The test equipment used in these studies is described in Report of Investigations 3615. 7/ The preliminary study data and results of tests made on various types of mechanical-leading cutting, and transporting equipment at two mines. This report is analysis of the energy requirements of the energy requirements of the underground equipment of a third mine. An analysis of the use of energy and its distribution usually requires in a saving in energy consumption and the reduction of hazards. The distribution system should be designed to supply energy effectively and study for the efficient operation of all machines."

Feb 1, 1943

By R. H. Church, William E. Webb, Walter E. Pittman, James R. Boyle

As part of the Bureau of Mines health and safety research program, a short-range locator system, capable of locating miners who have become trapped following a mine accident, has been devised, The system consists of a lightweight, low-power radio transmitter incorporated into a miner's cap lamp battery and a directional receiver carried by rescuers. Prototype transmitters have been constructed, and the propagation of their signals has been investigated, The detectability of the signal in underground coal mines has also been investigated, This research indicates that a short-range location system would serve as an economical and practical means of locating miners from within the mine following an accident,

Jan 1, 1984

By David L. Hill

Newmont Gold Company's Mill No. 4 is located along the Carlin trend, about 25 miles North of Carlin, Nevada. The plant consists of a primary grinding circuit using a 7.2 m (22 ft) diameter by 2.6 m (8 ft) long semi-autogenous mill along with a 2.3 m (7 ft) diameter cone crusher. Secondary grinding is performed in a 4.8 m (14.5 ft) diameter by 9.2 m (28 ft) long overflow ball mill in closed circuit with a set of 66 cm (26 in) diameter cyclones. The ground product is fed to a typical carbon-in-leach gold leach circuit. The grinding/crushing circuit operation and control scheme are the topics of this paper.

Jan 1, 1993

By C. H. Riggs

This report of a petroleum-engineering study of the Flat Rock oil field, Osage County, Okla., describes the geology, reviews the production history, and estimates remaining oil reserves. The Flat Rock field in the southeastern corner of Osage County approximately 6 miles northwest of Tulsa. Okla., was discovered in November 1904. The field was one of the first of many Bartlesville-sand fields developed in eastern Osage County during the early part of the 20th century. Although substantial oil reserves remain in the pressure depleted sands in some parts of the field, their economic recovery by water flooding will require careful consideration of the many factors involved.

Jan 1, 1954

By D. R. Rathburn

Jan 1, 1962

By L. C. Brichta

The Canyon Diggings zinc-lead deposit is in an area of structural deformation of sedimentary rooks in Newton County, Mo., 14 miles southeast of Joplin, within the southern limits of the Tri-State district. Mining and milling on the several tracts covering the area had been carried on sporadically since 1900, and incomplete records show a production of 1,341 tonsof zinc and lead concentrates. On the northern part of the deposit the predominant metal is which occurs as galena, cerrusite, and pyromorphite in broken chert near the surface. On the southern part, lead is subordinate to zinc, which occurs mainly as carbonate and silicate minerals in brecciated chert to a maximum depth of about 150 feet. Analyses of samples from Bureau of Mines drilling indicate that approximately 77 percent of the zinc and 50 percent of trio lead i8 in nonsulfide minerals resulting from the oxidation of sphalerite and galena. Between August 12, 1948, and October 5, 1949, the Bureau of Mines investigated the deposit by churn drilling and sampling 85 holes aggregating 10,571 feet of bore and sampling two mill-tailings dumps and three mine dumps. Factual data on the investigation and the logs of Bureau of Mines drill holes are presented in this report.

Jan 1, 1950

By AIME AIME

A THOROUGHLY satisfactory crowd turned out at the fall meeting of the Industrial Minerals Division and took an active part in the entire program. On Thursday afternoon, Sept. 24, a limestone plant was inspected, technical sessions occupying the attention of the visitors all day Friday and Saturday morning. Headquarters were at the Nittany Lion Inn, an attractive hostel on the Penn State campus, at State College, right in the center of Pennsylvania. We are still in the dark, despite inquiries, as to just what breed of lions Nittany lions are. As nearly as we could find out, Nittany is not a Biblical name, as it sounded to us, but a corruption of the name of an Indian princess, or maiden, or maybe just girl that haunted those parts in bygone times and after whom a near-by mountain was named. Penn State athletes are "lions" and there you are. The meeting was supposed to be a joint one with the American Ceramic Society's Materials and Equipment Division; but it was quite evident that the Institute had a much better publicity agent than the Society, which bothered Ross. Purdy, the aggressive secretary of the ceramic people, no end. However, Secretary Purdy saw to it that everyone present fully understood that the Ceramic Society was present, so that that contingent all but stole the show, its representatives presiding at every meeting. The Pittsburgh Section of the American Ceramic Society was also supposed to be holding its fall meeting there at the same time, but made no trouble at all for anybody, as one of the speakers remarked.

Jan 1, 1936

By John Hall

SOME months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter lie had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908; and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel.

Jan 9, 1919

By George L. Richert

The Minas de Matahambre is situated on the north coast of Cuba, in the Province of Pinar del Rio, approximately 150 miles west of Havana. This nine is the only producer of copper in Cuba, and has been worked for the past 15 years. In 1921 the property was affiliated with The American Metal Co., Ltd., and has been worked by them since that time under the direction of Mr. D. D. Homer, General Manager. Extracts from P. D. Wilson's ?Preliminary report on the geology at Minas de Matahambre? have been freely used in this report.

Jan 1, 1929

By B. P. Sullivan

This paper describes how the author projected the economic benefits of a proposed coal liquefaction project based in Pennsylvania. These benefits were assessed in a successful effort to garner government support for the project. The projections considered such issues as increases in employment, wages, and tax receipts to state and local government, plus other less-obvious benefits, such as site remediation. The paper explains how sponsors of similar projects can use economic projections in making meaningful and compelling presentations to federal, state and local authorities.

Jan 1, 2000

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By M. Onifade, B. Genc, P. O. Akinseye, M. Fourie, K. O. Said

Coal is mined by both surface and underground methods and its extraction is normally characterized by numerous hazards that can lead to catastrophic accidents, which result in devastating effects such as injuries or fatalities, damage to mining assets, and destruction of mineral resources. These hazards exist due to the ability of coal to support combustion and its association with toxic, flammable, and explosive gases. Underground coal mining entails higher safety risks than opencast coal mining, chiefly because of issues relating to mine ventilation and mine collapse. Furthermore, coal mine collapses mostly occur due to crumbling of mining supports, especially in room and pillar mining systems. To avoid such adverse occurrences, safety management systems need to be in place. This study reviews the various technological safety systems and principles that are used for safe-rescue and self-escape of miners in underground coal fires, particularly in South Africa, using data obtained from Mines Rescue Services in Carltonville, South Africa. The outcome of the review shows that practising safety culture has been given priority across many South African underground coal mines through setting up safety management systems and encouraging workers to stay committed to safety principles.

May 2, 2022

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

With a growing concern over mine fires, prevention and suppression are hot topics. NIOSH researchers Michael Trevits, Alex Smith and Edward Thimons discuss their research in the area. The leading causes of US mine fires include flame cutting and, welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions and spontaneous combustion. From 1990 through 2007, there were 1601 reportable fires that occurred in the US mining industry -an average of 89 fires per year. The fact that mine fires are occurring with alarming regularity reinforces the importance of recognizing and eliminating the potential hazards. These statistics also show the need for improved control and suppression technology to ensure worker health and safety if a mine fire does occur.

Jan 1, 2008