Search Documents

By C. E. M. Meskers

Electronic and Electric Equipment contains a range of components made of a wide variation of metals, plastics and other substances. Up to 60 elements can be found in complex electronic equipment: base metals, precious metals and special metals in circuit boards and batteries. Because of its amount WEEE represents a considerable metal resource with a higher special and precious metal content than found in ores. The Umicore integrated smelter and refinery recovers and supplies back to the market 17 different metals from EEE. Pre-treated materials enter state of the art, material and energy efficient metallurgical processes for environmentally sound recovery of metals and treatment of off gasses and hazardous substances. The organics in the feed function as reducing agent and alternative energy source during smelting for precious metal recovery. Lithium-ion batteries are treated using a dedicated process. As a result the environmental footprint of metals produced from EEE is much smaller than primary production.

Jan 1, 2009

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and pulp-zone bubble size (Db) in full-scale flotation systems. To obtain conclusive evidence exclusively related to the pulp (collection) zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that Db had a significantly larger effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of coarse particles was close to zero, but dramatically increased by reducing Db. The evidence revealed an inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb (i.e., the rate of production of bubble surface area) did not always result in higher recovery, as the model predicts. Furthermore, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only in the presence of suboptimal-sized bubbles (Db > 2 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, the role of the froth was negligible for Db < 1 mm.High-resolution mineralogical measurements performed on process samples revealed that, regardless of the degree of liberation, Db had a profound effect on the shape of the recovery-by-size curve, particularly the coarse particle size fraction. This observation is key as it implies that the loss in efficiency associated with floating the coarse particles was not the result of neither particle hydrophobicity nor particle detachment issues: even in the absence of mechanical agitation, liberated and highly hydrophobic coarse particles did not seem to attach to the bubbles in the first place, an inefficiency that was corrected by reducing bubble size. The data analysis suggests that poor attachment efficiency can practically affect both fine and coarse particles but via different mechanisms which are discussed here."

Jan 1, 2017

By R A. M Maddever, P Jeanneau, V Flahaut

Over the entire life cycle of a mine, from early resource evaluation to the blasting of benches, the collection of geochemical data is crucial for the site operator, who must routinely and intensively drill and sample the orebody. This produces huge numbers of physical samples, in turn requiring significant cost and time for their preparation and assay. Moreover, despite best efforts, the sample recovery process is prone to error, which limits the quality of data.The pulsed neutron gamma technique has been used for decades in various industries, in particular oil logging, for its ability to provide direct identification and quantification of elemental concentrations. However, its implementation in logging tools for the mining sector is relatively recent. Built around the latest in technology for optimal spectrometric measurement, a commercial tool referred to as FastGrade™ 100 has been available for a few years and used with increasing success in the mining environment, specifically the iron ore industry, resulting in a reduction in the amount of collected samples. Relying on the physics of neutrons and gamma photons, both of which are particles that penetrate the surrounding bedrock through several tens of centimetres, such spectroscopy tools measure in real-time the composition of a much larger volume than the delimited volume of the drilled material traditionally used for geochemical mapping. Better statistics and reliability of the estimated composition increase the ability to properly and quickly measure drilled holes and allow the substituting of all or part of the sampling and assaying efforts by geochemical log data. Our paper focuses on this technology, known as pulsed fast and thermal neutron analysis (PFTNA). It reviews the main drivers for the design of such a logging tool and discusses how the fundamental characteristics of the technology, in terms of neutrons and gamma interactions, translate into interpretation of the analytical output.CITATION:Jeanneau, P, Flahaut, V and Maddever, R A M, 2017. Iron ore benefits from neutron pulsed geochemical tools, in Proceedings Iron Ore 2017, pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. J. McLeod, D. R. Lux, R. P. Taylor

"The Mount Douglas Granite constitutes the eastern part of the Saint George Batholith and contains the youngest, most differentiated phases of the batholith. It also contains extensive endogranitic, low-grade. Sn- W-Mo-bearing sheeted vein systems. Early phases of the Mount Douglas Granite are coarse- to medium-grained, seriate granites that represent the slowly cooled carapace of the intrusion. Late phases are medium- to fine-grained, equigranular and porphyritic granites that were accompanied by repeated and widespread fracturing of the carapace and injection of mineralizing fluids. These granites represent a highly differentiated suite with ""A "" type affinities developed in a ""within plate"" transitional to ""syn-collision"" tectonic setting. 4oAr/ 39Ar dates for biotites from the various phases indicate emplacement circa 367 Ma.The linear distribution of some phases in the Mount Douglas Granite and the systematic orientations of sheeted veins along tensional fractures indicate structural control on granite emplacement and vein distribution. This type of relatively passive endogranitic mineralization is unique in the granites of southern New Brunswick and contrasts markedly with highly fluidized systems operative elsewhere in the area. IntroductionInvestigation of Sn-W-Mo occurrences in New Brunswick has shown that most of this mineralization is associated with late, highly differentiated phases of post-orogenic (Acadian) granitoid magmatism that occurred during Devonian and Early Carboniferous time (Ruitenberg and Fyffe, 1982; Taylor et al., 1988). The polymetallic Mount Pleasant Sn-W-Mo deposit (Ruitenberg, 1967, 1972; Kooiman et al., 1986)and the Burnt Hill W deposit are two orebodies of this type in New Brunswick. Numerous smaller deposits associated with these granitoid rocks in southwestern New Brunswick have been documented in previous investigations (Ruitenberg, 1967, 1968; Ruitenberg and Fyffe, 1982; Taylor et al., 1985; Lentz, 1985)."

Jan 1, 1988

By J. -F. Lessard

Most underground mines rely on ore pass systems to ensure the transport of ore and waste. The design and operation of ore pass systems often rely on past experience, which is often anecdotal and at times contradictory in nature. This paper summarizes the current practice in Quebec underground metaliferous mines. The information was collected during a series of site visits in ten underground mines. The database includes information on ore pass configuration, support, materials transited, and overall ore pass performance.

Jan 1, 2006

By Bowen Li

Silicon Carbide is an excellent refractory material. Its physical properties make it extremely useful, particularly in applications where corrosion resistance and wear are important considerations. Commercial silicon carbide refractory is frequently manufactured by bonding silicon carbide particles with clay; however, clay may cause problems in the sintered products. This study investigates the potential of replacing a portion of the clay with andalusite powder. The results show that micron size andalusite powder can improve not only the strength of the refractory but also the sinterability. The mechanisms for these improvements are discussed.

Jan 1, 2006

By J Charbucinski

Commonwealth Scientific and Industrial Research Organisation (CSIRO), Exploration and Mining, has developed nuclear spectrometric techniques for borehole logging. The paper reviews the latest developments of this technology for the metalliferous mining industries. The SIROLOG logging system developed by CSIRO Exploration and Mining has been commercialised and is available to the mining industry.

Jan 1, 2000

By Gaby Steinbach

A novel synthesis is described for the preparation of supported gold catalysts for low-temperature CO oxidation. The novel route is a variation of the inverse co-precipitation method and requires amphoteric metal hydroxides, with zinc and aluminium hydroxides chosen. Catalysts were prepared by inverse co-precipitation (ICPa) and by the novel route (ICPb) and tested for CO oxidation at 60ºC. Preliminary results showed the novel route to be superior to ICPa; the catalysts prepared by ICPb showed higher catalytic activities. The effect on catalytic activity of parameters such as pH, calcination temperature, washing of precursor and calcined catalysts and ageing was investigated. A preparation pH of 9 and a Zn to Al mass ratio of 3 proved to be optimal. It was possible to remove residual chloride by washing thereby enhancing catalyst performance. Ageing and Mg citrate addition were also shown to improve catalyst performance. Characterization of the catalysts revealed that better activities were obtained when the support was more crystalline and had a higher surface area. The presence of carbonate-containing species in the support decreased catalytic activity. 197Au Mössbauer Spectroscopy revealed the presence of Au3+ when catalysts were heat-treated at temperatures of 200ºC and below. Catalysts calcined at 400º had 75% of the gold present as Au0, with the remaining gold present as Au3+.

Oct 1, 2003

By Les A. Beckett

The Bureau of Mines has developed MULSIM/BM, an improved computer program using the boundary-element approach for geomechanical analysis of mine plans in single or multiple coal seams. This Information Circular presents the improved features of the MULSIN/BM program. The four major improvements are the following: (1) Ability to specify up to 26 material property sets. (2) A new material model capability for gob and inserted materials such as packwalls or cribs. (3) Ability to model a large area with a grid of undivided blocks and to subdivide only a specified fine-mesh portion of these blocks into elements. (4) Specification of extraction ratios for the undivided blocks. In addition, an interactive graphics mesh generator program was written to accompany MULSIM/BM. A complete user&apos;s guide and program listings are included within the appendixes. The MULSIM/BM and mesh generator programs are available on tape from the National Technical Information Service.3

Jan 1, 1988

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms&apos;s method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

By R. A. Bosch, F. V. Lenel, G. S. Ansell

RECENTLY, Ansell and aenel&apos; proposed a dislocation model to account for the yielding behavior of dispersion-strengthened alloys. The criterion for yielding used in this model was that yielding occurs when the shear stress due to arrays of piled-up dislocations fractures or plastically deforms the dispersed second-phase particles. Calculations based on this model predict that the yield strength, uysof a dispersion-strengthened alloy containing particles whose geometry permits them to be considered as straight, i.e. not curved, barriers to dislocations follows the relation where and are the shear moduli of the matrix and dispersed phase respectively, b is the Burger vector of a dislocation in the matrix, A is the mean free path between dispersed phase particles and C is a constant. This yield stress, ys, is closely approximated in polycrystalline alloys by the proportional limit. The offset yield stress, uoy, is the yield stress, uys, plus the increase of stress due to strain hardening in the offset strain increment. Previous investigation1 has shown that Eq. [I] describes the yielding behavior of several different dispersion-strengthened alloys as a function of the mean free path between dispersed phase particles at a constant temperature. The purpose of this investigation was to investigate the temperature dependence of the yielding behavior of dispersion-strengthened alloys. The alloys studied, MD2100 and MD5100, are SAP-type alloys containing flake shaped aluminum oxide particles dispersed in a matrix of commercial purity aluminum. The proportional limit and 0.2 pct offset stress of both of these alloys were determined as a function of temperature over the temperature range from -190" to 500 C. All tests were conducted on an Instron tensile testing machine. Stress was measured by means of the Instron load cell. Strain was measured by means of SR-4 strain gages attached to the tensile specimens. Stress sensitivity was 80 psi. Strain sensitivity was 2 x 10F Fig. 1 shows the values received for the proportional limit and 0.2 pct offset yield stress plotted as a function of homologous temperature for both the MD2100 and MD5100 alloys. Inspection of Eq. [I] shows that of the terms which determine the theoretically predicted yield stress, uy,, only the shear moduli have an appreciable temperature dependence. From Eq. [I] the yield stress at any temperature T, UT, may be predicted from the yield stress at any arbitrary reference temperature, in this case 25 OC, u25, by the relation where the subscripts T and 25 refer to the values of the property at test temperature and at 25"C, respectively. The temperature dependence of the yield stress predicted by Eq. 121, based on the observed value for the proportional limit at 25OC, is also shown in Fig. 1. In evaluating Eq. [2] the following data was used. The values for the shear modulus of

Jan 1, 1962

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

By Pathies Nawej Muteb, Tom Strombotne, Karl Leetmaa, Irma Gabric, Keith Darby

"Continuous control of the final grinding product size is important to optimize gold liberation for Gold Milling operations. At Meadowbank Mine an on-line Particle Size Monitor has been employed successfully to achieve the targeted final grind which leads to optimizing the gold recovery at maximum grinding circuit throughput. The live monitoring of the final product particle size leads to a maximum grinding circuit throughput every minute during the process. This paper discusses the optimal utilization of the Particle Size Monitor to assist the Mill operator to maximize the grinding circuit throughput as the milling conditions change due to variable ore processed at Meadowbank Mine. Also the paper includes the usage of the Particle Size Monitor to guarantee the final grind target at each instant of the process.IntroductionAgnico-Eagle is a Canadian-based company that Trades on the TSX & NYSE (AEM). It owns eight mines (8) operating in Nunavut, Quebec, Finland and Mexico and has more than 7,500 employees (Figure 1). 1.6 M ounces of gold were produced in 2015 and the annual average annual production from 2016 to 2018 is forecast to be approximately 1.53 million ounces of gold.The Meadowbank Mine is located in Nunavut, Canada (Figure 2). The mine opened in 2010 and from 2010 to 2014 a total of 1.8M oz of gold was produced. The milling rate is 4.2 Mt per year with an average mill throughput of 11,900 tpd or 496 tph. Average annual gold production over life of mine is expected to be 450,000 ounces. Meadowbank has 775 employees, of which 265 are Inuit or 36% of the total workforce. Estimated life of mine is 2010 to 2018. Gold production in 2015 was 381,804 oz. Meadowbank was Agnico-Eagle’s largest Gold producer in 2015."

Jan 1, 2017

By S. Panigrahi

The SO2-ammoniacal ammonium sulfate leach liquor generated by leaching of manganese nodules, after removal of minor quantities of iron and manganese, contained copper, nickel, cobalt, zinc and (NH4)2SO4. After extraction of copper from the leach liquor with LIX 84I, stripping of ammonia from the Cu-barren raffinate was carried out followed by precipitation of metal ions from the ammonia-stripped solution as sulfides. Leaching of the sulfide precipitate was carried out with H2SO4 to obtain a leach liquor containing 0.58 kg/m3 Cu, 2.67 kg/m3 Zn, 2.00 kg/m3 Co, 24.68 kg/m3 Ni and 10.0 kg/m3 (NH4)2SO4. After extraction of copper and zinc from the sulfate leach liquor with LIX 84I and D2EHPA, respectively, the solution was left with Co and Ni. Extraction of cobalt from the Cu- and Zn-free solution was carried out with 0.1 M PC88A and stripping of the cobalt-loaded organic was carried out with the cobalt-spent electrolyte (pH 1.4). Extraction of nickel from the cobalt-free solution was carried out with 90% neutral 1M NaPC88A followed by stripping of the nickel-loaded organic with 120 kg/m3 H2SO4 solution. Extraction of metal ions increased with increasing equilibrium pH and extractant concentration. The maximum separation factors, with respect to the pH and extractant concentration variation studies, were 3796.7 and 15350.0, respectively. The extracted species for the metal ions were CoA2?3HA and NiA2?5HA.

Jan 1, 2009

By R Kroukamp

Horizontal belt filters are typically used for separation of relatively free filtering solids where good post treatment is required. He horizontal belt filter is a continuous filter with an endless cloth supported on a grooved carrier belt. The belt and cloth are driven around two rollers across a series of evacuated suction boxes. The feed suspension is introduced at one end of the filter and deliquored to produce a cake at the other end. The benefits of using horizontal belt filters are good cake washing, continuous and visible processing, fully automatic operation, flexibility, high capacity and relative high speeds of operation. If required, horizontal belt filters enable efficient counter-current washings to minimize the usage of wash liquid. The horizontal belt filter has applications in the following: [? Metal concentrates ? Mineral sands ? Tailings ? Coal ? Iron ore ? Alumina ? Chloride processing ? Nickel and Cobalt refining ? Platinum group metals ? Zinc processing ? Many other applications in the Mining and Metallurgy industries ] 2. Operating Principle of a Horizontal Vacuum Belt Filter 2.1 Cake Forming The slurry to be dewatered is evenly distributed onto the filtering surface. Gravity assists the cake formation and the feed can be introduced in multiple stages. 2.2 Cake Washing Once the cake is formed, wash liquor/water can be introduced onto the top of the cake via a wash launder or sprays. Multiple wash stages, co-current, counter-current or direct washing can be added by increasing the length of the filter.

Jan 1, 2007

By Murat Alkan

In this study, a self-propagating high-temperature synthesis (SHS) and following acid leaching techniques were carried out to produce boron carbide (B4C) powder. First, B2O3 was obtained through calcinations of H3BO3 at 1073 K for 2 hours. Then, the glassy B2O3 obtained was crushed and sieved. In the SHS experiments, different amounts of B2O3, Mg and C black were used. The SHS product was obtained in the form of black, spongy solid. In the leaching step, the SHS product was leached in a HCl solution to eliminate the MgO and Mg3B2O6. The effect of acid concentration on the selective leaching was studied at different concentration range, solid/liquid (S/L) ratio, and temperature. The products obtained were characterized by using X-ray diffraction, chemical analysis and SEM techniques.

Jan 1, 2009

By Adil Aledresse, N. Emre Altun, Bern Klein, Nuri Hmidi, Brent Hilscher

A study was conducted to investigate high gold grades in water lines and carbon fines collected from the Musselwhite gold recovery circuit. It was discovered that fine magnetic particles in the overflow from the carbon fines settling tank launder had high gold grades ranging from 2,000 to7,000 g/t. The -37 micron fraction had up to 17,000 g/t gold. Scanning electron microscopy revealed the gold was attached to the surface of iron particles. The objective of the study was to identify possible mechanisms that result in the attachment of the gold to the magnetic iron particle surface and to recommend process modifications that would reduce these types of gold losses around the carbon circuits. Solid and solution samples were collected from the gold recovery circuit and analysed. Two possible mechanisms were identified including gold cementation onto iron and heterocoagulation of colloidal gold onto iron oxides in the elution column. Possible sources of the colloidal gold include reduction of gold cyanide complex to metallic gold in the carbon regeneration kiln and gold detached from cathode in EW cell. Based on SEM+EDX, the sources of iron were natural magnetite and roasted iron sulphides. Thermal reduction of gold is believed to be the cause of dendritic gold from the carbon regeneration kiln.

Jan 1, 2014

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite.

Jan 1, 1916