Search Documents

By Y Cai, B Hebblewhite

In this paper, the Australian thick coal seam underground mining potential is highlighted and the characteristics are investigated by analysing a thick seam database. It is clear that thick coal seam resources should be mined with a high recovery, productive, efficient as well as a safe and reliable mining method. Longwall Top-Coal Caving (LTCC) is the most recent thick coal seam mining method which has been developed and extensively used in China for the last ten years. The successful applications indicate that this method has a very high recovery and productivity rate and less development cost in comparison with any other thick coal seam mining method. One of the aims of the current study is to seek potential for the application of LTCC as a thick seam mining method in Australia. In this paper, preliminary results of investigation on Australian thickseam potential are given and results of data analysis for potential LTCC seams in Australia are described. The outcome of this study shows a great promise for the application of LTCC in Australian coal industry.

Jan 1, 2002

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By Ben Aleck

The objective of this program was to adapt Space Shuttle technology on high-performance spherical pressure vessels to cylindrical pressure vessels. Specifically, a cylindrical aluminum liner overwrapped with fiberglass filaments and prestressed by yielding the liner under a sizing pressure was to be replaced by a higher strength-to-weight ratio steel liner overwrapped with a higher strength-to-weight ratio filament. The steel was cryoworked stainless steel and the new fiber was Kevlar 49. In addition, the heavyweight ends of the aluminum liner were to be replaced by thin-walled domes which required multiple helix angle wraps for their support, in place of the single kite-string wrap from pole to pole of the aluminum overwrapped design. The use of cold swaging of tube-ends to form bosses, demonstrated on subscale development efforts, had not been achieved full-scale when the contract was initiated. Difficulties arose with the full-scale demonstration which were not solvable at the time with the designs and equipment available. hence, an unanticipated development was the finally selected method of making the 4-in.-diameter stainless steel liner with a single boss and no welds in an 0.020-in.-thick wall, from an 0.050-in.-thick, 13-in.-diameter disk. The demonstration vessel failed by leakage during the prestressing step because embedded oxides had formed flaws in the boss region. Such flaws have been avoided by proper temperature control during hot spinning. Hence, a new design was developed which weighs half as much as its recently developed predecessor. Funds ran out before adequate testable hardware was produced.

Jan 1, 1983

As longwall shields are lowered in preparation for advance, dust from the canopy falls directly into the air stream with the potential of becoming entrained. Historical dust sampling data from the early 1980s shows that shield advance contributed an average of 12 percent to the airborne respirable dust levels found on longwalls in the United States. Data from the 1990s indicates that shield dust liberation had increased to an average of 23 percent. Increased longwall production levels over this time resulted in the need to move a larger number of shields during each shift, while an increase in air velocities on the face was also occurring. These factors combine to suggest that greater quantities of shield dust are being entrained into the face air. A series of controlled laboratory tests were conducted in a test stand simulating shield dust entrainment to evaluate changes in airborne respirable dust levels at different air velocities. Significant differences in respirable dust entrainment were observed. The test facility, test methodology, and dust sampling results will be reviewed and discussed

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

By Onuralp Yücel, Süheyla Aydin, Erçin Ersundu

Turkish iron and steel sector, the base of which was established in the 1930?s, plays an important role in the industrialization and development of the country?s economy. In Türkiye this sector is the major consumer of ferroalloys. There had been a great improvement in Turkish Iron and Steel industry, especially after the 1980?sand as a result, 20.9 million tons of yearly crude steel production placed Türkiye 11th in the global steel output and 3rd in Europe. 15 % of steel produced in Türkiye is flat products, while the long products make the rest. The product composition and the general characteristics of steel production process led to an increase in ferroalloy consumption. Domestically consumed ferroalloys are especially ferromanganese, silicomanganese, and ferrosilicon. As of today, ferroalloy production capacity of Türkiye is 173,800 tons/year; 161,500 tons of which is ferrochrome with high and low carbon grades, 7,300 tons of ferrosilicochrome and the rest is ferrosilicon (5,000 tons/year). Türkiye is one of leading ferrochrome producers in the world considering the above mentioned production figures. However, this production is mainly exported since Türkiye?s stainless steel production level is modest requiring low amounts of ferrochrome. The products of iron and steel industry in Türkiye require large quantities of other ferroalloys, which make Türkiye a major importer and exporter of ferroalloys. The aim of this work is to present production, consumption, import and export quantities of: ferrochrome, ferromanganese, ferrosilicon, ferromolybdenum, ferrotungsten, ferrotitanium and ferrovanadium of Türkiye, between 1990 and 2006.

Jan 1, 2007

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

By Beth Robinson

This first of two articles on the Second Mexican Mining Rail Excursion describes some of the more casual experiences participants enjoyed on last fall’s rail tour of major Mexican mining operations. In this article, Beth Robinson, a graduate student at Colorado School of Mines, describes trip organizers, participants, and some of the unique events occurring during the two-week excursion. Next month, part two of the series will highlight various Mexican mines and plants.

Jan 1, 1982

By D. Fukahori, K. Sugawara, A. Sato

X-ray Computed Tomography (CT) is a nondestructive imaging technique, and its efficiency is widely recognized. In the present paper, X-ray CT is successfully applied for the visualization of water permeation process in rock. A new experimental technique using a tracer, which mainly consists of Potassium Iodide (KI), is proposed, together with the analysis method of the velocity field. The permeation process and the velocity field in rock are concretely visualized and analyzed by considering the conservation of mass of the tracers. La tomographie calculée aux rayons X est une technique de la prise d'images non-destructive et son efficacité est largement reconnue. Dans le présent exposé, la tomographie calculée aux rayons X Radio est appliquée avec succès à la visualisation du procédé de perméation de l'eau dans la roche. Une nouvelle technique expérimentale, se servant d'un identificateur principalement constitué d'iodure de potassium (KI), est proposée avec la méthode de l'analyse du champ des vitesse. Le procédé de perméation et le champ des vitesse dans la roche sont visualisés concrètement et analysés en considérant la conservation de masse des identificateurs. Röntgen-Computer-Tomografie (CT) ist eine nicht-destruktive Bildverarbeitungstechnik, deren Effizienz weit anerkannt ist. In der vorliegenden Arbeit wird Röntgen-CT erfolgreich für die visuelle Darstellung des Wasser-Durchdringungsvorgangs im Fels eingesetzt. Eine neue experimentelle Technit mit einem Tracer, der hauptsächlich aus Kaliumiodid (KI) besteht, wird vorgeschlagen, zusammen mit der Analysemethode des Geschwindigkeitsfelds. Der Durchdringungsprozess und das Geschwindigkeitsfeld im Fels werden konkret visualisiert und analysiert, wobei die Bewahrung der Masse des Tracers berücksichtigt wird.

Jan 1, 2003

Komatsu America has introduced its 2-MW (2,700-hp), 930E-3 ac electric drive truck with a 290-t(320-st) capacity. The truck is designed to provide increased productivity, lower cost per ton hauled and improved speed and control. The 930E-3 is powered by a Komatsu SSDA16Vl6016-cylinder engine. It is capable of speeds up to 65 km/h(40 mph) and is a 15-percent to 20-percent more productive unit than 218-t (240-st) trucks, at a lower operating cost per ton. The 930E-3 also provides enough torque and speed to get up and off ramps easier than mechanically driven trucks. And it can climb at altitudes up to 3,650 m(12,000 ft) without any fuel deration.

Jan 1, 2004

By D Craw

Oceana Gold as part of their environmental strategy are looking at various methods for cost-effective revegetation of their tailings dams. Under the concept of revegetating the tailings this study looked at several issues. These issues were; testing different methods of revegetation, arsenic (As) uptake in vegetation with respect to capping thickness, and background As levels in farmland areas above mineralised rocks. A number of plots were set up in a temporarily disused tailings dam to trial the direct sowing of ryecorn into the tailings.   Ryecorn was sown in sandy tailings (ca 1000 mg/kg As) and then covered with oxidised schist to anchor the seeds. This proved successful and ryecorn was established. Once the plots covered with oxidised schist were growing, 1 m and 2 m strips were sown on the sheltered side of the existing plots without the covering of oxidised schist. The uncovered plots also established successfully. From this set of trials a sowing plan can be developed that uses a minimum of resources to successfully establish vegetation. The maximum As content of the ryecorn was 80 mg/kg. Clover, Yorkshire fog and ryegrass plant matter was sampled from a pot trial that used different thicknesses of topsoil covering tailings material. As the thickness of topsoil increased, the amount of As taken up decreased. Soil samples were taken from farmland areas which were known to have elevated levels of As (up to 1000 mg/kg) in the top 10 cm. Vegetation samples were also taken from the same locations, and show the As levels in plants is <50 mg/kg.

Jan 1, 2006

By Raymond M. Stateham

Infrared and displacement studies were made of an unsupported roof in Kaiser Steel Corp.'s York Canyon coal mine, Raton, N. Mex. Monitoring of the roof continued until the roof over the area was caved. Loose slabs in the roof, about 6 inches thick, were detected by means of associated thermal anomalies, using remote-sensing infrared instruments. Displacement measurements taken during the study indicate that roof movement was cyclic in nature; the cycles appear to have been related to the mine work cycle (work days to idle days).

Jan 1, 1974

By Paul Downing

When was the last time the documents and paperwork were cleaned out of the glove boxes, door pockets, under the seats and above the visors in your company vehicles? Insurance cards that expired three years ago and vehicle registrations from 1999 through 2003, for instance, don’t do any good and just take up space

Jan 1, 2008

By S. Ripke

Between 2002 and 2004, the performance of a six million ton per year iron ore beneficiation plant dropped significantly. In a classic case of “who done it,” was it the mine, the concentrator, an ore change, or something else? While average annual final product grade decreased 8% (indicated by an increase in silicate gangue from 2.76% to 2.99%), the weight recovery also decreased by 8% (from 37.92% to 34.79%). This represents a loss of 832,000 tons of iron ore worth about $16 million for the two year period! The concentrator had been optimized to produce a high grade wet concentrate as feed to the dry side of the plant. But, did optimizing an individual unit operation’s grade give the best overall plant performance? In this paper, the investigation and solution to this mystery will be revealed.

Jan 1, 2007

By Kristine M. Krajnak

Occupational exposure to hand-arm vibration through the use of powered hand tools can result in reductions in tactile sensitivity, grip strength and manual dexterity. In fact, even acute exposures to vibration cause shifts in vibrotactile thresholds in exposed fingers (2,4,5). Although reductions in tactile sensitivity after acute vibration exposures are transient, cellular changes associated with this shift in sensitivity could lead to the more permanent reductions in tactile sensitivity that are a common symptom of hand-arm vibration syndrome (HAVS). Methods Animals. Male Sprague Dawley rats (6 weeks of age) were used for all experiments. Animals were housed in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guideline for care and use of laboratory animals. Vibration exposures were performed by restraining rats in a Broome-style restrainer, and securing their tails to the vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control animals were treated in an identical manner except that the tail platform was set on isolation blocks instead of a shaker. Tail temperature and current perception thresholds (CPTs). Rats were exposed to 4 h of tail vibration (125 Hz, 49 m/s2), or restraint. Tail temperature was collected prior to and immediately following the exposure using an infra-red camera. Sensory neuron function was assessed by measuring CPTs with a Neurometer (Neurotron, Baltimore, MD). Transcutaneous nerve stimulation was applied to the C10 region of the tail. Three frequencies were used to test specific fiber types (5 Hz – C, 250 Hz - Ad, and 2000 Hz – Aß). The intensity of the stimulus was automatically increased in small increments until the rat flicked its tail. Tests at each frequency were repeated until the animals displayed 2 responses that were within 2 CPT (or 0.02 mA) of each other (2-4 tests/animal). CPT tests were performed prior to the exposure, immediately following the exposure, and 24 h after the exposure. Data Analyses. Temperatures were analyzed using a one-way ANOVA with animal as a random variable. ANCOVAS were used to analyze the CPTs at each frequency. Temperature at the time of the CPT test was used as a covariate, and animal was used as a random variable Results Tail temperatures declined between pre and post exposure (F(1,25) = 62.85, p < 0.001; mean ± sem pre 25.96°C ± 0.42, post 20.71°C ± 0.77), but were back to baseline levels by 24 h after the exposure in both groups of rats. The ANCOVAs demonstrated that exposure to a single bout of vibration did not alter sensitivity of C (5Hz) or Ad (250 Hz) fibers to stimulation.

Jan 6, 2006

By W. F. Watts

This report describes the Mine Inspection Data Analysis System (MIDAS) developed by the Bureau of Mines to analyze the records of industrial hygiene samples collected by the Mine Safety and Health Administration (MSHA) in metal and nonmetal mines. MIDAS is the first system capable of sorting, editing, analyzing, and reporting these data. It is also the first system designed to be used by a number of Government agencies. At present the system contains 225,000 personal and area samples for 61 contaminants in 45 industries. The records date from 1974 to early 1980, and MSHA plans to provide yearly updates to the system. This report presents preliminary analyses of dust exposures and discusses the potential uses and limitations of these data. Analysis of the dust data for 1978 and 1979 showed that bagging had the highest percentage of dust overexposure. Morn than 40 pct of the 1,536 respirable quartz dust, total nuisance dust, and total silica dust samples exceeded the MSHA exposure limit. Other dusty occupations are ranked according to their percentage of overexposure.

Jan 1, 1981

By H. Forster, F. H. Koenemann, U. Knittel

The greenstone belt developed along the Sandawana line, an anastomosing, transcrustal shear zone. The lode gold is concentrated in veins and along brittle-ductile shear zones and other faults. Gold contents of 200 rock samples were found to be well below economically significant levels, excluding purely syngenetic deposit formation. Average gold content of unmineralised banded iron formation decreases from 7.3 ppb in the east (Manica) to 1.6 ppb in the west (Odzi), where depletion reflects hydrothermal leaching. The mineralising fluids may have been generated during deep crustal deformation, metamorphism and magmatism. Gold was hydrothermally deposited during carbonatisation and sericitisation of ultramafic and mafic rocks and during hydrothermal overprinting of banded iron formation and felsic rocks. It is present in native form and as microscopic to submicroscopic inclusions in pyrite, arsenopyrite and pyrrhotite. Argentiferous galena and other sulphides are commonly observed. Rezende, which produced over 38 t Au, is hosted by a granodiorite stock. By-product gold was produced from Cu-Ni sulphides at Mundonguara. The deposits are related to the older, but not the younger, of the granitoids intruding the belt's supracrustal sequences; the estimated age of mineralisation is 2700-2600 Ma. Odzi district, with 61 mines, has produced only 3.5 t Au as its higher-level host rocks have apparently been eroded. Mutare (formerly Umtali) district, with 133 mines and 9 placers, has produced 68 t Au (65 t from Rezende and adjacent deposits), and Manica district, with 23 mines and 8 placers, 12 t Au. Estimated reserves for the Rezende area are 20 t Au and for Manica district 4 t lode Au and 19 t placer Au

Apr 1, 1996

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the last decade. Accidents rates are improving but more slowly and yet, serious accidents and fatality rates are not: in fact, these rates of more serious incidents have plateaued or deteriorating. In more dramatic cases, organizations that had ?exemplary? safety statistics, suddenly had a catastrophic or multi-fatality event occurring. Popular books such as In Search of Excellence of Peters and Waterman or Good to Great of Jim Collins created many delusional ?secrets? or recipes, to achieve great performance and yet, most of those ?great? or ?excellent? companies have now declined in their performance, some dramatically and some have fallen from grace, like Fanny Mae, a company Jim Collins identified as a ?great? one, that had to be bailed out in the latest financial crisis. These organizations share several ?delusions? about managing a business, and often, these delusions are created by academics, consultants and authors of popular books about (safety) management. More damaging however is that safety management is defined by a set of key practices or axioms: a focus on human error, compliance to rules and regulations, creating consistency of systems and actions, reacting to accidents and incidents and on prevention of those, measuring safety with performance metrics and rewarding employees on those measurements. All of these axioms contain the seeds of destruction, and they create conditions and dynamics that precede the disaster - and ironically, they are all &apos;good things&apos; we do in safety management. For example, a mere focus on safety in the business, and the measurement of it, create a culture of repression of mistakes and incidents, leading to a situation where the organization knows incrementally less and less of risks and risktaking behaviour - until the day it all coincides destructively! This paper discusses seven such safety delusions and how they impact on the views and safety management approaches. They are: ??The delusion of (risk) control, that risks can actually be identified, analyzed and mitigated. ??The delusion of compliance, that mere compliance to rules will safeguard the business ??The delusion of consistency, that standard operating procedures will ensure safe operations ??The delusion of predictability, that accidents and trends tell us everything about the risks of the future ??The delusion of human error, that people are the weakest link and that it can actually be dealt with through discipline and enforcement. ??The delusion of statistical trends, that safety is measurable with statistics ??The delusion of invulnerability, that we have achieved high levels integrity and capability to deal wit risks. Organizations that suffered catastrophes all share some or all of these delusions and this paper traces how these played a role in many disasters, ranging from the Titanic, Challenger, Piper Alpha, Bhopal, BP Deepwater Horizon and many more.

Aug 1, 2013

By J. C. Willett, J. R. Sanfilipo, P. D. Warwick

The U.S. Geological Survey has conducted an assessment of the Nation’s coal deposits that potentially could be mined during the next 30 or more years. For the Gulf Coastal Plain region, the assessment includes reviews of the stratigraphy, coal quality and resources, and coalbed methane potential of the Cretaceous, Paleocene, and Eocene coal deposits in the region. The results of these efforts are a series of digital maps, text, and tables published in CD-ROM format. Although abundant coal resources are available in the Gulf Coast region, coal quality issues may limit large-scale development in the future. Additional data are required to better evaluate the coalbed methane resource potential for the Gulf Coast region.

Jan 1, 2001

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009