Search Documents

By Tom Treleaven

Several nonelectric blast initiation systems have been developed since the mid 1970's. Until that time, most blasts were initiated either electrically with electric blasting caps or nonelectrically with detonating cord. What the development of these new systems was attempting to accomplish was to provide a system that was nondisruptive to the stemming or explosive column, but still possessed the safety and flexibility inherent in nonelectric systems.

Jan 1, 1991

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

The following pages discuss the objectives, the background, and scope of work of an industrial engineering analysis of far-,n haulage systems in underground retreat coal mining. This study ran concurrently with an existing industrial engineering study of methods of improving safety and production efficiency in underground pillar extraction. 1. OBJECTIVES The objective of this project was to provide basic data inputs that will inpart knowledge as to the major constraint to pillar extraction sections. Furthermore, the industrial engineering study will suggest ways to optimize haulage systems and to develop more efficient work practices and operational techniques that will maximize equipment utilization.

Jan 1, 1975

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By A. El-Midany

Dolomite impurities are increasing in the currently mined phosphate deposits in Florida. Several research efforts have been conducted in various laboratories around the globe to find methods to economically removing the dolomite. However, a universal and cost-effective process is not now in commercial use. In this paper, a new process for dolomite/apatite separation is presented. The differential solubility of dolomite in slightly acidic solution is utilized to generate micro CO2 bubbles at the dolomite/water interface. Particle (dolomite)/bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro-bubble/particle aggregates. Different surface-active agents were tested to stabilize the bubbles. Results of these tests are presented, and the mechanisms involved are discussed.

Jan 1, 2009

In mining industries, materials loading and handling costs represent a significant component of the total (capital and operation) costs. A variety of methods have been applied in surface mine equipment selection in order to select the suitable loading and haulage system with the lowest total cost. The optimal size and number of equipment calculation are very important task for mining engineering because loading and haulage equipment are major proportion of open pit mining cost. Capital and operating cost are considered in objective function with respect to interest rate, insurance and tax in non-linear form. Shovel and truck annual productivity constraint, fleet matching constraint and number of truck per shovel constraint are incorporated in this optimisation problem with continuous variables. This formulation will yield total cost minimisation per hour and good accuracy compared to previous methods.

Dec 6, 2010

By M. Syamujulu

In 1994, Nkana smelter commissioned a multimillion US Dollar Chilean Teniente converter (CT) in its operations in order to improve its smelting technological base. The main objective was to reduce the overall smelting energy costs and increase the sulphur capture for sulphuric acid production to support the company?s leaching operations at Nchanga tailings leach plant. A decade of CT operations have since ensued following its installation and start-up. This paper provides a technical and operational audit of the performance of the CT in the first 10 years of its operations at Nkana smelter.

Jan 1, 2005

Thirty years ago a party of American Engineers, with members of their families, belonging to the four national engineering societies, sailed for Europe and visited England and the Paris Exposition of 1889 and received many courtesies, official, professional, and individual. Plans: have been made for a reunion dinner to be held in New York City, about May 26, at which it is hoped that all survivors, ladies as well as men, of that trip may meet again. It is, therefore, urgently requested that anyone who was of that party communicate immediately with the Secretary of the Committee, Jesse M. Smith, Engineers' Club, 32 West 40th St., New York, N. Y. Announcement of the precise date and place, and full details, will he sent to every individual who can he reached.

Jan 5, 1919

By S. Tanaka

The Tamano Smelter of Hibi Kyodo Smelting Co. Ltd. was commissioned in 1972. Since start up, the anode production capacity has increased from 101,000 tpy to 290,000 tpy, as a result of the application of continuous improvements at each phase of the expansion projects. The Tamano Smelter had developed several innovations, including the original coke combustion technology for Flash Smelting Furnace operations (T-FSF), and has also been able to extend the operating life of the Peirce-Smith converters. This paper will present several improvements implemented at the Tamano Smelter, and will discuss relevant P-S converter operation.

Jan 1, 2005

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, Nevada began large-scale production in 1977. During 2008 Round Mountain Gold Corporation (RMGC) relocated the primary crusher facility approximately 300 meters (1,000 feet) to make room for the next phase of open pit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17 meter (56 feet) high Mechanically Stabilized Embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, Colorado. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design, and construction of the MSE wall.

Jan 1, 2009

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

Entry of personnel under a vertical raise bored hole is not standard practice in Australia. Where access is required below a rise, mining operations must be confident that they understand the capacity of the ground control specified and installed. Physical modelling was conducted on Callie mine to evaluate the performance of 5 mm steel wire weldmesh secured to the base of a vertical raise bored hole of 1.4 m diameter. Joint orientation data was used with Unwedge to calculate a series of potential wedges likely to form within the rise. The mass of the most likely wedges were then replicated by collecting rocks in 5 kg increments (¦10 per cent), which were allowed to freefall onto installed mesh at the base of a 40 m vertical rise. The results indicate that two sheets of mesh can retain a freefalling rock of at least 20 kg mass although rupture of strands can result. This paper outlines the test conditions, expected results based on theoretical calculations and actual outcomes of the testing.

Nov 25, 2010

Improve the Bureau-developed system for locating and communicating with miners trapped underground following a mine disaster. Approach Include in the wireless system a portable second-generation transceiver that is more reliable, compact, easier to deploy and operate, and ruggedized to withstand a mine environment. How It Works In an emergency, the new transceiver is snapped onto a caplamp battery for power. (Normally the 1 1/2-pound transceiver is either carried by the miner or is strategically located in the mine.) Its antenna wire, coiled inside the transceiver container, is removed and deployed in a roughly square configuration around a coal pillar or on the mine floor. The antenna consists of 300 feet of lightweight wire, which provides a large magnetic moment while remaining intrinsically safe, The photograph shows the

Jan 1, 1981

By J. A. Finch, T. Weber

"Bubble size in flotation is strongly influenced by frother concentration in the pulp liquor. There is no accepted method of judging the dosage and thus how effectively frother is being distributed to control bubble size is not known. This will hamper certain plant test work where constant bubble size (e.g., when comparing reagents) is implicit. Bubble size is not easy to measure in plant and gas holdup is suggested as a surrogate in the development of a proposed “meter” to estimate frother concentration. The meter is calibrated to enable frother concentration to be estimated on samples drawn from any location in the flotation circuit. The meter and its calibration are described.As general background the action of frothers in reducing bubble size by retarding coalescence is discussed and the bubble generation systems for which the effect will be important are considered.INTRODUCTIONBubble size is an important variable in flotation. The flotation rate constant k has been related to mean bubble size Db by k % Db -n with n ranging up to 2 (Ahmed and Jameson, 1989) and even 3 (Yoon, 1993). Recent work has introduced k % Sb, the bubble surface area flux, given by Sb = 6 Jg / Db (where Jg is the superficial gas velocity or volumetric gas rate per unit cell cross-sectional area), i.e., n = 1 (Gorain et al., 1998). Regardless of the exact value of n, the significance of bubble size in flotation remains. In many plant trials it will be implicit that bubble size has not changed and attention will focus on other process variables. The measurement of bubble size, or a surrogate, would be useful addition to any test work.The size of the bubbles is influenced by several variables, gas rate, gas injection system (e.g., impeller design and rotation speed in a mechanical cell) and pulp composition (chemicals added, percent solids), but the most important is frother concentration (Harris, 1976). The frother functions by retarding coalescence (see appendix), which acts to preserve the small bubbles generated in the pulp (and permits a stable froth to form on top of the pulp). The measurement of bubble size is thus related to measuring frother concentration. The distribution of frother and whether sufficient (to control bubble size) is reaching the intended parts of the circuit then become important considerations. At present there is no simple way to judge frother concentration in a plant. In this communication we introduce a possible methodology, a “frother concentration meter”."

Jan 1, 2003

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation's reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

By M. E. Rossi, J. E. Camacho

"Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations to assess the uncertainty of mineable reserves at the project’s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the correct (or accurate) characterization of uncertainty, adequately describing the variability observed from the data and its effect on the final objective.The objective of this paper is to compare the ad-hoc uncertainty model provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered, the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme.The application described in this paper is taken from a medium-sized Cu open pit and underground mine in northern Chile, and demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more traditional resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit."

Jan 1, 2004

By Michael Schmitz, John A. Organiscak

ABSTRACT: A method (patent pending) has been developed to determine the quality of environmental cab filtration systems. This method utilizes specially configured filter cartridges to remove carbon dioxide from the ambient air with the environmental cab’s air filtration system. A real-time gas monitor is placed inside an unoccupied cab with the filtration system running to time decay the carbon dioxide to its lowest concentration or equilibrium level. The outside carbon dioxide concentration level can be measured concurrently with another gas monitor or with the same inside cab gas monitor during a representative period before and after the inside sampling is conducted. Cab filtration system leakage is comparatively deduced from the difference between the special cartridge filter efficiency and overall cab efficiency. Laboratory trials have illustrated that desirable high efficiency test filter configurations (greater than 99 % efficiency) can be devised, but have air quantity and test time limitations. These trials also demonstrated that CO2 penetration was reflective of controlled air leaks around a high efficiency filter under equilibrium conditions. This report examines the elements of this patent pending method.